Search Documents

By B Mohanty, D Zwaan

Systematic near-field vibration monitoring of stope blasts was carried out in a large, deep underground mine. A total of 31 production blasts were studied in order to investigate the effectiveness of existing blast designs. This involved the vertical retreat mining method, which requires drilling a raise bore or blasting a slot raise (typically 1.22 m in diameter) using large diameter boreholes (165 mm). The diagnostic technique employed multistation near-field monitoring of blasts with high-g (100 g) and high-frequency (>10 kHz) triaxial accelerometers. The amplitude of the vibrations is correlated with the strain energy transmitted from each explosive deck. The results showed that more than 30 per cent of the explosive decks contributed little energy to the rock breakage process in these blasts, and an equal number contributed only inadequately. These findings are indicative of serious blast malfunctions. The problems can be traced to inadequate deck blast design and possibly to drill hole deviation. The various causes for such malfunctions are discussed and remedial measures suggested.CITATION:Mohanty, B and Zwaan, D, 2015. Assessment of underground production blast designs and blasting performance, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 607–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Thompson, E Villaescusa

The Western Australian School of Mines (WASM), Kalgoorlie, has been performing dynamic testing of reinforcement systems as part of the Minerals and Energy Research Institute of Western Australia (MERIWA) Projects M349 and M349A sponsored by WASM, the Western Australian State Government and the mining industry. These projects have resulted in the construction and commissioning of the WASM Dynamic Test Facility and a program of reinforcement system testing. The primary purpose of the WASM projects is to evaluate the performance of complete reinforcement systems when subjected to an axial dynamic load. The test procedure, monitoring and associated analysis enable assessments for each component (ie the element, the internal fixing mechanism and the surface hardware) of the reinforcement system. The performance of a reinforcement system is usually defined by a static force-displacement response to axial loading. However, this static response may not be applicable to dynamic loadings associated with violent failure of rock due to overstressing as mines progress to greater depths. It was therefore appropriate that the responses of reinforcement systems subjected to dynamic loading be defined and evaluated. The key findings from the tests on a number of reinforcement systems are presented and recommendations made regarding their application for dynamic loading.

Jan 1, 2008

By M Manefield, G Bournival, S Ata

Asteroids contain an abundance of valuable resources such as: nickel, cobalt, gold, platinum and rhodium. Whilst the consumption of mineral resources on Earth continues to deplete, meteoroids have the potential to become a significant source of minerals. Even though the minerals content of asteroids may be relatively high, the valuable minerals are more likely to be only a small portion of the total ore present in the main body. The ores must, therefore, be processed to extract the metals of interest from the waste. Existing terrestrial technologies rely on manipulating the physical and chemical properties of minerals. The application of these techniques to asteroids processing, however, is not straightforward due to the presence of different conditions such as zero gravity and lack of water in space. This paper discusses potential separation and extraction techniques that can be used for processing of asteroids.CITATION:Ata, S, Bournival, G and Manefield, M, 2015. Resource recovery in space, in Proceedings Third International Future Mining Conference, pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M Mee, R L. Gwyther

Accurate measurement of rock mass response during the mining of massive underground orebodies is essential, as mines become larger and deeper. These measurements enable: provision of quantitative data for optimal pit slope design and engineering; monitoring of the stability of deep pit slopes, the long-term integrity of shafts and large-scale underground infrastructure, and long-term measurements of deformation or rock mass creep following the mining process for environmental management. Strainmeters traditionally used for deformation measurement have neither the long-term stability nor the high sensitivity to perform measurements in these applications. This paper describes a new precision borehole strain monitoring system (GTS) currently deployed by CSIRO Exploration and Mining, which has the potential to solve these new issues in rock mass deformation monitoring. This technology was originally developed for use in hard rock mines (Gladwin, 1977) and refined considerably for earthquake research (Gladwin et al, 1994; Gwyther et al, 1992). A case study of the use of the GTS in monitoring longwall coal mining over the period 1993 - 1998 is presented.

Jan 1, 2000

By A Valero, G M. Mudd

There is active debate and research around the most suitable indicators to assess the sustainability of mining. The most common approach is to report a range of data for a given mine site (or less preferably, a company total), such as inputs, outputs, benefits and potential costs. The most popular protocol in use (and growing rapidly) is the Global Reporting Initiative (GRI). However, these measures are numerous and still do not allow a single over-arching indicator to be developed. Other measures, such as known mineral resources over time, do not account for critical challenges such as declining ore grades, increasing wastes and poorer quality ores or more difficult mineralogy. By adopting a thermodynamic approach to sustainability, through the concept of æexergyÆ, it is possible to incorporate into a single measure the effective quality of mineral resources. Exergy involves the assessment of the minimum energy costs involved in producing a mineral resource with a specific chemical composition and concentration from common materials in the environment. The exergy of a mineral resource is evaluated from mineralogic composition, concentration (or ore grade) and, of course, quantity, by multiplying the unit exergies with the tonnes of the resource produced (or consumed). Since exergy is a thermodynamic quantity (ie energy or joules), it is additive across different minerals, such as iron ore to gold to copper or even oil and gas or coal û making it an ideal indicator to assess mineral resource sustainability at the industry scale rather than the individual mine scale. This paper briefly outlines the theoretical basis for exergy, and then presents a range of commodity case studies showing the application of exergy to the Australian mining industry. Overall, the usefulness of exergy is clearly demonstrated for use as a broad indicator of the sustainability of mineral resources at the national or even global scale.

Jan 1, 2009

By Bodnaras G. E, Sceresini P. A

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentration and high pressure to achieve extremely rapid gold dissolution rates. This is made possible by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device. The outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to-date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of 150 dry tonnes per hour at 40 - 45 per cent solids. Service life at this throughput is at least three months. The process may further be applied to high temperature leaching of refractory gold ores or other metals. Wear resistant metal or ceramic materials would be employed for this duty. Four mines are currently employing the Filblast Process for treating a variety of ore types ranging from highly reactive, almost impossible to treat, pyrrhotite/arsenopyrite to deeply weathered clay ore which forms a highly viscous pulp. The effect of shear thinning has resulted in improved adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately four million. Operating costs which include leasing and maintenance charges for the Filblast and pump power costs are about 16 cents per tonne. This is equivalent to about ten per cent of savings. Laboratory scale units having capacities up to 30 litres/min are available for test work but laboratory testing techniques so far developed do not accurately reflect the oxygen and cyanide savings which have been achieved in the plant.

Jan 1, 1994

By C Smith, R I. Maczkowiack, P D. Erskine

Open cut coal-mining has been conducted in the Bowen Basin region of central Queensland for almost five decades, and has disturbed an estimated area of 140 000 ha of agricultural land until 2011. Approximately one-third of the area disturbed by mining has been rehabilitated to pastures or bushland. However, none of the rehabilitated land has yet been assigned a specific end-use. This research project develops an approach for assessing end-use risks for the regionÆs mined land, and develops risk assessment models for selected end-uses. First, a web-based survey of stakeholders was used to identify risks to be assessed. The risks identified were surface erosion, subsurface erosion, bushfires, weeds and feral animals. The survey also identified possible end-uses of bushland and grazing. Second, conceptual risk models were developed based on the risk assessment concepts of likelihood and consequence specified in the Australian and New Zealand risk assessment standards. Likelihood was modelled using site characteristics and management factors that influence the occurrence probability of risks (eg surface erosion), while consequence was modelled using a set of site condition indicators and condition thresholds (changes in root-zone water-holding capacity, soil erodibility, vegetation ground cover and soil organic matter and transition probability to a non-preferred ecosystem type).The factors influencing likelihood and consequence for each risk have been integrated using Bayesian networks. The next step in model development is to parameterise the Bayesian networks using existing equations, empirical datasets, or expert opinion where data are not available. The parameterised models will be used to assess grazing and bushland end-uses against erosion, bushfire, weed and feral animal risks for rehabilitated mined land sites, with the purpose of identifying the relative risks associated with each end-use, and the landform design specifications and land management practices under which end-use risks are minimised.CITATION:Maczkowiack, R I, Smith, C and Erskine, P D, 2012. Risk assessment models for post-mining land use, in Proceedings Life-of-Mine 2012, pp 33-42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By S Wangchai, D B. Hastie, P W. Wypych, A P. Grima

Industries that handle and process ‘dusty’ ores are facing increasingly difficult challenges to ensure sustainable operation and development. Most existing dust-control measures treat only the symptoms of dust generation and do not deal with the root cause/s of the problem. Many of these methods are also relatively inefficient in terms of controlling dust emissions. This paper summarises the various existing options available for dust control and some of their features, advantages and disadvantages. It then describes some of the new technologies that are being researched, developed and employed to minimise dust emissions by addressing dustability or dustiness and the dust generation mechanisms found in industry. Recent research results and case studies are presented to demonstrate some interesting findings obtained from this work. With improved understanding and modelling of dust generation mechanisms and bulk material dustiness, it is possible to achieve a step-change improvement in the design, troubleshooting and application of more efficient dust-control technologies.CITATION:Wypych, P W, Hastie, D B, Wangchai, S and Grima, A P, 2015. Research and application of new dust control technologies for the iron ore industry, in Proceedings Iron Ore 2015, pp 529–536 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The first grant of land rights in Australia was pursuant to the Aboriginal Land Rights (Northern Territory) Act 1976. That Act has been at the core of the dispute between land rights and miners' rights. The mining industry believes that the Act, in giving a right of veto to Aborigines with respect to exploration and mining on Aboriginal land, has been responsible for a stagnation in exploration amd mining activity in the Northern Territory. In February 1985 the Commonwealth Government released for public comment its preferred model for national land rights legislation. The model has been opposed by the mining industry because it believes, first, that land rights is a matter which should be left to the States and, secondly, that the detailed mechanisms contained in the model constrain the industry in the manner of the Northern Territory legislation. Aboriginal leaders have opposed the model because it does not, in their view, measure up to undertakings given by the Commonwealth Government and, in addition, it provides for amendments to the Northern Territory legislation which are likely to result in the loss of the Aboriginal veto right. Are land rights and miner's rights compatible? The answer is yes provided all parties, including Governments, are prepared to talk and compromise and Governments recognise that the grant of land rights and any control by the Aboriginal people of exploration and mining on their land is not a substitute for raising the living standards of Aborigines as a significant group of disadvantaged Australians.

Jan 1, 1986

By G S. Esterhuizen, M M. Murphy, T S. Bajpayee

The strength reduction method (SRM) has been implemented in the FLAC3D finite difference software and applied to coalmine entry support evaluations. The FLAC3D numerical models have been calibrated against instrumented field sites in varying geologies, depths and field stress conditions. The calibration between the field and model results obtained a satisfactory match for rock deformation and support response. Previous research has also developed good correlations between numerical model stability estimations using the SRM and empirically derived stability estimations using the analysis of roof bolt systems (ARBS) software and the coalmine roof rating (CMRR). The purpose of this paper is to further apply the SRM to investigate how specific geotechnical and support parameters can impact coalmine entry stability. Results from different studies demonstrate how the calibrated models were used to investigate a few of the well-known questions in both mine design and support design. For mine design the impact of strong and weak beds in the roof strata, rotating the principal stresses and weakening the floor on excavation stability is investigated. For support design the impact of support length, support spacing and adding cable bolts to the design is demonstrated. These scenarios are evaluated in developmental coalmine entries for a variety of geology and field stress conditions. Stability factors are calculated for each scenario using the SRM. The SRM allows the impact of each parameter to be quantified and allows the support system to be optimised for given geotechnical conditions.CITATION:Esterhuizen, G S, Murphy, M M and Bajpayee, T S, 2014. Analysis of geotechnical and support parameters on coalmine entry stability using the strength reduction method, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 383–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Tien, J Huang, N Haque, M O’Brien

Coal preparation is an integral part of producing coal for thermal powerplants and metallurgical processing plants. Coal processing plants use various unit processes to separate gangue and ash content from mineral coal, thus increasing the specific energy content.A flow sheet and a simulation model was established for a typical coal processing plant using Microsoft Excel. This model used the mass balance and split factors for run-of-mine (ROM) coal, tailings and water usage from a typical, generic coalmine.The common method of coal preparation initially involves several stages of crushing to reduce the size of coal. It is then sent to the processing plant for further washing. The typical method in Australia for coarse coal material processing is the use of dense medium cyclone (DMC) (Kininmonth and Baafi, 2009). Flotation cells are used for processing of fine coal. The fine products are utilised for coking coal only. In our case study, the intended coal product is for thermal powerplants. Therefore, the fine coal processing utilised spirals instead of flotation, which is typical for the industry.CITATION:Huang, J, Haque, N, O'Brien, M, O'Brien G and Tien, J, 2016. Development, simulation, economic and environmental evaluation of a coal processing flow sheet, in Proceedings Life-of-Mine 2016 Conference , pp 48–51 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By M J. Newton

As part of the AMIRA P843 project Keeney and Walters (2008) describe how the principal components analysis (PCA) method can be used to identify classes of samples with similar metallurgical characteristics. However PCA does not take account of the location of each sample in 3D space. This paper describes a study to analyse the spatial distributions of the classes and determine appropriate modelling methods to control the estimation of the comminution parameters and mill performance indices into a 3D block model. This includes but is not restricted to geostatistical techniques that are used for grade modelling. The starting point for the study is the class definitions and the regression models for estimating the comminution parameters and performance indices. Each sample is assigned a class and the spatial distribution of each class has been analysed using different techniques including the calculation of variograms. This establishes whether the classes can be used as domain control for estimation into the block model – a procedure similar to using geological rock type domains for controlling the estimation of grades for a resource model. However, standard geostatistical estimation methods such as ordinary kriging assume that the variable being estimated is additive or linear. This assumption is valid for variables such as grade but this is not necessarily the case for the comminution parameters or the performance indices. Therefore the estimation procedure must either use variables that are definitely additive or the effect of potential non-additivity must be tested and accounted for where possible.The results of the study show how performance indices such as recovery, throughput and specific power can be estimated into the block model. This model is then combined with the geological model to provide a multi-parametric model that is used to optimise the mine planning and scheduling activities which can lead to significant improvements in NPV.

Sep 5, 2011

By M D. Sussman

A large number of countries in the world now have some regulation for labelling the presence of genetically modified organisms (GMO) in food. For the last ten years, ISO/TC 34/SC 16 has been providing methods, guidelines and requirements concerning the evaluation of molecular biomarkers including GMOs. This activity makes sure that stakeholders on all sides of commercial transactions are satisfied and their marketing or regulatory needs are met. Developing and maintaining a transparent, science-based environment for users of horizontal methods for molecular biomarker analysis is a high priority. Sampling and analysis of molecular biomarkers has become critically important for food and agricultural organisations developing, producing, distributing and selling genetically engineered, non-genetically engineered, identity preserved and/or organic crops and their derived products and preventing their respective destructive diseases. To aid in international harmonisation, a new work item proposal to develop an ISO type A management system standard (MSS) for organisations including laboratories using molecular biomarker analysis and sampling has been submitted to ISO/TC 34/SC 16. The purpose of this MSS is ensuring that determination of the presence, absence or quantification of a particular biomarker with a relationship to a product quality determinant, a marketing claim, a regulation or a plant pathogen is carried out under a suitable quality assurance / quality control system. This MSS will provide an overarching system to apply and manage molecular biomarker analysis and sampling for any organisation large, medium or small in a private, government or academic setting.CITATION:Sussman, M D, 2017. ISO/TC 34/SC 16 horizontal methods for molecular biomarker analysis – molecular biomarker analysis and sampling management system, in Proceedings Eighth World Conference on Sampling and Blending , pp 295–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By M John

The Kwinana Industrial Area (KIA) is by far the largest and most diverse industrial processing region (with supporting industries) in Western Australia. As with elsewhere in Australia (and globally), the KIA is facing sustainability challenges on various fronts, such as increasing water and energy scarcity, climate change, an aging workforce, and growing community expectations. Through the Kwinana Industries Council (KIC) the industries within Kwinana are working closely on common issues in the KIA, including the sustainable development of the region. Over the past decade, significant progress has been made by the industries towards the improvement of the sustainability performance at the company and regional level. Given the ever increasing sustainability pressures, there is strong desire to address sustainability challenges in the KIA, through a pro-active and collaborative industry approach. A sustainability roadmap is being developed to assist the KIC and its industry members with strategic decision making on the long-term sustainability of there. At the heart of the roadmap is a set of key performance indicators for each of seven priority themes or focus areas (water use, by-products produced, greenhouse gas emissions and energy use, economic performance, environment, community impacts and sustainable workforce). Aspirational targets and subsequent strategies are being developed for those activities where the KIC has an influence and can make a positive impact. The indicators and their targets enable constructive stakeholder discussions (eg with government and community) on emerging local issues and possible future directions for the KIA. The paper will report on the development process and the preliminary results of the sustainability roadmap for the KIA, including a historical perspective on milestones achieved so far and future aspirations.

Jan 1, 2009

By R Moreby, J Kok, L van den Berg

The high production rates achieved from mass mining methods such as block caving, sublevel caving and longwall mining require large conveyor belts, trucking loops (diesel/electrical) and rail systems for ore handling. However, the ore handling systems used in mass mines introduce a significant amount of heat into the overall ventilation system, which may be problematic at depth or in mines located in hot climates.In particular, the heat load from a conveyor system is not always well understood and consists of various components, including frictional heat from idlers, heat from electrical motors, heat from the drive train and heat from broken rock transported on the conveyor system. This paper presents results from a study that investigated the heat introduced to the ventilation air from a large conveyor system. The conveyor system transports ore with a maximum virgin rock temperature of 41°C from a depth of over 1 km. Air, belt and rock temperatures were measured in the conveyor system to evaluate the distribution of heat loads.CITATION:van den Berg, L, Moreby, R and Kok, J, 2015. Heat load estimation from conveyor systems in mass mines, in Proceedings The Australian Mine Ventilation Conference, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A R. McKinnon

The recently opened Hera Au-Pb-Zn-Ag mine in central New South Wales has provided an ideal opportunity to demonstrate the calculation of sulfide ore mineralogy using normative methods. Normative mineralogy applies a set of sequential rules based on the species likely to be present to assign the chemical components of a sample to their respective mineral components. The dominant sulfide mineral assemblage present at Hera is galena, iron-bearing sphalerite, chalcopyrite, pyrrhotite and pyrite. A normative technique for estimating the relative abundance of each of these species from drill hole, grade control and metallurgical assay data sets has been developed. This includes a process for deriving a gangue iron value and differentiating pyrrhotite from pyrite using sulfur/iron ratios. A calculated total sulfide volume value has been utilised at the mine to improve interpretation of lode boundaries. Normative drill hole values have also been used for domaining within the orebody, with large scale mineralogical trends evident. Dry bulk density (BD) values calculated using a normative species-weighted method show good correlation with measured BD values (R2 = 0.895) and are a significant improvement on the Pb+Zn+Cu regression method (R2 = 0.646) previously used. Application of these calculations to identify errors in assay databases is demonstrated, with specific reference to the data set for the nearby Nymagee copper deposit. Validation of block model grades is also explored and a method to improve resource estimates using direct normative mineral interpolation is proposed. The integration of the normative data into the production and metallurgical data sets at Hera is described and the relationship of the normative minerals to other economic elements such as gold and silver is discussed.CITATION:McKinnon, A R, 2017. Application of normative ore mineralogy to geological and metallurgical data sets at the Hera Au-Pb-Zn-Ag mine, New South Wales, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 63–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By A D. Pradana, D R. Pradana, Y H. Putra, Z Zulhan, T Hidayat

The high temperature processing of nickel laterite ore is currently dominated by the Rotary Kiln- Electric Furnace (RKEF) technology. The ratio of SiO2/MgO (S/M) in the ore is one of the critical parameters that determines the success of the RKEF process. Incompatible S/M ratios in the ore can cause aggressive chemical interaction between the slag and MgO refractory. The slag-refractory interaction at conditions relevant to nickel laterite ore smelting was investigated in the present study. Synthetic mixtures representing the slag compositions of nickel laterite ore smelting were prepared by mixing MgO, SiO2, Al2O3, CaO, Fe2O3, and Fe and heating the mixtures in steel containers at 1300°C under an argon atmosphere for 3 hrs. Pure MgO crucible were used as containment material in the melting process of the mixtures to represent the MgO refractory. The kinetics of the slagrefractory reaction were investigated using samples with selected initial S/M ratios of 2.0 and 3.0 (wt/wt) (with constant CaO = 3 wt per cent, Al2O3 = 5 wt per cent, FeO = 10 wt per cent) by performing melting at 1500°C in MgO crucibles for 5, 30, and 120 mins under an argon atmosphere. The effect of the S/M ratio in slag on the slag-refractory interaction was also investigated by performing melting of mixtures with different initial S/M ratios of 1.75, 2.0, 2.5, and 3.0 (wt/wt) in MgO crucibles at 1500°C for 120 mins under an argon atmosphere. After the melting process, each sample was quenched in water, mounted in resin, ground, polished, and coated. The interaction between the slags and MgO refractory was then evaluated by analysing the polished samples using a scanning electron microscope equipped with an energy dispersive spectroscopy (SEM-EDS). Thermodynamic simulations using FactSage™ 8.0 thermochemical software were performed based on the experimental slag compositions, refractory, and conditions to support the evaluation process. The results show that a higher S/M ratio in slag leads to a higher tendency for the refractory component to dissolve into the slag. A higher S/M ratio in slag also leads to an increasing extent of solid-state diffusion of iron oxide into the remaining refractory grains. The dissolution of MgO into the slag is rapid; the MgO concentration in the final slag increased by 2.4 wt per cent and 5.7 wt per cent at initial S/M ratios of 2.0 and 3.0 wt/wt, respectively, within 5 and 30 mins of the melting process.

Aug 21, 2024

By Seymour C. A

Peak Downs Mine, a five million tonnes a year coking coal operation, strip mines a, series of Permian coal seams. Seam thickness ranges from 0.5m to 5.0m, and seams consist of multiple coal plies with intermediate shale and mudstone partings. Four 47m3 draglines strip overburden to a cover depth of up to 60m. Coal loading is by 12m3 shovels and 14m3 to 18m3 front-end loaders. Parting removal takes place where the layer of shale and mudstone between seams exceeds 0.3m in thickness. Parting has been removed by a wide variety of earthmoving equipment in order to evaluate the problem and to select the optimum method from an operational and economic standpoint. Multi-seam stripping of the thicker seams is accomplished by working draglines from spoil- pile benches. Coal seams thinner than lm are recovered by dragline and stacked in the pit for later loading.

Jan 1, 1974

By D J. Bradshaw, B Lottermoser, A Parbhakar-Fox

"Best practice for acid rock drainage (ARD) risk assessment still relies solely on the geochemical properties of sulfidic rocks and mineral processing products, despite the fact that a rockÆs tendency to produce acid also depends on mineralogy and texture. Consequently, there are a plethora of geochemical tests routinely utilised by the mining industry to predict ARD formation. Due to limitations associated with these tests and their relatively high costs, analysis of recommended best practice sample numbers is rarely achieved, reducing the accuracy of waste management plans. Our research addressed this through examining the application of geometallurgical data for predicting acid formation, and led to the identification of potential environmental geometallurgy indicators.Samples obtained from an iron-oxide copper gold deposit were subjected to the geochemistry-mineralogy-texture (GMT) approach, an improved methodology for classifying acid forming potential. GMT results were compared against geometallurgical and assay data sets to evaluate: relative carbonate content measurements (measured by HyLogger) and identify how these could be used to calculate effective acid neutralising capacity mineral hardness (measured by EQUOtip) to determine application of this data for calculating lag-time to acid formation opportunities to automate the acid rock drainage index (ARDI) using classified images produced by a GEOTEK logger and automated microscopy.Links between the GMT approach and geometallurgical data sets were identified. Classified mineralogy data has application at stage one, HyLogger and EQUOtip at stage two and computer-based ARDI evaluations of classified images at stage three. Through such integration, ARD characterisation costs can be reduced, with value added to geometallurgical data sets. Furthermore, deposit-wide ARD domaining is possible, and acquisition of total-orebody knowledge more likely. Through adoption of this environmental geometallurgy approach, a better informed waste management plan can be formulated, allowing for best practice ARD sampling in a more cost-effective manner.CITATION:Parbhakar-Fox, A, Lottermoser, B and Bradshaw, D J, 2013. Cost-effective means for identifying acid rock drainage risks - integration of the geochemistry-mineralogy-texture approach and geometallurgical techniques, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 143-154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013