Search Documents

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004

By A Golsby

Both primary and secondary ventilation is important in underground mining. Secondary ventilation refers to the provision of ventilation to development ends, stopes and services facilities, which constitute secondary circuits tapped off the primary circuit or main through flow of air.An unbalanced primary and secondary combination can cause re-circulation, which is inefficient and potentially hazardous. These inefficiencies extend into operational and other considerations, such as power.Most cost justification analysis covers capital and physical consumables. These analyses are often not comprehensive or holistic. This case study is an example of ‘how to holistically justify’ a secondary ventilation circuit and optimise it to meet all stakeholder needs.This paper particularly addresses the following:how to account for all stakeholders in a secondary ventilation cost justificationthe secondary ventilation componentsthe cost justification outcomes and how to measure themsome of the sensitivitiesthe stakeholdershow to present the justification to meet the stakeholder needssecondary ventilation cost justification.CITATION:Golsby, A, 2015. Secondary ventilation as a value proposition – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Optimising a mining or a quarrying operation about the overall cost is quite a challenge as there never is a situation where we have exactly the same conditions regarding rock properties, explosives' performance, mining equipment or evironmental restrictions. The amount of endless influencing parameters and variables make the evaluation process difficult. The enormous progress we have seen during the recent two decades in computing has however significantly increased our ability to evaluate and process the information gathered, and refine our existing prediction models. Refined models demand an increasing volume of good quality information to show reliable conformity with reality. There is a great need for co-operative work in the mining and quarrying society if we shall be able to screen all available data, systematically find the key-parameters influencing the results and to build robust scientific models. No organisations today have all the skilled people needed or can afford to hire the necessary specialists in all the overlapping branches. This paper highlights some on-going work where the Dyno Explosives Group is adding some new pieces to the giant jigsaw puzzle representing the ultimate model of the mining and quarrying operations we all of this society would like to see completed.

Jan 1, 1995

The operations management system at Olympic Dam has evolved over a two-year period to the state described in this paper. This evolution has been driven largely by the requirements of the recent expansion of the Olympic Dam operation from three to nine million tonnes of ore per year. Such a change process demands an holistic approach to mine management and several techniques have been employed including XPAC, Mine Works Planner as well as a basic philosophy of æjust-in-timeÆ completion. The philosophies, software and tracking mechanisms for managing a large tonnage operation are described, outlining a fully integrated scheduling system from shift to shift detailed activity planning to a 20 year production plan. Moreover, the vision of production exceeding the current limit of nine million tonnes means that there are to be further developments to this state-of-the-art system in use at the Olympic Dam mine.

Jan 1, 2000

By B Stump

Reliable particle size analysis in minerals processing plants is a critical factor to the economic return of a plant. As recovery of valuable minerals is compromised for particles outside the optimal size range, effective and reliable particle size analysis is more crucial than ever, particularly in the current upswing of the global commodities market. Inefficient particle size analysis can lead to excessive over-grinding, thereby significantly increasing energy consumption and reagent costs, whilst negatively affecting process operation, thickening capacity, water recovery and tailings disposal.Australia’s first installation of a particle size analyser in Iron Ore has been monitored with great interest by the industry. Previously, manual size sampling at Rio Tinto’s Paraburdoo fines processing plant involved off-site sample analysis, with a turnaround measured in days. The Outotec PSI® 500 particle size indicator, commissioned in July 2009, takes approximately three minutes per line at site.The paper will include details on the following:• plant description,• sampling design,• PSI® 500 analyser functionality description, and• key learnings from site.

Jul 11, 2011

By A Noack

Today underground infrastructures, like tunnels and especially wide spread underground mines, are often equipped with ethernet based communication systems. These networks are used for the unified communication of data, voice and video. As these networks stretch along the major tunnels and in increasing scale also into the production areas, a high degree of coverage can be reached. For wireless coverage, standard IEEE 802.11 WLAN access points are being used. In order to provide a maximum availability and reliability, the active components are equipped with battery backup power supplies and the network infrastructure is set up in a redundant way using ring or meshed topologies. This provides a much higher availability compared to traditional phone systems or dedicated data links using a conventional star topology.Distributed computing intelligence that is installed on active network nodes throughout the whole network, additionally supported by a central server system, creates the basis for new mine safety functions introduced in this paper for both coal and non-coal mining. These new safety functions cover the detection of potential emergencies, using the status of the network as a æsensorÆ, as well as dynamically guiding people to safe exits or rescue shelters in case of an emergency. Furthermore, these functions are of important benefit for improving the efficiency of search and rescue operations following a major incident or accident underground.

Sep 26, 2011

By S Tjerry, S Szylkarski, B Willis-Jones, I Dubinski

Achieving relinquishment of mining sites is becoming increasingly difficult, with a study by Byrne (2013) estimating that out of a set of 73 mining and metals sites around the world, less than ten per cent had achieved relinquishment over the last 50 years. The median forecast duration of time allocated for water management in the closure plans studied was approximately ten years, while the reality at the actual sites was a median duration of 22 years to date and growing.One of many challenges in mine closure planning is managing geomorphic stability of stream diversions. The challenge is to be able to demonstrate to regulators and the community that a proposed rehabilitation solution will be stable over the long term.During the mining operations, local watercourses and surface drainage can be diverted and managed using engineered channels and drainage structures. However, during the post-operations stage, the engineered channel and drainage may require modification to a more natural condition that will facilitate long-term environmental sustainability. Achieving geomorphic stability of a diverted watercourse is difficult, with the majority of stream diversions in Australia failing to meet expected design performance (White et al, 2013). Geomorphic stability is a complex process that is controlled by a combination of factors, including hydraulic flow conditions, geotechnical conditions and vegetation.This paper proposes that a fully dynamic and deterministic geomorphological model can be used to supplement the traditional empirical approaches to assess long-term geomorphic stability. The paper provides an overview of the geomorphological models and how they have been applied in engineering studies for forecasting future evolution of stream systems. The paper discusses the potential application of these models in the mining industry for forecasting and optimising surface water structures for the operations and post-operations stages of the mining cycle.CITATION:Szylkarski, S, Willis-Jones, B, Tjerry, S and Dubinski, I, 2016. Improving the reliability of stream diversion designs in mine closure plans using a morphological tool, in Proceedings Life-of-Mine 2016 Conference, pp 212–215 (The Australasian Institute of Mining and Metallurgy: Melbourne)

Jun 28, 2016

By M P. Schwarz

This paper describes modelling studies of the flotation cells used by BHP Billiton Nickel West Ltd in the slimes circuit at Mt Keith. The aim is to achieve a better understanding of the hydrodynamic limitations in the existing cells to improve nickel recovery. Computational fluid dynamics (CFD) simulations have been performed on the 100 m3 mechanically-stirred cells. The data produced by the simulations include velocity vectors, gas holdup distribution, solids distribution, bubble size, superficial gas velocity and turbulent parameters. These results have been checked and found to match hydrodynamic measurements at the plant. An analysis of the data found that one of the limitations in fine particle recovery was related to the air bubbles discharged with the tailing. The air in the discharge was caused by the high viscosity of the pulp. In the presence of fine particles, the pulp exhibits high viscosity with a yield stress. The increased drag due to high viscosity caused the bubbles to rise more slowly up the cell. This results in a significant hold-up of bubbles, some of which report to the tailing with associated loss of valuable minerals. A parametric CFD study of the operating variables shows that less air would be discharged in the tailing by decreasing the following: air flow rate,pulp density,stirring speed, andfrother addition. Simulation results indicate that these changes would cause a lowering of the air hold up in the cell especially near the discharge area. Predictions of the bubble-particle attachment rates under various operating conditions have also been calculated. Although it is possible to increase attachment rates by increasing stirring speed or by increasing pulp density, the amount of air discharged and the amount of nickel loss through the tailing will also increase. The project showed that CFD modelling is a powerful tool for studying hydrodynamic effects of bubble-particle interactions in flotation cells.

Jan 1, 2008

By J Szymanski, Y Hu

Excavation engineering involves complex processes for primary and secondary extraction of materials. The shovel excavators bear varying mechanical energy input and stress loading across the working bench during excavation. These varying mechanical energy input and stress loading effects cause significant wear and tear and fatigue failure in equipment components. These effects further result in unplanned downtimes, reduced efficiency and high production costs. In addition, the mechanical and electrical control systems must be operated in efficient profiles to generate maximum outputs and efficiency from these excavators. Efficient technologies are therefore required to solve these problems in order to reduce production costs and increase efficiency. In this paper, the authors develop a rigorous simulator for a hydraulic shovel in a surface mining environment. The finite element model is used to capture the stress profile within the shovel components during excavation, such as, the bucket, stick and boom assemblies. The profiles are classified into normal, critical and extreme ranges, with appropriate corrective measures to avoid extreme loading conditions. The loading capability of shovel excavators can be examined by assessing its structural strength against all possible maximum loads working on the equipment. The dynamic model is used to define efficient profiles of the critical structural components of hydraulic shovels during digging operation. This assessment is used to locate the maximum possible loads and the critical sections of the structures. The method presented in this paper forms the basis for developing comprehensive simulator models for efficient shovel operations in constrained mining environments.

Jan 1, 2003

By G L. Boyd

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal recovered by highwall mining methods.

Jan 1, 1998

The outlook for suppliers of energy to the expanding economies of the Pacific Basin region is essentially positive, but particularly for exporters of high quality steam coal. This paper argues that economic growth in the Pacific Basin region has exceeded world economic growth for some years and that this will continue to be the case for the next decade at least. It looks briefly at the link between economic growth and energy demand and at the relationship between energy demand and the demand for electricity. Changing preferences in fuel mix for electrical generation in the region are noted and tentative forecasts made about variations in this mix. The pros and cons of various forms of fuel used to generate electricity are considered from the point of view of the consumer. Having concluded that steaming coal in particular is likely to become even more important as a generator of base load electricity, the paper looks at the opportunities this presents for exporters such as Australia, and touches on some factors that could prevent development of those opportunities. This paper will concentrate on electrical energy. For the purposes of this paper, the Pacific Basin refers essentially to Australia, New Zealand and the Asian countries bordering the Western Pacific. As a supplier, Siberia is not included because, although it has great potential, it is thought that problems of climate, infrastructure and political restructuring will delay the realisation of that potential until the next century. Although it deals with the Pacific Basin region, where many countries are industrialising rapidly from a predominantly agricultural base, it looks at the experience of mature industrial DECD economies where their experiences seem relevant.

Jan 1, 1990

By A Sadri, S Smith

In the metal and mineral industry, different empirical techniques are used to estimate the remaining thickness of the lining within an operating furnace. The disadvantage and costly factor when using these methods is that production needs to be halted. Hatch has developed an accurate and reliable technique based on stress wave propagation principles to determine the condition of the remaining lining whilst the furnace remains online and operational.The technique involves test data collected and compiled to generate 3D imagery used to assist operators and maintenance planning personnel with valuable information showing areas of metal penetration in the lining, remaining lining thickness, exact location of voids, cracks, poor contacts and deterioration due to chemical attack. In this paper, the principals of the AU-E technique will be explained both theoretically and practically. In addition, the use of ultrasound technology for determining the condition of copper cooling elements will be briefly addressed.

Jan 1, 2006

The paper focuses on how rock bolts are loaded in different rock masses, as well as in pullout tests. Three analytical models for rock bolts are presented in brief, one for bolts in continuously deformed rock masses, one for bolts in blocky rock masses, and one for bolts in pullout tests. The bolt models are used to interpret measurement data for rock bolts from three sources and to help specify the modes of axial load in the rock bolts. It is found that in continuously deformed rock formations fully coupled rock bolts have only one axial stress peak. The position of the axial stress peak moves towards the far end of the bolts with increasing rock deformation. In blocky rock masses several axial stress peaks may appear in the rock bolt. The position of this kind of axial stress peak does not change during the entire loading process. For rock bolts in pullout tests, decoupling of the interface always occurs first at the loading point. The decoupling front moves towards the far end of the bolt with an increase in the applied pull load.

Jan 1, 2000

By A Hoyle, P Walker, D Bennett

The Phu Kham copper-gold operation located in Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited, based in Brisbane Australia, holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining 10 per cent held by the Government of Laos PDR.The 12Mt/y copper-gold concentrator at Phu Kham commenced production in April 2008. Flotation copper and gold recovery from commissioning was consistently poor, due to the high levels of pyrite and problematic secondary and oxide copper species and non-sulfide gangue.The low recoveries of copper and gold from Phu Kham were recognised during the feasibility study design phase. A bulk sulfide flotation regime in roughing produced high recoveries, however a large capacity cleaning circuit was required and there was risk of not meeting saleable concentrate grade specifications. The installed design offered a capital efficient compromise to ensure that a concentrate grade of 24% copper could be achieved at acceptable recoveries.Incremental improvements in copper recovery were achieved by 2011 through conversion of conditioning cells to flotation cells in both roughing and first cleaning and increased cleaner capacity through the installation of a Jameson cell. In 2012 the Phu Kham Upgrade Project was commissioned to increase mill throughput, along with additional rougher and cleaner capacity to increase residence times at the nominal 16 Mt/y throughput. The marginal reduction in primary grind size due to the additional ball milling power also provided a small recovery improvement.This paper presents the development, design, implementation, and performance of the Increased Recovery Project commissioned in April 2013 which targeted the major causes of copper loss from the circuit. Based on fundamental and detailed test work and mineralogical analysis of concentrator streams, an optimised design was developed which has increased copper and gold recoveries by over 5% and 10% respectively. The Increased Recovery Project has positioned the concentrator to process high pyrite ores that were previously considered untreatable, and opened further opportunities for maximising flotation recovery by de-bottlenecking plant regrind and cleaning capacity.CITATION:Hoyle, A, Bennett, D and Walker, P, 2015. The increased recovery project at the Phu Kham copper-gold operation, Laos PDR, in Proceedings MetPlant 2015, pp 246–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By D Suppel, Y Miezitis, S Jaireth

The competition between various options for the use of land is ever increasing. Commonly in Australia large tracts of land were un-encumbered by sweeping land use option limitations, but this situation has been rapidly altering in recent decades as governments are obliged to maximise the utility of the land for a broad range of competing interests. While the interests of miners have always been considered, the effects on limiting access to land for exploration and possible mining have not always been effectively incorporated into decision-making processes. As a result the challenge for national and state organisations representing these interests has been to develop a transparent process to allow for the mineral potential of an area to be systematically assessed and for information to be presented for use by specialists and non-specialists. Government agencies are called upon to implement government policy but also to provide accurate and meaningful advice which can assist in policy and land use decisions. Commonly timeframes are short and information can be less than complete. Nevertheless on-going decisions are made based upon the best available understanding. It is in this operational framework that the methods described in this paper are set. The paper describes a process for quickly and systematically providing advice on mineral potential for use by government agencies and ultimately the community within tight time and resource constraints. It is a method of combining the accumulated knowledge about mineral resources and their potential and presenting this information in an easily accessible form which can be used in a negotiation and policy development environment. Development of the method was undertaken to meet the needs of the Regional Forestry Agreement process in Australia. The method has been applied to study areas in New South Wales, Tasmania, Western Australia and elsewhere. Examples in this paper are taken from north eastern New South Wales.

Jan 1, 1999

By R Fanni, D Reid, M Kulessa

Recent updates to Australian industry guidelines emphasise the importance of the assessment of liquefaction potential of tailings. This includes assessment of the cyclic liquefaction potential, and the post-seismic strength of tailings expected to undergo strength loss from seismic loading. Despite this increase in focus, a relatively small number of Australian tailings appear to have been characterised through cyclic and post-cyclic testing. This paper presents the cyclic characterisation of four Australian tailings, consisting of iron ore, lateritic nickel, vanadium and bauxite residue. Material was obtained either from surficial tube sampling or through remoulding samples in the laboratory from slurries. Testing consisted of monotonic, cyclic and post-cyclic tests for each material. For three of the materials, laboratory-scale shear vane testing was also performed to provide a comparison to post-cyclic strengths from direct simple shear.The results indicated cyclic resistances consistent with the results of other tailings presented in the literature. The lateritic nickel tailings provided the greatest cyclic resistance of the four materials tested, followed by the vanadium tailings. This was somewhat consistent with expectations for material behaviour based on index properties. Post-cyclic strengths were seen to decrease as cyclic strains increased, consistent with typical observations in the literature. Following significant cyclic straining, in some instances the post-cyclic strengths approached those obtained through residual shear vane testing. This provides further insight into the strain-dependent nature of post-cyclic strengths for some materials. The implications of these observations on the post-seismic stability condition are discussed.CITATION:Reid, D, Fanni, R and Kulessa, M, 2015. Cyclic and post-cyclic behaviour of four Australian tailings, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By E Ben-Dor, D Bakun-Mazor, Y Ben-Ari

Determining the mechanical properties of rocks is important for various civil engineering fields, including the mining of raw materials for aggregates used in the construction and paving industries. Traditionally, the mechanical properties of rocks are obtained through in situ and laboratory tests during geotechnical surveys. However, these time-consuming surveys involve many resources. In contrast, hyperspectral remote sensing methods make it possible to identify the mineralogical composition and crystallographic structure of the rock; properties that control the mechanical properties of the rocks. In this work, we characterise the mechanical properties of carbonate rocks by using a hyperspectral sensor in laboratory conditions. We collected about 150 cylindrical samples of carbonate rock, with a wide range of strength values from several rock outcrops in Israel. We used a point spectrometer in the range of 0.4–2.5 μm and a spectral image sensor in the range of 3.0–12.0 μm, scanning the samples to obtain the signature of their light reflections and spectral emissivity. We then measured the samples’ density, porosity, water absorption, and uniaxial compressive strength (UCS). We used sophisticated data mining to find statistical relationships between the hyperspectral signatures of the samples and their mechanical properties. We used this data to identify the most dominant wavelengths for predicting mechanical properties. We found that the density, porosity, and water absorption of carbonate rocks could be confidently predicted based on spectroscopy data, while the UCS of the rock could also be predicted, but less significantly. The results of the study pave the way for the development of measuring tools for the mechanical properties of rock, based on non-destructive tests of quarrying materials.

Nov 29, 2022

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By G Tranell, E Pastor-Vallés, A Vallejo-Olivares, J B. Pettersen

Metals are essential for the sustainability transition and decarbonisation of society. Yet, it will be paramount to produce them sustainably and minimise the affiliated resource and energy use and the associated emissions. In the circular economy, the metallurgical industry should recycle existing material stocks, and improve its utilisation of wastes, residues and side streams. This increases the complexity of processes, as they become both (often multi-fraction) waste treatment as well as material production processes and brings complexity to the assessment of environmental benefits. Assessing the environmental impact of technological developments frequently is supported by life cycle assessment (LCA). While the method is well documented, its implementation involves several methodological choices that deserve reasoning and analysis, such as how to define the product when former wastes are turned into new products, the selection of impact methodology when converting emissions to environmental indicators, the definition of system boundaries and co-product allocation and the interpretation of sensitivity and uncertainty in final outcomes. In this exploratory study, we investigate how the variation of LCA set-up affects the environmental burden of the system. We consider a metallurgical process where a mix of hard-to-recycle aluminium-containing streams is used to produce aluminium cast alloys in a rotary furnace. Remelting with salt-fluxes allows recovering metals from partly oxidised/contaminated streams, such as dross, bottom ash and industrial shavings, but at the expense of generating significant amounts of salt-slag/salt-cake hazardous waste. The study considers different system alternatives such as landfilling the salt-slag residues versus valourising them into salts, aluminium concentrates, ammonium sulfate and non-metallic-compounds to be used by the metallurgical, construction or chemical industries. Practical recommendations are outlined to facilitate the implementation of LCA in assessing the potential benefits of the circular economy in the metallurgical sector.

Aug 21, 2024

By A Mulyadi, J Barber, R Golden

The Deep Ore Zone (DOZ) underground mine will be a 25 000 tpd mechanised block cave operation starting production in 2000. The ore handling system consists of a direct truck dumping 54 +74 gyratory crusher, which feeds into an ore bin. An apron feeder below the bin is used to load a conveyor belt. This paper describes the design, sequencing and methodology of the crusher station, ore bin and feeder chamber excavations. The Geotechnical investigation and analysis of the site are also discussed as well as the design, installation and quality control of the long-term ground support methods.

Jan 1, 2000