Search Documents

By G Gibson, B Bessen

In coal preparation, large dense medium cyclones (DMC) at low pressure heads (typically 9D where D = cyclone diameter) are the norm. This contrasts with high density mineral applications where, largely for historical reasons, smaller cyclones at high heads are the standard. There are advantages in preferring large diameter cyclones at low heads, assuming that metallurgical performance does not suffer significantly. These include simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, reduced medium pumping demands, smaller buildings and overall lower capital and operating costs. In 2008, therefore, Xstrata Zinc decided to trial a single DSM-design 800 mm cyclone in one of its four DMC lines at Mt Isa, replacing the four 400 mm cyclones previously installed. Circumstances allowed a low head of 9.5 D to be trialled, compared with the existing 400 mm head of 21.5 D. This paper describes the trial, including tests using painted ore particles as tracers, estimates of yield and metal recovery, and wear monitoring. The larger unit performed well. There was no evidence that metallurgical performance in terms of metal recovery and waste reject rate suffered, and there was some evidence that it may have improved. Cyclone life increased, and preliminary data suggest that the replacement cost of the 800 mm cyclones is less than half that of the 400 mm units, and this is expected to improve. The plant layout and operability have also improved significantly. Xstrata has therefore decided to convert the whole plant to four low head 800 mm units, replacing the original 16 high head 400 mm units. The paper includes an explanation of the effect of static head on DMC separating force. It also reviews earlier research on diamond applications, and applies a general DMC process model to the Xstrata case, both of which confirm that large, low head cyclones are appropriate in mineral applications, contrary to conventional practice. Such units could significantly reduce both the capital and operating costs of DMC plants in mineral applications.

Jan 1, 2009

By A M. Purba and A Sjadat, A D. Wilson

Ongoing mining of the East Ertsberg Skarn System orebody below the Gunung Bijih Timur and Intermediate Ore Zone caves has been relatively successful and a ramp up to 80 000 t/d was achieved in the Deep Ore Zone Mine. However, the distribution of production, the overall drawpoint availability as well as the rate of change of the cave back profile has not followed the anticipated path. Several key factors influencing cave growth and progress, grade variation, fragmentation, wet muck and surface subsidence have been recognised over the life-of-mine that now have to be taken into account for planning the later stages of mining.The paper will discuss the influence of geological controls of lithology and structure – how this as well as other contributing aspects have impacted ore flow, contributing to some of the widespread panel damage, and been a key factor in compacted draw columns and caused an accelerated appearance of water ingress. This in turn has rapidly changed the distribution of wet drawpoints requiring remote mucking and special controls that also affect the call from the remaining dry drawpoints. Comment is also made on the potential final cave profile if it continues along the current trend and some discussion is offered about possible mitigation measures if this were to come about.CITATION:Wilson, A D, Purba, A M and Sjadat, A, 2016. Progressing cave performance into the later stages of the Deep Ore Zone mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 285–292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The InLine Pressure Jig represents a breakthrough in digging technology Its design incorporates a unique combination of features previously utilised in conventional jig design. In particular, a moveable screen and circular bed are used to excellent effect. However, a major design innovation is the encapsulation of the circular bed within a vessel - allowing the equipment to operate under pressure. This innovation eliminates free water surface, improves the dynamics within the separation layer (crossflow) and provides significant cost savings in the handling of slurries. Recent research results have indicated its capacity to achieve high recoveries and upgrade ratios in the gravity separation of Minerals.

Jan 1, 1997

The status of remote sensing data availability in New Zealand is outlined and discussed. Currently, two multispectral remote sensing satellites are providing regular data over New Zealand; aircraft scanner services are available from Australia.; operational radar satellite services are yet to materialise. The advantages and disadvantages of the various data types are compared and contrasted. Some image processing considerations are outlined.

Jan 1, 1993

By McNicol M. D

Petroleum exploration in onshore Gippsland was directed in the 1950s and 1960s towards plays in the basal Latrobe and Strzelecki Groups, but these became forgotten in the 1970s with the Latrobe play discoveries offshore. The principal explorationists of the time were Woodside Oil and Arco Ltd, who then departed the scene after drilling some 18 wells without major success. In the late-1980s successful hydrocarbon finds in equivalent age Otway Group sediments in the Otway Basin were made and in early 1990 Tyers Petroleum began investigations into Strzelecki Group prospects as applied to the onshore Gippsland Basin. Some 18 anticlines have been mapped, based on shallower coal exploration drilling in the Latrobe Group, which from seismic and gravity evidence are believed to unconformably overlie similar anticlinal structures in the underlying Strzelecki Group. Strzelecki targets of interest within drilling depth are the basal Tyers Conglomerate/Rintouls Creek Sandstone Formations which outcrop in the north of the Latrobe Valley and are analogous to the Pretty Hill Sandstone in the Otway Basin. In addition, intra-Strzelecki Group targets similar to Heathfield and Windermere Sandstone Members are also considered to be present. Good source rocks are abundant including coal seams and carbonaceous sediments of Neocomian and Jurassic age, which lie within the oil window. Seal is provided by the overlying Aptian-Albian aged volcanogenic sediments. The Tyers/Rintouls sandstones - a target in the Woodside/Arco wells, with two exceptions, were not reached. Encouraging intra-Strzelecki shows were reported in many of the wells. Basal and intra-Strzelecki porous quartzose sandstones remain one of the few untested plays left in the Gippsland Basin and, in the onshore, merit extra attention as they he within the oil window at economically drillable depths.

Jan 1, 1992

B. P. Thomson (South Aust. Dept. of Mines): Dr. A. B. Edwards presents in the published discussion on the above paper, his interpretation of the dolerite dyke-lode relationship as a major objection to the syngenetic origin for Broken Hill ore bodies to which Mr. Condon subscribes.Dr. Edwards claims that the dyke-lode relationships indicate clearly that the Broken Hill orebody was formed after the folding and regional metamorphism of the Willyama Series. Field evidence compels m:e to join with H. F. King (1958), in finding this conclusion unacceptable-as follows:(1) Broken Hill type mineralization, as defined by King and Thomson (1953), is clearly confined by the regional sillimanite isograd and does not extend into the lower temperature almandine and biotite zones as does the Thackaringa type mineralization.(2) In the Corruga area the writer has mapped a dolerite dyke apparently cutting a conformable quartz gahnite lode of the Broken Hill type (see Edwards 1958, p. 12).(3) At the Champion mine a similar lode is cut by a fine grained granite dyke.An alternative history of the dolerite dykes to that given by Stillwell & Edwards (1956, p. 26) appears possible. It has been suggested by the writer in an unpublished thesis, (Thomson 1955, p. 30), that the pyroxenite and serpentine plugs and dolerite dykes are rheomorphic end-products of a complex regional metamorphic and metasomatic process involving the formation of amphibolite and pegmatite. The analogy in composition between the dolerite and normal amphibolite is close (see Edwards 1958, Fig. 1, p. 22).

Jan 1, 1959

By J B. Gemmell, D R. Cooke

Recent mapping at the Kelian epithermal gold deposit in East Kalimantan, Indonesia has delineated intrusive and extrusive-phreatomagmatic breccias, their magmatic roots, and late-stage endogenous domes of a maar-diatreme complex. The Kelian epithermal system is characterised by a wide variety of mineralised and unmineralised breccias, which include tectonic, hydrothermal, phreatic and phreatomagmatic varieties. Phreatomagmatic breccias and associated igneous rocks post-date early stage alteration and mineralisation, and pre-date main stage precious and base-metal mineralisation. This study emphasises the spatial, temporal and genetic links that have been drawn between diatremes and both epithermal and porphyry systems in volcano-plutonic arcs.

Jan 1, 1999

A review is made of the limited published experience of the effects of cemented fill in flotation.A general approach is adopted in listing and discussing possible sources of, and reasons for, ore contamination by cemented fill, together with basic, fundamental approaches to minimizing this contamination. These approaches involve basic mining design, effect of fill placement density, optimization of curing time and of cement content, variation of fill particle grading, use of flocculants and of pozzolans, fill placement and dewatering, and or blasting and handling practice.

Jan 1, 1974

A drive, 3,500 ft long, was planned to explore mineralization exposed by diamond drilling. A rate of advance of 150 ft per fortnight, approximately double previous Broken Hill rates, was required. Subsequent to the completion of this drive its extension for a further 6,200 ft was planned to provide a main haulage way along which ore could be transported from a newly acquired lease back to the main hoisting shaft, a total distance of 13,500 ft.This paper describes the working conditions, relationships, manning and costs, and gives details of the cycle and equipment used to achieve rates up to 170 ft per fortnight.OBJECTIVEDiamond drilling from the 1,000 ft level at the Delprat Shaft section had indicated that the zone of mineralization, about 150 ft wide, which had been explored on the 1,000 ft level for a length of 2,600 ft, continued downwards with a westerly dip. The drilling results showed that within this wide zone there were arrower lenses of mineralization of possibly payable grade (see composite plan, Fig. 1).Diamond drill holes of 2,000 ft and over, particularly through heavily sheared areas of sericite schist, had been found to be costly, slow, and inadequate in testing the potential and trends of these smaller concentrations of mineralization.It was therefore decided that an exploratory drive should be advanced from the northern limit of the 1,480 ft level into the western mineralization, and that from this drive diamond drill holes should be drilled at dose intervals to outline the ore.The 1,480 ft level was chosen for the following reasons.1. It had the greatest northerly reach of the accessible levels at No. 7 Shaft section below the 1,000 ft horizon and therefore would enable the test to be made most quickly.

Jan 1, 1965

Alluvial gold was found in the Terawhiti area, West of Wellington, in the 1850s. This led to the discovery of reef gold. Periods of minor 'gold fever', company flotations, and mining activity occured between 1869 - 1973, 1881 - 1986, and in the late 1880s, with one final company active in 1911 - 1914. 1n the early 1980s, further field work was carried out. No viable mining operations resulted from any of this activity.

Jan 1, 1993

Vatukoula is credited with the second largest population in the Colony of Fiji. Within an area comprising 550 acres are living approximately 4,500 people. Of these, about 1,150 Fijians, 90 Rotumans, 90 Europeans, 180 Part-Europeans, 180 Indians and 30 Chinese and miscellaneous Pacific islanders are employees of the Associated Mining Companies.The remainder is made up of employees dependants with a small minority of tradespeople and Government servants, such as storekeepers, school teachers, police and post office officials.To appreciate fully the work involved in the administration of this unusual community it is necessary firstly to know something about the various types of people which compose it.The FijiansAlthough the Fijians are of Melanesian stock their physical characteristics indicate a Polynesian strain. Natives from all provinces in the Colony are to be found in Vatukoula and their varied types point to this MelanesianPolynesian intermixture. For example, there are people from Lau** and Kadavu who are tall and well built with good features and comparatively fair skins contrasting with the dark, broad featured and generally short people of the hill tribes of Ra and the coastal tribes of Bua.The Fijians, particularly the older people, are noted for their dignity, courtesy and hospitality. The young Fijians of the present generation, large numbers of whom are...

Jan 1, 1953

By Dawson RD

For the past 45 years, the casting of refined lead ingots by The Broken Hill Asso- ciated Smelters Pty. Ltd. (B.H.A,S,) at Port Pirie has been mainly by use of manually operated rotary casting wheels of Newnam design. This style of operation was quite satisfactory as far as standard of product was concerned, but was manually intensive and a relatively high cost operation. With most other large scale lead producers already using automated-casting equipment, an investigation which commenced in 1966, progressed through stages of enquiry, design and development until the present plant commenced trial operations in late 1973, and fully operative in late 1974. While certain features of the plant are sed on overseas practices the plant was signed and built within Australia to BRAS ecifications. As constructed it consists two almost identical casting lines each pable of producing 25 kg ingots at 25 tonnes r hour using straight line casting machines d automated stacking weighing and strapping

Jan 1, 1975

By A Liu, T Ren

Gas explosion in underground coal workings can pose a serious threat to the safety of mine workers and the entire mine operations. Gas explosion is a very complex thermal-chain reaction in a confined underground environment. Based on combustion and explosion theory, three dimensional (3D) computational models were developed to simulate mine gas explosion flame and overpressure wave propagation in a single entry gateroad in underground coalmines. Six different explosion scenarios were modelled and compared with large scale experimental results and AutoReaGas simulations. Model validations show that the use of shear-stress transport (SST) k-? model together with eddy-dissipation model (EDM) produces good agreement with both experimental and AutoReagas simulation results. Modelling results demonstrated that the changes of temperature versus time can be divided into four stages, ie the initial condition stage, and periods of warm-up, active burning, and burnt-out. Assuming a limited volume of methane is involved in the explosion, the maximum temperature decreases as the distance increases from the explosion point, with the highest temperature reaching about 2460 K. Modelling results show that the evolution of the explosion flame shape experiences four typical stages, ie spherical flame, finger-shape flame, flame with the skirt touching the side walls (ribs) and tulip flame, which are similar to the pattern of a duct explosion. The pressure in the gateroad remains the same as the initial value before the arrival of the explosion wave and then increases rapidly to the maximum value. Modelling results from this study will be used for the design of explosion arresting devices and mine seals in underground coalmines.CITATION:Liu, A and Ren, T, 2017. Computational simulation of gas explosion and its propagation in single entry gateroad, in Proceedings Australian Mine Vent Conference 2017, pp 181–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

Flue dust from the sintering of base metal sulphides was leached to remove cadmium and arsenic. Leach liquor contained cadmium, zinc and small amounts of other base metals as chlorides. Results are reported of the use of a cation exchange resin Zeocarb 225 to separate the base metals from the arsenic. The resin was eluted with sodium chloride or sulphate to give a solution of relatively concentrated cadmium suitable for recovery by zinc cementation. The limited solubility of sodium sulphate presented some practical problems which were investigated. Another problem was the precipitation of lead sulphate in the resin during elution.INTRODUCTIONWhen lead-zinc sulphides are sintered prior to smelting, the gases passing to the flue are mainly uncondensable but contain a certain proportion of sublimates and dust particles which deposit in the flue or are carried, after condensation in the gas stream, to some form of dust extraction equipment.The recovered dust is a complex mixture of base metal sulphates, sulphites, sulphides, chlorides and oxides, the composition depending on the original concentrates. A large proportion of the cadmium and some of the arsenic originally in the concentrates finds its way to this flue dust, the treatment of which can be a convenient means of removing these elements and controlling their concentrations in the main lead-zinc smelter circuit. However, disposing of this material represents an appreciable waste of base metals as well as a serious toxicity hazard.Sulphide Corporation Pty. Ltd. was faced with this problem in planning the flow sheet of the new lead-zinc smelter at Cockle Creek, N.S.W. From a test run carried out on a pilot plant at Avonmouth, U.K., using a mixture of lead and zinc concentrates, a sample of dust was obtained for...

Jan 1, 1960

By H M. Ahmed, W S. Dunbar

Construction of cave mining systems requires significant capital expenditure and long-term commitment of human, equipment and material resources before production commences. Risks and uncertainties of these large-scale mining projects are significantly higher than for small-scale projects. This is due to the complexity and interactions of the construction schedule components and the large scale and uniqueness of such projects. One way to successfully manage construction uncertainties that would lead to schedule delays is to include a reasonable cost contingency in the budget estimation. A real options approach based on the least-squares Monte Carlo (LSM) method is used to estimate cost contingency associated with schedule uncertainty in mass mining projects. Cost contingency is estimated as the cost of potential project crashing (acceleration) decisions, which pays for not extending the schedule. While such a significant undertaking is expected to be subject to some delays, these can have an enormous impact on the economic value of such projects. The value of the crashing option was explicitly formalised into the process of valuation, as it is assumed to be a single option being considered in the valuation at every decision point prior to the construction completion date. As a part of the proposed method, a stochastic function for the percentage of remaining scope of work for the remaining duration of the entire project was integrated into a framework of numerical simulations. This ensured that this function can implicitly account for sources of schedule uncertainties for projects represented by multiple and overlapping work packages. The LSM method was applied to a real case scenario in an operating block cave mine, with modified scale and features. The results yielded by the LSM method indicated that significant changes in capital budget allocation stem from variation in a contractor’s risk perception and confidence level of estimated delays.CITATION:Ahmed, H M and Dunbar, W S, 2016. Budget estimation and contingency allocation of block cave construction using least-squares Monte Carlo real options, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D G. Miljak, J Khachan, B K. Schwitter

The performance of prototype magnetic resonance sensors suited to mineral measurement in conveyor, slurry or portable applications is described. The sensors can be positioned around conveyors and modified slurry pipes, providing deep penetration of the sensing field, relative insensitivity to ore surface conditions and high mineral discrimination. Measurements on slurry, concentrates and ores sourced from mine operations are presented for two applications. Firstly, the quantitative measurement of chalcopyrite in slurry was demonstrated in laboratory measurements. In a calibration test, a standard error of 0.1 wt per cent and detection limit of 0.3 wt per cent was obtained. Secondly, results were obtained for the discrimination of iron ore texture. Signals were readily observed using measurement integration times of seconds to several minutes, depending on ore material. The results demonstrate the feasibility of online quantitative analysis of selected minerals in processing applications using magnetic resonance.

Jan 1, 2008

Uranium ore at Sleisbeck, N.T., occurs as lenticular bodies associated with zones of bleached carbonized schists lying between walls of closely folded quartzite. The ore consists mainly of uranium micas with Borne pitchblende.INTRODUCTIONThe Sleisbeck uranium prospect is about 70 miles E. of Pine Creek, and 160 miles S.E. of Darwin (Fig. 1). The prospect consists of a well-defined, E.-W. trending line of hills, about I! miles long. The line is composed of 3 major hills called the Eastern, Central and Western hills, with minor interconnecting hills and outcrops (Fig. 2).

Jan 1, 1955

By Bohrn W, Milionis K, Tessmer G, Reidetschlager J

The share of electric arc furnace based steel production is increasing - New technologies for the production of virgin raw materials for EAF production are under development and on the market - VAI has a strong position in the field of scrap substitution technologies with their COREX«-, COREX«-DR and FINMET«-technology. In late-1998 the steel plant SALDANHA was started up successfully. This integrated compact mill is using the COREX«-technology as hot metal and a combined DR-plant as DRI production unit. Also in 1999 the BHB FINMET« plant Port Headland went on Stream.

Jan 1, 1999

Competition in the mining industry is the main driving force for both equipment manufacturers and end users to develop and apply the most cost efficient solution to a mining problem. Therefore the challenge to find new solutions is usually met by several suppliers under various factors of influence affecting specifications. Time and timing are particularly important, but all new developments ultimately have to successfully perform on site.Consideration of all aspects of planning, manufacturing, user liaison and ultimate satisfactory commissioning hinges on the necessities of assessing of all the expectations in the mining application and the requirements of the concept and layout team. To apply the maximum available technical competence with solid thorough workmanship is the best possible foundation for success of underground machinery development.

Jan 1, 1991