Search Documents

By J S. Kuszmaul, T O. Aspinall

The applicability of environmental geotechnics for erosion management is increasing in importance worldwide. The environmental impact of mining and evolving environmental legislation has been receiving increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental legislative agencies and members of the public. This is because of the need to increase the reliability of erosion prediction and in the minimisation of costs for spoil dump design. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. Engineering design of mine spoil dumps seeks to reduce the potential for such erosion damage through correct selection of an initial stable landform scheme (Goh, 1997). The design of mine spoil dumps must also conform to the specifications of evolving legislation. The Queensland Environmental Management Overview Strategy (EMOS) states that, for minimised degradation of the surface area due to erosion during the development of a project, the erosion rates should be between 12 - 40 tonnes/hectare/year and that the depths of rills and gullies be limited to less than 30 cm (QDPI, 1988). The aim of engineering design is to ensure the long-term stability of the spoil dumps. The implementation of effective planning and operating procedures through recontouring and grading assists in the reshaping of spoil dumps to a safe, stable and non-erodible environment.

Jan 1, 1998

By C Hertle, B Goebel, R Fabre

The mining industry maintains a ælove-hateÆ relationship with water. Dewatering, aquifer, water disposal, irrigation, process water, tailings water, run-off water, seepage, leachate and sumps are all terms that are used on a daily basis in the mining industry, highlighting the numerous water usages on site and their associated quality. According to the Australian Bureau of Statistics (2001), each year the mining industry consumes over 530 000 ML of water. The increasing recognition of water as a limited and valuable commodity, and the associated environmental concerns with the management of water disposal to the environment has led the industry into improving on-site water management. Progressively, water balance models and water reuse strategies are being developed, incorporating more sophisticated water treatment processes. By way of example, membrane technologies, once restricted to industries such as the pharmaceutical industry or the drinking water industry, are now entering the mining world with the aim of producing clean water of suitable quality for ore processing or for advanced treatment prior to release to the environment. This paper will provide a review of the threats and opportunities linked to water use and recovery/reuse in the mining industry in Australia. It will open with an overview of current water usage and associated quality for various mineral industries and continue with identifying the threats and limitations associated with the quality of available water. It will then present how newly developed water treatment technologies and assessment tools can be incorporated into the system to enhance the recovery and reuse of water on site, reduce the risks associated with securing long-term water supply and further improve production, environment and safety (health risk control).

Jan 1, 2006

Several Approaches to Enhance the Bioleaching of Enargite Some approaches were investigated to enhance the recovery of Cu from enargite by bioleaching with Acidithiobacillus ferrooxidans using the galvanic interaction with pyrite and activated carbon, and with thermophilic bacteria, Acidianus brierleyi. Addition of pyrite initially enhanced Cu leaching by the Galvanic effect, but after that the formation of secondary minerals passivated the surface of enargite in inoculated batches. Activated carbon improved Cu recovery from enargite much better than pyrite, when it is contacted with enargite. Recovery of Cu from enargite has been recorded to at largest 2.4 per cent within 30 days in the presence of activated carbon when mesophilic bacteria were inoculated at 25¦C. The recovery of Cu from enargite was drastically enhanced by inoculation of thermophilic bacteria, Acidianus brierleyi, up to 60 per cent within 40 days at 70¦C and still not leveled off after 40 days unless the formation of Fe(III) precipitates occurred. After 40 days dissolved molar ratio of Cu/As is around 5.2, suggesting that metal-deficient sulfides and/or ferric arsenate might be formed on the surface of enargite.

Sep 13, 2010

By Kewu W

Kaolin used as an industrial mineral, especially that in the paper-manufacturing industry, must be of fine size, with high brightness, a low impurity content, and good crystal shape. However, in most kaolin deposits there are various impurities which have a very bad effect on the quality of the kaolin. Therefore, it is necessary to remove these impurities from kaolin ore. Owing to their similar surface properties, the separation of kaolin and iron oxide minerals, especially microkaolin and iron oxide minerals, has been regarded as difficult. The iron oxide minerals often intergrow with kaolin in fine and complicated forms, such as thin films, which make separation difficult. In order to overcome this difficulty, many workers have suggested various treatment methods and obtained great success. Based on research work by Fuerstenau (1980), Huang, Li and Hu (1984), Hui and Wei (1991), Shergold (1978), and Zambrana et al (1974), we have investigated a two-liquid flotation technique for iron removal from kaolin and obtained some success.

Jan 1, 1993

By A Krishnan, C Garcia, I Luna-Berbesi

The discovery and exploration of deposits are progressively shifting to extremely remote regions and greater depths. As a result, exploration costs and the economic risk of a bad investment increase. Current megatrends in the exploration and mining sector indicate a growing demand for the implementation of automation, digitalisation, and machine learning techniques. The implementation of a multi-sensor-based core logging device (DMT, 2024) was done on 400 m of drill cores to optimise interdisciplinary processes in terms of time and quality, by using interlinked and consistent data in real-time, to obtain reliable predictions that support and speed up decision-making. The results are consistent with the laboratory data previously obtained by the mining company, highlighting the benefits of introducing ANCORELOG into their core logging procedures.

Sep 1, 2024

By D Atheis, S Williams, A Dance, D Taplin

"Resurrected from its former life at the Big Bell operation, the grinding circuit at Evolution Mining’s Edna May operation in Western Australia has many a story to tell. The task of optimising a plant designed for another orebody provides as many challenges as opportunities. Initially faced with a blend of primary and oxide ore, the circuit achieved in excess of 320 t/h until the oxide was depleted, leaving only the much harder primary feed.The 2.0 MW semi-autogenous grinding (SAG) mill and 3.7 MW ball mill were assisted by a 150 kW pebble crusher, but the power limitation of the SAG mill resulted in a drop in throughput. Edna May personnel have been involved in a number of progressive improvements to restore the design capacity of the concentrator and work towards 3 Mt/a or even higher ahead of the gravity and leach recovery circuits.These improvements include: a crush forward configuration of the SAG mill scats partial to full secondary crushing variable speed drive upgrade of the SAG mill lifter and grate design changes ball mill circuit grinding efficiency.This paper summarises the chronology of events that has resulted in significant improvements in throughput by conventional (and in some cases, novel) methods of reconfiguring the existing grinding mills. Lessons learned and hindsight perspectives will be summarised, sharing this educational experience with other operations in a similar situation.CITATION:Dance, A, Atheis, D, Williams, S and Taplin, D, 2014. Grinding circuit improvements at Evolution Mining’s Edna May operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By Arthur A. F, MacKenzie I. H

Copper in zinc/lead sinter charged to the Imperial Smelting Furnace operated by Sulphide Corporation Pty Limited at Cockle Creek, New South Wales, concentrates in a complex lead dross which forms as the bullion is cooled to around 400°C. The 0.35 mm portion of this dross, containing approximatelY 67 per cent of the total copper, is treated via a hydrometallurgical route to produce 5000 tonne/yr of CuSO4 5H2O crystal.Around 3000 tonne/yr of copper-lead dross containing 49 per cent copper is leached at 55°C in continuous leach reactors with ammoniacal ammonium carbonate leach liquors to convert copper to soluble copper amine complexes. Leach ettlciencies of 80-85 per cent are obtained. Leach residues are repulped with ammoniacal liquid diluents from the plant and heated in a four stage steam distillation unit to reduce ammonia levels to between 0.5 and 1.0 g/Iitre. The resultant slurry is directed to an effluent treatment plant for final treatment, and separation and return of solids to the sinter plant.Copper is extracted from leach liquor by solvent extraction techniques based on the use of L1X 54 diluted 3:1 with Shellsol 2046 to give a nominal copper loading of 30 g/litre. The loaded organic is contacted with a sulfuric acid solution of pH 5 to remove the bulk of ammonia and zinc, then stripped at 55°C with a 60 g/Iitre H2SO4 95 g/Iitre copper solution to yield a 15 g/Iitre H2SO4 125 g/Iitre copper solution.This liquor is fed to an adiabatic vacuum crvstalliser operating at 35°C and 5 kPa vacuum where crystals of CuSO4 5H2O are formed. Crystals are separated from mother liquor and washed in a two stage pusher centrifuge, then dried in a hot air rotary drier. The crystal product obtained is of a high chemical purity and readily conforms to both Australian and overseas standards.

Jan 1, 1983

By K Eglinton

The extractive industries response to community engagement due to social and political pressures in the 1980s and 1990s was the starting point of development leading to the modern function of corporate social responsibility.Challenged by communities who have greater access to information, demand greater transparency and responsibility of corporate organisations and who possess greater awareness of the communities they participate in, the mining sector faces another step change in how it approaches and integrates corporate social responsibility, transparency and engagement.Mining is seeking reserves of lower grades, in more sensitive environments and in countries with minimal transparency and governance. Not only are the locations changing but so to the stakeholders to engage with and issues to contend with. An increasingly savvy opposition, including not just the ‘green hippies’ but the Gen-Ys interested in the wider sustainability debate and Baby Boomers moving to life style environments, are now questioning mining’s behaviour and encroachment into ‘their space’. Issues including effect on lifestyle amenity, property value, energy efficiency, social provision; concepts such as ‘doing more with less’, participatory engagement, increasing transparency and balancing economic, environment, cultural and social aspects are becoming the norm.The traditional model of supporting local communities, communicating plans and providing employment, community investment and indigenous support programs is not enough. Our industry faces challenges on multiple fronts. It must now be able to address these from a personal/community perspective if it is to remain relevant within communities and play a role in addressing the global sustainability issues.This paper draws on corporate social responsibility trends, integrated functions and implementation approaches through the application of activities within Newmont operations across Asia Pacific.The approach presented works on the philosophy that communities do not necessarily have to like what we do, but should be able to identify and recognise the way in which we involve them in decision making, communicate our intentions and respond to issues.

Nov 22, 2011

By Pinn N

Geosynthetics is an all encompassing word to describe a number of man-made products usually from hydrocarbons which are used in conjunction with the soil. The specific products are:Geotextiles Geomembranes GeonetsGeogrids GeocompositesIn mine establishment and associated construction work, Geosynthetics have proven to be successful in a wide range of applications. For example, geotextiles are now used to assist with the establishment of access roads, site preparation, haul roads and in connection with the construction of embankments for storage ponds and dams as well as for general hydraulic and foundation engineering problems.

Jan 1, 1990

The tragedy of the Moura No. 2 incident has lost much of its emotional mileage for those organisations that thrive on loss and suffering. However, for the families, workers, mine owners and operators in the Queensland underground coalfields, the challenge of delivering a positive outcome, though well underway, is in its infancy. The pressure created by interested parties is necessary for overcoming the inertia involved in change; but they cannot deliver the change. The responsibility ultimately resides at each individual minesite with the people who work there each day.

Jan 1, 1998

By W A. Take, M McKellar, A Walsh, S McDougall, S G. Evans

Recent tailings dam failures have heightened public awareness of the hazard posed by storage facilities for mining waste, illustrating the need for a more critical examination of tailings dam breach mechanisms and the potential mobility of liquefied tailings. Knowledge from tailings dam breach studies will help improve safety and risk management through more accurate inundation maps, dam consequence classifications and emergency preparedness plans. Tailings dams differ from conventional water retaining dams, although dam breach relationships used in practice rely heavily on relationships derived for breach processes from the latter. Physical modelling offers a controlled environment to advance the understanding of tailings dam breach processes, thereby allowing for modelling of simple geometry and boundary conditions to test hypotheses. The performed experiments investigate prototypical tailings dam configurations and material behaviour, with the objective of validating numerical models that will enable practitioners to better assess and mitigate tailings flows resulting from tailings dam failures. Research conducted in the Queen’s University Landslide Flume at the Coastal Engineering Laboratory has investigated the breaching of 1 m high dams with tailings geometry by overtopping initiated by a v-notch incised in the dam crest. This paper presents the initial results of the next stage of this research comparing the outflow hydrograph following loss of containment caused by shear failure to overtopping initiated by notch flow. The two dam experiments presented are constructed with similar dam and reservoir geometries allowing for a direct comparison of the effect on the outflow hydrograph of each failure event. Preliminary outcomes suggest that although both dam failure events are triggered from separate mechanisms their geometries allow for similar values of Q_peak to be reached. Future work is currently planned to expand the shear test series to explore the influence of failure mechanism on the outflow hydrograph.

Jul 1, 2021

The low grade Mount Charlotte orebody was first mined with minimum capital expenditure by mechanised cut and fill stoping. The lower block was prepared simultaneously for open stoping by shaft sinking and installing another crusher and services. Similar development for the third block was discouraged by economic factors and reduced tonnage. Decline develop- ment required less capital and opened up ore reserves commensurate with advance, providing flexibility to stop operations without commit- ment: A 1 in 7 decline measuring 4.25m x 5.5m to accommodate standard Euclid 25 tonne dump trucks was developed south of the orebody. A fleet of four trucks average 12 loads each per shift over a haul distance of 700m.

Jan 1, 1973

Ilmenite production in Western Australia commenced in 1956. There are now five producers, all in the Bunbury-Capel district, and current total production capacity is about 450,000 t.p.a.The deposits occur near the surface and average between 10 and 50 per cent heavy mineral. About 70-85 per cent of the heavy mineral is ilmenite. Other heavy minerals present include leucoxene, zircon, rutile, monazite, and garnet. The ilmenite contains 52-60 per cent Ti02. and is very low in chromium (0·03-0·04 per cent CrS03)Mining is done by sluicing, drag line excavation, or dredging. Primary concentration of the heavy minerals is achieved by spirals, revolving cones, or Reichert cones. After drying and screening, ilmenite is separated from the heavy mineral concentrate by various types of magnetic separator.Separate leucoxene, zircon, rutile, and monazite concentrates are also produced. Each plant uses a different technique and the processes used include chemical attritioning, screen plate electrostatic separation, high tension rolls, air tables, and dry launders.INTRODUCTIONThe treatment of beach sands in the Bunbury/Capel area for the extraction of ilmenite is a very recent development in the mining industry in Western Australia. Nevertheless, since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced (Table 1).The increasing world recognition of Western Australia as a major producer of ilmenite (Table 2) is due primarily to the low chromic bxide content of the mineral (0' 03-0' 04 per cent Cr203), combined with a medium to high titanium dioxide content (54-60 per cent Ti02), supported by large reserves, a stable government, and close access to good shipping facilities. Ilmenite is. produced from these deposits at low cost which enables the industry to compete on world markets despite high rates for sea freights because of the distance from major markets.

Jan 1, 1965

By N Yarahmadi

Characterization of pore pressure is critical for appropriate design of tailings dams. Furthermore, if seepage rates through tailing embankments increase unexpectedly or become uncontrolled, undesirable conditions may prevail to progress piping or internal erosion that could lead to the dam’s instability or ultimate failure. A three-dimensional seepage analysis was performed on a tailings dam using finite element method to find the rate of seepage and pore water conditions in the embankment and foundation. The results were then compared to a conventional two-dimensional seepage analysis carried out on the typical cross section of the embankment and the field data acquired from the instrumentation system. Considering the monitoring data, comparison of seepage analyses results for the two and threedimensional models, showed that the results of the conventional two-dimensional seepage analysis are significantly underestimating reality. Relying on two-dimensional seepage analyses might result in underestimation of seepage rates and impact the safe operation of tailings dams. Similarly, unrealistic prediction of pore water pressure conditions, based on simplified seepage analyses, can lead to overestimation of the rate of strength gain of material and consequently safe embankment raising rates.

Jul 1, 2021

By M Reid, H Arbon

Hillgrove Resources (HGO) commenced open pit mining in 2011 and from 2011 to 2016 the geology team experienced a consistent negative reconciliation between grade control estimated copper (Cu) grade and the mill received grade. For the first four years, despite trialling various grade control strategies, the monthly variance between geology and mill copper grades fluctuated between -5 per cent to -17 per cent Cu metal depending on the style of mineralisation.In 2015, HGO embarked on various measures which resulted in changes to grade control practices under the advice of consultants. These changes to grade control sampling, estimation and block out practices resulted in six to seven months of consistently poor Mine to Mill reconciliations from -25 per cent to -28 per cent Cu.In an effort to mitigate these poor reconciliations the geology team reintroduced the preconsultant block out and geology driven grade control methods. Blockout reconciliations from this point emulated those seen originally from -8 per cent to -12 per cent (Cu per cent). Early in 2016 the geology team introduced conditional simulation for grade control as opposed to ordinary kriging to better characterise the grade distribution, introduced separate estimation parameters appropriate for every zone of mineralisation, implemented a maximum profit function to optimise the selection of ore and waste, and retained the geology driven block out processes. Since March 2016 the mine has experienced consecutive months of positive Mine to Mill reconciliations, the first seen in six years. Year to date the expected copper metal is within 1 per cent of mill reconciled copper metal.This paper will compare the various sampling methods, estimation algorithms and block out procedures from the past six years to arrive at a robust open pit operating procedure applicable for mineralisation with high short scale variability.CITATION:Reid, M and Arbon, H, 2017. Setting new standards at Kanmantoo – effective grade control procedures, in Proceedings Tenth International Mining Geology Conference 2017, pp 401–408 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By M Hedley

Tracking plant and personnel in mining operations provides multiple potential benefits for a mine including improved safety, better monitoring of production, traffic control and, in the future, monitoring and control of autonomous vehicles. The main techniques currently proposed and used for wireless tracking are radio frequency identification (RFID), signal strength based techniques and time of arrival (TOA) based techniques. RFID provide poor accuracy in the complex radio propagation environment present in mines and does not provide continuous tracking and signal strength techniques. TOA based techniques are potentially the most accurate, however, most current equipment has not realised the potential of the technique. CSIRO has been developing the Wireless Ad hoc System for Positioning (WASP) system for wireless tracking in a range of challenging environments including underground mines and surface operations, where GPS reception is compromised by depth. The system utilises a number of ‘anchor nodes’ that are placed at fixed and known locations within the mine and tags attached to the plant or personnel to be tracked. The system provides an ad hoc data communication network, thus, wired data connections are not required to the anchor nodes. WASP uses transmissions in the 5.8 GHz ISM (instrumentation, scientific and medical) frequency spectrum to perform highly accurate ranging between nodes, hence tracking of tags. The localisation performance of the system depends upon the radio propagation environment, ranging down to 0.1 m in low multipath conditions. In this paper we describe the WASP system and provide results of testing in underground and surface operations showing the system achieving high ranging, hence localisation, accuracy.

Nov 22, 2011

By X Sun, L B. Zhou, H Yi, X Tang, P Ning

The rapid industrialisation in China has consumed large amounts of various industrial raw materials, which has left behind large quantities of industrial solid wastes produced from the processes of mining, mineral processing and smelting. The storage of huge quantities of industrial solid wastes is an obvious risk to the environment and human well-being. As the first step to fully appreciate the scale of this risk, it is necessary to carry out research for developing a pollution source environmental risk assessment system (PSERAS), especially for the typical staple industrial solid waste (TSISW). This paper aims to discuss the frame of the PSERAS for TSISW for large scale production. This system consists of two aspects: predicted factors and accidental ones, which involve physical, chemical and biological risk assessments, on-site and during transportation process. Two analysis methods, the analytic hierarchy process (AHP) and fuzzy logic assessment (FLA) were used to handle the complexity of environment and non-quantitative data. The risk assessment system for such a complex objective is difficult and the assessment of relative factors is problematic through the usual quantitative analysis. With the proposed PSERAS, it is possible to define the risk class of pollution sources. Furthermore, the risk assessment results will be helpful to the decision-maker, especially when facing unknown risks in the environmental management of industrial solid wastes. In addition, by means of the PSERAS, risk factors can be ranked against their contributions to environmental risk, in order to calculate their relative priorities in decision-making.CITATION:Sun, X, Ning, P, Tang, X, Yi, H and Zhou, L B, 2012. Environmental risk assessment system for typical staple industrial solid wastes, in Proceedings Life-of-Mine 2012 , pp 301-304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

The difficulty in creating and obtaining a competitive edge in the mineral industry is rapidly increasing. The Kiruna Iron Ore Mine in the far north of Sweden is currently thriving on the world market through firm managerial strategy. LKAB believes in upgrading its raw material to produce a high quality iron ore product for sale to steelworks throughout the world. It is vital that this product is also of uniform quality and quantity to provide quality assurance to customers. The first link in meeting these product requirements starts in the underground workings. Mining methods and operations are of large-scale. Automation and continuous production streamline operations and reduce operating costs. These factors have built Kiruna Iron Ore Mine into the world's biggest, most modern, underground iron ore mine. To remain competitive on the world market, LKAB relies heavily on research and development. The mine is currently in a phase of upgrading its operations. A 25-tonne Toro electric loader is being tested to improve the rate of output of ore from the mine. Long hole drills are being improved to increase accuracy and efficiency. An electronic detonating system will improve detonator delay precision. Projects are underway to better understand ore flow mechanisms from a caving orebody. Benefits include improved ore recovery along with better rock quality control at the caving front. The continued updating of mining operations at Kiruna will enable LKAB to continue to maintain its competitive advantage on the world market in the production of high quality iron ore products.

Jan 1, 1997

By K Sanematsu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Ore deposits of rare earth elements (REE) in South-East Asia are classified into four types: carbonatite, allanite, ion-adsorption and placer. Occurrences of the carbonatite deposits are confined almost exclusively to the Red River Fault Zone of northern Vietnam. Since the carbonatites contain dominantly REE fluorocarbonates (eg bastnasite) and lesser amounts of monazite, they are rich in light REE but poor in heavy REE. The ion-adsorption type deposits and prospects were found in Myanmar, Vietnam and Thailand. The ion-adsorption ores generally show lower REE grades than those of the carbonatite type and placer deposits; however, they could be enriched in HREE, which are more precious and scarce commodities than LREE. The ores consist of weathered granites with a significant amount of ion-exchangeable REE, which are extracted by using a dilute electrolyte solution. The ion-exchangeable REE are likely to be sourced from REE fluorocarbonates, allanite and titanite because these minerals are relatively susceptible to weathering and release REE3+ ions into soil water. In contrast, monazite and xenotime are resistant to chemical weathering and could form placer ores. Placer monazite and xenotime have been processed as by-products of placer Sn, Zr or Ti in Malaysia, Thailand and Indonesia, although the current production is small.CITATION:Sanematsu, K, 2015. Rare earth element deposits and prospective areas in South-East Asia, in Proceedings PACRIM 2015 Congress, pp 671–678 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The experiments described in this paper were carried out as a preliminary to a comprehensive study of the factors which affect the behaviour of lead during and subsequent to deformation by rolling and pressing. These observations are therefore to be considered as introductory to a further paper dealing more specifically with the above-mentioned variables.EXPERIMENTALThe rolling was carried out in a small mill with six-inch diameter surface ground rolls, both of which were electrically driven at 15 r.p.m. The average draft per pass approximated 0·03 in. The pressing was performed between platens in the compression unit of a 30-ton Amsler machine. The flat faces used had a ground finish comparable with the surface of the rolls. All hardness measurements were made with a Herbert "dead load" Brinell machine. The following te'sting conditions were maintained: ball diameter-5 mm.; load-10 kgms.; duration of loading-30 seconds; temperature of testing-16 to 18°C. The hardness values which are given are the mean of two or more impressions made at corresponding positions on the test specimens.PREVIOUS WORKSince the researches of Tresca (1):j: into the nature of the plastic flow of metals during various forging and extrusion...

Jan 1, 1939