Search Documents

By Cox SJD, Kramadibrata S

One of the major causes of accidents and loss of production in underground mines is falls of ground.As mines go deeper, higher stresses are encountered and strain energy stored in the rocks is more likely to be released dynamically. This results in bumping in the rock mass around a stope or development face. Such noises and increasingly difficult ground conditions are obviously a warning of more serious problems ahead. The activity is collectively referred to as rock bursting.In Australia the mining of metalliferous deposits is taking place at increasing depths at Mt Isa, Broken Hill and the Eastern Goldfields and ground control problems with rock bursts has already been experienced at all three sites.

Jan 1, 1990

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

By A A. Struthers, A D. Farmer

Power ultrasound may be applied to enhancing the processing of minerals. The enhanced performance is achieved through the very localised high-energy release at the mineral surface from the collapse of cavitation bubbles produced by power ultrasound. This gives rise to two effects: initially, the rapid cleaning of mineral surfaces û of oxidation products and coatings of fine adhering gangue minerals û and the attenuation of the boundary layer at the mineral surface during leaching, which allows fresh leachant to contact the surface more readily. Work carried out at CSIRO in conjunction with Tiwest Joint Venture has demonstrated that it is feasible to apply ultrasound to the leaching process in order to enhance the removal of contaminating minerals. When applied to the production of synthetic rutile from reduced ilmenite produced by the Becher process, the use of ultrasound proved beneficial to both the aeration and the final acid leach process. The effect of ultrasound was less marked in the case of the aeration process, once the method of introducing and dispersing the air was optimised. In the subsequent acid leaching step of the Becher process it was found that the application of power ultrasound could reduce leaching time to about one quarter of the time required when only agitation was employed. Projected capital and operating costs, based on currently available commercial equipment, are also presented, and indicate that the use of ultrasound is commercially as well as technically feasible.

Jan 1, 2001

Human-caused global warming has become the environmental cause celebre of the early 21st century. The strong warming alarmist camp currently includes the United Nations, most Western governments, most of the free press, many large corporations (including Enron, before it failed), the major churches, most scientific organisations and a large portion of general public opinion. This phalanx of support notwithstanding there is no scientific consensus as to the danger of human-induced climate change. There is, therefore, a strong conflict between the level of public alarm and its scientific justification. How can this be? In a democracy, the media serve to convey to the public the facts and hypotheses of climate change as provided by individual scientists, governmental and international research agencies, and NGO and other lobby groups. In general, the media have promulgated an alarmist cause for climate change; they have certainly failed to convey the degree of uncertainty that is characteristic of climate science, or a balanced summary of the many essential facts that are relevant to human causation. Climate change is as much a geological as it is a meteorological issue. Natural climate changes, both warmings and coolings, are indeed a societal hazard. We usually deal with geological hazards by providing civil defence authorities and the public with accurate, evidence-based, general information about events like earthquakes, volcanic eruptions, tsunamis and floods, and then by adapting to the effects when a damaging event occurs. As for other major natural disasters, the appropriate preparation for extreme climate events is to mitigate and manage the negative effects when they occur, and especially so for dangerous coolings. Attempting instead to æstop climate changeÆ by reducing human carbon dioxide emissions is a costly exercise of utter futility. Rational climate policies must be based on adaptation to dangerous change as and when it occurs, and irrespective of its sign or causation. The issue now is no longer climate change as such, the reality of which will always be with us. Rather, the issues are, first, the failure of the free press to inform the public about the true facts of human-caused climate change and of the dangers posed by natural climate change. And, second, the vested interests held by many of the groups of warming alarmists. These interests include not only the obvious commercial ones, but also the many scientists and science managers who have discounted or remained silent about the huge uncertainties of the human-caused global warming hypothesis because it suited them to do so. Public opinion will soon demand an explanation as to why experienced editors and hardened investigative journalists, worldwide, have melted before the blowtorch of self-induced guilt, political correctness and special interest expediency that marks the sophisms of global warming alarmists.

Jan 1, 2007

By O J. Restrepo Baena, S Nowosad, R Webber-Youngman, N Mojtabai, P Foster, A Binder, S Hazuria, erson, S Raval, L Liu

As the mining industry faces times of change, new challenges arise to ensure raw material supply for the younger and future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net zero requirements for improving long-term operation performance, technological advancements such as automation and digitalisation, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields leaving mining engineering as one of the less preferred career options between the younger generations. Nonetheless, it is essential to continue addressing and supplying the skill sets that is suited to contemporary and future of the mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, up skilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more

Sep 1, 2024

By Corrans I. J

A wide variety of copper-bearing gold ores exist throughout the world which have yet to be processed economically for gold recovery. The copper minerals present in these ores can be many and varied and usually result in high cyanide consumptions and problematical levels of copper in leach solutions. The copper content is often assessed as being of nuisance value as the ores are generally of the grade or type which can support neither a copper project nor a straight gold project, due to the interference of copper. Many of these problematical gold-copper ores could possibly be processed economically for gold recovery using a novel ammoniacal cyanide leaching system which utilises a copper-ammonia-cyanide complex as an effective lixiviant for gold, yet limits copper dissolution and conserves cyanide. Results from recent testing have promoted a re-evaluation of the economics of treating some gold-copper ores. This paper describes the novel leaching process and discusses the conditions employed to treat a variety of gold-copper ores.

Jan 1, 1992

By M Devia, J Rapkoch

This paper is intended to help design engineers, operating staff and plant managers understand the principles of metallurgical gas handling systems design. It also explains operating, safety and energy savings issues that the designer should take into consideration in the design of process off-gas systems for sulfide smelters. Primary smelting reactors, converters, and other off-gas sources impose challenging duty requirements on the various components of the gas handling systems. This paper reviews the design of common system components including the hood for gas capture at the system inlet, gas conditioning, gas cleaning, ductwork, dampers, hot gas fans, and the appropriate use of instrumentation and controls. The engineer must also be aware of how ductwork system effects and heat losses influence system performance. Also, the analysis of a recently-designed gas handling system will be reviewed, which includes high-strength SO2 gas from a smelting reactor, asymmetrically located Peirce-Smith converters, and a gas mixing chamber to mix the gases before they are sent to two acid plants of different sizes.

Jan 1, 2005

In an earlier paper(l) details of a laboratory method of extracting and separating tantalum and columbium oxides from tantalite have been given. In view of the fact that Australia may have need to be self sufficient in this field it was decided to erect a pilot plant for the production of tantalum oxide in the Metallurgy School, University of Melbourne. The plant was designed for treating about 40 lb. of ore in a batch over a period of two weeks, although; because of the sectionalized nature of the process, the capacity of the plant was 40 lb. ore per week.Australia is fortunate in possessing some very rich tantalite and columbite deposits, particularly in the Pilbara District in Western Australia. The ore used in this work was obtained from a small but high grade deposit near Greenbushes, Western Australia, and consisted of lumps, weighing up to 8 lb. each, of almost pure ferro-tantalite with occasional thin veins of the very' rare' mineral stibiotantalite.The main constituents were:

Jan 1, 1946

This paper reviews the development and operation of a small underground tin mine in NE Tasmania. Tin mineralisation was discovered in the Lottah area in the 1880's with early alluvial and eluvial workings leading to the development of large low grade open pit operations. Apart from short lived activities operations ceased in 1915. Intensive exploration in 1978-81 outlined substantial tonnages of low grade tin mineralisation (0.2% Sn) of open pit material. An underground ore body was also located (800 000 tonnes 0.6% Sn). Spectrum Resources Australia Pty Limited acquired a 98 percent interest in the property in 1988. Mine and mill development began in early 1989 based on an underground mine utilising trackless mining using room and pillar with fill stoping. The milling circuit involves primary jaw crushing, Barmac secondary crushing to lmm, Mogensen and DSM screens with jigs and tables to make a wet concentrate. Final tin concentrates are produced by high tension and magnetic separation. Planned production rates are 500 t/day with a mine life of 6-7 years.

Jan 1, 1990

By A R. Penney

Since mining-induced seismicity first became apparent at the Beaconsfield Gold Mine in 2002, there has been an ongoing program of geotechnical investigations to understand the phenomenon and allow for the development of strategies to manage the risks it posed to personnel, the business and the community at large. Studies resulting from a seismically induced rockfall on Anzac Day 2006 have been extensive, and have advanced the understanding and management of seismicity at the mine. Enhancement of the mineÆs seismic array, implementation of extensive monitoring of ground behaviour, improved ground support and reinforcement design, and ongoing numerical modelling provide a technical framework for the management of seismicity. In addition, extensive involvement of the workforce in risk assessment and the development of standard work procedures (SWPs), has contributed to a æbest practiceÆ approach to manage seismic hazards at the mine.

Jan 1, 2008

By L Reynolds

Oceana Gold (New Zealand) Limited (OceanaGold) has commenced mining operations at the Globe-Progress mine in the Reefton Goldfield, an area that historically produced 2.1 million ounces of gold from underground quartz lode deposits. During the construction phase of the operation, advanced exploration programmes targeting near-mine prospects commenced. The focus of this ongoing exploration is the discovery of near surface, refractory gold deposits that are amenable to open-pit mining methods and treatment through the Globe-Progress process plant.   One such discovery is the Supreme deposit, located along strike approximately 3 kilometres to the south of the Globe-Progress mine. The Supreme area was tested extensively with diamond drilling in 2006, defining a deposit with similar mineralisation styles and grade to the Globe-Progress deposit. The mineralisation comprises a central core of gold-bearing quartz veins, locally containing visible gold, surrounded by a more extensive halo of refractory, disseminated gold associated with an arsenopyrite-pyrite sulphide mineral assemblage. Three subparallel mineralised structures host the mineralisation. These structures are highly oblique to the country rock orientations, extending approximately 250 metres along a northeast-southwest strike and at least 220 metres down-dip, with an average thickness of 12 metres and moderate dip to the southeast. Records of historical workings indicate that mineralisation extends further down-dip and remains open at depth. 5175 ounces of gold were mined historically at the Supreme deposit. OceanaGold have defined an Inferred Resource for the Supreme deposit of 0.84 million tonnes at 1.46 grams per tonne for a total of 40 000 ounces (at a 0.8 grams per tonne cut-off). Higher-grade zones of mineralisation exist within the deposit and further drilling is planned to test the extent, continuity and geological controls of the mineralised structures.

Jan 1, 2007

The oxidation of sulphide minerals in aqueous suspension is discussed from several viewpoints. Limitations of our present knowledge are pointed out, and several points where further information would be of special interest are mentioned.Firstly, some properties of minerals and their effect on oxidation are discussed. Properties of different species, such as crystal structure, lattice bonding, and "metallic" properties are mentioned, and then the effect of variation within a given species is discussed. The effect of physical factors, especially particle size, is also considered. Other variables discussed include the importance of solution composition, and its effect on the nature and rate of reaction, and the use of various oxidising agents. Some factors concerned with the whole system, such as temperature, pulp density and stirring rate are then considered.Finally, the nature of various oxidation products is discussed with reference to the kinetics of reaction and the nature of the rate limiting step. It is suggested that more attention should be paid to electrochemical explanations of the reaction mechanism.INTRODUCTIONKnowledge of the factors governing the rate of oxidation of sulphide minerals in aqueous suspension is a prerequisite for the effective control of many ore treatment operations. Rapid oxidation of sulphides is usually desired during the leaching of sulphide ores and concentrates, but in the cyanidation of gold ores, or in the leaching of uranium ores, any oxidation of sulphides may be regarded as an undesirable side reaction. Knowledge of many of the factors involved is also of interest in connection with the oxidation of sulphides in flotation circuits and in natural ore forming processes.Systems for which some reasonably quantitative data have been published are listed in Table 1. Qualitative...

Jan 1, 1961

Sampling systems are never perfect. They all have some bias and give variable sampling errors. The ways of thinking about bias and precision should be different before and after construction (or reconstruction) of a sampling system. Before a sampling system is constructed, the fundamental error variance can be estimated using GyÆs formula or by doing test work on the material to be sampled. The component of sampling variance which varies with the number of sample increments can be computed for the expected patterns of grade variation. The smallness of the bias can be checked using discrete element modelling, by checking that the proposed design complies with clauses in standards, or by copying an existing sampling system that performs well for similar material. After a system has been constructed, sampling precision can and should be monitored directly. Anyone claiming to take responsibility for a sampling system should know its precision. Bias could be checked by comparison to a more accurate sampling system, such as stopped-belt sampling, under conditions where bias seems most likely. However, it is more practical to conduct regular checks that the system is still operating as designed, that the design is still appropriate despite any changes to material flows, and that sample masses are consistent with the correct operation of the sampling system. If precision is not regularly assessed then it should be assumed to be very poor. If a sampling system is not regularly inspected then it should be assumed to be biased.

Jan 1, 2008

The Bellambi Coal Company Limited com menced longwall mining at South Bulli Colliery in 1965. At present it operates three long- wall units in two seams. Although results to date have been less successful than planned, it is apparent that this type of mining has tremendous potential in the particular conditions at South Bulli. Massive sandstone strata above the Bulli seam is the controlling influence on face conditions. The earliest equipment proved to be inadequate and the Company has progress- ively replaced and upgraded the roof supports and ancillary equipment so that the present units are capable of producing high and consistent outputs.

Jan 1, 1976

A major high grade zinc deposit, Dugald River has fine-grained and complex mineral associations which provide considerable metallurgical challenges for both mineral dressers and downstream processors. A long history of metallurgical testing focusing on mineralogy and flotation concentrate production has shown that while separate lead and zinc concentrates can be produced at saleable grades, high levels of iron, and particularly manganese, are likely to place constraints on the marketing of zinc concentrate produced from deeper zones where coincidentally lode development is at its maximum. Testwork has focused on characterising the flotation response of ore types ranging from banded and stringer sulphides to brecciated ores in a variety of sulphide matrices. A high level of variability with lower than expected metal recoveries has been indicated across some of the higher grade brecciated ores. However, the dominant slatey breccia has generally provided the best results. Heavy media preconcentration testwork has been moderately encouraging and at this stage, although value adding downstream of concentrate production on-site is not seen as an economic option processing developments are being monitored on a broad front. Providing satisfactory means can be developed for handling manganese during downstream processing of the concentrate, it is not difficult to see a world-class operation emerging from the resource in the medium-term Future.

Jan 1, 1993

By Oxenford R. J

An important rutile-ilmenite-zircon bearing sand deposit was discovered by local farmers at Eneabba, 300 km by road north of Perth in 1970. These heavy minerals occur in a series of ancient strandlines and associated dunal deposits at elevations from 85 m to 170 m above the present sea level and are situated,30 km inland. The strandlines were deposited on wave- cut platforms in an ancient bay bounded by Mesozoic sediments during a series of regress- ions from a high sea level, probably during late Tertiary or early Pleistocene times. The immediate source of the heavy minerals in the Eneabba deposit is a widespread low content of those minerals in the nearby Mesozoic sedi- ments. The high-grade southern portion of the Eneabba deposit has been closely drilled and is now being prepared for production by Allied Eneabba.Pty. Ltd., a subsidiary of Allied Minerals N.L. This part of the deposit is 11 km long and up to 2.5 km wide. It is characterised by little or no overburden and the average depth of mineralisation, bounded by a 2.5 per cent heavy mineral cut-off, is 12 m. The water-laid strandline deposits at the base of the mineralisation are generally high grade, ranging from 20 to 60 per cent

Jan 1, 1973

Cyanide-extractable gold is far more meaningful in the definition of ore, and control of extraction, than fire- assayable or aqua regia digestible gold. The use of cyanide- extractable gold addresses the significant problems of over- as well as under-assaying by fire and aqua regia digests. The problems of conventional control or diagnostic cyanidation extractions: lengthy extraction, and masking by pregrobbing in cyanidation extractions for assay purposes; are surmounted with a novel activator - Leach WELL. Full extraction of liberated gold, insignificantly affected by preg-robbers, can now be achieved within 30 minutes. This can assist in reducing common gold losses presently often hidden by inappropriate mine call factors, and/or high grade cut values. This paper includes a discussion of fundamental mechanisms of cyanidation, preg- and assay-robbing, which underlie the phenomena Involved.

Jan 1, 1992

By Kershaw M. G, Maughan R. C A

A process for eliminating nickel from electrolytic zinc plant solutions by precipita- tion with dimethylglyoxime (DMG) was developed to enable the Electrolytic Zinc Company of Australasia Limited (EZ) to treat nickel-bearing zinc dust precipitates. These precipitates are leached to recover their Cd and Zn content. The final Zn bearing solutions contain relatively high Ni concentra- tions (20-100 mg/1) and are treated with DMG and then neutralized to pH 4.6-4.8. The pre- cipitate is filtered off and the solution returned to circuit. DMG consumption is about 200% of theo- retical requirement, and Ni removal is 80% complete overall.

Jan 1, 1977

By T W. C Stambolie

Longwall mining is a form of underground mining and the principal extraction method for underground coal mining in Australia. The method is used in the mining of both thermal and metallurgical coal. The primary market for thermal longwall mines is that of the export market where price is governed against the Newcastle Thermal Benchmark index (globalCOAL, 2016).Australia’s thermal coal export outlook is considered moderate due to slower demand from major importing countries, as well as slowing domestic production. However, ‘Australia is projected to increase its share of world thermal coal exports and become the world’s largest exporter over the medium term as lower prices, increased domestic use and infrastructure constraints limit growth from other key suppliers’ (Office of the Chief Economist (OCE), 2016, pp 25, 58). On the contrary, and as a result of current global coal price trends, the basic economic principles of underground longwall coal mining are heavily stressed. From a life-of-mine perspective, influencing return on investment is at its greatest during project evaluation and execution. Appropriate and realistic economic assessment is paramount to ensuring the right outcomes are achieved under the current economic challenges.CITATION:Stambolie, T W C, 2016. Thermal coal industry – is longwall mining currently a life-of-mine option in Australia?, in Proceedings Life-of-Mine 2016 Conference, pp 57–61 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016