Search Documents

The major greenhouse gas emissions from coal combustion are leading certain people to argue for uranium mining and nuclear power to meet these challenges. Although there is considerable rhetoric around promoting nuclear power as 'green' due to its relatively lower greenhouse intensity, a careful study of the data is required to properly underst and the sustainability of uranium mining and nuclear power and whether it can or should have a role in future energy supply scenarios. This paper presents detailed research and analysis on uranium mining, focusing on known economic resources, production, solid waste and water management, pollution issues as well as energy and greenhouse aspects. A particular focus will be on Australia and its operating and prospective uranium mines. Overall, the paper raises fundamental issues concerning the long-term sustainability of uranium mining and nuclear power and documents the greenhouse intensity of uranium production and the nuclear fuel chain.

Jun 1, 2010

Dewatering tailing slurries by mechanical means is often not possible and gravity and solar driven processes must be used. It has been shown previously that better use of gravity is achieved when the tailing is drained as it settles. Not only are more compact sediments obtained but also the dewatering is faster. From the results of laboratory and field tests reported here, equations were established which describe the evaporation and drainage components of the dewatering. These equations were used to calculate the effects of ponding depth, solids content of the tailing and clim- atic conditions on the time required to dewater the tailing. Since the calculations can be made with and without the drainage component, the advantages to be gained with drainage can be determined. The tailing used in the work was a clay slime from a sand washing operation. However, it is anticipated that this approach will be applicable to other similar tailing.

Jan 1, 1978

By G K. Robinson

The existence of bias in samples taken by cross-stream sample cutters has been investigated using three-dimensional discrete element method (DEM) modelling. Detailed quantitative information on overall extraction ratios, size specific extraction ratios, missed and extra sample components can be made by comparing a reference sample to the actual sample. A key advantage of using this modelling approach over physical experimentation is that the reference sample can be measured on precisely the same portion of the stream of material as the actual sample, thereby allowing the elimination of a significant fraction of the variability and allowing statistically significant results to be obtained using many fewer replicates. Quantitative analysis of results broadly supports the commonly-used rule that the cutter aperture should be at least three times the nominal top-size of the material being sampled, but does not support the commonly-used rule requiring increase in cutter aperture if the cutter speed exceeds 0.6 m/s. Sampler performance can be understood in terms of the balance of forces in the congested region of material formed by the slowing of the particle stream due to collisional interactions around the mouth of the cutter.

Jan 1, 2008

By Ellson I. G

Advantage has been taken of the need to build the new mining town of Shay Gap to incorporate a new standard of living in an isolated area, which suffers from climatic extremes. The various problems associated with living in the Pilbara area of Western Australia are outlined, together with their effect on the design of Shay Gap.

Jan 1, 1973

By Struthers M. A

The basement contact zone, a major fault structure underlying the copper orebodies at Mount Isa, has a significant influence on orebody extraction. The zone is comprised of a variety of weak, barren lithologies which often create very difficult mining conditions, contribute to stope dilution, and have an adverse effect on concentrator recoveries.The geological characteristics of the contact zone are described, and the importance of timely, accurate geological information emphasized.A variety of mine design strategies have been employed to reduce the impact of the contact zone on orebody extraction. Some of these are discussed, together with current trends in the southern areas where orebody geometry and hence mining methods change markedly.Recent developments in ground support techniques, such as cable dowel reinforcement, have significantly improved ground conditions in the contact zone. An example of the methods employed to improve knowledge of ground behaviour is presented. The trend towards increasing automation and larger equipment requires larger excavations; consequently ground support practices and knowledge of ground behaviour must continue to advance. Rock mechanics investigations will remain an essential part of the mine design process.

Jan 1, 1990

By Watkins JR

The educational system is a dynamic; a flow resource that can be significantly shaped, changed and - refined by educationists. This paper analyses these various facets of geo- science education in Australia. The Australian educational philosophy is essentially a laissez- faire model, a free market approach without any real government or professional directive or stratagem. Students are therefore free to choose their own educational pathway dependent only upon their ability and the access to courses. Geological education at the tertiary level in Australia is described and critically analysed. There is a real need for a rationalisation of geological education in Australia, and this rationalisation should include not only the number of courses offered but should also aim to fully define both the philosophy and purpose of geological education and the accreditation procedures for the Students.

Jan 1, 1986

By R Engle, R P. McMahan, D A. Bowman, S Schafrik, W Thabet

Preventing injuries and fatalities related to conveyor system use in the mining industry is important and increases uptime while decreasing lost time. The research presented here is funded by the National Institute for Occupational Safety and Health (NIOSH), and intended to accomplish this prevention by the use virtual environments (VEs) to improve training and help miners better understand the hazards of working around conveyor systems. Two conveyor system VEs designed to teach miners about hazards and to safely complete tasks around conveyor systems were developed for this project. The first conveyor system VE, called the instructional tour, gives the miner a semi-automated tour of a conveyor system and teaches the miner about possible hazards (eg, missing guarding) and how to safely fix conveyor problems (eg, a stuck idler) using lock-out, tag-out procedures. The second, called the virtual shift, allows the miner to freely navigate around a conveyor system to detect and avoid hazards. The miner is presented with equipment failures that need to be safely repaired during the virtual shift. If the miner fails to identify and avoid a hazard or fix a failure in a safe manner, an animation of the consequences is shown to the miner, who must start the virtual shift over. The models for the conveyor system VEs were created using 3DS Max. Desktop versions of the VEs were then created using Deep CreatorÖ, an authoring application for creating interactive 3D environments. Later, more realistic versions of the VEs were created for CAVEÖ, a room-sized visualisation system, using DIVERSE, an application programming interface. In initial evaluations of the conveyor system VEs, mining colleagues have indicated great interest in such training tools. According to their feedback, these and similar VEs would provide excellent alternatives to normal classroom training and serve as positive precursors to hands-on experience. These VEs provide new miners a chance to experience hazards associated with working around conveyor systems without being in possible danger.

Jan 1, 2008

By Watson F. G

As an introductory paper of a series on the Melbourne (Australia) Underground Rail Loop extension to the extensive electrified suburban railway system the paper outlines the need for the Loop, legislative background, organizational establishment, engage- ment of consultants, design control, contracts, financial aspects, example of organizational flexibility and certification and transfer of the Loop to the Victorian Railways Board.

Jan 1, 1981

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008

By Bonsall EM, Schwabe MR, Hamlyn DA

Historically, most of the gold produced from Kalgoorlie has been derived from the gold and gold telluride Golden Mile lode systems dominantly hosted within the Golden Mile Doler-ite and to a lesser extent, Paringa Basalt. In more recent times the gold-quartz stockwork ore bodies within Unit 8 of the Golden Mile Dolerite at Mt Charlotte have become increasingly imp-ortant.Extensive low grade gold mineralisation has now been defined to the north and east of Kalgoorlie within rock units of the Golden Mile sequence not generally considered to be highly prospective.Two main types of mineralisation have been defined. The first comprises variably mineralised and altered quartz-albite porphyr-ies emplaced within talc-carbonated Hannans Lake Serpentinite (Mystery deposit). There is intense fuchsitic, pyritic and carbonate alter-ation of the serpentinite adjacent to the porphyry bodies. Gold mineralisation is assoc-iated with fine-grained disseminations and veinlets of pyrite and narrow quartz and quartz-tourmaline veining within the porphyry and adjacent fuchsite-carbonate rock. Several sets of vein directions are present, some of which typically exhibit sulphide alteration haloesnnA H] rhina_

Jan 1, 1984

Some fundamental aspects of recent single-particle fracture studies are reviewed. Findings from this research shed new light on the utilisation of energy during comminution operations and provide useful pointers to new research directions that could lead to significantly better comminution machines. Two methods for quantitatively predicting mineral liberation during comminution are reviewed. These methods have been developed into useful practical procedures, but they are almost unknown in the mineral processing community. Their use should promote the consideration of mineral liberation as an important variable to be considered during the design and operating control of comminution circuits.

Jan 1, 1993

By Reeves T. J, Hansen J. Y

Dense medium cyclone theory, supported by extensive experimental and plant-scale evidence, demonstrates that medium rheology (stability and viscosity) substantially affects cyclone performance in mineral applications.Two instruments have therefore been developed to allow medium stability and viscosity to be-monitored in the plant environment. The instruments are described, and examples are given of their application in full-scale plants.

Jan 1, 1989

By Arumba J

In the Mount Victor area of the Eastern Highlands Province, re- connaissance geological mapping and new micropalaeontological data have revealed the existence of at least three small thrust- bound windows exposing late Middle to Late Cretaceous (Late Aptian-Early Albian and Late Santonian-Maastrichtian) sedimen- tary rocks and pillow lavas, Latest Paleocene- Earliest Eocene pillow lavas, and Latest Paleocene-Earliest Eocene bathyal micrites. Late Middle Eocene to Late Eocene inner neritic bioclastic micrite units also occurs in thrust contact with Middle Miocene Yaveufa Formation volcanolithic conglomerates. The Cretaceous and Early Tertiary units appear to be thrust-bound and are best exposed in a window just south of Mount Victor, and in two smaller windows to the east. The inner neritic Eocene limestone occurs in a thrust-bound sliver within the Yaveufa For- mation near Obura. The windows occur within extensive out- crop of Early Miocene Omaura Formation and the Yaveufa For- mation. Thin-bedded grey mudstone, siltstone and sandstone, typical of much of the Chim Formation form only a small part of the exposure of Cretaceous rocks. Thick-bedded volcanolithic conglomerate, spilitic pillow basalts, and welded basic tuffs domi- nate the Cretaceous section. The stratigraphy and structure of the Mount Victor area is similar to the Menyamya area, the Aure Scarp, and perhaps the Tapini area. This study has raised the possibility of widespread thrust- ing in the Kainantu area, and suggests that the boundary between the Omaura and Yaveufa Formations is thrusted, at least locally.

Jan 1, 1997

By Burks WG, Hughes FE, Muceniekas E, Whitcher IG

The area containing the iron field, recognised by the writers, is part of an uplifted, portion of the 'Western Australian Plateau,' ranging in elevation from about 1,000 feet to about 3000 feet above sea level. The local rock succession is flat-lying or moderately-folded and belongs to the Nullagine Series of Upper (2). Precambrian age. This series forms the Hamersley Rangeland vast portions of the...

Jan 1, 1964

By Orid A

A fast, non-contact technique for measuring sizes of rock fragments on a conveyor belt is presented. An image processing technique called active stereopsis is used which makes use of a light stripe projected on to the surface of the fragments on the conveyor belt. A CCD TV camera is used to capture the shape of the distorted light stripe. the video image of this shape is then processed by a computer program so that the 3D profile of the surface can be obtained by triangulation. The sizes of the rock fragments are then calculated from this profile. The speed of the technique is improved by calibrating the light stripe system before measurement begins so that the profile of the fragment surface can then be measured using simple geometry. The technique is fast and highly parallel so that it is able to operate in real time.

Jan 1, 1990

By Bowden MW

Sintering of lead-zinc concentrates is practised by Sulphide Corporation to provide both desulfurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulfur dioxide gas for sulfuric acid manufacture.Moisture control of feed mixes is of paramount importance in the sintering operation and improvements in this area have realised increases in overall plant performance.

Jan 1, 1985

By Yao S, Wang P, Zhang C

The Zhilingtou Au-Ag deposit is situated in the eastern part of the complexly deformed and metamorphosed South China Caledonian Fold Belt. It consists of seven orebodies that are almost exclusively hosted by biotite plagioclase gneiss of the Precambrian Chencai Group. They form an apparent en echelon pattern in both cross-section and level plan. Three different ore types, based on mineralization textures, have been recognized within the Zhilingtou lode. These are Au-Ag-rich quartz veins, Au and Ag-bearing silicified rocks and Au-Ag-containing altered rocks with quartz stockworks. The mineralization is principally composed of electrum, argentite, pyrite and minor sphalerite, galena as well as traces of hessite and chalcopyrite plus a gangue assemblage of quartz, rhodonite, sericite and chlorite. Fluid inclusions related to Au-Ag mineralization yield a wide range of homogenization temperatures from 110 to 447¦C, with two distinctive peak values at 250-300¦C and 350-400¦C respectively. S30Si values of quartz veins and silicification from the three stages of mineralization range from -0.1 to -0.4%o. The mineralization at Zhilingtou is interpreted as forming by recirculated meteoric water extracting ore-forming elements from metamorphic rocks due to Mesozoic volcano-magmatic activity.

Jan 1, 1995

By Segnit R. E

Two suites of dusts (waste-heat boiler and electrostatic precipitator) collected in 1976 and 1980 from the Kalgoorlie nickel smelter were subjected to chemical and XRD analysis and were examined by SEM and optical microscopy. The spherical to sub-spherical particles contained oxide and glassy phases with small amounts of sulfide. XRD showed that the major phase was a mixed Ni-Fe oxide spinel with some hematite. These phases compared well with those predicted by thermodynamics. The particle size distributions showed that in the 1976 and 1980 suites 20 per cent by weight was respectively coarser than 60 and 115/lm (boiler dusts) and 40 and 30/lm (precipitator dusts). Maximum particle sizes estimated from sedimentation chamber theory were found to be in reasonable agreement with the maximum sizes found in the dusts.

Jan 1, 1984

Five Hypotheses are given for factors influencing long-run metals price forecasts. 1 . Geologists succeed when given the money. 2. Better understanding of a metals market depresses its price. 3 . Statistical techniques get forecasts wrong. 4. Long-run metals prices are related to crustal abundance. 5 . Economic cycles affect metals prices more than is realised. These are then framed within the transition between eras as influenced by apparent long waves in economic activity. Innovation surges during the transition between eras. The transition to the 5th Wave since the Indus- trial Revolution 200 years ago is now underway. Finally, price projec- tions are given both for the 5th Wave and 200 years from now on the assumption that a similar monetary measure to today will be then extant.

Jan 1, 1988

By Smallnone P, Walker B

Mining of the AKI lamproite pipe at the Argyle Diamond Mine (ADM) commenced in 1985. Originally designed to mine ore at a rate of 3.6 Mt per annum, the project has gone through two major plant expansions to a designed production rate of 8.7 Mt

Jan 1, 1998