Search Documents

Simple parameters, capable of easy observation on-site under operating conditions without interruption to production, are outlined for the operational assessment of underground conveyor systems. Recording techniques, methods of analysis and deduction of operational characteristics are discussed for batch inputs to several points of a multiple belt conveyor system with limited inter-belt storage capacity. Particular attention is given to input and output load- time distributions, utilisation of inter-belt storage capability and system shutdown behaviour. Actual data, observed for a transfer feeder located between two trunk conveyor belts in an underground coal mine, is used to illustrate the operational assessment of an underground system. Load sensitive feedback systems-are briefly considered.

Jan 1, 1982

By C G. Ryan, D R. Cooke

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow-level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-chalcopyrite samples yield a narrow range of δ34 SCDT values (-1.0 to 0.9 ë; n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). Vein quartz from the mineralised zone at Waitangi yields δ18OSMOW values from 6.8 to 12.7 ë (n=23). Fluid inclusion studies indicate a homogenisation temperature range of 190¦ - 296¦C and salinity range of 0.2 - 3.0 wt per cent NaCl equivalent. Similar temperature and salinity ranges have been recorded for the other gold deposits in the Coromandel Peninsula. PIXE (Proton Induced X-ray Emission) analysis revealed that the Waitangi ore fluids have 1090 - 2700 ppm K (average 1600), 145 - 205 ppm Ca (average 180), 80 - 100 ppm Mn (average 90), and 80 - 200 ppm Fe (average 120) but no detectable Cu, Zn, Br, Rb, Sr, Pb and Bi (only one fluid inclusion contains 28 ppm Zn). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source (either directly, or by leaching of igneous sulphides). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1 - 5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in δ18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Mixing of ore fluids with convective ground water is a likely mechanism for gold deposition in a shallow environment for the Waitangi vein system and there is also lack of fluid inclusion evidence (eg liquid-rich and vapour-rich inclusions in the same growth zone) for boiling of ore fluids. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that δ18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1999

Industrial and telecommunications organizations around the world are now turning to optical fibres to satisfy their growing needs for data, voice and video communications and to solve transmission problems in noisy and hazardous environments. Already, coaxial cables have been made obsolete for intermediate and long distance applications and fibres are making in-roads on other copper cable and microwave system techniques.The idea of optical fibres is not new, but techniques to manufacture the high quality cable and components required have only recently been developed. Nonetheless, the technology is now advanced, reliable and mature, and costs are plummeting with increased production and market competition.The mining industry has benefited greatly from developments in electronics and communications over the years. Optical fibres are to have a further significant impact and the time is now right for the industry to begin to exploit the many advantages of this new medium. Applications include data transmission, long distance telecommunications, measurement and control systems, surveillance, computer networks, etc.This paper briefly describes the characteristics of optical fibres, current status of the technology, applications and possibilities for future development.

Jan 1, 1984

By Singh TN

Rampura-Agucha Zinc-Lead deposit is unique as it is reported for the first time in the gneissic terrain with a rich oregrade quality of early to middle Proterozoic of Bhilwara supracrustal belt in the Precambrian of Northwest India. These sulphide ores are mostly confined to the graphite bearing Quartzofelspathic gneisses with intermittent bands of Calc-Silicate granofels and amphibolite. The ore and country rock mineralogy and their textural features are indicative of highly metamorphosed deposit and further the presence of marmatite and monoclinic phyrrhotite revealed high temperature environment of deposition.The present paper deals with some of the ideas about the ore genesis and petrographics of the associated rocks for Rampura-Agucha Zinc-Lead deposits of Bhilwara District (Rajasthan).

Jan 1, 1990

The widely accepted concept of mineral resources are that they are finite - mining therefore being intrinsically unsustainable. Yet the modern global mining industry continues to grow production at strong rates - how can this be? In reality, mining is a complex industry, starting with exploration, development, operations and then rehabilitation and closure. A recent major study of Australia has shown that for most mineral commodities, exploration continues to find new deposits, or expand resources at existing mines. In parallel, however, there are a number of key 'mega-trends' which are growing in their importance - declining ore grades (or quality), increasing tailings and waste rock volumes, the need for deeper mining, more refractory ore types, increasing energy inputs and higher unit energy costs, increasing pollution issues and, of course, not to forget greenhouse gas emissions issues. This paper will present a detailed case study of the ultimate sustainability of the Australian mining industry - showing long term historical data sets on ore grades, waste volumes and economic resources and placing these trends in light of major twenty-first century issues such as energy supplies (especially Peak Oil), climate change and existing and emerging land use conflicts (eg agriculture versus mining). Australia is a critical case study in the sustainability of mining, as it is a major global exporter of numerous commodities, and this is expected to continue to underpin the ongoing industrialisation of countries such as China and India. The ultimate question begs - can Australia actually meet this fundamental challenge, or will our resources run out, or will we be constrained by environmental issues such as climate change, land use or perhaps water? Rather than a mere optimist's or pessimist's view, this paper will present a range of hard data which underpins the debate about the sustainability of mining this century: ultimately, we cannot assume that the patterns of past mining will continue to work in the future. The sustainability of mining continues to hang in a precarious balance.

Jun 1, 2010

By Frew J. A, Harris M. C, Manlapig E. V

The recovery achieved in a flotation process is a function of both the characteristics of the feed stream and the operating conditions within the flotation cell. In this paper, the flotation characteristics of the streams within the Red Dog le

Jan 1, 1997

Upper Cretaceous and Eocene coal measures of the Ohai Coalfield are stratigraphically complex, and coal seam geometry and quality are influenced by washouts and partings resulting from accumulation in a fluvially active environment. Mining efficiency is influenced by these seam discontinuities, which are difficult to predict in the absence of refined paleoenvironmental models of peat accumulation. Petrographic variations between the Upper Cretaceous and Eocene coals indicate differences in the environments of peat accumulation. Seams in the Upper Cretaceous Morley Coal Measures accumulated autochthonously (in situ) in predominantly forest swamps with a high water table. These swamps were occasionally subject to brief floods. No significant changes in swamp vegetation, as indicated by petrography, have been detected between seams. In contrast, the greater content of mineral matter and maceral detritus within the Eocene Beaumont Coal Measure seams indicates hypautochthonous (locally transported) peat accumulation under more frequently flooded conditions. A precursor forest-moor is again indicated but the greater resin content of these coals compared with the Upper Cretaceous examples may suggest a greater contribution from conifers. Integration of coal petrography with investigation of other seam characteristics and coal measure sedimentology is expected to result in a detailed understanding of original depositional controls on peat accumulation. Paleoenvironmental models derived in this way should facilitate prediction of seam geometry, roof and floor conditions, and variations in coal quality, with obvious benefits to exploration and mine development.

Jan 1, 1983

By S D. Golding

The current study integrates hydrogeochemical and stable isotope results to investigate the sources and evolution of acid mine drainage at the historic Mount Morgan gold mine in Queensland, including the controlling factors and mechanisms of sulfate formation. The open pit and seepage sumps contain acid-sulfate waters and show elevated Al, Cu, Fe, Mn, Pb and Zn values. Samples collected from the Dee River bordering the mine site are less acidic, with lower concentrations of dissolved metals that gradually attenuate downstream from the mine. Concentrated acid mine waters has lead to formation of efflorescences consisting mainly of hydrous Fe-sulfates. The results of the ongoing isotope analyses on water samples show distinctive grouping of the data. The range of the sulfur isotope values for dissolved sulfate in samples from the open pit and sumps (d34S = 2.1 to 3.0 per mil) are similar to those of sulfides in the Main Pipe mineralisation (d34S = - 0.2 to 2.8 per mil). The lack of fractionation between sulfides and sulfate indicates that intermediate oxidation states of sulfur are not significant and makes this technique a useful tracer to identify the sources of sulfate. The Dee River samples, on the other hand, have heavier sulfur isotopes (d34S = 2.8 to 5.0 per mil). These samples may contain dissolved sulfate from æinternal sourcesÆ in the river basin, show local bacterial reduction or indicate a simple mixing trend. Further isotope analyses including oxygen isotopes of dissolved sulfates will enhance the interpretations.

Jan 1, 2003

By Weatherhead J, Grounds J

The Nabarlek Uranium Project located in Arnhem Land in the Northern Territory of Australia was a small high-grade deposit which was the first uranium mine brought into operation following the extensive Commissioner Fox Inquiries into uranium mining during the late 1970s. The operation is almost complete and decommissioning plans have been prepared. This paper reviews all phases of the water management and tailings disposal for the project and compares results with design predictions.

Jan 1, 1988

By Roach C

Exploration on the Callide Coalfield by Thiess Bros. Pty. Limited had reached the stage in mid 1976 where there was a need for a comprehensive appraisal of the coalfield geology. Exploration strategy in 1977 - 1978 was defined by the selection of the most attractive targets. All available literature, reports and plans were reviewed and borehole records assessed. The geology of the coalfield was placed in its regional setting and the genesis of the Callide Coal Measures described in a structural and sedimentological context. Their general form and extent was then examined by the technique of stratigraphic analysis through the interpolation and extrapolation of the available data. A "localized" reserve classification was drawn up and reasonable estimates of the various geological reserves produced, in terms of their reliability and depth of overburden. Quality trend maps were also produced. The resultant "base map" was virtually a summation of all the information to June, 1977, and the basis for the exploration programme in the 1977 - 1978 financial year. The technique allowed for "base maps" to be produced at almost any stage, each one a refinement of its Predecessor.

Jan 1, 1978

Recovery of Fine Gold Particles from Philippine Gold Deposits by Enhanced Gravity Concentration and Flotation The objective of the study is to determine the applicability of enhanced gravity concentration (EGC) and flotation for gold recovery. While gravity concentration methods have long been applied to gold ores, especially to free-milling types that requires minimal beneficiation, flotation for gold recovery has not yet taken hold as a major operation in the Philippine setting. In this study, the application of EGC and flotation for gold is applied and compared to the existing methods for gold recovery. Two samples, with assays of 7.315 and 5.333 g Au/MT (samples 1 and 2, respectively) are used for this study. These samples are subjected to mineralogical studies and is found to have a gold-particle size ranging 10 to 200 microns. To verify the separation size, the mesh-of-grind (MOG) is used as the primary parameter for experimentation. Initially, the samples are stage-crushed, ground, and subjected to EGC using a Falcon SB40 Concentrator. Based on the results, the two samples showed that recovery increases with a finer MOG. The ratio of concentration (K) decreases with a finer MOG. This shows that there should be sufficient liberation of the gold values for EGC to be effective. The effect of the enhancement is to pronounce the difference in specific gravity of the minerals, promoting better separation. This is validated by the high recovery values of 86.97 per cent and 98.73 per cent exhibited respectively for samples 1 and 2 (at 54 microns). For the flotation runs, sample 2 with an average particle size of 80 per cent passing 74 microns is examined using thiocarbamate-based collectors for roughing and subsequently exhibited a recovery of 96.32 per cent. At this point, the concentration ratio (K) is noted as an important efficiency indicator for flotation process since it yielded a very low-mass and high-metal content concentrate.

Sep 13, 2010

By Ormsby W. R, Farrar L

The stratigraphy of the central Pine Creek Geosyncline has been simplified into a three-fold subdivision comprising the Batchelor, Frances Creek and Finniss River Groups. The Batchelor Group consists of a sequence of shallow water coarse clastics and crystalline carbonates and is conformably overlain by the marine carbonaceous shale dominated Frances Creek Group. Interbedded within the carbonaceous shale are turbidites, iron formation, tuffs, carbonate and non carbonaceous shale. The Finniss River Group is a flysch sequence of greywacke and mudstone. The stratigraphic and structural evolution and igneous history are all interrelated. Although the Batchelor Group may have formed in a tensional regime, it is likely that regional compression and accompanying thin skinned deformation began during deposition of the Frances Creek Group. Continued compression resulted in D2 folding d6collement deformation, wrench faulting in compressional zones and thrust faulting. Occasional relaxation of compression is marked by a number of periods of basic intrusion and perhaps distal volcanism. The style of deformation within sediments varies away from granitic basement highs and is similar to that observed around salt domes and found in experimental diapiric models. Sedimentary facies changes also indicate local emergence of basement highs during sedimentation. As compression continued, the deposition of thick sequences of the Finniss River and El Sherana Groups brought about regional metamorphism. Relaxation of compression and waning of associated subsidence resulted in a relative increase in the rate of uplift and partial melting of diapiric sialic basement. In places, granitic magma moved upwards and crystallised forming grossly concordant bodies. Other masses moved laterally and formed extensive granitic sills. Later compression periods caused mainly brittle deformation which may have been strongly influenced by underlying basement fabric.

Jan 1, 1994

By Kerr M. H, Slaughter P. J

Design of the new cemented hydraulic fill plant was based mainly on experience with a succession of previous fill plants. Two stage cycloning of combined concentrator tailings was introduced. Design of the two stage cyclone configuration was assisted by computer simulation of cyclone performance. Cementing additives, namely Portland cement and ground copper reverberatory furnace slag, drawn from bulk storage, are pre-slurried prior to mixing with hydraulic fill. Quality control of fill being sent under- ground is achieved by a series of automatic control loops. Plant instrumentation was given prime consideration during the design phase. Inventory checks of all mass flow metering equipment are made at regular intervals. Fill is pumped to boreholes at several locations. Details of the equipment and operating procedures for the plant are Discussed.

Jan 1, 1973

By J L. Edwards

High resolution, acoustic scanning technology has emerged in recent years as a powerful wireline tool for identifying the occurrence and orientation of structures and borehole breakout û the latter being a strong indicator of horizontal stress directions. While other wireline techniques such as dip metre and calliper logging can provide some of these data in a fairly rudimentary way, the quality and ease of interpretation of acoustic scanner logs provides a level of detail that significantly enhances the risk profile of the analysis which more than compensates for their additional upfront cost (MacGregor, 2002). As is often the case with such technology it is one thing to generate a data set that describes the attributes of the various features apparent in a log, and another to be able to analyse those data in such a way that their individual and collective impact on mine planning issues can be readily assessed (MacGregor, 2003). This paper describes a process for the interactive manipulation and visualisation of joint and breakout data to enable them to be effectively included in the mine design process.

Jan 1, 2009

The Australasian Institute of Mining and Metallurgy brings together, voluntarily, people with a professional interest in the disciplines and skills which are employed in the mineral indus- try, and in relation to that industry. We come together because we have a mutual interest in improv- ing what is done by the mineral industry, in all its aspects. It is this sense of continuing improvement, of doing better, of doing as well as we can, as our knowledge and skills improve, that unites us in creating and fostering a professional association of like- minded people. We know from our professional training and experience that enormous progress has been made, at an ever-increasing rate, in the mineral industry, particularly in this Century. We know that the mineral industry has played a very major role in providing the means by which so many more people survive to live longer, healthier and more interesting lives, than ever before. Indeed together with the oil and gas industry, which is an integral part of the mineral industry but has achieved its own commercial dis- tinction, it is fair to claim that the mineral industry has played the major role in providing the means for the advancement of the human quality of life.

Jan 1, 1988

By Pirvics AI, Whitworth NR, Tuppurainen JMI

Process control applications to the unit operations in both the Lead and Copper Smelters are reviewed. The basic aim of this control is to smooth plant inputs to produce an output of consistent quality in terms of chemical composition, temperature and physical properties. Most effort has been put into the process bottlenecks, namely in the process baghouse of the Lead Smelter and in the Copper Smelter reverberatory furnaces. The method of approach is discussed, firstly extensive plant measurement and data logging plus identification of factors which most affect the unit operation and secondly control of these factors to smooth out variations. This has been possible due to the development in-house of on-line instruments to measure the critical variables and the external use of computers for plant control. Some of these instrument developments are also briefly discussed.

Jan 1, 1984

By M Liang, C Putzmann, D Gokaydin

The mining industry faces numerous challenges in swiftly evaluating and exploiting new mineral deposits to meet the escalating demand for critical minerals and metals. These challenges necessitate the adoption of innovative techniques and technologies to expedite development cycles and facilitate the efficient exchange of knowledge and expertise. Traditional mineral exploration methods rely heavily on data governance, visualisation tools, and expert interpretation skills, often operating in isolation and limiting the integration of valuable data and knowledge (Lindsay and Perrouty, 2019). To address these integration challenges and bridge the industry’s knowledge gap, the concept of a digital twin offers a holistic solution (Ahn, 2021; Nagovitsyn and Stepacheva, 2021).

Sep 1, 2024

Investigation of the Classification Operation in a Coal Pulverising Vertical Spindle Mill Coal pulverisation in power plants is a major electrical energy consumer. In 2006 more than 41 per cent of world electricity generation was from coal where pulverisers use 0.5 to 1 per cent of gross generation. Therefore, pulverisers are an important target for optimisation not only for reducing costs of power generation but also for reduction of greenhouse gas emissions. A better understanding of the operation of pulverisers is an essential requirement for their optimisation. However, little information is available, other than operating experience, on the performance of pulverisers and how these react to changes in operational variables. This study investigates the effect of changes in coal and airflow feed rates on the classification performance that occurs in an industrial scale ball-and-race vertical spindle mill in which the pulverisation and classification processes are linked together due to the separator classifier being an integral component within the pulveriser. In order to decouple the breakage and classification processes, samples were cut from upward flowing streams through sampling ports drilled on the pulveriser body at different locations. Specific sampling tools were developed. Samples collected from the pulveriser were size and density fractioned to distinguish the differences in behaviour of the components, namely coal and mineral matter. The coal flow rates on dry basis within the mill and around the separator classifier were calculated by mass balancing the multi-component data. The difference in classification behaviour of components during pneumatic transport was confirmed. The response of the circulating load in the mill (~600 to ~1100 per cent) as well as the dependency of fineness of the streams to the operating variables was demonstrated. The approach taken in this study has proved that development of a classification model for a vertical spindle mill pulverising non-homogeneous materials, eg coal, requires treating these materials as multi-component/composite substances.

Sep 13, 2010

By Ellis CG

The N.S.W. Department of Mineral Resources commissioned its first Mobile Gas Laboratory in 1973.Although originally intended for diesel exhaust analysis, it has been progress- ively made more suitable for mine air analysis. Currently there are two upgraded units in operation. These laboratories have been used at the scenes of four mine fires, two mine explosions and three recovery operations. The authors' experience jointly covers all of these incidents. In this paper they recount the role of the Mobile Laboratory in each incident - including the difficulties encountered - and trace the development of these units to their present state. Future improvements are foreshadowed, and some comments offered concerning the likely future role of these vehicles in mine Emergencies.

Jan 1, 1981

By R Kroukamp, G Rech

CRONIMET Australia in cooperation with Speciality Metals International, the mining lease holder of the Mt Carbine Tungsten mine, have demonstrated the preconcentration and processing of large (>12 million tonnes) tailings and mine waste dumps on site in far north Queensland. The first stage of this project has proven the economic viability of preconcentration using sensor-based particle sorting whilst ensuring high recovery of industry critical tungsten minerals – wolframite and scheelite. Sensor-based sorting technology have enabled the production of a sorter product to feed the existing wet gravity plant ensuring higher recoveries and increasing concentrate production. Processing of 1,000 tonne low grade samples using the TOMRA x-ray transmission (XRT) ore sorter installed on site, has reduced the volume of material entering the downstream wet processing plant by up to 60%. The sorted 10-25mm size range produced the highest upgrade ratio (product/feed) of 24:1 and achieved sorter concentrate grade of 1.52% WO3, sorter waste grades below 0.014% WO3 and metal recoveries of up to 93.4%. The appropriately sized, barren sorter waste material is also sold as aggregate and other quarrying products and thus adding to the overall economic benefit of the project. The utilisation of the sorting technology on site has produced an economically viable project, significantly reduced capital cost, and reduced the time to market of the final tungsten concentrate. The next phase of the project includes design and installation of a larger two sorter plant capable of over 150t/h feedrate.

Nov 10, 2020