Search Documents

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By J L. Macdonald, G S. King

"The development of a predictive geometallurgical model is a multidisciplinary and iterative task that involves both discovery and integration aspects. In this paper, the authors discuss the concepts of geometallurgical modelling in terms of the underlying relationships that are used to connect geology, metallurgy and economic value, and how the early-stage preparation of a spatial geometallurgical model enhances project value and provides a sound basis for future studies and test work programs.Hot Chili’s (copper-gold-molybdenum) Productora Project, which is located in northern Chile, is a porphyry-copper style deposit that can be exploited using open pit mining and preparation of a saleable concentrate from fresh ore, as well as heap leaching, solvent extraction and electrowinning (SX-EW) extraction of copper from oxide ores. To enhance project value in the Productora prefeasibility study (PFS), Hot Chili developed a geometallurgical model that was used to predict the process responses of both sulfide and oxide ores. The Productora model incorporates test results from mineralogical, metallurgical and comminution testing, as well as other studies completed on a suite of samples collected from the many geological domains of the deposit.Using Bond Work Index and Abrasion Index proxies in the geometallurgical model, Hot Chili estimated the variability of sulfide ore throughput and comminution costs. Heap leach acid consumption in oxide ore was estimated from drill hole calcium concentrations. The model was then used in mine scheduling to identify high and low throughput or high and low acid ore zones so that the processing of these zones could be advanced or deferred to improve net present value (NPV). Additionally, the cost benefits of preparing an early-stage geometallurgy model were quantified through a comparison to a conventional model that was based on test work averages.CITATION:King, G S and Macdonald, J L, 2016. The Business Case for Early-stage Implementation of Geometallurgy– an Example from the Productora Cu-Mo-Au Deposit, Chile, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 125–134 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M Dunglison, P M. Cameron

Simultaneous mass-balancing of a mineral processing flow sheet results in adjustments to each data point that reflects the accuracy and precision across the full set of data. In this way, all the good work that goes into designing the sampling and analysis protocol for each sample point is leveraged in order to produce a æbetterÆ set of balanced numbers for every sample point in the circuit. Few operating plants employ whole of circuit balancing techniques to produce reported operating results. This situation is changing with the application of mass balancing technology which utilises redundant data for production accounting and metal reconciliation from product to ore source across multiple phases and multiple time periods. Mine and plant data can now generate credible information to improve productivity. Mine and plant personnel can now use consistent data sets for review and planning. Decisions based on balanced data can be made quicker and with increased confidence.

Jan 1, 2005

Professional engineers of today require a wide array of experience and knowledge. It is true that commonly engineering degrees do teach the technical requirements well, but do fall short in the way of teaching other non-technical issues of professionalism to the student. Today calls for an engineer who does not only have a high standard of the technical knowledge required for their degree, but also has a broad range of experience in areas that are becoming increasingly important in engineering. The importance of social responsibility, liability and interpersonal relations is high. Through the face of the changing world, it has become clear that there is a need for a new type of engineer, who has a broad range of expertise, as well as the typical technical abilities required. This paper will outline these non-technical issues and propose ways of combining these ideas into the mainstream engineering degree.

Jan 1, 2004

By N Bezuidenhout

The performances of ten field-scale experimental final covers were evaluated over an eight-year period. The covers were evaluated as part of the rehabilitation of acid generating coarse coal reject dumps and opencast coalmines in the Northern KwaZulu Natal province in South Africa. The main purpose of the experimental covers was to restrict rainfall infiltration into acid generating coal discard. The mean average rainfall over the monitoring period was 839 mm with 84 per cent occurring between October and April. The average evaporation was 2100 mm. The site is described as a ædry siteÆ since the evaporation exceeds rainfall by a significant margin. Approximately 30 per cent of rainfall infiltrated the uncovered cells. Rainfall infiltration into the fine coal discard was reduced to 20 per cent and 15 per cent for a 300 mm and 500 mm cover respectively. Infiltration was reduced to ten and 12 per cent of rainfall for fine coal discard provided with a 1000 mm double soil cover and a compacted bottom layer. This relatively high infiltration was probably caused by moisture being entrapped in the bottom retentive layer, and not being released by evapotranspiration. The best performing cover comprised 1000 mm single soil with a compacted bottom layer and infiltration was reduced to four per cent of rainfall. Rainfall infiltration into sloped cells varied between seven per cent and 14 per cent of rainfall. The computer software, SoilCover, was used to predict infiltration and moisture content in the cover. Predictions of rainfall infiltration were accurate, but were less accurate for covers where the hydraulic properties of field compacted soils were not adequately characterised. Oxygen ingress was significantly reduced for cells provided with a 1000 mm cover. Oxygen concentrations were generally below one per cent, with the exception during exceptionally dry periods when the cover dried out, resulting in increased oxygen ingress. For other covers, and the uncovered cells, oxygen concentrations were close to atmospheric concentrations. During the eight-year monitoring period, acid breakthrough occurred in five of the cells, including three uncovered cells, one cell with a 300 mm cover and one sloped cell. In contrast, cells covered with 1000 mm, bottom compacted soils shows a marked improvement of leachate quality, indicating that sulfide oxidation processes have been slowed. There was a distinct relationship between oxygen ingress and leachate quality for all of the cells. No cover degradation was evident over the eight-year period, except for some erosion observed on a sloped cell. The results indicate that the onset of acid drainage can be delayed by perhaps hundreds of years and salinity loads can be reduced by more than 90 per cent, if coarse coal reject dumps in the KwaZulu-Natal provinces in South Africa are provided by an adequate cover system. These research outcomes can be extrapolated and applied to other dry site regions where similar materials are being considered.

Jan 1, 2003

Modern technology and the need for published results have created the tendency for exploration to concentrate on drilling and assaying rather than building a broader geological understanding. Though grade is vitally important to a resource estimate, density and volume are also very important aspects that require equal consideration. Wet tropical nickel laterites are developed in humid environments over ultramafic bedrock where the nickel and cobalt are enriched to economic levels by weathering, leaching and supergene processes. These laterites often occur over rugged terrain at higher elevations where there is sufficient rain and stability for the long lateritisation process to occur. For nickel laterite profiles, the variable terrain and significant material type changes within the relatively thin profile make density and particularly volume estimation, just as significant as grade in resource estimation and assessment of resource risk. Drilling alone is generally not a cost-effective way to reduce the risk in laterite volume estimation to acceptable levels. Surface geological mapping, high resolution topographic data and other information such as ground penetrating radar (GPR) can be used very effectively to improve volume estimates. These data types are all differently structured, have different data density and quality and may potentially overlap. Integration of these disparate data types provide the most cost-effective approach to modelling wet tropical nickel laterite volumes and minimising risk. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By L Scheunis, A Van den Bulck, E Jak, K Verbeken, M Shevchenko, R Starykh, I Bellemans, P-J Boeykens

As a result of the globally increasing consumer use of electronic devices, it is expected that pressure will increase on the supply chain of precious metals. Hence, recycling of these electronics becomes increasingly important, as well as optimising the current processes. One major issue in metallurgical processes is the amount of metal that is lost into the slag. This metal loss is inherent to the production process and therefore, additional processing steps such as slag cleaning may be required. Slag cleaning can be done in electrical resistance furnaces where heat is produced using the Joule effect, making the slag’s electrical conductivity an important operating parameter. Since slags are ionic liquids, the electrical conduction happens via the movement of ions which is called ionic conductivity. However, within the presence of transition metal oxides, a second mechanism of conductivity occurs as electrons are able to hop from one transition state to another, which is known as electronic conductivity. As ‘FeO’ is a common slag component in the non-ferrous pyrometallurgical industry, both mechanisms are present, but their proportions vary with the respective amounts of the two forms of the multi-valent ions and hence, with the oxygen partial pressure. The goal of the present study is to develop an experimental set-up and methodology for measuring the electrical conductivity of synthetic SiO2 – CaO – AlO1.5 – ‘FeO’ slags at various oxygen partial pressures.

Jun 19, 2024

By D Akis, A Clark

The Lihir gold operation, located in the New Ireland Province of Papua New Guinea (PNG), approximately 900 km north of Port Moresby, was commissioned in 1997 under the management of the Lihir Management Company, a subsidiary of Rio Tinto. This management period ended in 2005 with Lihir Gold Limited (LGL) becoming self-managed. LGL is now the largest listed company in PNG and a top tier mining company in Australia. The focus of the operation since 2005 has been to take advantage of strong market conditions to increase cash flow while driving operating costs into the lowest quartile of gold producers. During this period production has increased through capital expansions, most notably with the addition of a flotation circuit, and through culture change and efficiency improvements. The next step forward for the Lihir operation is a major plant upgrade to increase production to an average of around one million ounces per annum by matching the ore processing rate to the ore mining rate. The key benefits of this project will be the addition of approximately 240 000 ounces per annum of gold production, the access to an additional one million ounces of gold and the ability to meet all stockpiling requirements. The Lihir operation has come out of the boom period in a strong position, is undertaking a major upgrade at a time when prices are low and labour is available, and will be positioned to take advantage of future opportunities as they arise.

Jan 1, 2009

By B Roberts

The Department of Industry and Resources (DoIR) is responsible for several sets of legislation, which, among other things, regulate the storage, handling and transport of dangerous goods as well as every aspect of the life cycle of explosives in order to prevent explosions, fires and spillages. The legislation with particular relevance to explosives includes: The Explosives and Dangerous Goods Act 1961; the act deals with the storage, manufacture, sale, import, authorisation and use of explosives. It is primarily framed for use of explosives and fireworks in the general community but also has relevance for storage on mine sites. The Dangerous Goods (Transport) Act 1998; this act regulates the transport of explosives on public roads, but not on mine sites. The Mines Safety and Inspection Act 1994 (MSI Act); this act and supporting regulations deal with the full spectrum of occupational health and safety in the mining industry. There is a substantial section in the regulations dealing with the use of explosives at a mine site.DoIR has identified the need for security upgrades of the Government Explosives Reserves, the need to tighten security measures at mine sites, the need for improved security checking for licensed shotfirers and the need to restrict the availability of explosives to authorised people who have had appropriate security checks. It is also clear that we need restrictions on the sale and use of ammonium nitrate (AN). A number of additional security measures are being proposed and all proposals are being refined by ongoing industry consultations. These will be adopted into new explosives regulations in association with the new Dangerous Goods Safety Act 2002 (DGS Act). Government finalised the act in June 2004. The act remains dormant until new explosives and dangerous goods regulations have been prepared. When the DGS Act and a suite of regulations are proclaimed as a package, sometime between December 2004 and April 2005, the old legislation consisting of the current two acts, will be automatically repealed. It is also proposed that all explosive regulation, including those under the MSI Act will be consolidated in one place under the DGS Act for user friendliness.

Jan 1, 2004

By C Mark, Z Agioutantis

This paper presents an empirical design methodology that is based on successful US roof support systems using both primary and secondary support in coal mining entries and intersections. The recent nationwide dramatic reduction of roof fall rates, especially in areas with weaker roof, can be directly correlated to the effectiveness of the roof support systems. A large database of roof fall histories at several mines is used to define the approximate boundaries of three modes of roof support with respect to roof strength as classified by the Coal Mine Roof Rating (CMRR) and in situ vertical stress as indicated by the depth of cover. These roof support classifications are: • Suspension, where roof bolts mainly provide skin control for strong roof. • Beam building or reinforcement, where a roof of moderate strength can be supported by roof bolts only. • Supplemental (secondary) support, where the primary support by roof bolts may be augmented by several secondary support systems, eg cable bolts, trusses, additional roof bolts or standing supports. The Primary Support Rating index (PSUP) captures the capacity of the primary roof bolt system as a function of the actually implemented roof control plan, ie roof bolt length, roof bolt density, and roof bolt capacity, while it does not consider the type of bolt. The actual PSUP value is compared against a suggested PSUP value derived from statistical analysis of US case histories. Where secondary support is indicated, the expected rock load determines the necessary capacity of the secondary support system. A new (free) software package, Analysis of Mine Roof Support (AMRS), implements the design methodology and also allows comparison with other international indices such as the Reinforcement Density Index (RDI), the PRSUP, etc.

Nov 29, 2022

The Prominent Hill copper-gold deposit is located approximately 150 km north west of Olympic Dam, on the southern margin of the Mount Woods Inlier in South Australia. Its discovery in November 2001 resulted from the application of a geological model developed from geological, geophysical and petrophysical data pertaining to the Olympic Dam deposit. The discovery has dispelled the notion the Olympic Dam may be unique, and that another deposit like it is unlikely to be found. The Prominent Hill mineralisation is hosted by haematite-matrix hydrothermal breccias, which have suffered extensive iron-sericite-silica alteration and overprinting. Copper, gold, barium, fluorine, uranium, cerium and lanthanum are all intrinsically associated with the hydrothermal iron. Breccias intrude an east-west striking, fault-controlled sedimentary succession, which is flanked to both the south and north by volcanic complexes. Many similarities between Prominent Hill and Olympic Dam are documented including geological setting, mineralogy, breccia styles, and alteration. Differences relate largely to the nature of the immediate host rocks. The similarities and difference provide key data for improving exploration models for this style of iron oxide copper-gold deposit, both within the Gawler Craton as well as globally.

Jan 1, 2004

By B Goebel, G Baker

The Australian Magnesium Corporation Limited (AMC) is constructing the worldÆs largest magnesium metal plant at Stanwell, 24 km west of Rockhampton in Central Queensland. The $1.3 billion, 97 000 tonne per year plant is scheduled to commence production in mid-2004. It will produce magnesium from magnesite using the innovative, locally developed AM Process Technology which enables magnesium to be produced at internationally competitive costs. The technology will enable the plant to have the lowest environmental impact of all the available magnesium production processes. The project will meet current world-best-practice environmental and emission standards while on a life cycle analysis, magnesium produced by the Stanwell plant will result in net reduction in global greenhouse gas emissions. Magnesium is the lightest of the structural metals. Its high strength to weight ratio and ease of casting and machinability makes it particularly suitable for the manufacture of light weight automotive components. Reducing the weight of motor vehicles through the use of light weight materials such as magnesium is the current primary means adopted by the automobile manufacturing industry to improve motor vehicle fuel efficiency and the lowering of emissions of greenhouse gases. The Australian Magnesium or AM process has been developed over the past decade by AMC in conjunction with the CSIRO to produce magnesium from magnesite mined at AMCÆs Kunwarara deposit. Over $200 million has been spent developing the AM process, designing, building and operating a demonstration plant at Gladstone and to complete an environmental impact statement and receive environmental approvals as well as funding for the commercial Stanwell Project. The paper outlines the development of the AM process technology, the operations of the Gladstone demonstration plant confirming the process technology, its operating costs and environmental performance. The paper covers the particular attention that was given to minimising the production of CHCÆs, the development of new cover gases for molten magnesium, the minimising of emissions of greenhouse gases and the life cycle analysis of magnesium as a replacement for steel and heavier metals in motor vehicles which confirmed its use resulted in a net reduction in global greenhouse gas emissions. The project received both Commonwealth and Queensland Government environmental approvals by August 2000.

Jan 1, 2002

By R Redden

"The Didipio Gold-Copper project in the Philippines has been a well-defined reasonably high gold grade porphyry for almost two decades. OceanaGold are now bringing the project into production in late 2012 and have recently reoptimised the project with the goal of combining the inherent high grades with higher through-put than previously proposed that will see strong initial metal production. The project was discovered and well defined by 1995, but has seen some obstacles to development, namely sovereign risk, capital cost and project funding. The project strengths over this time that have kept the flames alive are: strong grades large orebody with low stripping ratios a simple beneficiation process and a clean high-grade concentrate strong support from the Philippines government.The initial study in 1998 used Gold and Copper price assumptions of $325/oz and $0.95 lb respectively. Today reserves are based on $950 and $2.85. So, being a porphyry with a large reducing grade halo, the deposit now lends itself to extraction on a much larger scale than before, without any significant capital expenditure as a larger open pit now dominates the project.Didipio is a game changer for OceanaGold, so it has been important to learn from history and to capitalise on a strong initial metal production profile. The project sits in a reasonably remote mountainous area of Luzon which sees annual typhoons and numerous short duration high intensity rainfall events and two rivers flowing through the project area, so it has not been without some innovative technical solutions.CITATION:Redden, R, 2012. Didipio - Learning the lessons, adapting and getting ready for production, in Proceedings Project Evaluation 2012, pp 67-76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By Luck D

Current methods of mucking out small development tunnels are a major limitation to improved efficiency and high rates of advance. This is particularly true in the deep metalliferous mines of South Africa, where the harsh environment, remoteness of operations and the hard abrasive rock conditions mitigate against the use of the tunnel borer type of equipment. The Loader Distributor Train was designed to overcome the special problems of hard rock tunnelling. It combines advanced innovative technology with proven simple methods of operation and maintenance. The system aims at taking advantage of new, efficient and cost effective power sources in South African mines based on replacing compressed air with electro hydraulics and the new concept of hydropower. It also introduces electronics and computer technology, for both automatic control and fault finding, into the production environment. The system is designed to permit sophisticated equipment to be operated and maintained by a semi skilled labour force. Although still undergoing trials it is believed that the Loader Distributor Train will prove highly effective, and that the new concepts offer considerable potential in areas other than flat tunnels, in particular the cleaning of inclined shafts.

Jan 1, 1986

WMC Limited, owner/operator of Olympic Dam, the worldÆs largest underground uranium mine and the fourth largest underground copper mine has now completed an expansion that has been classed as a benchmark in the mining industry. To achieve a production increase from 3.4 to 9.25 Mtpa from an underground mining operation in two years was a major challenge, it was essential to review the overall materials handling system from æthe face to the stockpileÆ. The challenge was two-fold:How to deliver 30 000 tonne of ore per day to the processing plant, from a single underground mine? To provide the processing plant with a consistent metallurgical feed. This paper traces the transformation from the old to the new materials handling system at Olympic Dam.

Jan 1, 2000

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

A hidden asset in most exploration and mining activities is data. Common practice involves the spending of large amounts of money to discover, define and prove the viability of a mining project. Some organisations have used operations research analysis and internal costing methods to allocate a value to their data and to compare the costs of data maintenance to other more tangible activities like plant and equipment maintenance. Those organisations, which do not undertake such an analysis often, have little knowledge or understanding of the extent and the worth of their data. Often the organisations lack of knowledge and understanding of the data is indicated by their failure to fully exploit or realise their opportunities. The focus of this paper is to discuss new technologies that optimise the management and security of collected and derived data. The technologies discussed are components of the software systems acQuire and MineSight.

Jan 1, 1999

The extraction of world-class mineral deposits using massive underground mining techniques is not an entirely new theme to world mining companies and experts. Previous MassMin conferences have helped to gather and disseminate the valuable experience and knowledge so important for the proliferation of safe and efficient mining of large underground deposits. With the passing years since the first MassMin conference in Denver in 1981, a number of factors have contributed to an increase in massive underground mining around the world, including environmental pressures, gradual exhaustion of shallower deposits and the enabling effects of improving technology in disciplines related to underground mining. Massive underground mining is heading deeper, embracing challenges which include working with elevated temperatures, increasing in situ and mining induced stress levels and longer ore transport routes. Improvements in mineral processing technology will tend to lead operators to contemplate the extraction of lower grade orebodies in the event that the ore can be efficiently transported to the surface and hence the plant. No doubt this tendency, and its associated challenges is encouraging a rich growth in innovative engineering in such fields as mine planning and materials handling as well as geomechanical issues such as support design and the simulation of extraction sequence effects on stress re-distribution. MassMin 2000, we are sure, will showcase a wide variety of new contributions in thought and actions in these fields. There is a definite place for academic institutions and mining related suppliers in the process of developing new technologies and practices in support of present and future endeavour in this field. Dyno Nobel has its own part to play, certainly as an enthusiastic and proud major sponsor of MassMin 2000, but also by means of identifying common cause between our Vision and Values and the needs, present and future, of the underground massive mining industry. The critical success factors, which Dyno Nobel pursues are:health, safety and environment, customer relationships and market development, cost optimisation (while maintaining quality), technology and innovation, organisational development, and leveraging capabilities globally. Through the present paper we would like to share some of these values and offer some practical insights as to how their realisation will contribute to the achievement of MassMin goals and needs.

Jan 1, 2000

By D J. Robinson, L L. Kuhar

"Regardless of orebody value, at some stage, the pit will reach a depth where the reward for mining wider and/or deeper is not justified by the anticipated returns. ‘Last-blast’ strategies may help to some degree in recovering additional quantities of the resource but when a pit remains, there is often significant value left in the ground. In addition, in many cases, one or many good reasons may dictate why going underground and pursuing the orebody below the pit is also not justifiable. Whereas the company can hopefully move on to other more prospective parts of the orebody, the remaining options for the pit are usually very limited. Typically the pit is either held for potentially more favourable future pit expansion opportunities or it could be used for an alternative purpose, such as tailings or waste storage. This paper will present an alternative option that involves the direct extraction of values using in situ recovery (ISR) methods to recover additional value metals from the walls and/or floor of the pit. ISR involves circulating a fluid through the remaining orebody, solubilising the target metal and subsequently returning the solution to the surface for metal recovery. ISR is not the panacea to all but it has been employed selectively in the minerals industry for some time and the production of metals, such as uranium, rely heavily on this approach. ISR is not yet considered by many operators as an approach to compete with open pit or underground mining, largely because of the perceived limitations of this approach and the perceptions of risk. Rapid recent development of tools and enabling technologies relevant to ISR have made us reconsider the most economic approach to extracting many other metals from known mineral systems, even those currently listed as subeconomic. We suggest that ISR has the potential to make mine operators rethink the end of the pit life and adopt an innovative ISR approach to work toward a more complete recovery of value metals from existing pits.Citation:Kuhar, L L and Robinson, D J, 2016. In-pit In Situ Recovery - a New Approach That May Allow for Increased Value Extraction before Pit Closure, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 275–283 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

Anglo Platinum recognised with its expanded operations the need to change its evaluation strategy due to increased sample volumes and the pressure it created at laboratories. The sender/receiver analytical scenarios had to change in order to curb costs and to prevent substantial investments in new sampling and analytical facilities. Given the high cost associated with correct sampling systems and sampling protocols and the shortage of technical resources a strategy of single point sampling and analysis was introduced. The analysis was then done at an ISO17025 accredited laboratory with ten per cent checks, subjected to careful statistical scrutiny. Logistical problems increased with respect to weighbridge congestion, maintaining sampling quality, throughput of samples in the sample preparation areas, manual quality control systems in place, audit trails and analytical capacity throughout all operations. This required the expedited improvement of existing sampling practices and the development of new sampling methods and equipment. Anglo Platinum is classifying and standardising sampling equipment, sample preparation and analytical procedures for all process streams with the view to minimise overall uncertainties. Major investments were made into a customised LIMS and automated equipment for data management, reduction of manual transcription errors and streamlining of sample processing. Anglo Platinum is committed in rolling out the enhancements to all sites as priority dictates.

Jan 1, 2008