Search Documents

In the course of work being carried out in the Lubricants and Bearings Section of the Council lor Scientific and Industrial Research on the production of copper4ead 'bearings for 'use in aircraft, it has been found necessary to develop special metallographic methods. For proper control of the production of steel-backed copper-lead bearings it is necessary to adhere to rigidly controlled conditions, and it is essential that a method of examination be adopted which will readily detect actual defects or any variations in quality. Some defects can be observed with the naked eye, whilst others are detected by radiographic examination. This latter method is invaluable as a rapid, reliable test in the production of aircraft bearings, but it is necessary to observe the structure of the alloys under the microscope, both to be able to interpret the radiograph correctly and to determine what has occurred to the metal during and after solidification. The use of a sound metallographic technique is'particularly important in developmental work and research connected with these bearings.Polishing TechniqueCopper and lead are practically immiscible in the solid state, but whilst they are miscible only in certain limited proportions in the liquid state; consequently "alloys" of copper and lead consist of a mixture of the constituent metals. The metallographic difficulties are obvious. Copper is a relatively tough metal, although it readily scratches, whilst lead is extremely soft and easily deformed. It wouId be expected if any normal polishing technique were applied that the lead would be readily torn out of the surface being prepared, and, in addition, that the lead would tarnish very easily.Grange(2) has described a method by which these difficulties can be overcome. The method involves an etch-polish procedure using "chrome regia" as an etchant for the copper. The chrome regia was a solution of chromium trioxide and hydrochloric acid in water. This type of etchant has been adopted, but it was found necessary to make certain changes.The method now adopted in this laboratory is as follows: The specimen (which is usually mounted in bakelite) is wet ground in a series of successively finer Hydro-Durexsil emery papers down to 60.0· grit paper.The specimen is then etched in the chrome regis, etchant (the composition of this etchant will pe discussed later) for approximately five seconds.Most efficient etching is obtained by swabbing the surface of the specimen...

Jan 1, 1944

By A E. Annels, I P. Hodkinson an, S P. Barr

Narrow vein systems represent an important source of gold, which have generally been exploited by small to medium sized companies. Their evaluation poses particular problems because of their grade and geological complexities. The determination of grade is arguably the most important activity in resource estimation, as it is generally grade and not tonnage that makes an orebody. This is particularly true of narrow vein-gold deposits whose resources are generally relatively small, though medium to high-grade (6 - 40+ g/t). They often display extreme grade anisotropy in all directions. Two grade populations are generally observed; 1) low, often subeconomic, background grades and 2) high-grades associated with discrete ore shoots. It is possible for gold to be distributed within the wallrocks as well as within the vein. Extremely high-grade values typify this style of mineralisation and require special consideration during grade estimation to determine if top cutting is valid or not. Estimation of both width and accumulation in 2D on vertical longitudinal projections or inclined planes have historically been used to evaluate narrow veins. Resource estimates based on traditional 2D methods is still widespread, but has in some cases been replaced by computer-based 3D modelling. Grade estimation methods are well-known, ranging from classical to geostatistical. Historically, classical methods such as inverse distance weighting have been used, though geostatistical indicator kriging methods are sometimes applicable. Geostatistical studies are driven by the production of reliable variograms, which in narrow gold veins is often problematic. It is generally difficult to define resources from drillhole intersections beyond the inferred and indicated categories with any confidence. In the majority of cases underground development is required to define measured resources and ore reserves. Trial mining/bulk sampling is often used to test estimated grades and also provides important data on ground conditions and the parameters relating to the proposed mining method required for ore reserve definition. Regular reconciliation should be undertaken between the estimated stope grades, grades indicated from stope/truck sampling and grades realised in the mill in order to determine whether correct evaluation strategies are being applied. The important feature of narrow vein-gold deposits is their strong geological controls; in response to this, geologists must understand the geology as best as possible.

Jan 1, 1999

By K H. Esbensen, A Arkenbout

In the north of the Netherlands, in the environment of Harlingen, an industrial waste incinerator was installed in 2011. The population in the region is concerned about adverse health effects related to possible emission of dioxins. This study compares the relative merit and reliability of four sampling approaches aimed at quantifying the possible pollution patterns surrounding the incinerator: short-term versus long-term isokinetic flue gas sampling, spatial sampling of grasses and a novel approach developed by the Toxicowatch Foundation, based on local composite sampling of ten eggs from backyard chickens (local area pollution load averaging by accumulating bio-entities). Based on the latter approach results of a new analytical bioassay, DR CALUX®, from 15 locations near Harlingen harbour show distinct above-threshold dioxin levels in the environs of the incinerator. Currently only short-term flue gas sampling is mandated by the authorities; based hereupon, under normal operating conditions, the incinerator appears to be compliant with emission standards. This short-term sampling scheme is seriously flawed, however, in that it only demands one continuous 12-hour sampling period per annum – an extreme grab sampling transgression in the time domain. In starkest possible contrast, significantly elevated dioxins emissions were measured in flue gas during events of unstable combustion conditions by continuous long-term measurements. The dioxin congener patterns from long-term flue gas sampling show similar patterns as the congeners found in backyard chicken eggs and grass, evidence that elevated dioxins in eggs is due to emissions from the incinerator. These results make it mandatory to perform long-term, continuous measurements for all sources where similar high-temperature combustion/emission processes take place. Backyard chicken eggs are a prevalent regional bio-accumulating sample type in rural and agricultural regions, which is relevant to air pollution emission monitoring. There are interesting relationships between this type of sampling bio-sensors and the special bioassay DR CALUX® features, which, although quite outside traditional contexts, never-the-less all can be well understood in the context of the Theory of Sampling. We venture to unravel the complex interactions between correct and incorrect sampling errors and the extraordinary complicated analytical issues involved in monitoring and source tracking using accumulating bio-sensors. The present contribution is but a first foray indicating the general total sample error scope and total analytical error framework needed for this approach.CITATION:Arkenbout, A and Esbensen, K H, 2017. Sampling, monitoring and source tracking of dioxins in the environment of an incinerator in the Netherlands, in Proceedings Eighth World Conference on Sampling and Blending , pp 117–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By T M. El Hajj, A C. Chieregati, M T. G C Marques, J M. Braga Jr, H Delboni Jr

"The estimate and control of sampling errors is essential for all mining operations, especially when dealing with strategic materials, such as niobium. This paper is based on a traditional quality assurance and quality control technique used to confirm mineralised intersection zones, and proposes the validation of sampling data using diamond drill twin holes, in order to evaluate and improve the quality of the current data set. The geological model of the niobium mine – located in Araxá, Minas Gerais, Brazil – was built including 77 diamond drill holes of a sampling campaign carried out during the 1970s. There are few records about the collection and preparation procedures of these past samples, making it difficult to estimate the errors associated with their analytical results. Therefore, 11 twin drill holes were drilled to compare their samples against the samples from the 1970s drilling campaign. The new hole locations were chosen as near as possible to the old holes location. The JORC Code, 2012 edition, relates the use of twin holes as a good sampling technique to assess sampling and assay data. Three parameters were considered to validate the 1970s drill hole campaign by the twin drill hole campaign: the difference of the coordinates between the paired holes the difference among the positions of the geological contacts to validate the geologic description the difference between the paired samples grades was calculated to validate the analytical results.The analysis of the grade range variation between sample pairs was based on three techniques: geostatistical interpretation of vertical semivariogram to obtain the nugget effect calculation of the relative difference between duplicates calculation of the error associated with the sampling protocol established according to Pierre Gy’s Theory of Sampling.The results were satisfactory for hole coordinates; however, the ore content showed a high deviation, although this divergence can be explained by the nugget effect. For the lithological intervals, the new results contributed to an effective identification of variations among lithologies, ie brown weathered ore and saprolite. The twin drill holes campaign successfully validated the geological model data, allowing effective mine planning and higher reliability of the reconciliation results.CITATION:Marques, M T G C, El Hajj, T M, Braga Jr, J M, Chieregati, A C and Delboni Jr, H, 2017. Theory of Sampling and geostatistics for twin drill holes analysis in a niobium mine in Araxá, Brazil, Australia, in Proceedings Eighth World Conference on Sampling and Blending, pp 97–106 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

Recent developments in diamond drilling practice have been chiefly 'concerned with modifications in drill design and 'operating technique whereby an increase in daily footage rates and reduced footage costs have been achieved without any marked improvements in the recovery of core. This trend is perhaps due to the general acceptance by the mining and drilling engineer alike of the belief that diamond drilling has definite limitations in exploratory work on mineral deposits characterized by irregularities in continuity and grade, such a belief arising from the fact that drilling technique has not yet evolved coring devices to ensure the full recovery of the rock and mineral formations penetrated.Current diamond drilling operations at Moonta and Wallaroo Mines, carried out by the South Australian Department of Mines, have attained remarkable results in completely eliminating core-loss by the use of a special double-tube core barreI.It is considered that assays of borehole samples taken with this special barrel have a reliability comparable, if not superior to that of similarly situated mine samples and, provided they are spaced satisfactorily, can be used as, a basis for calculating tonnage and grade. Formerly, with only partial core-recoveries, positive borehole results on narrow irregular lodes, such as those in the Moonta and Wallaroo Mines, could be accepted mainly as indications of the presence of mineralization, and could have only a limited bearing on estimates of ore reserves.The value of this special double-tube core-barrel lies In the fact that it guarantees good core recovery and, therefore, good samples, and eliminates the need for sludge-sampling, which is prone to give unreliable assay results from several causes, such as gravity concentration in the bottom of the hole and return water losses which cannot be overcome.In view of the increasing demand for minerals and the probability that the search for them will be carried on largely by boring, it is felt that it would be of interest and value to direct the attention of mining engineers to core-recovery results obtained by diamond drilling plants in South Australia and the features of the special core-barrel, designed by the writer, which has made this possible. Also, the writer is desirous of placing on record two other core-recovery devices designed to extract accurate samples in relatively soft or unconsolidated formations. The latter are used with percussion and calyx plants, respectively and their value has been proven on phosphate rock and coal deposits in South Australia.

Jan 1, 1943

By P Duplancic and C R Lilley, R Hudson, D Beck

For deep block and panel caving mines, undercut or extraction level instability can have as much impact on overall recovery as underbreak or the premature ingress of waste. If the area of the mine affected by excessive convergence is small, recovery is usually possible. However, there are several examples of entire blocks that were abandoned prematurely due to footprint collapse. Clearly, such global instability has a major impact on recovery and must be avoided – this is one of the essential tasks for the design team.The design problem is complex. The planning engineer must ensure that the footprint has sufficient capacity to withstand the maturing loads in the cave, accounting for the effects of stress path, geological structures and the rock mass conditions. These are often uncertain and only sometimes quantified.The demand on the footprint will also be influenced by decisions and actions taken during production, especially related to draw, which can worsen a developing problem. Perhaps most importantly, the design decisions that favour stability and lead to lower deformation also negatively impact on idealised cave flow. Many engineers aim to minimise the size of extraction level pillars, to improve theoretical future resource recovery but in fact this can reduce recovery if widespread deformation ensues due to the undersized pillars.In 2014, PT Freeport Indonesia undertook detailed numerical analysis to quantify the effects of variability in rock mass conditions and geological structure on overall footprint performance. The analysis accounted for a range of stress paths and maturing cave loading scenarios sourced from a calibrated whole-of-cave deformation-flow model. The intent was to replicate some of the diversity and distribution of pillar deformation outcomes that may be seen in practice at Freeport.The discontinuum finite element analysis was able to replicate damage localisation around persistent structures, a realistic distribution of drive deformation and show how small areas of instability can evolve into major problems if poorly managed. The limits of pillar size and ground support as solutions to a number of different instability problems was also investigated, showing that pillar size alone was not a sufficient remedy for all adverse circumstances.In this paper, we describe the workflow for numerical analysis of footprint deformation. We discuss the compromises and considerations for balancing the sometimes competing needs for efficient extraction levels pillars, ground support and prudent draw strategy.CITATION:Beck, D, Hudson, R, Wilson, A D, Duplancic, P and Lilley, C R, 2016. An investigation of factors affecting the long-term reliability of extraction level pillars in deep block and panel caves, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The following data cover a phase in the systematic testing of gold deposits which does not appear to have been specificalIy investigated.In boring either secondary or primary deposits, gold, by virtue of its high specific gravity, will tend to migrate downward, below the driving shoe or bit, and thus cause misinterpretation of value unless final recovery Can be effected after the hole has been bottomed.Unlike fortuitous and non-recurrent errors, due to, say, running ground, "pile driving" or rock fractures, systematic error due to migration may be unpredict.able from operating data alone, and, therefore, result in serious miscalculation of the weighted average upon which the engineer's recommendation is based.Applied to diamond drilling, loss by downward migration appears to have been largely responsible for distrust of sludge assays in the past. On the other hand, although modern practice rightly trends towards an integration of both core and sludge samples in borehole valuation, the possibility of systematic loss must be investigated when using combination graphs such as those of Longyear, Moehlman and WeIler. If the sludge value is incorrect the combination graphs will serve solely to stultify the core valuation.It appears to be axiomatic that: 1. With full core, sludge assays are of minor import.2. With recovery above 90%, differentjal grinding, of the high grade sections may have occurred, and this c!ln be corrected only by the us.e of cOJ;rect sludge valuation.3. With core recovery less than, say, 70%, no accurate valuation is possible without integrating the sludge assay.4. With less than, say, 10% core recovery, the sludge assay affords the sole basis of evaluating a borehole which may have cost many hundreds of pounds.The conditions demanded for reliable sludge valuation have, in practice, been restricted to high quantitative recovery and return of nearly 90% of the drill water. It is submitted, however, that the following additional knowledge is required:1. The nature of gold distribution in the ore.2. The lifting power of the return water column, which can be gauged by the maximum quartz particle, provided that the degree of "hindrance" can be determined.3. That all gold has been cleared from the bottom of the borehole immediately after it has passed through the orebody.The three cases discussed hereunder are offered not only as proof of the thesis, but also in the hope of promoting discussion on the interpretation of borehole values and on methods for saving free gold in the sludge. The fact that two of them cover alluvial boringand the third diamond drilling has resulted in this attempt to reduce the behaviour of free gold to a basis common to all types of boring.

Jan 1, 1950

The term geochemistry - chcmbtry' of the earth - is almost limitless in its implied subject, but of recent years a major trend of research in this field has been towards economic application in the search for mineral deposits, and in particular for those of some ofthe less common elements for which a demand now exists.Geochemistry is in a state of slow transition from a purely descriptive subject to a fundamental science concerned with the relationships that exist between the distribution of the elements in the earth's crust and the physical characteristics of the atoms of those elements. The progress achieved promises a set of basic principles which will relate the atomic characteristics of an element to the physico-chemical conditions that make for its dispersion or concentration. This means that, given a geological map of an areasufficiently detailed for the physico-chemical conditions existing in past geological eras to be deduced, there is the possibility that the relative distribution throughout that area of any element present, and its likely mode of occurrence, could be predicted from a consideration of its atomic characteristics.Since the atomic characteristics of the elements are becoming increasingly well defined by physical research, the attainment of this ideal of prediction depends upon:(a) the strengthening of geochemical theory; and(b) the development of petrological and mineralogical methods of assessing the conditions of temperature and pressure prevailing in geological formations at various stages in their history.The other prime requirement is a d.etailed geological map - a requirement that is all too often lacking.The fact that there has been very little "geochemical approach" to problems of economic geology in Australia should not be taken to mean that there is little point in trying to develop such an approach here in as active and as rigidly scientific a manner as possible. The degree of success that has attended the attempts so far made, to which reference is made below, suggests the reverse, particularly in view of the relatively slight cost involved if the investigations were properly organised on a centralised basis. There are three aspects of geochemistry that are directly applicable to the search for economic minerals.(a) The classic technique of the prospector can be made more sensitive and reliable by the use of modern equipment coupled with the application of geochemical theory to geological and structural data. The case of the rare alkali elements (see below) is givenhere as an illustration of the way in which the distribution of elements can be predicted from the first principles of geochemistry, thereby replacing the prospector's dependence on his "sixth sense" that enabled him to suggest that a certain area of formation was"favourable" for the occurrence of a certain type of mineral deposit.At its best, this sixth sense amounted to an almost subconscious correlation of all relevant associations and typical occurrences of the particular mineral experienced by the prospector during his...

Jan 1, 1950

In gold ores, the range of value disclosed by ordinary mine sampling is very wide, and the number of 'samples required for a reliable average is correspondingly great. Even where a large number of samples is available the weighted mean value of the samplesalmost invariably exceeds the true gold content. In operating mines this disparity is overcome by arbitrary reduction of high assays until reconciliation is achieved, but it is frequently necessary, especIallyin exploration, to base an estimate or to reach a decision on a relatively small number of samples from underground openings or even on a few drill hole intersections. In these circumstances, a decisive influence may be exercised by the weight allowed to high assays and to low grade intersections, both of which events are, of course, dependent on the metal distribution in the ore. Where sufficient data are available, statistical analysis will measure the risk involved, but as this information is seldom to be had, the final choice becomes largely a matter of personal judgment.With this problem in mind, a study was made some years ago of the distribution of values in four Western Australian gold ores, with the primary purpose of learning from actual ore-bodies of differing types, something of the metal distribution in the smallquantities of ore involved in individual routine mine samples, and of the importance in each case of high assays. Adequate and suitable data were available in .four cases, in three of which high assays were of frequent occurrence due to the presence of free gold. The results give concrete expression to well known differences of metal distribution, and it is proposed, firstly to record the observed distribution; secondly to examine some of the consequences of the differences in the distributions limd thirdly, to comment, in the light of this data, on the vexed question of the treatment of high assays. Standard statistical procedure was employed in the compilation of the data. The assays were classified by value into groups, each group covering a range of value of 1 dwt. per ton. Assays of less than 1.0 dwt. per ton form the first group; assays equal to or greater than 1.0 dwt. and less than 2.0 dwt. comprise the second group; those equal to or greater than 2.0 dwt. and less than 3.0 dwt. appear in the third group; and so on. Where the number of samples is large, it can be assumed that the mid-value of the group is the mean value of all the samples in the group, thus the mean values of the first three groups are 0.5 dwt., 1.5 dwt. and 2.5 dwt. respectively.The number of samples in the group is the frequency of the group, but for convenience of plotting this frequency is converted into percentage of all the samples in the series. Plotting percentage frequency as ordinate against dwt./ton as abscissa results in a frequency curve-a curve showing the frequency...

Jan 1, 1950

By S Morgan, A Jakowetz, S Taylor, B Weekes, S Litson, P Bourke, T L. Do

In the current tough mining environment with lower commodity prices, operators need to improve operational profitability. Optimised equipment asset management is a sustainable way to achieve this objective. The increased efficiency of installed process equipment positively contributes to the circuit performance, affecting metallurgical performance, plant availability and operating costs. Nui Phao Mining Company Limited (NPMC) operates a polymetallic mine located in Vietnam. The circuit produces four main products, tungsten, fluorspar, bismuth and copper. Tungsten is the major revenue producer. The operation experienced the following equipment inefficiencies in its copper and bulk sulfide flotation (BSF) circuits:• lower than expected metallurgical performance - the BSF rougher flotation tails contained coarse (+106 µm) sulfur minerals which affected the downstream tungsten gravity circuit. The unrecovered sulfur competed with tungsten minerals affecting both tungsten recovery and product grade. • structural integrity and safety - the flotation circuit structures experienced excessive vibration beyond the acceptable tolerance levels. The vibration was attributed to the flotation mechanism design and impeller tip speeds. • equipment reliability and wear life issues - the flotation mechanisms were being replaced every six months, with reported failures at three months. This resulted in high operational costs. A mineralogical evaluation of the ore indicated that the coarse sulfur minerals were well liberated and relatively rich in pyrrhotite and pyrite. It was predicted that these particles should be recoverable by flotation under optimum conditions. NPMC worked collaboratively with Outotec to investigate options to improve the metallurgical performance of both sulfur and tungsten. A review of the copper and BSF rougher circuit infrastructure was also undertaken and focused on reducing the structural vibration and improving mechanism wear life. Prior to the circuit upgrade, laboratory and pilot testing was conducted to validate the circuit improvements. The final solution included the installation of Outotec FloatForce® mechanisms in the existing copper and BSF rougher circuits, and a new flash circuit (SkimAir®) treating the rougher tails stream ahead of the tungsten gravity circuit. The flash circuit is unique, as typically these types of cells are installed in grinding circuits. By March 2016, all circuit upgrades were complete, however the initial metallurgical performance was below expectations. NPMC and Outotec worked together to investigate and improve performance through further equipment modifications. Since October 2016, the metallurgical performance has improved significantly. Coarse sulfur mineral recovery has improved, resulting in an overall increase in recovery of sulfur and tungsten of 4.7% and 2.7% respectively. The Outotec FloatForce mechanism has also delivered operational benefits, with a reduction in structural vibration to within acceptable levels (<4.0 mm/s) and an improvement in mechanism wear life by 150%. This paper discusses the BSF circuit upgrades and compares operational data before and after the upgrade to quantify the improvements in metallurgical performance, structural vibration and mechanism wear life. CITATION:Morgan, S, Weekes, B, Jakowetz, A, Litson, S, Taylor, S, Do, T L and Bourke, P, 2017. Nui Phao mine – flotation circuit upgrade, in Proceedings MetPlant 2017, pp 230–253 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By M Wimmer

LKAB operates two underground iron ore mines located in the northern part of Sweden, both using sublevel caving (SLC) as the mining method. Knowledge of the mechanisms of gravity flow is important since it affects both ore recovery and waste dilution. This paper describes results from a large-scale field test carried out at the Kiruna mine with a focus on gravity flow. It is part of Work Package 2 in the I2Mine project financed by the EU. A total of ten rings were blasted. Smart Markers based on radio frequency identification technology were used to monitor the gravity flow. An accurate delineation of the isolated extraction zone requires reliable detection of all recovered Smart Markers and precise knowledge of the 3D position of the markers within the burden. It was therefore necessary to carry out borehole deviation measurements (collar, alignment and trajectory). The blast performance was monitored by high-speed filming, near-field vibration monitoring and velocity of detonation measurements. Three-dimensional stereo images were taken from the drawpoint and the loaded bucket after each mucking cycle. Based upon that, fragmentation was assessed both in 2D and 3D. Furthermore, volumetric differences were determined at the drawpoint, which reflects the mobility of loaded material. For draw control, the Fe content is estimated by measuring weight and assuming a full bucket. The measured volume of rock in each bucket further improves this estimate. Possible flow disturbances occurring at the drawpoint were revealed by video recording. Two-dimensional laser scanning was carried out during mucking to track the position of the bucket and estimate the position and slope of the muck pile.The results from this test clearly show that the gravity flow in the large-scale sublevel cave in Kiruna mine is often of disturbed character. Standard draw occurred only in three rings and shallow draw in the remaining seven rings. In five cases, shallow draw developed towards standard draw, but occurred at rather late stages during extraction (70–125 per cent). The maximum width of the draw varied between 10 m and 13 m except for one ring (6 m). The draw reaches the cave rather early (5–25 per cent extraction) in shallow draw situations and much later (about 50 per cent) during standard draw. Waste originates from above in most cases, while more significant portions often occur at about 20–45 per cent extraction.All the results from this extensive field test are not yet fully analysed, and further field tests are planned. A more detailed insight into gravity flow in large-scale SLC and possible influence by drilling, blasting and the mucking procedure is expected in the future.CITATION:Nordqvist, A and Wimmer, M, 2016. Holistic approach to study gravity flow at the Kiruna sublevel caving mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 401–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By B Watson

The ConSep ACACIA Reactor is a device, which utilises a high intensity cyanidation process to achieve very high, usually near total, recovery of gold from gravity concentrates. The process utilises a fluidised bed and a chemical oxidant to enhance the gold dissolution kinetics to the point where the bulk of the dissolution occurs in a few hours. For convenience and security, most plants operate a 24-hour turn around. The product from the process is in the form of cathode gold ready for smelting by traditional means. The ConSep ACACIA Reactor performs a two-fold role. Firstly it increases gravity gold production, leading to a decreased CIP feed grade. Secondly, it removes slow leaching components from the plant leaching circuit. This two fold benefit leads to the following efficiencies: enhancement of the dissolution kinetics; enhancement of the adsorption kinetics; reduction of the gold load reporting to the carbon; a significant reduction of the ægold in circuitÆ lockup; and removal of slow leaching entities which can also result in a lowering of the required cyanide concentrations in the leaching circuit and a subsequent reduction in overall cyanide consumption. The above benefits are discussed in this paper, with a particular focus on the ConSep ACACIA ReactorÆs role in removing slow leaching components, with data generated over a 21-month period. Improvement in overall plant recovery via removal of slow leaching gold species is achieved in two ways. Firstly, some of the slow leaching entities, successfully leached under intensive cyanidation, are not always fully leached under plant conditions. This results in a lowering of the solid tailing. Secondly, the faster leaching kinetics achieved in the plant as a result of the removal of slow leaching entities results in faster and more complete adsorption of the dissolved gold onto activated carbon. This results in a lowering of the solution tailings. The construction and operation of the ConSep ACACIA Reactor is simple. Apart from the reactor body, which is a proprietary design, all components of the system are æoff the shelfÆ or specific to the siteÆs requirements. In operation of the fully automated version, a PLC controls a series of valves and pumps but except for a daily changeover process the only operating component for the bulk of the time is a relatively small solution pump. The process can be totally automated giving the security of a æhands freeÆ concentrate handling process up to the point where the product is presented as cathode gold. The ConSep ACACIA Reactor was developed by Anglogold Australia (formerly Acacia Resources) for Union ReefÆs Gold Plant and has been in production since February 1999. It has proven to be a low cost, high recovery, mechanically reliable method for the processing of gold concentrates. Such has been the success of the plant, as of June 2003 there are eighteen full installations of the processing plant installed at mines owned and/or managed by Anglogold, Newmont, Placer Dome, Independence (formerly Lonrho), Sons of Gwalia and Harmony.

Jan 1, 2003

By C De-Vitry

"The large Yandi channel iron deposit (CID) is located in the north-west of Western Australia and is currently mined via open pit methods. Drilling at Yandi is widely spaced and current estimates are mostly linear averages of the surrounding local samples. Linear estimates such as ordinary kriging (OK) based on block sizes that are significantly smaller than the dimensions of the drilling grid are less variable than the unknown reality (Armstrong and Champigny, 1989).Conditional simulation (CS) provides a series of plausible realisations that represent the actual grade variability at a small scale (eg 1 m + 1 m + 1 m). These simulations are very useful for a number of purposes, eg: optimising grade control, stockpiling and blending selection of optimal drill hole spacing assessing resource risk on contained tonnage and metal.At Yandi the major constituents of the ore (Fe, P2O5, SiO2, Al2O3 and LOI) are correlated to varying degrees. Independent CS of each assay variable will not reproduce these correlations. Reproducing the correlations (and the shape of scatterplots) is important if the simulations are used for the abovementioned purposes. This paper examines and compares various methods of CS that aim to reproduce the correlations between the assay variables.The CS methods evaluated in this paper are conditional co-simulation (CCS) using the linear model of co-regionalisation and two other, alternative multivariate simulation methods, which use min/max autocorrelation factors (MAF) or the stepwise conditional transform (SCT) to de-correlate assay variables before performing independent CS. It was found that CCS best reproduced the characteristics (histograms, variogram, scatterplots, etc) of the declustered drill hole data (Figure 1). Whilst simulation using MAF generally produced acceptable results, the method did not adequately reproduce the variance of the assay variables. The univariate statistics, histograms and experimental variograms were acceptable for simulations generated from the SCT. Bivariate statistics, cross-variograms and scatterplot reproduction for the SCT were unacceptable. The latter method produced inferior results because there were insufficient samples to obtain a reliable transform of the third assay variable in the transformation sequence.None of the abovementioned simulation methods provides good reproduction of all the scatterplots. This is due to the presence of clay pods, which cause some scatterplots to display two trends. These clay pods contain higher percentages of SiO2 and Al2O3 than the surrounding CID. The clay pods are generally smaller than the drill-grid dimensions. Thus their locations are typically unknown and they cannot be defined by manual interpretation, eg via wireframes. The locations of the clay pods were simulated via indicator CS. CCS was then performed separately for the clay pods and the CID. This significantly improved the reproduction of the correlation coefficients, the scatterplots and visually the simulation was more geologically realistic. Simulating the location of clay pods followed by CCS of assay variables is the recommended approach for simulation at the Yandi CID.CITATION:De-Vitry, C, 2013. Simulation of correlated assay variables - a case study from the Yandi Channel iron deposit, in Proceedings Iron Ore 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By P Goblet, S A. Séguret, E Cordier, A Galli

In salar-type deposits, lithium grades can be measured by bailers introduced at different elevations in the drill holes at locations where, later, the brine will be pumped out to recover the metal. When they are duplicated, these a priori rudimentary measurements may show large differences without indicating whether this is due to the procedure itself or to some physical causes linked to the dynamic behaviour of the salar (seasonality, rainfall, underground flow etc). In the reservoir presented in the paper, the problem is complicated by the double lack of stationarity of the lithium grades: the grades not only increase importantly with the depth but at the same time their fluctuations decrease, making it necessary to use non-stationary geostatistical techniques to simulate them. Reservoir simulation is developed in two steps: first, geostatistical simulations of the lithium grade create possible realisations of the reservoir; then, each geostatistical simulation is followed by a pumping simulation that calculates, at each drill hole of a given extraction scenario, the lithium produced each year over 40 years. For the set of 100 simulations produced in this way, a scenario reduction is made to choose the five most representative simulations where more complex calculations will be carried out (for example, changing hydrogeological parameters such as porosity and permeability, or the elevation of the filters, the number and the location of the pumping and the reinjection drill holes etc). The paper first presents an analysis of the geostatistical model sensitivity to the grade uncertainty when measured by bailer. Among the 100 measurements at our disposal covering the future production domain, 50 per cent are duplicates measured at the same place but at different times. They are randomly sampled to produce five subsets of 75 values, which will constitute the future 3D conditioning points for the geostatistical analysis and the simulations. For each subset, trend, standard deviation and variogram models are fitted, leading to five sets of 20 geostatistical simulations of grades. In this way, the reliability of the different parameters involved in the procedure is evaluated, as well as its impact on the pumping results. Then, a reconciliation study is conducted between the non-stationary nugget effects encountered in the 3D variograms of the lithium grade and a pure statistical analysis of 25 duplicates measured at different locations and/or different times. The result is that if the nugget effect reaches 20 per cent, which is the case of three conditioning subsets out of five, the reconciliation is good and the nugget effect of the variogram model represents the bailer uncertainty, ie the measurement error. Since the geostatistical simulation incorporates a nugget effect, it handles the bailer uncertainty and the impact on the produced metal is included in the evaluation. The final conclusion is that, after the hydrogeological pumping simulations, the initial differences between the five geostatistical models do not influence the final results: lithium grades measured by bailers can lead to a robust evaluation of the extractable resources, a conclusion that conflicts with conventional wisdom.CITATION:Séguret, S A, Goblet, P, Cordier, E and Galli, A, 2017. Bailer uncertainty evaluation in a lithium salar deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 395–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Sluiceboxes can provide a much higher concentration ratio than most other gravity concentrators (up to 50 000:1) at very high overall placer gold recoveries (greater than 99 per cent). They are also very reliable, inexpensive and simple to operate. This combination is very difficult to beat and explains why the sluicebox is still the most important placer gold concentrator in northwestern Canada, Alaska and the rest of the world. A sluicebox is a rectangular fl ume containing riffles on matting, through which a dilute (<12 per cent) slurry of water and alluvial gravel flows. Sluiceboxes are actually centrifugal concentrators with settling velocity playing a minor role in gold recovery. Due to their higher density, gold particles tend to segregate to the bottom of the slurry flow where they form a streamline that is diverted by a low pressure zone into a riffle. Under ideal conditions, this ribbon of slurry will be overturned as it flows down the rear of the following riffle and will continue fl owing in a circular path to form a vortex. At the bottom of this vortex, centrifugal and gravitational forces combine to drive gold particles into or beside the matting. To remove the gold concentrates, sluiceboxes are shut down and the riffles and matting are taken apart and cleaned. The slurry velocity provides the energy that powers the vortex. If the velocity of the slurry is reduced through overloading with solids, insufficient water flows or shallow gradients it may not sustain a full size vortex. If the riffles are too close, too far apart, too tall, or if there is not enough energy available to the vortex, the vortex will not be formed properly and gold recovery will be reduced. If the slurry velocity is too high, extreme turbulence and the resulting scouring will also cause gold losses. Testing sluiceboxes with conventional sampling and evaluation techniques is very costly, time consuming and problematic. Most placer gold ores contain a very small number of gold particles in a large volume of pay gravels. Sluiceboxes can lose coarse gold particles. The presence or absence of one of these particles in a tailings sample can lead to high unpredictable errors (nugget effect) even when large sample volumes are processed with care. Every time conventional samples are upgraded, additional errors are introduced due to the inefficiency of recovery equipment. Nuclear tracer tests are more accurate, faster, cheaper and safer than conventional sampling. In 1989 through 2002, the recovery efficiency of dozens of sluicing systems was determined by mixing radioactive gold particles (tracers) into the feed streams of dozens of placer mines in the Yukon Territory, British Columbia, Alaska and Guyana. Four distinct sizes of nuclear tracers were used and their recovery was related to the design and operational characteristics of the individual sluiceboxes and their pay gravels. At clean up, scintillometers were used to detect the very low level X-ray and gamma ray radiation emitted by these tracers and locate them in the sluice runs. The effectiveness of any given section of riffles was easily diagnosed by the presence or absence of tracers. At every mine the gravel feed rates, water flows, equipment dimensions and riffle performance were measured. After the gold tracers were removed from the fi nal concentrate and counted, the concentrate was sieved and weighed. These gold recovery, weight and sieve data were used to calculate the quantities and size distributions of the gold particles in the original pay gravels and those lost in the tailings. The expired tracers were stored in a lead lined container until their radioactivity was near background levels (about two months). The standard errors from these radiotracer tests were estimated from binomial probability theory with the equation: SE = {(n + p + q) ^ 0.5}/n. Where n was the total number of radiotracers added, p is the proportion recovered and q was the proportion lost. Each overall recovery estimate would be within one standard error of the true recovery value (14 times out of 20) and almost always within two standard errors of the true recovery (19 times out of 20). The maximum standard error with 100 tracers was five per cent and occurred when the recovery approached 50 per cent. With higher recoveries, standard errors usually ranged from one to two per cent.

Aug 1, 2010

Alluvial gold grades are typically highly erratic. It is very often difficult to establish with confidence the in situ grades of reserve blocks due to the small number of pit or drill hole samples available, and their erratic values. Trends in grade are often obscure. Geostatical methods are inappropriate due to the extreme nugget effect found in alluvial gold field data. Classical statistics appear more suited to such data but require assumptions to be made regarding the nature of the population sampled. Recent developments in computer intensive non-parametric statistical methods provide a new approach to dealing with some of the above problems. These methods avoid making assumptions about the type of population distribution, usually through some kind of re-sampling scheme. The bootstrap procedure involves taking the estimate of interest and synthesising its population of by re-sampling the original data a large number of times (1000+), at random and with replacement. The synthetic population is then used to draw conclusions about the likely behaviour of the true population.

Jan 1, 1985