Search Documents

By N Barnett, M Dello-lacovo, J Oh, S Saydam, T Pelech

In-Situ Resource Utilisation and Off-Earth mining require the application of horizontal drilling. The stability of such openings is challenging when excavating in the lunar regolith. Excavations on the Moon will encounter unconventional operational conditions such as different material properties, low gravity, and a moonquake. Micro-tunnelling or drilling to support lunar exploration and development of infrastructure on the Moon requires stability analysis to ensure its desired performance. The discrete element method (DEM) modelling technique has been utilised to investigate the optimum opening sizes on the lunar soil. From the literature, the mechanical properties of the lunar regolith have been reviewed and used for numerical model development. The model has been calibrated by simulating numerical triaxial tests with the Mohr–Coulomb failure criterion. Then, detailed parametric studies have been performed to investigate the influence of confinement, opening dimensions and moonquakes on the stability of openings. The findings have led to the development of a simple stability chart of the relationship between unsupported opening sizes and lunar regolith properties at different depths.

Nov 29, 2022

In several of the States of Australia, mining on private property has been seriously hampered by the fact that large areas of land have been alienated from the Crown before the discovery of gold or other minerals. In Western Australia this difficultyhas only occurred to a small extent, and has largely been overcome by an act entituled "An Act to Permit Mining on Private Property, No. XXIX., 'October, 28th, 1898." Under this act, the holder of a miner's right can apply for a gold mining lease on private land; such applicant may treat privately with the owner of such land as to the amount of compensation to be paid for surface ,damage, or the case may be brought before the Warden who will assess the damages. Private land used as a garden, orchard, or vineyard is exempt from lease, unless the applicant has authority from the owner, or such lease is limited to a greater depth than 100 feet from the lowest part of the surface.No lease shall be granted of any mines under any private land in any municipality unless either the applicant has authority from the owner, or such lease is limited to a greater depth than two hundred feet from the lowest part of the surface.The same regulation applies to leases of private land on which any hospital, asylum, or public building is situated or under or within one hundred and fifty yards laterally of any...

Jan 1, 1901

By K A. Bunker, A D. Campbell, E Ah Mu, A R. Penney

The Ernest Henry mine is a transverse sublevel cave (SLC), which is relatively unique due to the 45 degree inclination of the orebody. To economically recover ore, each sublevel is horizontally offset from the previous level by around 25 m, depending on the orebody geometry. Mine development, slotting and initial production within this zone occurs in a high stress abutment that increases in magnitude at depth. These areas are seismically active and close to the hanging wall where cave propagation is yet to initiate. High stress conditions and the close proximity to the cave seismogenic zone results in challenging geotechnical conditions in the step out zone of each level and requires management of hazards including stress driven rockfalls, rock bursts and pillar failure.This paper outlines how these hazards were forecast using numerical modelling and geotechnical monitoring. Risk management techniques included dynamic ground support design, development of a new mine layout and extraction sequence as well as delayed re-entry into seismically active areas. Ongoing monitoring, instrumentation measurements and field observations were used to track the effectiveness of the controls.Future production levels are forecast to experience increasing stress and seismicity, which will increase demand on excavations and installed ground support. Ensuring the techniques and controls for monitoring, measuring and mitigating stress and seismic hazards are enforced is essential for continued safe production.CITATION:Campbell, A D, Bunker, K A, Ah Mu, E and Penney, A R, 2016. Managing stress and seismicity in an inclined sublevel cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 319–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Exploration risk increases with time, due to a general decrease in prospectivity as the more accessible deposits are found, and be- cause of rising costs and demands due to an improving standard of living. Risk is separated into financial risk, which increases sharply at the development stage, and the risk of failure which is at its peak at the outset of exploration. Risk is also divided into internal and external factors; some of the latter cannot be offset, viz. the systematic overall risk for any enterprise. The recently emergent risk embodied in withdrawal of large areas from exploration access is discussed. An appeal is made for objective multiple land-use policies to be applied so that land remains available at reasonable cost and with appropriate environ- mental safeguard conditions. Risks specific to gold exploration are discussed. As gold now accounts for over 50% of all mineral exploration, and most other metals are depressed, any sharp decline in gold will have grave effects on the ex- ploration industry. Gold exploration will become more difficult and expensive in about five years, after most of the readily accessible deposits in Australia are found. Government's role is important in pro- viding stability and basic data at reasonable cost. Exploration for specific minerals or of particular areas could be stimulated by extending the 150%.tax deductibility of R & D to aspects of exploration of strategic im- portance, particularly in the event of a downturn. Exploration is classic scientific research, at least through to the proving Stages.

Jan 1, 1987

Exploration risk increases with time, due to a general decrease in prospectivity as the more accessible deposits are found, and be- cause of rising costs and demands due to an improving standard of living. Risk is separated into financial risk, which increases sharply at the development stage, and the risk of failure which is at its peak at the outset of exploration. Risk is also divided into internal and external factors; some of the latter cannot be offset, viz. the systematic overall risk for any enterprise. The recently emergent risk embodied in withdrawal of large areas from exploration access is discussed. An appeal is made for objective multiple land-use policies to be applied so that land remains available at reasonable cost and with appropriate environ- mental safeguard conditions. Risks specific to gold exploration are discussed. As gold now accounts for over 50% of all mineral exploration, and most other metals are depressed, any sharp decline in gold will have grave effects on the ex- ploration industry. Gold exploration will become more difficult and expensive in about five years, after most of the readily accessible deposits in Australia are found. Government's role is important in pro- viding stability and basic data at reasonable cost. Exploration for specific minerals or of particular areas could be stimulated by extending the 150%.tax deductibility of R & D to aspects of exploration of strategic im- portance, particularly in the event of a downturn. Exploration is classic scientific research, at least through to the proving Stages.

Jan 1, 1987

Rheological Behaviour of Clay-Rich Gangue Mineral Dispersions During Hydrometallurgical Treatment Alumino-silicate minerals invariable may present an intractable challenge in hydrometallurgical operations employed in low grade nickel, copper and gold ore leaching or high level nuclear waste (HLNW) processing. The interactions and reactivity of alumino-silicate clay gangue minerals such as muscovite/sericite, chlorite, kaolinite and smectite under acidic (eg pH <3) or alkaline (pH >13) conditions can have a striking impact on the particle interactions. These may manifest in undesirable pulp rheology, poor extraction rates and challenges in the subsequent "handleability" and solid-liquid separation processes (eg dewatering). In the present work, a review of investigations involving the interfacial chemistry, interactions and rheological behaviour of aqueous dispersions of mica-group, layered alumino-silicate clay (muscovite / sericite) and chalcocite minerals as a function of pH in the range 2 - 9 and time at 25¦C, is presented. Particle zeta potential, reflecting interfacial chemistry, indicated a strong pH-history and particle volume fraction dependency. Pristine particles' zeta potentials measured from high to low pH indicated mineral-specific isoelectric point (iep) at pH range 2 - 5. Subsequent measurements from low to high pH showed pH-history dependency with iep shift to higher pH values, the extent of which also depended upon particle volume fraction and aging time. Pulp pH-mediated particle interactions revealed by shear yield stress analysis displayed a bifurcation behaviour and good compliance with DLVO theory. The maximum pulp yield values occurred at the iep whilst weak rheology was observed where the magnitude of the particle zeta potential was greatest. The pivotal role played by both pulp chemistry and suspension conditions in regulating the particle interactions and concomitant rheological behaviour is highlighted. The implications of the findings with regards to clay-base pulps' handleability and its control during aqueous processing are discussed.  

Sep 13, 2010

The history of mining is rightly proud of its achievements in improving productivity and cost improvements over the years. No matter what measure is used, tonnes per manhour, cost per tonne, etc vast improvements have been made over the last hundred years. In fact over the last ten years in Australian coal mines raw coal output per employee has increased by 60 per cent. When one examines why these improvements have taken place the principal reasons have been technological advancement in mining equipment, excavator and dump truck capacity increases, longwall and continuous miners continually improving in reliability and size. Of course all these improvements are correlated to an increase in capital cost. Even with the above-mentioned advances the pressure for increased performance is as strong as ever. The international mining and mineral-processing sector is currently operating in a recessive market with some traditional commodities, eg gold trading at 20 year lows. During recessive times senior management will demand greater returns on capital employed: the obvious choices being reducing costs or increasing throughput. In addition, head office environments will often place a capital freeze on operational management so the opportunity to take advantage of technological change is not available. The challenge is, therefore, to increase throughput and cut costs without the need for capital. The answer is to optimise the existing labour and plant. If done systematically a result in productivity improvement, in our experience, as high as 45 per cent can be achieved with the average across South East Asia and Australasia being 21 - 23 per cent. The intention of this paper is to present a systematic approach to labour and machine utilisation thereby gaining the greatest possible return on the existing capital base.

Jan 1, 1999

By P B. Hills, R J. Walton

Narrow vein tabular orebodies are prone to mining induced seismicity. The Tasmania Mine is a complex example of a seismically active tabular orebody, where the contrasting material properties of the host strata and of the orebody itself, serve to exacerbate the seismic response. Analysis of a continuous record of seismicity over a period of seven years has provided significant insight into the fundamental mechanics of the rock mass. Understanding seismicity to permit safe extraction of the orebody has been enhanced by instrumentation of rock mass behaviour in response to mining and mining induced seismicity. It is the purpose of this paper to explore that understanding in respect to the adoption of an alternative down-hole Avoca stoping method for use in particular circumstances.Intensive instrumentation of the Tasmania Mine over a period of four years has provided insight into the behaviour of the rock mass in response to extraction of the narrow vein orebody it encompasses. A range of instruments have been installed in clusters or single installations in order to measure changing stress conditions and the impact of those changes on the rock mass and the reinforcement system.Instruments are often installed in very close proximity to active production stoping. While it has been possible to observe the impact of the mining and mining induced seismicity at very close quarters, instruments installed in these locations are vulnerable to damage and consequently, the level of instrumentation is high. Instruments are continuously logged, typically on a six hourly basis coinciding with the end of regular blasting times. The response of the instrumentation to changed rock mass conditions is considered against the background of development and production blasting and against the seismic record to assess the viability of downhole Avoca stoping.CITATION:Hills, P B and Walton, R J, 2012. Continued observations of rock mass behaviour in response to stoping at the Tasmania mine, Beaconsfield, Tasmania, in Proceedings Narrow Vein Mining 2012 , pp 169-178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

The work described herein is the opening phase of an extensive system of underground excavation undertaken under contract with a Malayan authority.The specifications called for the lining of all tunnels in earth or broken rock with circular segmented cast iron lining, similar to that of the London tubes, and it is the installation of these linings which it is proposed to discuss.Owing to the long deferred delivery quoted and the obvious need for speed of access to the internal installation, it was decided to defer driving the completed circular section and substitute two small timbered headings.These could later be opened out in turn to full section and lined without prejudice to traffic, since both of them had access to the internal workings.NATURE OF ROCKThe rock series through which the circular sections were driven consisted of:(a) A wide zone of intrusive porphyritic granite, consisting generally of orthoclase phenocrysts in a ground mass of micro pegmatite. This area showed advanced weathering, varying from a stage showing slightly tinted kaolin containing approximately 20% of small boulders to one of ultimate decomposition to pure kaolin;(b) A narrow zone of weathered augite diorite, consisting of rock masses of a maximum weight of some 100-150 tons, isolated by clay seams up to 1 ft. 6 in. in width.The whole area was in a state of quasi-hydrostatic equilibrium, which resulted in heavy pressure immediately after excavation. Freshly broken faces would appear to be quite solid but, within a few minutes, would commence to sweat and "slab off" under pressure and, unless support was placed promptly, the whole face would burst out and run from above. Mucking was slow, owing to the plastic nature of the clay and the ease with which it puddled into slurry.In zone (b) a good deal of trouble was experienced because of the fact that the somewhat heavy blasting necessary tended to cause movement of the large rock masses. Subsequent scouring out of the supporting clay bands by the waterflow permitted settlement of the ground on to the timbers and many reinforcing sets were therefore required.The timbering of the pilot headings and its relation to the cross-section of the circular tunnels is shown in Fig. 1. Top and side spiling was driven in the ordinary way, but in bad ground intermediate sets and breast boards had to be placed. These sets were usually withdrawn after the...

Jan 1, 1941

The perception of the mining industry in the Australian community has changed considerably over the last four decades. This has been partly brought about by changing values and expectations of the Australian community as well as by global factors. The legal environment for the Australian mining industry has undergone significant changes. Among them, the High Court's Mabo decision which confirmed native title rights as part of the common law and environmental legal developments are dealt with particularly. It is suggested that the Australian legal environment is not necessarily the prime cause for Australian mining companies taking their investment off shore. This is a summary on how native title impacts on land tenements and some of the major issues that emerged since the `Mabo decision' and the Native Title Act 1993 are discussed. Environmental legal developments have resulted in liability facing directors and senior management in compliance matters .and in operating mining and other businesses because of changes in community expectations. In the next decade it is suggested there will be many drivers for more changes in the legal environment. Some of these are touched on including the changing roles of the Commonwealth and State Governments, the High Court as -law-makers and the changing relationships with indigenous people in Australia and in overseas countries. The changing legal environment for mining demands a national approach in many areas on the proposition that resource based industries are part of a national industry. The uniform law approach among the States has been taking place but this needs to further. An appropriate task force should be forward to review the entire legal structure and regulations affecting mining on a national rather than a State basis . The mining industry will need to work with expectations of a changing community which have powerful, but sometimes contradictory, interest groups.

Jan 1, 1997

Although the Diamond that is cut and polished and made up into an article of jewellery, is so well known, there are, comparatively speaking, very few outside the industry who know this beautiful crystal in the crude state, as turned out ofNature's laboratory, and the means employed in winning this precious stone.This article is written with the endeavour to give the reader some idea of the geological formations in which the Diamond occurs, and as it is reported that Diamonds have been found in Western Australia, as well as in other parts of the Australian Colonies, a few hints as to the means employed in working the ground in South Africa may be of use to those intending to prqsecute the search in this country. The general geological formation of the South African Diamond Fields is Lacustrine shales and sandstones, intersected by dykes of various eruptive rocks, varying considerably in their character. and in places vesicular in texture, the vesicules being more or less filled in with zeolites by permeating waters.

By G J. Lyman

In sampling a process stream, conventional sampling theory deals only with the variation of the analyte content and neglects the impact of the variation in the mass flow on the sampling variance, whether the sampling regime is time-based or mass-based. This is an obvious simplification of the real state of affairs and it is worthwhile to study this impact via simulation.With a facility to simulate large (long) random functions having some thousands of points in the function and the ability to impose covariance functions on the mass flow and analyte variations, such a study is possible. It is also possible to evaluate the impact of correlation between analyte content and mass flows.This paper describes a limited study of the variance increase due to mass flow fluctuations over the usual sampling variance due to analyte variation during the sampling period. The bias in the sampling result is determined for specific modes of correlation. Simulation methods are used as they are the only means by which a sampling result can be compared to the true assay for the lot; in the physical circumstances of mineral process analysis, it is never possible to determine the true process stream assay.CITATION:Lyman, G J, 2017. The impact of the weighting error, in Proceedings Eighth World Conference on Sampling and Blending , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By D Pearce

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

By Robinson KJ

Education in Australia now has to respond to a very wide political and policy agenda. The political emphasis is upon increasing participation and retention rates with a view to greater graduation rates in `high-tech' disciplines. There is an implied linkage between `education' and `economic well-being'. Our argument is that equalitarianism in education tends towards mediocrity. In this context many Geoscience educators view the future with pessimism. The argument is that science has been `sold short' and needs revitalising. We contend that Geoscience coursework should be a feature of both secondary and tertiary education in Australia. To this end we propose six policy initiatives to increase the content of Geoscience in education programmes.

Jan 1, 1989

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By K S. Park, J K. Kim, J H. Park, Y Su

The present study investigates the possibility of the direct removal of oxygen from the Ti-30Ni (wt per cent) alloy melt through the thermodynamic equilibrium reactions at 1623 K in the vertical tube furnace. The deoxidation efficiency of Ti-Ni alloy melt by adding different contents of metallic calcium (Ca) as a deoxidant was evaluated with the binary CaF2-MgCl2 flux. The thermodynamic equilibrium experiments showed that the total oxygen content in the alloy decreased from about 650 ppm to 350 ppm when 3.5 wt per cent Ca was added to the Ti-30Ni (wt per cent) alloy. Alternatively, the effect of flux composition in the CaF2-MgCl2 flux on the oxygen content was also investigated at 1623 K. Therefore, the effect of binary flux systems on the deoxidation ability was compared at 1623 K. According to the results, the flux system with 80 per centCaF2– 20 per centMgCl2 exhibited the best deoxidation capability, ie total oxygen content in the alloy reduced from 1450 to 550 ppm.

Aug 21, 2024

By Chung S

The problems associated with equating calculated and measured properties of explosives with blast results are examined. The results from six full-scale test blasts in a limestone quarry are described. The purpose of the full-scale trial was two-fold, i) assess the role of varying aluminum levels (10% maximum) in a given explosive in terms of blasting performance, and, ii) find correlation between calculated, as well as measured properties of explosives and the resulting blasting performance. Each blast consisted of 36 holes, initiated with short period detonators in a staggered 3-row 2.4 m x 2.7 m (burden x spacing) pattern. Each 75 mm diameter borehole with no subgrade contained on the average 22 kg of 65 mm diameter cartridged explosive. The bench height was 6.3 m, with an average collpr of 1.2 m. The calculated and mgasured properties of explosive included, strength, detonation and explosion pressure, VOD, plate-dent depth, underwater bubble and shock energy, and the total energy efficiency. Each blast was instrumented to measure detonation velocity, initiation sequence, muck pile motion by means of high-speed photography and blasting vibrations. The post-blast measurements included photogrammetric survey of muck pile for size distribution on surface, muck pile profile, as well as the extent of backbreak. The results showed that the overall blasting performance of the explosive in question was nearly commensurate with the level of aluminum in the explosive, and there was excellent correlation between the underwater test properties and the blast results. The study also exemplified the need for more extensive post-blast analysis than is usual practice, for quantitative assessment of blasting performance of explosives and providing the necessary data-base for calibration of blasting models.

Jan 1, 1990

A Sun SPARCstation based computer network is utilised to store and process mining data at the Macraes Gold Mine. Techbase and Medsystem software running on the SunOS unix platform is used to generate all data plans, sections and other design data required on a daily basis to run the mining operation. The Macraes site is regarded as a fully integrated site where all geological, grade control, exploration, orebody modelling, resource estimation, pit optimisation and mine design is undertaken on site by MacraesÆ professional staff. The methodologies employed are regarded as æstate-of-the-artÆ where computerisation allows the rapid and efficient evaluation of large quantities of mining data by a handful of professional personnel. Ore reserves are estimated using an indicator kriging method and roving cone pit optimisation, a complex process that would not have been achievable in pre-computing days.

Jan 1, 1992

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

A study of the accessory opaque iron-titanium oxide minerals of the Oiles Complex, central Australia, was an Important complement to an investigation of the magnetic properties of the Complex. These minerals constitute no more than 10 per cent of the rocks sampled, and generally less than 1 per cent of the ultramafic rocks ("magnetite" concentrations were not sampled for magnetic investigation).Titanomagnetite is the main opaque mineral present, although ilmenite exsolution has been widely developed. High-temperature oxidation of these produced mainly titanohematite, pseudobrookite and rutile. Both exsolution and high-temperature oxidation developed along specific crystallographic directions (along {111}), and in Irregular patches. Low-temperature oxidation is generally not well-developed, indicating the small degree of weathering in the rocks sampled.Although the Oiles Complex is layered, no apparent overall preferred orientation of the iron-titanium oxide minerals was observed, other than crystallographically controlled alignment of very fine grains within pyroxene crystals. Other textural features of the opaque oxides are restricted to symplectic intergrowths mainly with the ferromagnesian silicates.

Jan 1, 1971