Search Documents

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The recovery and concentration of ultra-fine iron ore can provide significant economic benefits. Presently, there are limited options available given the low settling rates achieved by conventional gravity separation and the relatively poor performance of reverse flotation. The Reflux Classifier is a new water-based gravity separation technology that consists of a set of parallel inclined channels positioned above a vertical fluidised section. This arrangement promotes a powerful throughput advantage compared to conventional fluidisation and a highly selective hydrodynamic basis for achieving sharp separations. A high shear rate develops within the inclined channels, which generates sufficient hydrodynamic lift to convey the lower-density particles (even if they are relatively coarse) to overflow while retaining the high-density particles (even those that are ultra-fine) for discharge to the underflow. The technology has previously been used around the world on particle sizes in excess of 0.1 mm. The present work, however, is concerned with density-based separations down to much finer particle sizes approaching 0.01 mm.A major advantage of the Reflux Classifier technology is the achievement of simultaneous gravity separation and desliming via a single-stage separation. A series of continuous experiments was conducted using an iron ore feed with head grade of 35 wt per cent FeT and nominal top size of 0.106 mm, with 59 wt per cent being below 0.038 mm in size. At a low throughput of 1.5 t/(m2 h), the Reflux Classifier produced high-grade products at a high recovery. For the entire feed, grades of 66.1 wt per cent FeT with Fe recoveries of 80 per cent were achieved in a single-stage separation. Within the 0.020–0.038 mm size fraction, grades of 68.8 per cent were achieved with iron recoveries of 94.7 per cent. Excellent recoveries of up to 57.0 per cent were achieved for the -0.020 mm size fraction. The ability of the inclined channels to retain the fine dense material further enhances the effectiveness of the Reflux Classifier by creating an autogenous dense medium effect within the vertical section. This helps to elevate large gangue particles up into the overflow.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2015. Gravity separation of ultra-fine iron ore in the reflux classifier, in Proceedings Iron Ore 2015, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A Woodley, G Keir

The mining industry faces concurrent pressures of reducing water use, energy consumption and greenhouse gas (GHG) emissions in coming years. However, the interactions between water and energy use, as well as GHG emissions have largely been neglected in modelling studies to date. In addition, investigations tend to focus on the unit operation scale, with little consideration of whole-of-site or regional scale effects.This paper presents an application of a hierarchical systems model (HSM) developed to represent water, energy and GHG emissions fluxes at scales ranging from the unit operation, to the site level, to the regional level. The model allows for the linkages between water use, energy use and GHG emissions to be examined in a flexible and intuitive way, so that mine sites can predict energy and emissions impacts of water use reduction schemes and vice versa. This paper examines whether this approach can also be applied to the regional scale with multiple mine sites.The model is used to conduct a case study of several coal mines in the Bowen Basin, Australia, to compare the utility of centralised and decentralised mine water treatment schemes. The case study takes into account geographical factors (such as water pumping distances and elevations), economic factors (such as capital and operating cost curves for desalination treatment plants) and regional factors (such as regionally varying climates and associated variance in mine water volumes and quality).The case study results indicate that treatment of saline mine water incurs a trade-off between water and energy use in all cases. However, significant cost differences between centralised and decentralised schemes can be observed in a simple economic analysis. Further research will examine the possibility for deriving model up-scaling algorithms to reduce computational requirements.CITATION:Keir, G and Woodley, A, 2013. Regional trade-offs between mine water and energy use - a water treatment case study, in Proceedings Water in Mining 2013 , pp 21-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By D Lalor, N Goodman

The increasing demand for batteries is resulting in the development of large-scale projects for the production of key battery metals such as nickel and vanadium. Several of these projects plan to extract the battery metals from the ore via chemical roasting, leaving large volumes of waste iron oxides after fuming and/or leaching of the battery metals. These iron oxide wastes can be smelted in a HIsmelt furnace using biochar as the reductant, to produce clean, green pig iron with net zero carbon emissions. This green pig iron can then be added to basic oxygen or electric arc steelmaking furnaces to produce green, net zero carbon, steel. This paper describes the flow sheets and the economics for potential projects producing green pig iron via HIsmelt using waste iron oxides from nickel and vanadium production plants.

Sep 18, 2023

By N Kawashima, R St C Smart, A M. Robertson

This paper focuses on a case study at a base metal mine located in a tropical semi-arid area of Western Australia (WA). It is demonstrated that understanding the geochemical nature of the mine tailings forms an integral part of innovative management strategies developed throughout the life-of-mine (LOM) when planning for mine closure. The tailings are currently stored at an above-ground valley fill tailings storage facility (TSF) and one option for long-term management under consideration is leaving the tailings in situ at mine closure and covering using the concept of an enhanced æstore and releaseÆ cover system.Extensive geochemical and mineralogical studies have found that the geochemical behaviour of the tailings in the TSF is significantly more benign than initially predicted. The sulfide content of the tailings is primarily pyrrhotite, which can be acid-forming, acid-neutral or acid-consuming depending on a number of factors including redox conditions. Tailings pore water at depth is pH neutral with excess alkalinity, low concentrations of dissolved metals and elevated sulfate concentration.Recent geochemical tests on tailings samples indicate that a reduction in the acid potential and a corresponding increase in the neutralising potential of the tailings, through partial removal of pyrrhotite at the ore processing stage, has the potential to further reduce the long-term risk of potential impact to the environment from any TSF seepage. The current work program investigates whether partial removal of pyrrhotite is feasible and secondly, whether this approach is necessary to produce a significantly better outcome at mine closure.CITATION:Robertson, A M, Kawashima, N, Smart, R St C and Schumann, R, 2012. Understanding tailings geochemistry - Continuous learning and innovation when planning for mine closure, in Proceedings Life-of-Mine 2012 , pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By A D. Campbell, G R. Power

The increasing availability of marker data in sublevel caving operations is changing the way draw can be managed to achieve positive recovery outcomes in these mines. This paper describes how marker data has been incorporated into flow simulations to help calibrate full mine ore recovery simulations for the forecasting and optimisation of recovery.Some flow modelling techniques do not use marker data, relying instead on the outcomes of physical and numerical experiments to guide assumptions about an idealised recovery flow shape. Other mines have access to marker trial data, but find it difficult to specifically link this marker trial information to their recovery models. This can make it difficult to create a link between the marker trial information and recovery forecasting and limits the potential value of the marker trials at the mine.In the simulations shown here, the marker rings are fully incorporated into the flow model, and can be tracked in the model. The model is compared against the real underground marker recovery information to give the user an indication of how accurately the flow settings in the model are reflecting the conditions in the experimental marker rings. An example of use of this system at an operational mine is included.CITATION:Power, G R and Campbell, A D, 2016. Modelling of real-time marker data to improve operational recovery in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J Lyons, M Hasan, D Pepper, C Vadeikis

Processing of large volumes of ultrafine ores has long challenged mineral processing operators because of lower recoveries and increased tailings. This has led to many deposits, or parts of existing deposits, being viewed as uneconomic. As the mining industry can no longer afford to overlook resources that require finer sizes to achieve liberation or result in high tailings losses, the need for technologies to address these issues has increased. Mineral Technologies (MT) worked with a prominent Australian iron ore producer over five years to implement an innovative gravity separation technology for the beneficiation of ultrafine magnetite. The magnetite mineralisation requires a liberation size of <40 μm and selective rejection of ultrafine silica prior to magnetic separation. Through collaboration with the client, MT applied their Lyons Feed Control Unit (LFCU) technology for the beneficiation of finely grained magnetite. LFCUs are widely used in the mineral sands and iron ore gravity plants, and in tailings applications, to recover water and provide constant high density process streams. This project was an extension of knowledge gained from these applications. Test work was conducted on-site, using 1 t/h pilot and 300 kg/hr laboratory scale units. This test work showed that the LFCUs could reject 20 per cent of feed mass to tails whilst recovering >94 per cent of Fe to product. This upgraded the feed from 53.7 per cent Fe and 19.7 per cent SiO2 to 63.8 per cent Fe and 8.8 per cent SiO2. Recovery by size data showed a minimum 88 per cent Fe recovery to product for <8 μm material and up to 98 per cent Fe recovery for the -38+25 μm fraction. The LFCU rejected 70 per cent of <25 μm SiO2. The information obtained from the test work was utilised in the design of the full-scale units which are due for installation at the project site in 2021. This paper outlines the results of this laboratory and pilot scale test work and how the data obtained was used to design the full-sized units.

Nov 8, 2021

By P Holtham, W Valery, P Baguley, A Jankovic

There is a growing interest in magnetite ores because of the increasing demand for this commodity. With these ores, there is significant cost associated with milling the ore to fine sizes using ball mills in closed circuit with hydrocyclones. Cyclone classification efficiency tends to be poor due to the large difference in density between magnetite and gangue. This decreases the grinding circuit efficiency and results in over-grinding of magnetite. The objective of the work described in this paper was to modify the Bond locked cycle milling test procedure to quantify the loss of grinding circuit efficiency due to the mineral density effect. The locked cycle test procedure described here includes a stage of magnetic separation treating the closing screen undersize, which allows simulation of magnetite classification. The effect of classifier efficiency on low-density particles (non-magnetics) was simulated by altering the proportion of closing screen undersize bypass returning to the mill. Using a magnetic separator and a screen in the magnetics stream, different proportions of the magnetic fraction can be bypassed, thus allowing simulation of the effect of particle density on classification efficiency. This laboratory test work has confirmed that the impact of mineral density on cyclone efficiency subsequently has a crucial negative effect on ball mill circuit capacity. The results are in good agreement with reductions in capacity observed in practice. Multicomponent grinding and classification models were also developed in the LIMN software environment and were able to successfully simulate both the industrial and the laboratory ball mill circuit. The test and modelling procedures established in this project could be used for improved design of new magnetite ball mill grinding circuits as well as the optimisation of existing circuits.CITATION:Jankovic, A, Baguley, P, Valery, W and Holtham, P, 2015. Effect of mineral density for milling magnetite ores, in Proceedings Iron Ore 2015, pp 159–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By I Elias, E Moya, S Chaffer

This paper is based on a case study from a mine site that operates two gyratory primary crushers. These crushers were encountering problems, which included inconsistent P80, reduced liner life tonnage and, on some occasions, catastrophic failure of the liners.As part of an evaluation process, both crushers were ‘mapped’ using a technology for condition monitoring and modelling of the crusher’s wear components. The technology provides comprehensive coverage of the crusher’s concaves and mantle at 100 mm intervals. It also automatically assesses wear rate between inspections and determines the highest wear areas. Outcomes include projected optimum reline dates at target replacement thicknesses, the identification of asymmetrical wear patterns, and the accurate measurement of open and closed (OSS/CSS) side settings.A comprehensive study was performed to optimise the performance of both these crushers at site. Over a period of seven liner service lives, the strategies to improved performance included liner analysis (concaves and mantle profile analysis), tonnes per day (t/d) and tonnes per hour (t/h) analysis, mantle reutilisation, detection and control of loose concaves, and detection and control of uneven wear and hot spots.These strategies resulted in the improved mechanical and operational performance of both crushers through concave and mantle redesign, OSS/CSS control, accurate wear forecasting plus other initiatives.As a result of these initiatives, the site now experiences benefits which include consistent product size, increased tonnes per hour (t/h) for both crushers and the liner life tonnage has doubled. Additionally, further benefits include less downtime for crusher liner maintenance and the reduced cost of inventories by mantle reutilisation.CITATION:Elias, I, Chaffer, S and Moya, E, 2015. Improvements in service life and cost reduction for gyratory primary crushers through mantle and concaves optimisation – a case study, in Proceedings Iron Ore 2015, pp 115–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By H Ishikawa, S Palaniandy

The gravity-induced stirred mill such as the TowerMill is an energy-efficient grinding solution used in secondary, tertiary, and regrinding duties in the mineral processing concentrator. The interest in this technology is emerging, with more than 300 mills installed globally in various grinding duties and commodities for the last 30 years. Although the technology is matured, there are still opportunities for improvement and the development of new knowledge to improve its circuit energy efficiency and reduce water consumption. Recent studies show that a combination of stress intensity, ore hardness, slurry density, and mill feed configuration can be used to evaluate the performance of the grinding circuit. A recent pilot-scale TowerMill test work at various stress intensities shows that a lower operating work index and size-specific energy were achieved at higher agitator tip speed and using medium size grinding media. These outcomes were confirmed through several site trials. A smaller 17 mm grinding media has reduced the operating work index and size-specific energy by 18 per cent and 11 per cent, respectively, compared to the 20 mm in a magnetite concentrator. Moreover, the conversion from top feed to bottom feed configuration has reduced the operating work index and size-specific energy by 13 per cent and 37 per cent, respectively. The circulating load was reduced by 34–38 per cent, leading to a reduction in the dilution water consumption in the hydrocyclone feed sump by 20 per cent. A variable frequency drive offers flexibility to change the stress intensities on the TowerMill, where a 35 per cent reduction in specific energy was achieved when the ore became soft. This paper explores the potential design and operating strategies that can be implemented to enhance the energy efficiency, reduce water consumption and reduce CO2 emissions in the circuit and finally evaluate its impact on the total cost of ownership.

Aug 24, 2022

By S Bright, M J. Masamvu, E K. Chiwandika, S Dandi, S M. Masuka

The depletion of high-grade hard and lumpy chrome ores has forced Zimbabwean ferrochrome producers to resort to low-grade friable ores that have an average of 28 per cent fines against a set limit of 12 per cent. Submerged open arc furnaces currently in use are associated with eruptions within the furnace because of the high amounts of fines, high energy consumption, as well as high SO2 and CO2 emissions. Traditionally employed agglomeration methods such as pelletising and the use of coke in the furnace have been discarded because of the pressure to lower operational costs and to achieve higher profit margins. This research aims to develop a method to incorporate lowgrade friable ore fines and unprocessed coal into production while lowering CO2 and SO2 emissions through a closed direct current (DC) arc furnace. The closed DC arc furnace could incorporate the friable ores and coal while maintaining above 90 per cent reduction rates. Preliminary findings also show that energy consumption could be reduced by up to 35 per cent by incorporating a pre-heating and pre-reduction system using the flue gases from the furnace. In the proposed circuit, the cost of production per ton of ferrochrome might be potentially lowered by an average of 30 per cent.

Jun 19, 2024

By H R. Phillips

The ventilation and refrigeration design of underground mines is an important aspect, when new or existing mines are considered and places a great responsibility on engineers tasked to do so. The current trend for both local and international underground mines is to extend their search for valuable ore reserves deeper below surface. In South Africa, the predictions are that about 40 kt of actual gold still lies in situ, ready for extraction. As mines extend their search for minerals of economic value deeper and deeper into the earthÆs crust, ventilation and refrigeration aspects of such mines become more prominent than before. The planning and design of the required ventilation and refrigeration within these mines, over their expected lifetime is important including the practical implications of such designs. Technology changes and improvements need to be incorporated into ventilation and refrigeration designs, where possible and advances in this specialised field explored. This paper explores ventilation and refrigeration design aspects within the underground mine sphere. Aspects such as mining depth, virgin rock temperature (VRT), mining methods, and different cooling applications available including ventilation supply are reviewed in design applications. Heat generally becomes a significant aspect to counter in these mines and they are not always necessarily deep mines.

Jan 1, 2005

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

By R C. A Minnitt

The two methods for calibrating the parameters K and (alpha) for use in Gy’s equation for the fundamental sampling error (FSE), the duplicate sampling analysis (DSA) and the segregation fractionalised analysis (SFA) are described in detail. A case study using identical broken reef material from a Witwatersrand-type orebody is calibrated using the DSA and SFA methods and the results are compared. Classically, the form of Gy’s equation for the FSE raises the nominal size of fragments given by dN to a power of 3. Gy’s formula is a theoretical formula applicable in the case when fragments are randomly collected one by one, which is obviously never the case. This is because the fragment shape factor (f) and the granulometric factor (g) were introduced to take care of this anomaly. More recent formulae, such as those suggested by François-Bongarçon and Lyman, are empirically based formula. A later modification of Gy’s formula raises dN to the power ? (alpha), the latter term being calibrated with the coefficient K in the DSA and SFA methods. The preferred value of ? (alpha) for low-grade gold ores used by sampling practitioners in the mining industry is 1.5. A review of calibration experiments for low-grade gold ores using the DSA and SFA methods has produced values of K that vary between 70 and 170 and values of alpha in the range 0.97 to 1.30. The average value for alpha is found to be 1, rather than 3 as originally proposed in the classic form of Gy’s equation or the industry preference for 1.5. It is suggested that for low-grade gold bearing ores, the equation for the FSE should raise dN to a power of 1. Such an equation for the variance of the combined FSE plus the grouping and segregation error, now referred to as the short-term component of the quality fluctuation error (QFE1), greatly simplifies the characterisation of gold ores, which now only requires the calibration of K for a given mass and established fragment size. The implications for the heterogeneity test from the generalised equation are that provided the fragments have been screened to within a narrow size range, any particular size will return a value for K that is acceptable for use in the sampling nomogram.CITATION:Minnitt, R C A, 2017. A generalised form of Gy’s equation for gold ores – empirical evidence, in Proceedings Eighth World Conference on Sampling and Blending , pp 331–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Minerals processing operations use a significant quantity of fossil carbon to provide energy and as reductant. Greenhouse gas emissions from the use of this fossil carbon contribute to the global increase in anthropogenic CO2 emissions to the atmosphere. In the spirit of fostering thinking about a step change in this situation, this paper explores opportunities for the use of sustainable carbon from biomass sources in a range of mineral processing operations. The exploration shows that many common processes are contenders for fossil carbon replacement and that feasible scientific research by minerals processing technologists would add to deeper understanding of the potential for a sustainable bio-carbon based industry. It is also shown that there are many dilemmas on the social, environmental and economic fronts to be solved before a biomass based industry could become a reality.

Jan 1, 2004

By S Nkwanyana, I Govender

Batch experiments in a 0.6 m diameter mill have shown that improvements of about 13 per cent in the efficiency of energy utilisation can be realised in ball mills by replacing 25 per cent of the ball charge by an equivalent volume of cost-free critical size pebbles from AG/SAG mills. For a mill of a given size, speed and charge filling, the rate of size reduction of ore particles depends on (i) the frequency of grinding media collisions (ii) the probability of capture of ore particles between the colliding grinding media (iii) the probability of fracture of the captured particles. The probability of fracture depends on the magnitude of collision energy. The distribution of collision energy into shear and impact events determines the relative strengths of attrition breakage and impact breakage. The efficiency of energy utilisation depends on which of the two mechanisms of breakage is more desirable in a particular milling stage. In this paper collision data from a series of DEM simulations of a mill charged with steel media and a mixture of steel media and pebbles is presented in energy spectra and spatial distribution maps. The data provides the necessary detail to elucidate the improvements in the efficiency of energy utilisation in ball mills when using a mixture of pebbles and steel media.

Aug 24, 2022

The modern resource extraction enterprise is a complex capital intensive business operating in a world of constantly evolving social, environmental and economic scrutiny. Investors, government, media and special interest groups expect to see business environmental and social performance respond and deliver increasing corporate responsibility and sustainability. &nbsp; Thorough interrogation of business performance using a multi-disciplinary due diligence approach presents a more sophisticated review and benefits beyond the traditional compliance/conformance &apos;audit&apos; style assessment. &nbsp; Using a due diligence approach allows assessment through a comprehensive lens which examines potential short- and long-term risks including sometimes less tangible environmental and social liabilities, and informs management, investors and regulators of broader business performance. This approach provides information in a form that business can measure performance in a repeatable and enterprise wide sense. &nbsp; This paper provides an outline of the due diligence process applied in this way, drawing from lessons learnt and industry based experiences in the due diligence process and the benefits and tools that can&nbsp; be applied in an environmental and social due diligence business performance assessment

Jun 1, 2010

By S Smith

Several styles of copper (Cu) mineralisation are present at Sepon. Large tonnage, low grade skarn and carbonate replacement massive sulfide mineralisation occur within the metamorphic aureole of Permian-aged rhyodacite porphyry intrusions (RDPs). During exhumation and supergene weathering, this primary mineralisation has been upgraded to form high-grade chalcocite enriched zones up to 50 m thick, which comprises the bulk of Cu resources currently being mined at Sepon. Groundwaters remobilise Cu to form exotic accumulations of malachite that are locally hosted in irregular karsts in carbonate rocks, found up to 1000 m from source mineralisation. Khanong is the largest Cu deposit and recent discoveries have been made at Thengkham South, Thengkham North and Phabing. All deposits have formed by similar processes of mineralisation. However, all differ due to local variations in host rock lithology, structural setting, and hydrological conditions. An&nbsp;EXTENDED ABSTRACT&nbsp;is available for download. A full-length paper was not&nbsp;prepared for this presentation.

Jan 1, 2008

By I Grewal, M Lundt

Dense medium separation (DMS) is one of several preconcentration methods used for early waste rejection from run-of-mine ores at relatively coarse particle sizes prior to additional milling and beneficiation. DMS has been used extensively in the coal, diamonds, mineral sands, base metals and iron ore industries to produce either a final product or as a preconcentration step. Laboratory scale and pilot test work at the Met-Solve laboratory in Canada has demonstrated successful separation and upgrading of other minerals such as lead, zinc, copper and lithium based ores using DMS.This paper reviews historical dense media systems, results from the pilot-scale multi-stage DMS Separator “Condor” system, as well as production plants and associated laboratory heavy liquid separation (HLS) test work on various minerals. The mineral systems tested included a lithium bearing ore and a fluorspar ore. Other minerals were tested but are not reported in this paper.Pilot plant test work on a fluorspar ore showed that 41.6% of the mass could be rejected to the tailings stream while 95.3% of the CaF2 was recoverable to the product stream. On a spodumene sample that was tested, it was possible to reject 55% of the mass to tailings while recovering over 90% of the lithium.In recent market conditions and with the decreasing grades in existing ores, preconcentration should be a consideration to maximise the value of certain operations.CITATION:Lundt, M and Grewal, I, 2017. Dense media separation – a valuable process for preconcentration, in Proceedings MetPlant 2017, pp 122–130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By S Grant, S Emeric, P Baker, E Jones, D Clark

As we strive for a sustainable and resilient future, repurposing assets has become a top priority. In Australia alone, we have a significant number of mineral projects in the pipeline, extensive existing operations, and over 50 000 legacy sites. Collectively, this presents a unique opportunity to be a world leader in mine rehabilitation. Complex stakeholder landscapes, inflexible policies, aged regulatory frameworks, technical uncertainties and increasing liabilities are all barriers hindering effective transition of legacy assets. The impetus for change is further catalysed by shifting consumer preferences, workforces in flux and regional Australians questioning what the transition means for their local community. We need innovative approaches to take a leading role in the industry and support global efforts more broadly. Co-designing an ambitious, shared vision spanning projects, operations and legacy assets with all key parties is a fundamental step to unlock and realise maximum societal, environmental, economic and reputational value. Serious play and gamification can further enhance this visioning process.

Aug 2, 2023

By S R. Pecover

AustraliaÆs opal and sapphire mining industry has fallen from its peak in the 1980s and 1990s into a significant low today. This is not due to exhaustion of the resource, but instead an over-reliance of the Australian miner on achieving a fair price for the gemstone product from offshore middlemen dealers. Gemstone and geological research is also at a low as Federal higher education expenditure has fallen with research institutions relying increasingly on private funding in an environment of restricted autonomy and flexibility for researchers. What little remaining research skills the universities have is being bled into the private sector as a result of the mining boom and encouraged by lower than average academic salaries. Nevertheless, some highly innovative research has been taking place, often by self-funded individuals and retired academics simply with a desire to advance the understanding of the particular branch of science in which they are interested. New models for the formation of sapphire and opal are now beginning to be applied to the exploration for these gemstone commodities. This research, together with well thought out plans for managing the gemstone product through its value-adding steps to the jewellery retail level, has the potential to bring about a resurgence in the Australian gemstone industry.

Jan 1, 2008