Search Documents

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986

Two structurally and mineralogically distinct sulphiderich veins cross-cutting the disseminated sulphides of the Nairne Pyrite Member appear to be products of local remobilization of sulphides under fracture-induced free energy gradients during regional metamorphism and tectonic deformation.The contrasting mineralogy of the two vein types may have arisen as a result of differences in the structural orientation of the veins and!or the relative ages of the veins.

Jan 1, 1969

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

By R Simcock

Why Rehabilitate? Legislative Requirement Land rehabilitation is a condition of resource consents for mining. Clause 17 (1) of the Resource Management Act 1991 (duty to avoid, remedy, or mitigate adverse effects) provides the legislative basis for local authorities to impose resource consent conditions requiring land to be rehabilitated to approved uses during and after mining.

Jan 1, 1997

By R Herbert, M E. Malmstr÷, S U. Salmon

The study focuses on sulfide oxidation processes in unweathered pyrite-rich mine tailings from a soil-covered impoundment in northern Sweden. To simulate the oxygen-limited conditions in water saturated tailings two long-term column experiments were performed. Results are presented for the first 11 months of the experiments at room temperature. The tailings used in the experiments were of two different grain sizes (one coarse grained, in the range 0.02 - 0.6 mm with a grain surface area of 1.86 m2 g-1, and one fine-grained, in the range 0.0015 - 0.06 mm with a grain surface area of 10.00 m2 g-1) and with slightly different mineralogical composition. The S:Fe molar ratio in the leachates (1.0 - 1.5) indicates either that pyrrhotite is the main iron sulfide undergoing oxidation in our experiments, or, alternatively that the S:Fe molar ratio in the leachate is determined by pyrite weathering in conjunction with other processes releasing iron or immobilising sulfate. However, speciation modelling of the leachates indicates that ferrihydrite was close to saturation, suggesting that a ferric oxyhydroxide may have dissolved/ precipitated during the experimental period, thereby affecting the S:Fe molar ratio. Pyrite oxidation rates obtained from the two column experiments during æsteady-stateÆ were 2.25 + 10-13 and 8.45 + 10-14 mol m-2 s-1 in the coarse and fine tailings, respectively. Pyrrhotite oxidation rates, as an alternative, were 2.31 + 10-12 and 1.24 + 10-11 mol m-2 s-1 in the coarse and fine tailings, respectively. Natural microbial activity was confirmed in both the tailings and the leachates; therefore, the obtained oxidation rates are not strictly abiotic. It is thus concluded, based on the experimental results, that tailing heterogeneity will result in zones with different oxidation rates, related to their physical and chemical properties.

Jan 1, 2003

Estimation of operating costs in the nickel production industry requires a detailed analysis of material flows from mine to smelter to refinery. Despite the small number of nickel producers compared to other base metals, the existence of two very different ore types (sulphide and laterite) and a wide variety of mining and processing technologies make the identification of these flows of critical importance if an accurate global picture is to be obtained. Smelting and refining processes in nickel metallurgy have evolved with a high degree of adaptation to specific operating conditions in different locations. Overall costs are calculated by combining individual cost elements for each unit in production chains from mine to saleable metal product. The average cost of western world primary nickel production in 1995 was US$2.07/lb ($4560/tonne). Average operating costs remained virtually unchanged in the three years to 1995 after an 8.5 per cent fall in 1993, but a 3.9 per cent increase to $2.15/lb is expected for 1996. A major factor in this rise results from the lower prices of copper and cobalt this year, reducing the by-product credits available to major producers.

Jan 1, 1996

A process was developed, on a laboratory scale, for the removal of iron oxides from Weipa pisolitic bauxite. The technique involves the chemical reduction ofthe iron oxides by carbon, followed by selective removal of the iron species by acid leaching or chlorination.To remove more than 90 per cent of the iron it is necessary to reduce the iron oxides substantially to iron metal by heating the bauxite, pre-calcined at 650-800°C, with reactive carbon at 1040-1100°C. Reduction proceeds via the intermediate formation of hercynite (FeO.Al2O3) and difficulties have been encountered in reducing hercynite formed under less favourable reduction conditions.Following reduction, efficient selective removal of iron species is readily effected by acid leaching using dilute hydrochloric acid at 100°C, or chlorination at 500-750°C using Cl2, Cl2/N2, or Cl2/N2/CO mixtures.After removal of unreacted carbon, the final products contain 0·5-1.0 per cent Fe203 and 87-92 per cent Al203.

Jan 1, 1971

During the last century Allis-Chalmers has supplied many screens of various types to industry, from revolving screens to the large capacity highly efficient screen available today. The features incorporated over these years in horizontal and inclined screens are varied and numerous and include many innovations such as tri-and bi-sloped screen decks. Today the emphasis is on wide vibrating screens with good "G" value, with large "throw", to achieve high capacity. Larger screens lead the way to treating a somewhat neglected area of mining operations - that of concentrator mine flotation tailings to allow effective transportation and stacking by conveyor belt. The benefits from a cost, water saving and environment view point are discussed in this paper.

Jan 1, 1984

Offshore petroleum development involves massive capital expenditure and financing demands, with the main participants being large international oil companies and State owned enterprises. Types of project oriented financing include take-or-pay contracts, throughput agreements, and production payment financing. The main project finance credit aspects are revenues, investment budgets and cost over- runs, reservoir, political and other risks and special problems such as weather and corrosion in the North Sea. A variety of documents is required and a mix of equity, export credit and Euro-market financing will typically be included in the financing.

Jan 1, 1983

If lead buttons are cupelled under closely controlled conditions in a suitable design of furnace, silver losses during cupellation are given by a simple equation. The effect of copper on these silver losses has been studied and a "copper limit" for cupellation has been determined. Scorification and crucible fusion procedures for copper-bearing materials have been designed so that the lead buttons produced will not contain amounts of copper greater than this determined copper limit. Silver losses during these crucible fusion and scorification procedures are given by the distribution law, and can be calculated. Thus, silver can be determined in copper-bearing materials with a satisfactory degree of accuracy provided that the appropriate corrections for losses are applied to the weight of the silver prill produced.

Jan 1, 1957

This paper reviews the manpower requirements of the Australian mining industry. It has been necessary to provide general background information in order to support the view that university education in mining and mineral process engineering should be strengthened rapidly in Australia to provide graduates for the industry.

Jan 1, 1969

By G R. Mould

The paper presents a general background to the subsidence research program being undertaken by the Department of Mineral Resources and Development in New South Wales. The results of the studies undertaken over the last ten years are summarised. The differences between these results and those obtained by the National Coal Board are discussed. The results of a study carried out on the effect of total extraction beneath a freeway in the southern coalfields are discussed in some detail. The procedures developed for the construction of a 500 mm diameter natural gas pipeline crossing a number of collieries in the northern coalfields are also outlined. The future direction of the Department's subsidence research program is discussed.

Jan 1, 1980

Market forces, particularly iron ore prices, demand that plant operators achieve higher throughput in the worldÆs iron ore beneficiation plants without compromising yields or efficiency. This means that production cost per ton is of paramount importance and that all major pieces of Processing Equipment have come under close scrutiny to improve throughput at their most efficient performance levels and for the longest possible continuous running time. Without doubt the use of modern engineering standards and materials of construction has contributed to matching these throughput, efficiency and availability demands. However, often not enough attention is paid to the so called æinsignificant elementsÆ connecting this metallurgical equipment, such as chutes, pipes or other conveying systems, and particularly to the sufficient protection of their wearing surfaces. The result can be an unplanned and expensive outage caused by the wear related failure of such components. This paper will discuss:the theory of wear and the multiple factors of material and design that contribute to a reduction in wear; and the combinations of modern wear resistant materials available to todayÆs engineer and how, by intelligent selection and correct application, plant availability can be optimised. Examples outlining how these principles have been applied in South Africa showing some improvements leading to increased plant availability.

Jan 1, 2002

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

Waitemata Tectonic Event(25 Ma ago) created a subduction system from the northeast of Northland, causing: (1) the emplacement of the Northland Allochthon (24-23 Ma) which provided argillaceous limestone and serpentine to Northland, and minor copper to both there and East Cape (located off Northland then); and (2) Northland volcanism (from 22 Ma), which lacked economic mineralisation. The Kiwitahi Tectonic Event (1714 Ma) caused: (1) a realignment of volcanism - from coastal western Northland, to west of the Hauraki Plains (Kiwitahi); (2) a start to the migration southwards from Northland of (a) the Alpine Fault System towards Marlborough today, (b) subduction towards Cook Strait, and (c) volcanism towards Taranaki-to-Bay of Plenty (initially through Coromandel, Kiwitahi, and offshore west coast); and (3) a start to rhyolitic volcanism & associated hydrothermal activity. The latter caused epithermal mineralisation, providing in Coromandel the best known North Island metalliferous deposits. Andesitic volcanism has been active in both of these two contrasting, subequal belts since 22 Ma. Rhyolitic volcanism and hydrothermal activity was wholly restricted to the eastern Marshall Belt, with an abrupt limit to economic mineralisation at the Volcanic Divide (within Hauraki Plains) and a major change there to basaltic volcanism of the western Searle Belt. The Kaimai Tectonic Event (5-1.5 Ma) caused: (1) a temporary reversal in volcanic migration in the Searle Belt, and a duplication of rhyolitic & hydrothermal activity at Waihi (Marshall Belt); (2) the rotational rifting of both the Central Volcanic Region (by 30¦) and the Hauraki Rift (10¦), causing major curvature of the North Island and New Zealand, and the transfer of the offshore subduction system from Coromandel to East Coast; and (3) an effective end to Coromandel mineralisation. Post-Kaimai Volcanism (1.5-0 Ma) included: (1) andesitic volcanism in the Searle Belt, yielding the western coastal titanomagnetite deposits; and (2) andesitic, and rhyolitic & hydrothermal activity in the Marshall Belt - the latter providing geothermal energy, sulphur, and pumice/perlite deposits. Post-Subduction (Intraplate) Volcanism (10-0 Ma) developed in a steadily expanding northwest region of relative tectonic quiescence, as subduction and its volcanism migrated southwards. Intraplate volcanism was predominantly basaltic, providing excellent aggregate; but less common rhyolitic & hydrothermal activity provided geothermal potential and mercury at Ngawha and at Puhipuhi, and halloysitic clays of extreme brightness elsewhere in Northland. This volcanism has reached as far SE as Mayor Island, providing an early New Zealand mineral resource - obsidian.

Jan 1, 1997

The Ross Goldfield is a unique gold resource. From its discovery in 1865 there was a growing understanding of the geology of the deposit as mining moved from the surface at Jones Flat in the south to underground extraction at Ross Flat further north. Multiple layers of gold-bearing gravels were penetrated in deep shafts and six rich gold-bearing bottoms were worked. The ultimate bottom on the Old Man Group gravel surface has never been reached either at Jones Flat or at Ross Flat. Mining at Ross Flat was ultimately halted by uncontrollable flooding, by escalating costs and by a shortage of labour during the First World War. Mining at Jones Flat recommenced in the late 1980s and attention has once again been drawn to the potential magnitude of the resource at Ross Flat. Research of historic literature shows that there is potential for a bulk gold grade of 400 mg/m3 in a volume of 82 million cubic metres of gravels which lie in a basin between Jones Flat and north Ross.

Jan 1, 1993

The Zeehan field has yielded over 190 000 tons of lead and 26,000,000 oz of silver. Moh of the production took place between the initial discovery of silver-lead ore in 1882 and 1920, and the greatest part was extracted from fissure lodes in the Proterozoic to (?) lower Cambrian rocks. It is demonstrated that the prosperity of the mines relied upon the silver content, which is apparently highest in these beds, particularly where spilitic rocks are associated with them. In contrast, galena occurring in orebodies emplaced in the Gordon Limestone is low in silver.Most of the workings are relatively shallow due in some cases to enrichment related to erosion surfaces.Fault zones within a complex anticlinal structure exposing the Proterozoic to (?) lower Cambrian formations appear to have been major factors in the control of mineralization.

Jan 1, 1968

The application of single liquid cement for fracture grouting in base rock may have history more than 120 years. The disadvantage of it is difficult to increase the grouting efficiency, because the jelling time of it is very long and hard to control. The double liquid grout, such as chemical grouts and cement water glass grout was developed at the end of 1960.'s Although the jelling time of this kind of grout can be controlled, it mast adopt double liquid grouting technology, use complicated equipment and is not easy to control component's ratio of the grout. Another disadvantage for chemical grout is high price, and have pollution to environment. OCE series single liquid grout is the effective grout material developed recently by making large efforts in Ohina. Main feature of it is that the jelling time is easy to control, materials from cement and clay are very cheap and without pollution to environment, and the grout can be injected by single liquid technology. The effect of QCE series grout has been proven by its application in China. It can be believed that QCE grout has great economic efficiency and will give a push to develop grout material.

Jan 1, 1988

By Hall J. S, Zuiderwyk M, Reid A. F

A prototype version of a computer controll- ed on-line scanning electron microscope image analyser, employing the real-time signals ob tamed by digital control of the electron beam has been used to obtain statistical quantificat lion of a wide range of mineral grain character istics, including composition, size distribut- ion, and degree of liberation. These propert lies have been determined for suites of whole particles of flotation concentrates, mounted without further preparation. The facility is also well adapted to the measurement of general Istereological parameters. The computer control software is based on an operating system which includes the device drivers and which is linked to FORTRAN programs [containing the procedural algorithms. The beam scanner provides a 4000 x 4000 point raster swept at a 10 Mhz rate in steps of 1 to 200 points and a set of up to 8 signal channels which respond to electron or energy dispersive X-ray signals to provide a digital attern.characterizing the sample composition. the beam is stepped at high speed until a part- 'cle or phase boundary is encountered; a longer well time is set if X-ray data is required. he digital scanner interrupts the computer

Jan 1, 1977

By M Maslowski, J B. Gemmell, D R. Cooke, C Zesati, J Castorena

The Palmarejo, Guadalupe and La Patria Silver-Gold epithermal vein deposits occur in south-westernChihuahua state, Mexico. The veins are hosted in a volcano-sedimentary sequence that comprises andesitic to basaltic resedimented volcaniclastic rocks, together with less abundant coherent and pyroclastic facies and minor red-beds. The host sequence is part of the Lower Volcanic Series, and formed in a magmatic arc environment during the Late Cretaceous to Early Tertiary Laramide Orogeny. The Lower Volcanic Series is overlain unconformably by an extensive sequence of Miocene rhyolitic ignimbrites, known as the Upper Volcanic Series. At this time, it is uncertain whether epithermal mineralisation was related to andesitic intrusions (85 Ma) and/or Oligocene rhyolitic dykes (25 Ma). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008