Search Documents

Felspar occurs in association with quartz in the Broken Hill lode pegmatites and is brilliant green, greenish white, and white in colour. The pegmatites occur mainly in the walls in sporadic patches, parallel to the general dip of the ore deposit. The occurrences are of no economic value.Deposits of marketable felspar occur in pegmatite in a number of localities around Broken Hill, New South Wales.The majority of these are in the form of an irregular outcrop, usually of tapering length and depth. The maximum depth of any deposit yet worked in the district is about 40 ft. The felspar is occasionally contaminated by "blows" of quartz, mica and beryl, but the two latter are profitably marketable when separated.Felspars vary in colour from pink, through grey to snow white, and the colour is not indicative of the mineral content. The largest deposit at present being worked is the Egebeck quarry, about 14 miles south of Cockburn. It is a prominent outcrop, roughly circular and about 150 ft. in diameter, covered by one to three feet of overburden.The felspar is mainly massive, but contains some cleavage planes at approximately 90°. Intrusions of quartz and mica occur in patches, but the deposit appears likely to improve in size, regularity and quality below the present working floor.COMMERCIAL USES.Commercial felspars are mainly used in the ceramic industry, for which a high-grade potash felspar is required.The dental industry requires limited amounts of soda felspar with a very low Fe20s content. The poorer grades...

Jan 1, 1946

By Denby B

The ever increasing demand on land use has led to large areas of land being considered for development, which because of past mining activities are covered by substantial depths of fill materials. This paper examines the problem faced with the development of land infilled with open cast mining backfill, in predicting the behaviour of the fill upon development. To be able to design foundations suitable to withstand the movements that occur within open cast backfills or design a backfilling operation that produces land suitable for a proposed after development, a means of predicting backfill settlement is required. Factors critical to this prediction are the timing of backfilling operations, the compactive state of the backfill and the inundation of the backfill. The analysis of a considerable quantity of data collected from the monitoring of backfilling operations and backfill movement at a range of open cast coal sites located within the UK has given the authors a better understanding of how open cast backfills behave in terms of long-term creep settlement, collapse settlement and how these are effected by backfill scheduling. This knowledge has been encoded into a program running under Microsoft Windows that enables a user to make settlement predictions for a point, a given section or area or for the whole site. Differential settlements, critical to any development design, can also be determined between any two points taking into consideration the heterogeneous nature of open cast backfills. The program was tested with data from an open cast coal site in the UK. Compaction monitoring during the placement of the backfill material enabled a model of the backfill to be constructed taking into account backfill properties and scheduling. This model, taken as input into the program, enabled future backfill settlement predictions to be made. A comparison is given between these results and actual settlements obtained from a short-term settlement monitoring scheme.

Jan 1, 1995

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are steel-based, thin-walled tubular ground reinforcement widely used in underground mines in Western Australia. Following installation these stabilisers are subject to corrosion which may reduce the load carrying capacity and lead to unexpected ground falls. Although corrosion has been recognised as a common occurrence, particularly under aggressive mine water and mineral conditions present in underground mines, the knowledge of the effects of corrosion on the mechanical behaviour of FRS is limited. The Department of Minerals and Energy of Western Australia has conducted a laboratory based program of studies to investigate the effect of corrosion on the mechanical properties of FRS. The studies have focused on the effect of corrosion on tensile strength of FRS and frictional resistance along the interface between FRS and the drillhole wall. The results indicate that under certain conditions corrosion damage can significantly reduce the effectiveness of FRS.

Jan 1, 1996

By A-M Fleury

There has been much progress on the issue of acid drainage over the past 20 years; however, significant challenges remain. The International Network for Acid Prevention (INAP) is attempting to address them by globally coordinating acid drainage information sharing and research. INAP pursues three branches of activities: it links AD research, practice, and people; it organises, sponsors, and participates in regional workshops as a forum for technology transfer; and it instigates and funds key acid drainage research projects. Through these activities INAP is helping the industry deal with what is arguably its most serious legacy issue.

Jan 1, 2003

By Gupta R. C

Syria has about 500 million ton deposit of minerals having 34 per cent iron content with alumina and silica as major impurities. Efforts were made to see the feasibility of concentration by four different methods involving washing, high intensity magnetic separation, reduction roasting and magnetic separation and acid leaching technique. It was observed that the reduction roasting with magnetic separation yields a concentrate with high iron (62.3 per cent) content without requiring water which is a scarce raw material in the region. The paper concludes that the detailed study may be made following this route to optimise the process Parameters.

Jan 1, 1999

A great part of the research on froth flotation of gold ores deals with ores containing gold associated mainly with sulphides, resulting in a largely accepted view that what takes place with sulphides (eg pyrite) in a flotation cell also happens to gold particles. This paper is concerned with the influence of some inorganics (CuSO4, CaO and NaCN) on gold particles flotation, using ethyl or amyl xanthates as collectors. The bench-scale tests were carried out with ground quartz and gold particles mixtures. Some findings stemmed from this study: flotation of the gold particles of size 0.16 mm was efficient adding only frother; larger gold grains were better recovered by the use of stronger collector CuSO4 did not seem to be an activator for gold; the addition of NaCN up to 200 g/t or CaO up to 2000 g/t did not depress the gold grains when amyl xanthate was used as collector although with ethyl xanthate the gold depression was verified.

Jan 1, 1993

By T Baard, A Pieters

This paper deals with the design and implementation of a 17 MW (nominal) surface cooling installation at Impala Platinum No 14 shaft located in Rustenburg, North West Province, South Africa.The cooling requirements included the installation of a surface ammonia refrigeration plant complete with the storage of hot and cold mine service water for underground use. It was also necessary to install a surface bulk air-cooling facility, which cools 400 kg/s of ventilation air going to the underground workings. Primary cooling is to the surface bulk air cooler. The cooling duty of a surface bulk air cooler is heavily dependent on the ambient wet-bulb temperature. Because of the daily wet-bulb temperature variation in this part of the world, use was made of a cold thermal storage facility of four million litres. The excess chilled water is stored during the night, for use by the main drilling shift during the day. This keeps the refrigeration machines as close as possible to full load during the summer, thus maximising the use of the capital expenditure. This paper discusses the control philosophy used to maximise the cooling output, as well as the thermal process. The project consisted of two phases resulting from the underground development phases of the mine. The first phase started in January 1999 and was commissioned by the end of the same year in record time. The final commissioning of the second phase took place at the end of 2002. The most difficult part of the construction phase was the tunnelling of a subsurface air duct from the bulk air cooler to the operating vertical shaft. This was done without disruption to the hoisting of men, material and ore in the shaft. Owing to the size of the refrigeration machines, the ammonia quantities involved and the application on a mine (no ammonia can go underground, either in the service water or in the mine air) special precautions had to be taken. South Africa has developed high standards for ammonia refrigeration plants used on mines, which will be partially dealt with in this paper.

Jan 1, 2005

By Bishop I, Toon S

To determine whether 130 felt earth tremors around Edwinstowe, Nottinghamshire U.M, which also experienced severe surface fissuring, were caused by coal extraction, a surface seismometer array was established around Thoresby Colliery. Over the next year, 785 microseismic events were detected. The spatio- temporal seismicity patterns are clearly associated with the commencement, continuing extraction and closure of faces. Of particular note are events which locate at the surface and appear to be related to the active fissuring. Events occur within days of commencement of production and cease when production finishes, with good correlation between face advance and hypocentral position. Naturally occurring microseismic events have also been detected up to 1 km ahead of active longwall faces in the Midlands using triaxial geophone packages grouted into the seam together with a surface seismometer in the top of the borehole. The quality of these data were very high and guided waves can clearly be seen with the dispersive characteristics associated with seam waves. In one experiment more than 2000 events were detected in only two days of monitoring even in a relatively noisy surface environment. This paper demonstrates how very accurate locations (5 10 metres) can be generated using three-component digital data from only one borehole. The surface seismometer and the borehole P-wave onset can give extra precision for the height of the event relative to the seam. The event distributions give a dynamic, three-dimensional image of the developing patterns of fracturing above, below and ahead of the longwall face with important implications for roof control, subsidence prediction and gas Migration.

Jan 1, 1992

Competitive commercial circumstances internationally provide a prime impetus for miners to seek new technologies as a means to profitability and survival. Engineering and project management activities play a vital role in establishing, operating and developing the capital facilities used by miners. Computer based technologies are the single most important technology for maintain- ing competitiveness in engineering and project management into the future. Current applications of computers in engineering design and drafting are finding economic applications, computer-aids are more readily introduced, accepted and profitable. Computing technology is advancing very rapidly and on a broad front in hardware, software and communications. This technology advance is improving the ability of engineers and project managers to provide a high quality, responsive and low cost service which will improve in parallel with computer technology. As this technology advances, a key challenge is created for managers in selecting hardware and software, in developing people and organisations and in marketing the technology to advantage. While the future holds many exciting developments, people will still hold the key roles. While the nature of their roles may change, the final acceptance or rejection of technology will be by people, whether as users or owners, who will judge on the basis of whether their stake is improved or not.

Jan 1, 1986

By B Taylor

The Perseverance deposit is the most southerly known economic copper/gold deposit within the Cobar gold field. The deposit is situated approximately 12 km to the south-southeast of Cobar and is essentially blind to surface with the top of economic mineralisation occurring 750 m below ground level.Based on the December 2010 resource estimate (inclusive of reserves and net of depletion) the deposit contains 3 011 000 tonnes at 6.1 g/t Au and 0.90 per cent Cu (590 000 oz of gold and 28 000 tonnes of copper). The deposit is comprised of four principal lenses, the Perseverance, Hulk, Zone B, and Hercules lenses. In excess of 90 per cent of the known resource tonnes are contained within the Perseverance and Hulk lenses. The deposit is shear related and hosted within lower Devonian rocks of the Cobar Basin. The competency contrast of rhyolites juxtaposed against sediments by the Peak-Perseverance shear is the principal control on mineralisation. Both the Perseverance and Hulk lenses are primarily hosted by brecciated rhyolites juxtaposed against Chesney formation sediments across the Peak-Perseverance shear. This faulted rhyolite sediment contact roughly defines the global orientation of the deposit. The Perseverance lens continues within the shear for up to several hundred metres beyond the extent of the faulted rhyolite sediment contact. Mineralisation within the shear beyond the faulted rhyolite contact zone is hosted by sheared silicified sediments. The Perseverance lens remains open at depth and to the south.The Zone B and Hercules lenses, which are significantly less important in tonnage terms, are hosted by rhyolite breccias within the main body of the rhyolite and appear to be only tenuously related to the Peak-Perseverance shear. Within the Perseverance lens, the presence of northeast trending high grade breccia veins developed oblique to the north-south trending shear system has led to the development of steeply north plunging high grade ore shoots within a globally north-south trending mineralised domain. These high grade shoots have limited horizontal continuity but significant down plunge extent.The presence of coarse gold and the resulting strongly skewed nature of the gold grades, in conjunction with controls on mineralisation which are not parallel to the mineralised domain, has led to predictive difficulties regarding stope performance.Strong heterogeneity of the gold content of the ore and geological controls on mineralisation which are not parallel to the global trend of the mineralisation impose a set of difficulties which sound geological control is helping overcome.

Aug 22, 2011

Although the pattern of metamorphic zones south of the Thackaringa-Pinnacles Fault is much obscured by polymetamorphism, displacement of the orthopyroxene isograd by the fault agrees with the displacement of a horizon of "banded aplite" mapped by Andrews (1922). A dextral transcurrent component of 20,000 ft is indicated.INTRODUCTIONThe east-west Thackaringa-Pinnacles Fault (Andrews, 1922; King and Thomson, 1953), one of the major geological structures in the Broken Hill district, New South Wales, cuts across the general north-easterly strike of outcrops and fold structures of the Willyama Complex. The degree of shearing and recrystallization in its unusually wide crush zone and the manner in which adjacent rock units and structures have been dragged into conformity with its strike denote considerable movement on the fault. Information concerning the nature of this movement is of critical importance in the search for possible continuations or repetitions of lead-zinc mineralization south-west of Broken Hill.A transcurrent movement of 20,000 ft, with the southern block moving west, was estimated by Andrews (1922), who correlated prominent outcrops of "banded aplite" at The Pinnacles (north of the fault) and Big Hill (south of the fault). Displacement of this order, however, does not seem sufficient to explain the extent and character of the fault zone. Recent chemical and petrological studies of the banded aplites at The Pinnacles and Big Hill by Vernon (19B1) confirmed their similarity, but indicated an origin by metasomatic replacement of pre-existing folded and metamorphosed rocks. This raises the possibility that some...

Jan 1, 1965

By Corbett GJ, Leach TM

ABSTRAC'T' Although hosted within an Ordovician magmatic arc, the Peak Hill high sulphidation system displays features typical of younger Pacific Rim high sulphidation epithermal gold deposits. Regional NW trending transfer structures are inferred to localise the magmatic source at their intersection of the NS trending arc. Fluids have migrated from the magmatic source along NW structures and thence exploited permeable horizons, which have become silicified. Alteration displays typical zonation from silicification through assemblages characterised by alunite, pyrophyllite and kaolinite and is followed by breccia/fracture controlled sulphide and gold deposition. Sinistral rotation on the NS arc has dilated NW trending fractures to produce the WNW to EW dilational fractures which host the higher grade ore. Mineral assemblages are typical of formation distal to the magmatic source in an epithermal environment. The combination of alteration and mineralisation zonation with structure provide fluid vectors which target a magmatic source to the SE of Peak Hill.

Jan 1, 1995

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

In the last eight years inclined conveyor haulage systems have established themselves in the mainstream for hard rock underground mine haulage. This leaves the question; what else might be on the horizon for mine haulage and how do we address the process of selecting haulage systems for new mines? This paper considers the identification of viable haulage technologies for underground mines and explores an approach for assessing existing and potential technologies. The example of a large deep mine is considered here. The evaluation of existing haulage systems relies on precedence and the assessment of the system capacity to meet the haulage requirements envisaged for a particular mining project. The assessment of potential technologies for mine haulage relies on the capacity to deliver a viable production-scale system within the timeline envisaged for developing a mining project. The haulage technologies addressed in this paper include: shaft hoisting,conveyor haulage,truck haulage,vertical conveyors, andhydraulic hoisting. This paper does not consider rail haulage out of a mine. This is simply because Australian topography typically has insufficient relief to bring them into consideration. However, rail haulage is a widely used and effective haulage solution in situations where significant topographical relief is present. The assessment of haulage system capability focuses on the following fundamental questions: How reliable are they? What is the degree of technical risk in a business context?What levels of flexibility do they offer?How capital effective are they? What returns are indicated by the balance of capital and operating cost estimates?

Jan 1, 2008

By D Fukuda, K Kaneko, R Kudo, J Kodama, Y Fujii, T Sasaki

"Estimation of stress state as well as elastic modulus is important for the prediction of a rock slope deformation in an open pit mine since it can strongly influence the mining-induced deformation of the rock slope. This study applies a method to evaluate regional stress state and Young’s modulus by analysing the mining-induced deformation of ground. The effect of changes in regional strain state due to tectonic plate motion can be accounted for using the proposed method. Mining-induced deformation can manifest itself as changes in ground surface geometry resulting from mining activity. There are three underlying factors that can contribute to the deformation: displacement induced by the effect of gravity displacement induced by the effect of horizontal regional strain incremental change in the horizontal regional strain. The relative displacement arising from the mining excavation at the Torigatayama limestone mine in Japan has been measured by Global Positioning System (GPS). Both the regional stress state and Young’s modulus were estimated by back analysis of the change in distance between GPS stations using a 3D finite element method. It was shown that the reliability of the estimation improved with an increase in displacement due to mining progression. It was also shown that values for Poisson’s ratios of less than 0.10 are reasonable estimates with values for Young’s modulus between about 5?GPa and 10 GPa. The magnitude and direction of the maximum compressive stress in the district surrounding the Torigatayama mine were estimated to be between -6.4 MPa and -4.4 MPa and around N25E respectively.CITATION:Kodama, J, Sasaki, T, Fukuda, D, Kaneko, K, Fujii, Y and Kudo, R, 2014. Estimation of regional stress state and Young’s Modulus of ground at Torigatayama Limestone Mine in Japan, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 135–142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By Corbett GJ, Leach TM

The Nena Cu-Au high sulphidation deposit has formed within the Frieda River Intrusive Complex in association with a major dilatant structure. Multiple intermediate intrusives of Miocene age are localised by a splay (Frieda Fault) of the Fiak-Leonard-Schultz Thrust, a several hundred kilometre long structure, formed parallel to the accretionary prism of northern Papua New Guinea.The high sulphidation systems including Nena, crop out as narrow silica-alunite ridges extending for up to 5-6km in length within a dilational structural environment. Alteration at Mena exhibits two phases of hydro-thermal activity: an initial stage, inferred to be volatile-rich, which has produced zoned alteration; and a later phase, postulated to have been a liquid-dominated fluid, which has brecciated earlier alteration zones and deposited gangue phases as well as Cu/Au-bearinq sulphides in open spaces.

Jan 1, 1994

IF lead be heated with concentrated sulphuric acid two distinct actions will usually be observed. In the first, bubbles begin to be evolved more or less rapidly from the lead, and in the second, which occurs at a higher temperature than the first, hydrogen and sulphur dioxide are evolved, free sulphur is liberated, and leadsulphate is formed. The second action may be violent and usually continues till the lead is all consumed.Attempts have been made to apply these reactions, by means of a standard procedure, as a "Flash test" for the acid resisting qualities of chemical sheet lead. The purpose of this article is to comment on the best method of performing the test, on the various phenomena which may be observed during the course of it and on the interpretation of the results when obtained.PREVIOUS WORKIn 1919, Barr...

Jan 1, 1930

A biological column leach testwork program was undertaken on a chalcocite ore. Three tests were conducted in all, using 65 in x 100 mm columns in three sections. The tests were started with varying acid strengths and inoculated with bacterial solutions from previous column testwork. The leaching of Cu was found to occur in three stages. These stages consisted of direct acid leaching, bacterial oxidation and ferric iron leaching. These leaching stages can most easily he described through the examination of not only Cu dissolution but also Fe dissolution and its subsequent oxidation and precipitation. The p11 of the system was found to he critical in establishing and maintaining the bacterial leaching system. The oxidation potential was seen to he influenced by the leaching system as the oxidation states altered. Test variables such as, 02, COz, and temperature were all found to influence the system. Final copper recoveries were in excess of 90 per cent in each column test over a leach time ranging from 211 to 328 days. Given similar leach conditions are applied, the application of this technology to site is expected to give comparable results.

Jan 1, 1994

By Carras S, Kelsey P, Caccetta L

An important problem in open pit mine planning is that of detennining the optimum ultimate pit limits of the mine. These limits are that contour which is the result of extracting the volume of material which provides the total maximum profit while satisfying certain practical operational requirements such as safe wall slopes. The determination of the optimum pit contour provides information that is essential in the evaluation of the economic potential of the mineral deposit. A number of optimisation techniques are available for determining this contour with the Lerchs-Grossman and the Network Flow methods being the most favoured. Unfortunately, direct application of these techniques to large ore-bodies may cause considerable difficulties because of the computational time and storage requirements. In this paper, we present a strategy for resolving these problems, and the associated pit design software PITOPTIM (incorporating a fast network flow technique) and a data reducer, BOUND. The results presented highlight the speed and power of the software package rivalling the popular Lerchs-Grossman technique. An application of the software for a sensitivity analysis is also presented and discussed.

Jan 1, 1991