Search Documents

The total cost of horizontal development can be minimised by optimising the cost of each of the component operations (eg drilling, blasting, etc). Component costs should not be minimised. To optimise blasting results (ie the mean advance per round, muckpile characteristics and overbreak), operators need to optimise the blast design and drilling and blasting procedures. The costs of pulling extremely long (say >6 m) rounds, producing unnecessarily fine fragmentation, and minimising overbreak are excessively high. Operators should continually consider how they can shorten the cycle period by saving time at the face. To enable it to be matched to the pertinent rock properties, the blast design needs to be based on as much relevant experience as possible. To develop the most valid correlation between blasting results and blast design, the latter must be implemented carefully and accurately, but without sacrificing speed excessively. The total cost can often be reduced by using: 1. computer-controlled jumbos (to reduce the period and cost of drilling and to increase drilling accuracy); 2. larger diameter (51 mm to 64 mm) and longer (4.5 m to 6 m) blastholes; 3. at least three large diameter ( ¦89 mm) relief holes that are 0.2 m to 0.3 m longer than the blastholes; 4. explosive products that are selected on the basis of proven reliability and overall cost efficiency rather than price; and5. stemming (to increase the amount of effective work done by each kilogram of explosive and, hence, to reduce the powder factor and possibly the number of blastholes and the costs of drilling and initiation). Non-perimeter blastholes should be charged with ANFO or a bulk emulsion of established performance. Upper perimeter blastholes should be charged with a bulk explosive with a much lower effective density. But where geology varies considerably, greatest control over overbreak could possibly be achieved with the versatile pre-assembled charge shown in Figure 1. This paper presents numerous potential ways in which the total cost of development can be minimised. It concentrates on recommending blast design features and the safe, rapid, cost-effective implementation of designs.

Jan 1, 1998

By A Kobzev, C Robben

Sensor-based particle sorting of gold ores is the masterclass of preconcentration. The technical challenges of a grade in ppm scale makes a direct detection with currently available technology in milliseconds impossible. Consequently, the detection and classification of particles into ore and waste classes relies on detectable proxies which are the foundation for the classification. These must be reliable and repeatable across the ore bodies processed in future. A sensor-based particle ore sorting equipment must therefore be calibrated systematically by understanding the gold deportation in different lithological groups. Also, it must be in best operational state to minimise possible misplacement. The technical challenges are met by a stringent financial regime governing the business case. Many gold ore sorting projects require a stable grade of gold in the rejected waste significantly below 1gr/t. Two examples are introduced in this paper:  The pilot results and operational experience of X-ray transmission (XRT)-based particle ore sorting for pebble sorting of sulphide associated ore;  Laser-based particle ore sorting for pebble circuit of an orogenic, quartz associated gold ore. Usually, sensor-based particle sorters are installed in the crushing section of a plant. However, for large capacity plants, the number of equipment required, and the associated material handling costs result in significant capital and operating expenses for plants with 1200tph run-of-mine capacity. As a conclusion, it was decided to investigate sensor-based particle ore sorting applied to the pebble stream of two existing semi autogenous mills.

Nov 10, 2020

By T Tan, C P. Holmes, C E. Hartford

Transportation of iron ore from the mine to the plant is critical to business success. Ore from the mine may have to be transported across states, countries and even continents to get to the processing plant or export facilities, and ultimately to the client. Numerous transportation steps may result in potential logistical difficulties. Companies are continually seeking ways to increase production rates, decrease delivery times and reduce operating costs. Transportation cost is a major component of the total cost of mining iron ore and therefore requires effective use of transport systems.Bottlenecks in iron ore transport systems, due to material handling issues, can result in loss in profit in the order of millions of dollars per hour. Bottlenecks can be seen anywhere in the transport system where the desired flow rate cannot be achieved. These bottlenecks occur for various reasons such as increasing throughput in a transport system originally designed for a lower throughput resulting in plugged transfer chutes, changing material characteristics (eg finer material, increased moisture content), changing to a new type of material or blend that again alters handleability, or changes in operational philosophy due to equipment availability or process utilisation.Stockpiles may have limited live capacity such that an adequate amount of ore may not be readily reclaimed when required (eg to fill a complete train’s railcars). In bins and hoppers, material may discharge through a central flow channel resulting in the formation of a stable rathole, which can then collapse causing material to flood the downstream system and cause significant downtime for clean-up (eg railcars beneath train load outs). In transfer chutes, bottlenecks can be caused by pluggages or downtime required for the change-out of liners due to excessive wear. In ship loading, long settling or de-aeration time, or material exceeding its transportable moisture limit (TML) may result in further bottlenecks. These bottlenecks all have associated costs because of the need to address their causes and because of the lost opportunities for throughput.This paper will discuss how bulk material technology and proper understanding of material flow characteristics can be applied to mitigate bottlenecks. It will discuss how to predict potential bottleneck locations through a scientific method of analysis and evaluation to determine if an increase in throughput of an existing transport system is possible, as well as whether or not a new material will flow reliably through an existing system.CITATION:Hartford, C E, Holmes, C P and Tan, T, 2015. De-bottlenecking iron ore transportation from mine to plant, in Proceedings Iron Ore 2015, pp 393–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The creation of an accurate and precise enough database requires the collection of many representative samples, subsampling and assaying them without destroying their integrity. The selection and implementation of sampling protocols often lead to severe difficulties, making the unaware practitioner vulnerable to massive exploration, feasibility and operating failures. Therefore, there is no substitute for a good understanding of the Theory of Sampling (TOS). Either because of ignorance, or because of short-term economic reasons, failure to comply with many stringent conditions can be devastating for the validity of a feasibility study, leading to false evaluations, to the abandonment of a viable property, or to the exploitation of one that is not profitable. All these failures have something in common: insufficient duplicate sampling, subsampling and assaying were performed; very important, preliminary heterogeneity tests were never performed; for short-term economic reasons, poor sampling and subsampling protocols were selected, second-class sampling systems and weightometers were installed and poor preventive maintenance and cleaning were implemented;and sampling experts were called only when the project was obviously in trouble. The conclusion is clear: in due time, iterative auditing of sampling practices is an insurance policy against massive financial losses for the company involved. A complete, comprehensive 100 point checklist of sampling Quality Assurance and Quality Control is provided, so critically important details to ensure success are not forgotten.

Mar 1, 2010

By P Minkkinen

"Pierre Gy showed in his early works that the results in estimating the variance of the mean value of continuous lots depends on sampling mode (random, stratified or systematic), except in the theoretical case that the measurand is randomly distributed in the lot. The experimental variance estimate calculated from samples taken from the lot is independent of sampling mode but depends on sample size and the type of the lot heterogeneity. Variography can be used to estimate the variance of the lot mean for different sampling modes.Gy also defined weighting error, which is made if a simple average is calculated from the assays of samples taken from a continuous object (eg from a process stream) where the flow rate varies with time and is correlated with the concentration of the analyte in the stream.The effect on sampling uncertainty of the three sampling modes and their interaction with the following factors in estimating the uncertainty of the mean concentration is studied using simulated lots, and lots having heterogeneity patterns similar to those of real data sets, including the effect of: the type of heterogeneity (random, grading and clustered heterogeneity patterns) increment size and number employing composite sampling weighting error. CITATION:Minkkinen, P, 2017. Dependence of the variance of lot average on the sampling mode and heterogeneity type of the lot, in Proceedings Eighth World Conference on Sampling and Blending, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By C Jacobsen, N Harries

Assessing and managing instability hazards is an essential activity when working with unstable natural slopes and excavated open pit mining slopes. Slope monitoring has become the standard technique for the management of geotechnical risks associated with mine slope instability hazards. In recent decades, a proliferation of new monitoring techniques such as terrestrial radar, satellite InSAR and LIDAR have become standard operational tools, complementing conventional survey-based monitoring solutions. A reliable monitoring system should identify and record incipient anomalous slope movement. Although the most obvious purpose of a monitoring system is safety related, slope deformation and performance monitoring also enhance the understanding of slope behaviour and assists in improving system design and implementation. For a monitoring system to be considered an effective early warning tool, it needs to operate in real-time and should be linked to the mine’s emergency communication systems. Terrestrial radar systems have been developed that can provide near real-time measurements, at a high level of precision and covering broad areas in all weather conditions. This has had a positive impact on the management of geotechnical risks in operational conditions. The technology adoption of RADAR in mine monitoring has significantly progressed in the last 20 years from technology enthusiasts, to visionaries, to pragmatists to conservative users. However, the increasing adoption of RADAR cannot reduce or remove other monitoring techniques that often have important benefits; even if these technologies cannot be used as a real-time operational tool. An increasing awareness on the importance of combining data from different monitoring techniques to develop a holistic picture of all possible geotechnical hazards is a current industry trend. This is proving to be an excellent foundation for managing hazards associated with slope instability in open pit mines, and is only expected to improve with time with the adoption of new technologies based on big data and Artificial Intelligence (AI).

Nov 29, 2022

By J Heyes, G A. Maddocks, R J. Stewart, G D. Corder

Mining is an international business and vital contributor to national and global economies. It depends on the trust and confidence of investors and stakeholders for its financial and operational well-being (Committee for Mineral Reserves International Reporting Standards (CRIRSCO), 2016). The Social Licence to Operate (SLTO) is an increasingly multifaceted and multistakeholder risk that can impact investment decisions. Community challenges to broader political and economic decisions have given rise to protest delaying or stopping projects or closing mines and has led to loss of life (Ernst and Young, 2016). Some governments are now giving greater powers to stakeholders to make the final decision on approving mining and metals activities (EY, 2016). With billions of dollars in project investment at stake, ongoing engagement, collaboration and effective communication with stakeholders is crucial and mutually beneficial solutions are increasingly expected (EY, 2016). It is therefore essential that the industry communicates the risks (and opportunities) associated with investment effectively and transparently in order to earn the necessary level of trust with investors and stakeholders to underpin its activities (CRIRSCO, 2016). Despite this need, investor and stakeholder trust in the sector has eroded in recent years.CITATION:Maddocks, G A, Corder, G D, Heyes, J and Stewart, R J, 2016. The social licence to operate and drivers for change – resource reporting and mine material characterisation, in Proceedings Life-of-Mine 2016 Conference, pp 183–187 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Interaction between rock and fluid plays a critical role in rock engineering ventures such as stimulation of oil and gas wells, geothermal energy recovery and nuclear waste isolation. Robust and reliable design of the related services and underground facilities is based on understanding of the mechanics and chemistry of the coupled hydromechanical- thermochemical processes. This paper explores the application of the theory of such processes in minerals engineering, with particular reference to rockburst mitigation, in situ solution mining and cavity completion of coal-bed methane production wells.

Jan 1, 1995

The Mobile Miner MM130 was delivered to Broken Hill in February 1992. During March the machine was extensively trialled on the surface to test manoeuvrability, climbing ability and muck handling prior to being trammed underground in April. The first cutting test on 30 April 1992 provided promising results. The machine has undergone continual development since it arrived in Broken Hill with aims of ensuring reliability and achieving performance goals. The paper gives a detailed account of recent performance comparing this with the predicted Performance.

Jan 1, 1993

By E Williams

The role and importance of a well designed test work program during the development of an orebody is often underestimated. A test work program should be tailored to deliver very specific answers to relevant questions. With a clear purpose, the results from the test work program will enhance the outcome of the feasibility study and provide the information required to meet the requirements of all stakeholders. With regard to test work programs there are three main areas that should be considered: orebody characterisation and definition, process flow sheet development and engineering design information.Orebody definition relies on reliable analytical methods to characterise and assess the economic minerals present in the ground. In mineral sands, the physical processing characteristics of the minerals play a significant role in the definition of an orebody. The analytical method therefore has to be customised using a combination of laboratory techniques. These techniques can include heavy liquid separation, gravity separation and magnetic separation and are usually combined with chemical and mineralogical analyses to create a picture of the orebody. During the definition phase of test work programs, an appropriate analytical technique has to be developed to evaluate drilling samples, but also to support the information collected during flow sheet development.Process flow sheet development is usually done once there is a reasonable understanding of the size and variability of the orebody. Selecting the best sample for test work is critical, as any flow sheet design is tied to the specific characteristics of the sample used for development. There are other factors that can improve the outcomes of flow sheet development test work, including the skills and knowledge of the operator and allowing sufficient time to process and analyse the results. Very often this work is conducted under pressure with limited time and resources, only to result in a suboptimal flow sheet. During this phase of flow sheet test work, iterative testing will provide the information required to develop an optimal metallurgical flow sheet. The data collected will provide indicative recoveries and yields that are required for feasibility studies.Equipment specification is often included as part of process flow sheet development. This includes comparative test work between different equipment suppliers, assessment of operating conditions such as the loading to determine the number of processing units required, as well as other design information required such as particle size distributions, density and operating temperatures.While restricting the time and costs expended on test work programs may seem to meet a short term need to meet investor requirements, neglecting to develop a proper framework of the requirements that has to be met in the long-term can lead to significant long-term cost overruns. This is mainly due to a need to repeat test work, or do confirmation test work, as insufficient information was collected during the initial program.

Oct 5, 2011

By P Bartsch

Uranium solvent extraction, USX has been applied commercially for recovery and concentration for over 50 years. Uranium in acidic liquor, which is prepared following ore leaching, solid/liquid separation and clarification, can be treated through a sequence of operations; extraction-scrubbing-stripping, to obtain purified liquor. USX has dominated the primary uranium industry as the preferred technological route to converter grade yellowcake. The practices of design and operation of USX facilities has found renewed interest as new mines are developed following decades of industry dormancy. This article seeks to outline principles of design and operation from the practitioner’s perspective. The discussion also reviews historical developments of USX applications and highlights recent innovations. This review is hoped to provide guidance for technical personnel who wish to learn more about good practices that leads to reliable USX performance.

Aug 8, 2011

By M A. Noppé

Mining is inherently a risk-based business and risk governance is an integral part of corporate assurance and business decision-making. Mineral Resources and Ore Reserves are the key assets for a minerals company and senior management/company boards require assurance regarding the likely accuracy of estimated and reported technical information. Reviews and audits improve the level of assurance in the reliability of estimated short-term (grade control) estimates, reconciliation, Mineral Resources and Ore Reserves.Peer reviews and audits contribute not only to governance processes, but also provide valuable technical improvement opportunities, as well as mentoring and professional development guidance to those whose work is being reviewed. Technical review is particularly crucial at a time in the industry when companies are running lean or perhaps inexperienced teams, with limited technical or management oversight.Despite both industry guidance and some companies’ standards expecting or requiring reviews and/or audits of Mineral Resource and Ore Reserve generation and reporting processes, it is surprising how infrequently or ineffectively these are actually carried out. Examples of governance systems are presented, which include appropriate peer review processes that if effectively applied, can identify shortcomings in technical processes and provide timely correction to prevent, or mitigate against, erroneous outcomes.Peer reviews are ideally carried out concurrently with the preparation of data, selection of estimation procedures and validation of outputs from Mineral Resource and Ore Reserve estimation prior to the handover of results between disciplines, or the final reporting of results. Audits, on the other hand, are generally retrospective reviews by independent and/or external reviewers who rate the risks inherent with an already completed process, identifying opportunities for improvements in the future.This paper outlines the main components of peer reviews and audits, discussing how a combination of these can provide a structured and objective assurance system leading to systematic and disciplined processes to improve the effectiveness of, and confidence in, grade control, reconciliation, Mineral Resource and Ore Reserve risk management, and support good governance.CITATION:Noppé, M A, 2017. Improved assurance for Mineral Resource and Ore Reserve estimates and reporting through peer review and auditing, in Proceedings Tenth International Mining Geology Conference 2017, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Classification within the Inferred Resource category is based on geological judgement and the balance of extrapolation versus interpolation that the Competent Person is prepared to accept. These resources are typically drilled at spacings well in excess of the geostatistical range and at a density that is non-uniform. In many cases, a substantial proportion of the available data will be historical, and should be considered with more recent data sources. The provision of a robust geological model will increase the confidence in any resource estimate, and should be viewed as a critical component. The definition of Inferred Resources is of great importance to vein gold projects, since Indicated and Measured Resources generally require costly underground development for delineation. Indeed, many gold vein operations possess substantial quantities of Inferred Resources (>75 per cent) in their resource inventory both at project start-up and during production. This contribution explores a number of the key issues when using the Inferred Resource category and presents four recent case studies.

Jan 1, 2006

By D Johansson, A Nordqvist, D Mihaylov, N Petropoulos, M Wimmer

The flowability of the caved rock masses in the sublevel caving (SLC) mining method is of great importance. During the blasting process of a SLC-ring, the caved rock mass in front of the ring is compacted. As a result of this compaction, the mechanical properties of the fractured rock masses change, for example void ratio, angle of internal friction and structure of the compacted material. The changed mechanical properties of caved rock mass and recent blasted material can influence the mobility of the material, which could result in blockage of the flow path of the material. The identification of the involved mechanisms in this process can be done after a series of tests in different scales. However, there is no available equipment for dynamic measurements during blasting, ie velocity and displacement of the burden and in the caved masses. This study focuses on the development and laboratory evaluation of a measuring system that can be installed in a borehole. The first trial was carried out in a pillar, where two blastholes had been drilled (9.5 m) parallel with the drift and two measuring holes (16.5 m) were perpendicular to the drift. Two measuring systems were installed in the measuring holes. Some preliminary tests were carried out to find suitable initiation procedures for the emulsion explosive. Applicability and robustness of the developed measuring system were also evaluated. In addition to these tests, an expandable cement mixture was developed to firmly anchor the measuring systems in the boreholes. The measuring system consists of an anchor, armoured cable in a pulling tube and a protective case. The anchor is equipped with uniaxial and triaxial accelerometers. A potentiometric measuring system for displacement up to 2 m is installed at the end of the pulling tube and connected to an extendable spiral cable. All sensors are connected to a data acquisition system (DAS). Both measuring systems have their own DAS to acquire data in case of failure of one of the systems. The measuring system was tested in laboratory conditions with impact velocity up to 10 m/s. It was proven to be functional and gave reliable results.CITATION:Petropoulos, N, Mihaylov, D, Johansson, D, Wimmer, M and Nordqvist, A, 2015. Design of equipment for dynamic burden measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 493–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Trout, B Macaulay

Ridgeway Gold Mine (RGM) is an underground sublevel caving (SLC) operation that is owned and managed by Newcrest Mining Limited (NML). Production drill and blast practices are critical to the success of the SLC method at RGM. SLC production ring precharging was introduced in November 2001 to enhance these practices and deliver safety, productivity and cost improvements. Current precharging practices require up to two rings to be loaded ahead of the ring to be blasted in each drawpoint. The explosive may be required to remain in the up-holes for periods of four weeks or more prior to blasting. During this æsleepÆ time it is subjected to repeated shock from the blasting ofadjacent rings and from rings in adjacent drawpoints. The project described in this paper was designed to gain an understanding of the factors affecting explosive performance in the precharging environment and to develop explosive products and operating practices that would meet RGMÆs requirements in terms ofsaf ety, reliability and blast outcomes. Several months oflaboratory and field testing were required to characterise the explosive and quantify the effect of post-loading blasting shock. These results were used to determine the most appropriate loading and sleep time criteria for RGMÆs precharging practices. In addition, the information is being used to guide the development of the next generation of emulsion explosives for use in underground precharging operations.

Jan 1, 2005

By M Araos, I Onederra

A novel explosive formulation that substitutes the use of ammonium nitrate (AN) with hydrogen peroxide (HP) as the main oxidising agent has been developed and tested as part of an Australian Coal Industry Research Program (ACARP) project. The main objective was to provide a step-change solution that has the potential to completely eliminate NOx fumes in blasting. The development of this HP/fuel-based explosive started with a comprehensive detonation characterisation program, consisting of unconfined velocity of detonation (VOD) measurements of samples at different diameters, densities and void sensitisation techniques. VOD results showed that the HP/fuel-based explosive mixtures behaved similarly to non-ideal commercial explosives; in that way mixtures could be tailored to achieve specific detonation performance targets. The next stage of testing in this development involved preliminary confined tests to evaluate the rock breakage potential of the HP/fuel-based explosive mixtures. Fully instrumented single-hole tests were conducted in a limestone quarry. Results from these preliminary trials confirmed the rock breakage performance of HP/fuel-based explosive mixtures. The confined VOD measured in one of the tests was 5100 m/s in a 102 mm diameter blasthole at a density of 0.96 g/ml. The corresponding borehole pressure measurement of this HP charge was 2.61 GPa with a detonation temperature of 2921°C. Based on near-field accelerations, both HP and ANFO charges displayed similar attenuation characteristics in the test conditions. Post-blast observations indicated that the breakage performance of the HP mixtures clearly reflected the in-hole detonation performance measurements obtained, confirming the ability of these explosive mixtures to both fragment and effectively displace the rock mass under evaluation. Further research work continues with the future commissioning of a prototype mixing and delivery unit, the successful completion and analysis of data from multiple-hole trials, and further characterisation work associated with product stability, reliability and performance under different geotechnical conditions.CITATION:Onederra, I and Araos, M, 2015. Detonation and breakage performance of a hydrogen peroxide-based explosive formulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 565–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Mitchell, S Pushpan, G Ferres, K Bobbermien, L Hudson

"Falling commodity prices and a rising supply surplus have ushered in a period of restraint in capital project investment across the global mining and metals sector. Competition for capital project funding has seen fewer projects progress through investment gates and a stronger focus on projects that deliver gains in capital productivity and strategic outcomes.Over the course of the 2015 financial year, EY conducted a study of 108 projects in the global mining and metals sector (EY analysis; Larsson and Ericsson, 2014; SNL Financial, 2015). The projects studied were at various life cycle stages and related to the development of copper, iron ore, gold, coal, nickel and other commodities. Each individual project investment exceeded US$1 B, and the studied group represented a cumulative investment value of US$367 B.The research found that the majority of projects were delayed and/or over budget when measured against the initial estimates made during the early stages of the project life cycle. Of the surveyed projects, 69 per cent were identified as facing cost overruns with an average overrun of 62 per cent above the initial estimate and 50 per cent reported schedule delays, even after remedial acceleration initiatives.The analysis found that budget and schedule overruns could be attributed to five key causes:project management factorsstakeholder conflictsresource constraintsregulatory, and policy-related challengesunfavourable external environment.Improving project delivery performance starts with successful planning, followed by rigorous management during delivery. From global experience on large and complex capital programs, EY has observed a consistent theme of underinvestment and a lack of focus in three often-overlooked but critical areas:implementing effective governance and reporting frameworks with lead indicators that reliably flag emerging risks while they can still be mitigatedallocating adequate cost and time contingency to account for risks across the life cycleenhancing the value of contingency by aligning contingency plans with scenario plans.This paper explores the surprising findings of the study, proposes a root cause model and examines key considerations in applying these critical enabling techniques.CITATION:Hudson, L, Mitchell, P, Ferres, G, Bobbermien, K and Pushpan, S, 2016. Are your megaproject schedules and costs under – or out of – control?, in Proceedings Project Evaluation 2016, pp 75–85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By S T. L Harrison, J-P Franzidis, M Becker, N Dyantyi, J L. Broadhurst

Gold mining is a major contributor to the South African economy, but is associated with several environmental issues such as acid rock drainage (ARD). ARD is due to the oxidation of sulfides in gold tailings and is characterised by low pH, high sulfate content and elevated concentrations of heavy metals that contaminates scarce water resources and subsequently limits the use of such waters without treatment. Treatment strategies can only be implemented if the acid-generating potential of mine wastes is effectively predicted using common static and kinetic acid prediction tests. The choice of test performed is usually a trade-off between the number of samples, speed of the test, cost of the analysis and level of information obtained. Often the results of these various tests are not consistent with one another. This study uses mineralogy to analyse biokinetic test results of a Witwatersrand gold sample in order to improve the understanding of behaviour of mine wastes under different ARD prediction test conditions.All ARD prediction testing methods investigated in this study showed that the gold sample is considered to be potentially acid forming with net acid generation (NAG) pH of 2.5 and net acid producing potential (NAPP) of 36 kg H2SO4/t. Results of biokinetic test showed that ANC was consumed within four days confirming acid producing potential of the sample with low neutralising potential as observed from acid base accounting (ABA) (4.7 kg H2SO4/t) and mineralogy (4.9 kg H2SO4/t). Results generated in this study demonstrated importance of mineralogy in both understanding the controlling reaction mechanisms playing key role in ARD formation and its capability as a prediction technique. Future work will focus on the application of mineralogy in interpreting the behaviour of mine waste under different static test conditions with a view to assessing their applicability and reliability in estimating potential acid generating characteristics of gold tailings.CITATION:Dyantyi, N, Becker, M, Broadhurst, J L, Harrison, S T L and Franzidis, J-P, 2013. Use of mineralogy to interpret laboratory-scale acid rock drainage prediction tests - a gold case study, in Proceedings World Gold 2013, pp 519-526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A C. Chieregati, A Heberle, F L. S P Villanova

Since the publications of Gy’s initial work, many authors have discussed the approaches to estimate the variance of the fundamental sampling error (FSE). Experimental tests suggested by Pitard and François-Bongarçon determine the sampling parameters K and a to calibrate Gy’s formula. The heterogeneity test and the sample tree method are well known and broadly used for many commodities. However, prior to the analysis, the collection of a representative sample is an intriguingly difficult task. The composite for the heterogeneity tests often consists of run-?of-?mine material or processed ore on a conveyor belt. In most cases the final sample does not have enough mass, mixes different geological units, represents a rare blend and does not characterise the deposit. In order to obtain a reliable composite for trace elements and low-grade ores, sampling practitioners suggest at least half a ton of material.To prevent the common representative pitfalls in the FSE, this case study focuses on a single gold-?bearing geological unit collected in situ. With this unit being structured by the mine geologists, but with the interaction between engineers and chemists, it was possible to validate the reconciliation suggested by Pitard (2015). The heterogeneity test and the sample tree method were performed using 500 kg of a smoky quartz from a single geological domain and the results were compared to Gy’s formula. The logging practice by the geologists was modified, emphasising the definition of the size of the gold nugget or its cluster, number of grains and association. Finally, a mineralogical study was conducted on the geological unit to define the liberation factor. All the information is compiled in this paper, showing the need to fully understand the mineralisation to correctly define representative samples and proper analytical techniques.CITATION:Villanova, F L S P, Heberle, A and Chieregati, A C, 2017. Heterogeneity tests and core logging – a final reconciliation, in Proceedings Eighth World Conference on Sampling and Blending , pp 107–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By F Kock, Y Sulianto, T Trott, B G. Putland, D Morgan

"Northparkes installed and commissioned a secondary crushing circuit in 2010 to debottleneck the semi-autogenous grinding (SAG) mill constrained grinding circuits. Following further improvements to the circuit (inclusion of a double deck vibrating screen), the project successfully delivered finer feed to the SAG mill. The result of this project was an increase in the milled tonnes from 5.6 Mt/a in 2012 to 6.0 Mt/a in 2013.The increased throughput rates introduced new challenges with the circuit becoming power limited. How to best optimise the available comminution power, while delivering the optimal particle size to the flotation circuit was made the key optimisation objective. To achieve this objective, Northparkes initiated a project that included engaging comminution experts. Recommendations included changes to the SAG mill including mill lifter design, increased grinding media charge levels and reduced grinding media size with aim of producing a finer grind size.Northparkes implemented these recommendations along with some other changes to SAG discharge grates and the mill discharge vibrating screen. This achieved a substantial reduction in the flotation feed particle size distribution (approximately 20 microns) by utilising increased average SAG power utilisation, in turn resulting in a two per cent increase in copper recovery.With power utilisation now maximised, the next phase of optimisation has moved to the throughput-grind-recovery relationship and the cost benefit analysis of installing additional grinding power.Citation:Sulianto, Y, Trott, T, Morgan, D, Bell, T, Kock, F and Putland, B, 2016. Optimisation of Installed Mill Power Post-installation of Secondary Crushing Circuit at Northparkes Mines, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 331–338 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016