Search Documents

By Theophili CN, Kapenis AP

Seismic tomographic imaging has been applied to determine the blast induced damage zones in bauxite pillars in underground mining. At the retreating stage, when pillar dimensions are reduced from 8 x 8 m to approximately 5 x 5 m, the' seismic tomographies reveal, through measurements of the P-wave velocities which is a measure of the degree of fracturation of the pillar rock mass, the presence of three zones within each pillar. In the external zone, where velocities recorded are below 750 m/s. extensive pillar damage occurs which is attributed to both the growth and coalescence of pre-existing cracks and even the creation of new cracks in the rock mass. This effect is in agreement with literature, when considering the peak particle velocity as a criterion for rock failure in tunnels. In the intermediate zone, where velocities range between 7S0-1000 m/s, damage to a much lesser extent occurs which is due mostly to growth of pre-existing cracks and widening of their apertures. The inner zone, where velocities exceed 1000 m/s, is considered to be unaffected by blasting. Simple remedial measures of low cost, which are based on blasting mechanics are proposed to minimise the blast induced damage zone and consequently the transition zone.

Jan 1, 1995

By Woodcock J. T, Sparrow G. J

Activated carbon particles obtained from a number of Australian CIP operations were examined with an optical and a scanning electron micro- scope and an electron microprobe. External surfaces, and polished sec- tions through individual particles, were examined with special reference to materials on the surface and to calcium and gold distributions. Photographs are presented of surface contamination of the particles by salts precipitated from the pulp such as calcium carbonate (calcite), calcium sulphate (gypsum), and a magnesium salt; ore minerals such as quartz, hematite, pyrite, arsenopyrite, pentlandite, and various alumino- silicates; and other substances such as grinding media and a fungus. Calcite was very abundant but the other materials were less common. Contamination in the interior of carbon particles was almost exclu- sively calcium carbonate, and extensive contamination extended to the centre of some particles. A possible mechanism for the formation of cal- cium carbonate inside the carbon particles is noted. Gold X-ray dot maps of sections through carbon particles indicated that gold was distributed throughout coconut shell carbons and that although gold was more concentrated near the outer surfaces of extruded peat carbon particles, it was also present to depths of at least 500 ¦m. The gold distribution throughout the carbon particles was similar to that rf alrit~

Jan 1, 1988

By Li YQ, Yoon RH

The photoresponse of natural mineral pyrite and galena electrodes has been studied in aqueous solutions on freshly fractured surfaces (some fractured in situ) using moderate overvoltages. When fractured in situ, the electrode potential of both minerals instantly drops several tenths of a volt. Pyrite exhibits a spontaneous anodic photocurrent at fracture, which indicates upward band bending (depletion layer) on the n-type electrodes. The negative surface charge responsible for the depletion layer is believed to arise from a surface state that is intrinsic to pyrite surfaces, possibly modified by hydroxide ion adsorption. The flat band potential, Vty, of pyrite is at approximately -1.0 V (SCE) at pH 9.2 but to reach V(b, pyrite has to be cathodically decomposed. In contrast, galena assumes the flat band potential at fracture. Subsequent polarisation of galena at potentials positive of Vth produces an anodic photocurrent (upward band bending) and polarisation negative of Vro a cathodic photocurrent. Most of the galena electrodes studied were degenerate n-type and at potentials negative of Vtb, no cathodic photocurrents are observed, indicating the bands cannot be bent downward, consistent with the Fermi level at the surface merging with the conduction band edge near Vn,. Several were close to intrinsic, with the photocurrent changing sign near Vn,.

Jan 1, 1993

By Kendall W. T C

This paper provides a brief overview of the history of the Chaffers Dewatering Project which was successfully commissioned in August 1993. Until the end of 1992 the `Superpit' and the deep mines of the Golden Mile had all been dewatered by a staged pumping system from the 28 level in the Lake View Shaft, which was removed at that time when the Lake View Mine was absorbed into the Superpit. Feasibility analysis had indicated that adaptation of oil industry technology offered the greatest potential for a low cost solution to the problem of dewatering the open pit and deep mines. A KCGM engineer and one of the authors visited the Jackson oilfields to look at the deep well pumping technology in use there in early-1991. In the final analysis a new dewatering station was established in the 23 level crushing station of the Chaffers Shaft using conventional plunger pumps, but the rising main was screwed 178 mm OD (7 inch) casing the suspended from the surface to a depth of 686 metres, and was installed using oilfield personnel and methods. Only the second installation of its kind in Australia, the project achieved the dewatering objective at about half of the capital cost of the more conventional approach and at lower operating costs as well.

Jan 1, 1995

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992

Indiscriminate surface disposal of coal waste in New South Wales has created a serious fire hazard and increased air pollution.A survey of numerous dumps, as well as particular investigations of one badly-constructed dump, showed that factors conducive to ignition and propagation of fires in waste dumps were high contents of combustible material (coal, pyrite, wood. paper. grease), size segregation leading to ready movement of air and moisture shape of the dump (e.g. protruding sections or porous junctions), high ambient air temperatures, bush fires, and even deliberate lighting.Control methods applied in the past tended to be haphazard and unsuccessful. Under Australian conditions the technique recommended for control of existing dump fires, based on experimental work, is to spray the dump with a chemical fire retardant (e.g. a 2 per cent solution of sodium tetra borate and ammonium phosphate), to cover the dump with a suitable soil, and to seal the surface with a I per cent solution of aluminium sulphate or sodium metasilicate. The recommended method of dump construction to prevent fires is to level and seal the site, to construct a firebreak around the dump area, and to build a rectangular dump with minimum size segregation and compacted surfaces.

Jan 1, 1971

By Mostyn G

In the last three decades various theories have been presented to allow the estimation of the force required to cut rock. These have generally relied on an hypothesised mechanism of chip formation.The paper presents results of an experimental program completed on an unjointed artificial rock in which the force and chip geometry were measured during deep cutting with a quarter scale bulldozer tyne. The program included various depths of cut and artificial rock of varying strength. The experimental results are compared with predictions based on three expressions for cutting force. Generally the measured forces are within the range of those predicted but none of the methods predicts the cutting force with any accuracy. It is considered that the discrepancies are due, in part, to the fact the that actual shape of the chip formed in deep cutting is quite different to that assumed in developing the theories and thus the theories cannot be expected to predict the cutting forces. It is concluded that Evans and Nishimatsu's theories predict lower bound estimates of the horizontal cutting forces. Deliac and Fairhurst's approach appears to over estimate the forces required to cut rock. New methods of prediction are required based on the observed mechanisms of failure.

Jan 1, 1993

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988

By Alwan M

At Binebase mineralisation is hosted within an andesitic Neogene volcaniclastic succession on Sangihe Island, Indonesia. Two major alteration types occur; an initial widespread phyllic assemblage of quartz -illite with chlorite, smectite, gypsum and pyrite, and a superimposed quartz - barite - sulphide assemblage. The phyllic alteration arose from a neutral to weakly acidic hydrothermal solution of greater than 200 degrees C, and the quartz - barite - sulphide assemblage arose from a cooler slightly more acidic fluid. This second alteration event is interpreted to have selectively replaced permeable volcaniclastic breccias and coarse lithic tuffs within the altered sequence. Gold and silver mineralisation is associated with the latter alteration, and is locally controlled by the degree of silicification and sulphide abundance. The sulphides present are pyrite, covellite and chalcopyrite. The sulphides are very fine grained with colloform and framboidal textures and were deposited contemporaneously with the bulk silicification of the coarse sediments. A large portion of the mineralised rock has been oxidised to a quartz - barite -limonite - goethite - jarosite assemblage.Coincident gold, silver and antimony geochemical soil anomalies gave the best correlation with anomalous gold and silver grades in bedrock as identified by drilling. Resistivity proved a reliable geophysical method for delineating zones of silicification.

Jan 1, 1990

Copper was first produced in Australia in 1844, at the Kapunda Mine in South Australia, and, by 18i>0, production exceeded 2,000 tons of copper a year. Output increased ,steadily, reaching a peak of 14,00Qo tons a year in 1867 and 1868, when the Burra Burra and Kapunda Mines in South Australia and the Peak Downs Moine at Clermont, Queensland, were at the height of their production. At this period, Australian copper formed a considerable percentage of the world's supply, its output equalling, for a short time, that of the United States. Production declined to between 3,000 and 4,000 tons a year after the closing of' these three mines between 18717 and 1879, and, at this stage, the Australian output came chiefly from the Wallatoo and Moonta mines in South Australia. About 19000, it began to rise again, with the extension of the railway to the copper fields of Chillagoe and Cloncurry, and, between 1905 and 1912, was at its greatest, with a maximum of 47,774 tons of copper in 1912. During this period, Australia contributed 4,7 per cent. of the world's annual production, and ranked among the six major copper-producing countries of the world (Table 1).

Jan 1, 1943

By Borshoff J, Von Pechmann E

The uranium mineralization in the White's East area of The Embayment is hosted by Lower Proterozoic schists of the Masson Formation which have undergone polyphase de- formation and upper greenschist metamorphism. Significant mineralization is also present in apatite rocks. The ore zones occur near an unconformity with overlying Middle Proterozoic sandstone and breccia conglomerate. Kink breccias and fracture systems related to post Middle Proterozoic reverse faults are the con- trols for mineralizing fluid migration. Pitchblende is the main uranium mineral and it occurs as fine disseminated grains, fibrous webs, clusters composed of botryoidal aggregates and locally as veins. Two genera- tions of uranium mineralization are present. The first generation (pitchblende I) occurs as fine grained inclusions within chlorite II, and the second (pitchblende II) as hydraulic fracture networks and massive veins intimately associated with sericite-hematite-chlorite III. Two hydrothermal alteration phases have affected both Lower Proterozoic and Middle Proterozoic sequences. The most extensive alteration mineral is chlorite, of which a number of varieties has been identified. Mg-rich chlorites are generally associated with the first phase alteration assemblages and are commonly replaced by hematite, seri- cite and Mg-Fe chlorites in massive pitch- blende zones. Other alteration minerals in- clude tourmaline, apatite, talc, quartz, magnesite, graphite, pyrite and rutile.

Jan 1, 1984

By A E. Annels, M D. Raine, I M. Platten

Lode-gold systems are often characterised by a high to extreme nugget effect (>50 per cent), and the presence of coarse gold particles (>100 ¦m in size). They rank amongst the most difficult of ore deposits types, in terms of producing an accurate and precise resource estimate. Their effective sampling is generally difficult because of the relatively low concentrations involved and erratic nature of the gold particles. Grade continuity is usually less consistent than gross geological continuity, and is typified by the localisation of grades within discrete oreshoots. In most cases drilling, particularly diamond drilling is an effective measure of global geological continuity, whereas grade can only be reliably resolved from underground development. Depending upon drill density and geology, it is unlikely that anything above an Inferred Mineral Resource can be estimated from surface drilling alone. Underground development, in-fill drilling and, potentially, bulk sampling or trial mining will be required to delineate Indicated and Measured Mineral Resources and subsequent Ore Reserves. Grade estimation will have to account for highly skewed and often multi-modal populations, extreme values, a high nugget effect and low geostatistical ranges. A clear geological model that honours both geological and grade continuity must drive the resource estimation process.

Jan 1, 2003

Gold-rich porphyry copper deposits areimportant sources of gold in the circum-Pacific region: 26 major deposits contain >7000 tonnes of gold. The deposits occur in a variety of subduction-related settings, and may be underlain by crust that is undergoing either extension or compression and that is either oceanic or cratonic in character. The deposits are associated intimately with composite porphyry stocks, which commonly were emplaced into coeval andesitic volcanic piles. The stocks range in composition from low-K calc-alkaline through high-K calc-alkaline to potassic alkaline. Much of the copper and gold were introduced as components of K-silicate alteration, which may undergo partial overprinting by intermediate argillic assemblages. Advanced argillic alteration is widespread in the shallow parts of the systems whereas sericitic alteration at deeper levels tends to be restricted. Gold distribution generally follows that of copper, which is present mainly as chalcopyrite with or without bornite. The gold is in the native state and occluded by cr in close proximity to the copper-iron and/or iron sulphides. The magmas and metals necessary for the generation of gold-rich porphyry deposits were derived mainly from subcrustal sources, with the subducted slab believed to play a pivotal role.

Jan 1, 1990

Rockbursts, as they occur in South African deep level gold mines, have a lot in common with natural earthquakes. Both violently release seismic energy and cause damage to underground and surface structures. Rockbursts are the main cause of fatalities in deep gold mines and the problem may increase in severity with future mining at greater depths. Although the emphasis in Rock mechanics is on the prevention of rockbursts, prediction would provide a partial solution to the rockburst problem. A research project was initiated in 1981 on Western Deep Levels to investigate the possibility of detecting and identifying precursive microseismic activity. This project has succeeded in locating potential sources of seismic events with reasonable confidence. The timing of these events may be estimated with less confidence, and an important parameter, namely the potential size of the rockburst, still cannot be determined. An example of a large seismic event and its associated precursive activity are discussed. Practical prediction systems will, at least for some time, involve subjective decision making which will place a new responsibility on the mine manager as well as the rockburst specialist. The moral pressure on the manager as the final decision maker will probably be greater than the fear of leqal prosecution.

Jan 1, 1986

By Scherbatsky VB, zon BM, Babushkin NM, Kitaev BI, Shabel&apos

The structure and hydrodynamics of the raceway zone of a blast furnace was studied on a cold model representing a sector containing two tuyeres. The model differed from the usual in that it was prov- ided with continuous flow of the coke layer at pre- determined rates, had provision for changing the tuyere parameters (diameter, protrusion, inclinat- ion) and irrigation of the layer with liquid. A combination probe was developed which per- mitted simultaneous measurement of the pressure field both across the area and through the height of the layer as well as determining the topography of the raceway. The velocity fields in the layer were measured with a specially made impulse thermo- anemometer. The determining criteria of the model were taken as the relationships between the energy of the blast and the particles, the dimensions of the raceway and the cross-section of the tuyere. The model established the effects of the tuy- ere structural parameters, blast parameters and amount of liquid products of smelting on the con- figuration of the raceway, the structure of the layer, pressure and velocity fields in the vicinity of the tuyeres and in the vertical direction through the layer. The properties of the raceway formation and the structure of the layer in motion have been clarified.

Jan 1, 1981

Laboratory experiments have been used tostudy a wide range of convective processes which are significant for the formation of rocks and the ores that form in them. Metal-rich solutions flowing through the sea floor produce 'black smoker' chimneys; both the size and structure of a solid chimney and the height to which the plume of effluent rises above it can be predicted using model experiments. Analogues of processes in solidifying magmas can also be studied using crystallizing aqueous solutions. The release of lighter or denser residual fluid as crystallization proceeds, and the resulting compositional convection, have a vital influence on the differentiation of initially homogeneous magma and on the evolution of stratified magma chambers. Mixing during the replenishment of magma chambers, and its dependence on the rate of filling and on the fluid properties, have also been studied on the laboratory scale. Experiments carried out in different geometries have been applied here to the formation of platinum and chromite ores and komatiite lavas. Larger-scale mantle convection, in particular the motion of subducting plates and plumes rising from the core-mantle boundary, also determine the tectonic settings in which ore bodies form. These phenomena too can be usefully investigated in laboratory experiments using very viscous fluids.

Jan 1, 1990

By Gemmell J. B

Zinc-bearing massive sulphide deposits have been mined in Tasmania since 1900. The current major producers are Hellyer and Rosebery, with total resource tonnages (mined plus reserves) of 16 Mt (million tonnes) and 24.8 Mt respectively. These deposits belong to the class of seafloor volcanic-hosted massive sulphides (VHMS) and are located within the Mt Read Volcanics, a narrow belt of continental margin calcalkaline volcanics of Cambrian age. Compared to other Australian VHMS deposits, and world-wide MVT and Sedex deposits, the Tasmanian examples clearly stand-out due to their high metal grades, averaging over 17 per cent Pb+Zn. The deposits vary in morphology from mound style (Hellyer) to sheet style (Rosebery) with other combinations including stacked lenses (Que River) and disrupted cross-cutting bodies (Hercules). All deposits show the classic VHMS zonation from an Fe-Cu-bearing base to a Zn-Pb-Ba-rich top. Zinc, gold and silver tenor commonly increases toward the stratigraphic top of the deposits. The ores have been deformed during regional metamorphism, resulting in folding, shearing and recrystallisation of sulphide lenses. In addition to the major deposits, a number of small massive sulphide prospects occur throughout the volcanic belt and the potential for the discovery of further large, deeply buried deposits remains high.

Jan 1, 1993

In order that the processes seen may be followed in their proper 'order, the subject will be dealt with as follows, (1) Wallaroo and Moonta Mines; (2) Wallaroo and Moonta Mines Smelting Works; (3) Broken Hill Mines; (4) Concentration at Broken Hill; (5) Smelting and refining of Lead, Silver, and Gold at Port Pirie. The first acquaintance with the copper region was made at the Yelta shaft and dressing mill of the Parramatta Copper Mines Co. at Moonta. The country rock at Moonta is a hard, tough, felsitic porphyry, the copper lodes having a general strike of N. 30° Kilipping from 500 to 70°. This necessitates shaft-sinking on the lode, and underlay shafts are the rule on the field. The ore is raised in the Yelta shaft in wheeled skips, and consists of ·chalcopyrite, bornite, pseudomorphic hematite, containing, in addition, molybdenite and tourmaline. The ore from the bins at the brace is passed over a grizzly; the over-size is hand-picked into smelting ore, concentrating ore, and waste rock (00 attle ), which is sent below for filling. The under-size is elevated to a trommel having in. holes. The over-size falls on to a picking belt made up of lengths of rope strapped with iron, working over wooden pulleys.

Jan 1, 1907

By Segnit ER, Jensen G

The decoppering of soft and hard leads was investigated by stirring in an open pot, using sulfur or sulfur plus pyrites, or sulfur plus pyrrhotite, as reagents. Lead samples taken during the process were analysed for copper. Dross samples were examined by optical micro- scope, SEM and XRD. Soft lead containing silver can be decoppered satisfactorily by stirring with 0.1% S at low temperatures - close to 330¦C. Soft lead, whether containing silver or not, can be decoppered satisfactorily at higher temperatures by stirring with 0.1% S plus 0.4% pyrites. Then CuFeS2, Cu5FeS4 and PbS are formed, instead of Cu2S, CuS and PbS when using S alone. Hard lead containing tin can be decoppered satisfactorily by stirring with 0.1% S at temperatures from 320-400¦C. When stirring with 0.1% S plus 0.4% pyrites, reversion of copper from dross to lead on prolonged stirring does not occur. Hard lead without tin can be decoppered with S plus pyrites better than with S alone, but the presence of antimony hinders the decoppering, which is less effective on lead with 5.5% Sb than with 2.3% Sb.

Jan 1, 1980

Black coals occur in most of the major sedimentary basins in Australia. In addition to the better known Permian coal occurrences of the Sydney, Bowen, Oaklands and Galilee Basins, coals of Permian age occur in the Arckaringa Basin in South Australia, the Bonaparte Basin in Northern Territory and the Collie, Perth and Canning Basins in Western Australia and the Tasmania Basin in Tasmania. Coals of Triassic age occur in the Ipswich Callide and Tarong Basins in Queensland, the Tasmania Basin in Tasmania and the Leigh Creek area in South Aus- tralia. Coal bearing rocks of Jurassic age occur in the Mulgildie Basin and Maryborough Basins in Queensland and in both the Queensland and New South Wales portions of the Clarence Moreton Basin and Surat Basins. They also occur in the Perth Basin in Western Australia. Rocks of Cretaceous age known to contain coal occur in the Styx, Maryborough and Laura Basins in Queensland, the Gippsland Basin in Victoria and both the Queensland and New South Wales portions of the Surat Basin. The coal measures have been deposited in a variety of sedimentary environments and the coals vary widely with regard to thickness, extent, banding characteristics, maceral and ash content. However, they are generally of low rank and most are suitable only for steaming.

Jan 1, 1975