Search Documents

By X X. Qiu, T Zhang, B L. Wang, X Qiu, Y H. Du

This paper summarises the information about current state of eco-environmental problems, geological disaster and mining waste causing during the process of limestone mining. By comparing the management experiences of limestone mines in other countries, management problems in China have been discussed and improved management options have been proposed here. These options include: accelerating the process of legislation, promoting and strengthening environmental impact assessment for limestone mine, and increasing compensation requirements according to the local eco-environment conditions.CITATION :Wang, B L, Qiu, X X, Qiu, X, Zhang, T and Du, Y H, 2012. Eco-environmental problems caused by the process of limestone mining and management options, in Proceedings Life-of-Mine 2012 , pp 357-360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By I Jabou, D G. Blazak, L C. S Hogarth

The R70 test is a good indicator of coal reactivity to oxygen and is commonly used to provide a rating of propensity for self-heating. Tests performed by The University of Queensland Spontaneous Combustion Testing Laboratory have resulted in the development of a large database that shows the impact of coal quality on this parameter. From these results it is possible to infer an R70 value, which can be used to gain an appreciation of the intrinsic coal reactivity before it is even tested. However, any interpretation of R70 values must consider the influences of coal rank, mineral matter and moisture content to provide a better understanding of the spontaneous combustion risk of a particular coal.

Jan 1, 2005

By R Higashi, D Maruoka, T Murakami, Y Iwami

The ironmaking industry consumes a large amount of fossil fuel derived carbon as heat source, reducing agent of iron ores and carburising agent of reduced iron. Although the demand for drastic decrease of carbon dioxide emission, carbon is an essential element for smelting process of molten iron. The carbon recycling ironmaking process by circulating CO has been already proposed to achieve carbon neutrality. However, the production of molten hot metal is not considered in this process because sufficient amount of carbon does not dissolve in reduced iron by CO. Therefore, our group has suggested a new carbon recycling ironmaking process which can produce hot metal. In this process, free carbon and iron carbides produced by carbon deposition reaction using metallic iron as a catalyst are used. It is known that only Fe3C is obtained as iron carbide by using CO gas, however, Fe5C2 is also produced by adding H2 gas. The composite agglomerated with these carbonaceous materials and fine iron ore (Deposited Carbon-Iron oxide Composite: DCIC) is reduced and melted in a furnace. It is reported that Fe3C in DCIC accelerates the reduction reaction and melting of the composite. In this study, the effects of iron carbides and free carbon on the melting behaviour of DCIC are investigated. Fe3C, Fe5C2 and free carbon were produced by vapour deposition using porous iron whiskers and CO-CO2-H2 gas. These were agglomerated with hematite reagent at a certain ratio to prepare DCIC samples with and without Fe5C2. The samples were heated up to 1300°C in inert atmosphere. The DCIC containing Fe5C2 completely melted and iron nuggets were obtained after the experiment. This behaviour was not observed in the composite without Fe5C2. This indicates that using Fe5C2 is more preferable than Fe3C for molten iron production using DCIC.

Jun 19, 2024

By Cotton P. L

Although the terms "pipe" and "tube" are normally considered synonymous, a distinction is often drawn, the former term being applied to the hot finished product and the latter to cold finished material. It is, considered that the title of this paper includes hot finished seamless, and continuous-weld pipe, cold drawn seamless tubing, and electrically welded tubing.The continuous-weld process will be reviewed first, passing to the various methods of seamless manufacturing, which, in addition to meeting the demand for hot finished seamless pipe, also supply the raw material for cold drawn tubing, the manufacture of which will then be described. Finally the electric resistance-weld process will be Considered, and the paper will conclude with a brief review of the processes described and trends in present-day manufacture.CONTINUOUS-WELD PIPEThe raw material for this process is delivered in the form of coiled, hot finished, strip steel, generally referred to as "skelp". The end of one coil is electrically buttwelded to that of'the next, so forming an unbroken strip. This continuous ribbon of 'steel is fed into a skelp heating furnace, and brought to the correct temperature for the forming and welding operations which follow. This temperature is usually about 1,350°C.The heated skelp issues from the furnace into 'a multistand mill, in which the first pair of rolls is designed to form the skelp into tubular shape, the edges being in close proximity to, but not touching each' other. These edges...

Jan 1, 1951

By D Bruggemann, F Sereshki

There has been an ongoing research on coal and gas outburst for the past two decades at the School of Civil, Mining and Environmental Engineering, University of Wollongong. Research study began with a humble beginning, initially conducting basic laboratory studies on the coal and gas properties, progressing into the determination of gas content of coal by sorption technique and the effect of gas pressures on coal strength. The present laboratory facilities and research interests are extended to include the study of coal permeability and shrinkage properties and their effect of gas drainage characteristics with respect to gas type, and pressures. All the changes are examined with respect to changing in-site geological conditions of the coal deposit investigated. The aim is to provide a long-term support to industry in establishing a data bank for Australian coal deposit characteristics and properties.

Jan 1, 2005

The greater part of this paper comprises the material used in a lecture delivered to the South Queensland Branch of the Australasian Institute of Mining and Metallurgy in September, 1949. It contains little in the way of original matter, its main purpose being to call attention to the need for research into the properties of Queensland coals and to indicate some of the lines such investigations might profitably follow.Since the lecture was given the Powell Duffryn (1949) 1 report, which has made an excellent start along these lines, has been printed. This report is, however, only a beginning, though a big one, and there is ample room for many years of work along similar lines.The paper is based largely on the work of de Jersey (1946, 1949)2,3,4,5 and Jones and de Jersey (1947)6, but these workers in turn owe a debt to the work of many British and American investigators, too many to enumerate. The subject is a very large one-to deal with it fully would require not a paper but a book; all the author can hope to do is to discuss very briefly some of the main lines of investigation and indicate some of their applications.The reason for selecting Queensland coals in particular is the widespread ignorance of the extent of the coal resources of that State and the almost complete ignorance, to within the last year, of the modern industrial purposes to...

Jan 1, 1950

Copper-Cobalt hydrometallurgy has seen a resurgence in recent years with the development of projects in Zambia and the DRC. Many of the flow sheets are unique in their use of hydrometallurgical techniques to improve performance compared to the older types in current use. The emphasis has moved from direct copper electrowinning/stripping, with multiple stages of precipitation for removal of impurities and concentration of cobalt, to innovative use of solvent extraction and ion exchange with higher cobalt recoveries to final product. The poor quality direct electro-won copper has been supplanted with solvent extraction-electrowinning; with consequent production of LME 'A' quality metal. Many of the precipitation steps in cobalt recovery and concentration, have been replaced with solvent extraction; while the remaining precipitation stages have been enhanced with use of oxidants to improve impurity removal. Operating experience from two of these circuits has shown the benefits of the new technologies and the improved overall recovery of both copper and cobalt into higher quality products.

Jan 1, 2008

Some 50 miles of tunnel have been driven in the Snowy Mountains Area since tunnelling commenced in 1951. Hates have improved progressively due to the know-how of American supervision and use of large matched equipment of modern design.The work has been carried out by contractors, working almost exclusively under schedule of rates contracts. The Authority has maintained active research into tunnelling problems, especially that of support, and this has resulted in considerable economies and improved rates of progress. The contractors also have sought economies both by management and equipment techniques. Ammonium nitrate came into favour as an explosive essentially because of its lower cost, and handling techniques have improved progressively. Rock conditions preclude use of the "Mole" type equipment in its present stage of development, but one contractor introduced the "sliding floor" and this could exert a great influence on future tunnelling methods.Examination of tunnels that have been in service for some time confirmed the quality of the work and endorsed the policy of continued research and development.GENEHALThe Snowy Mountains Scheme provides for the diversion of the Snowy and Eucumbene waters through two transmountain tunnels to the western river systems. These diversions, together with additional regulations provided for waters already flowing inland, will provide an average additional discharge of 1,818,000 ac it per year for irrigation.Furthermore, approximately 6,000 million kWh of electrical energy will be generated annually in power stations with a total installed capacity of some 3,000,000 kW (Fig. 1.).INVESTIGATIONThe aim of investigation work is firstly to collect sufficient information to allow the overall scheme to be planned and then to follow up with detailed information on eachproject. The correct balance for all aspects of this work is a matter for keen judgment, as the tunnels must be planned...

Jan 1, 1963

Tunnels are being built around the world using TBMs and prefabricated segments or in situ concrete as linings. Clients demand high quality of these linings to guarantee a long-term stability and density of the tunnels. This paper describes the development and the use of segmental lining systems, including joints, important design criteria, installation procedures, possible mistakes and consequences, repair works and final results for different sites in Europe and around the world. The experience on these sites shows that damages may occur, if some essential aspects are not considered. These aspects include:parameters of the TBMs and back-up equipment such as fixation of jacking rams, movement of the back-up on the lining or ring reformer;parameters of the segments such as quality of moulds, quantity of reinforcement or structure of the joints; andparameters of the tunnel drive such as advance rate, ring-gap grouting or experience of the tunnel crew.All these aspects have to be considered very carefully in detail to get a good lining accepted in total.

Jan 1, 1999

The scheme of rehabilitation of surface plant commenced in 1936, included the provision of improved and more hygienic changing and bathing facilities for the employees.At that time the Thompson's Shaft section of the British Mine was being prepared for a resumption of operations, and it was decided to repair and re-equip the existing building. Thus any new scheme adopted could be given a thorough trial, and the proved arrangement used as a basis for the contemplated new main changehouse on the North Section.Investigations were carried out to determine the most suitable arrangement for the Thompson's Shaft changehouse, to provide for a total of 120 men, with particular regard to the internal fittings and fixtures. Also, as the mining conditions were such that a large proportion of clothes worn underground by miners, etc., were wet by the end of the shift, the problem of drying these clothes in the availaole time from a man coming off shift to his commencing again some sixteen hours later was one of the most important to be dealt with.The changehouses in use on the North mine section of the lease were provided with racks around the walls for the men to hang their street clothes on, and a section was partitioned off to house the mine clothes and their drying facilities. The actual drying was carried out by means of hanging the wet clothes over racks between which ran pipe coils heated by means of hot water circulated from the hot water boiler supplying the showers.This method had proved to be far from satisfactory for several reasons, the main objections being:-

Jan 1, 1940

By D Piason

Newstan Mine commenced mining operations in 1887 and has since undertaken extensive mining within the Young Wallsend, Great Northern, Fassifern, Borehole and West Borehole coal seams using a range of mining methods including board and pillar mining and longwall mining.Newstan Mine is planning to extend the existing mine workings using longwall and miniwall mining methods to produce up to 4.5 Mt/a of run-of-mine (ROM) coal for at least 25 years. The planned extension in the Main East and South West sections will involve developing new longwall panels and related mains headings. The new area contains higher specific gas emissions (SGE) than previously experienced at Newstan Mine. To achieve the optimum ventilation requirements for the longwall operation in this new area, a new ventilation shaft was designed to be constructed using the blind boring method in the South West Headings section.This paper presents the shaft design parameters and selection criteria for the construction of the new ventilation shaft, including the construction phase and the holing process to connect the shaft to the underground workings. The paper also discusses future ventilation requirements for Newstan Mine.CITATION:Piason, D, 2015. South-west ventilation shaft project at Newstan Mine, in Proceedings The Australian Mine Ventilation Conference, pp 229–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By M I. Pownceby, M A. Rhamdhani, S Palanisamy, D Fellicia, B Satritama, G A. Brooks, A Ang

Metal production have long been using carbon sources as both reducing agents and energy sources. Consequently, the global extractive metal sector contributes significantly to greenhouse gas emissions, accounting for approximately 9.5 per cent. Hydrogen gas offers as a promising ecofriendly alternative to carbon in metallurgical processes, serving as both a reductant and energy supplier with a by-product being only water vapour. However, the implementation of molecular hydrogen faces certain challenges related to the thermodynamics and kinetics of metal oxide reduction. In addressing these challenges, researchers have explored the application of hydrogen plasma, generated by subjecting molecular hydrogen to high energy to produce atomic, ionic and excited hydrogen species. Hydrogen plasma offers thermodynamic and kinetic advantages over molecular hydrogen and carbon-based reductants, exhibiting lower standard Gibbs free energy of reaction and activation energy. Therefore, hydrogen plasma can produce metal in fewer steps, process any oxide feed and feed size and even be used to refine metals. Despite these advantages, challenges exist in utilising hydrogen plasma in extractive metallurgy, including electricity costs, potential reverse reactions and industrial-scale implementation. This study provides a mini review of prior research on hydrogen plasma for metal oxides reduction, particularly iron oxide, as well as state-of-the-art techniques for its use in extractive metallurgy applications by mentioning several reactor types. Future prospects and scale-up possibilities of the hydrogen plasma in extractive metallurgy will also be presented.

Aug 21, 2024

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

By D Reid

Run-out analyses of tailings storage facilities are typically undertaken using methods based on rheological theory. These are reasonable techniques to model the behaviour of tailings that, through significant run-out and possibly mixing with supernatant water, are generally acting in a fluidised manner. Such modelling often follows on from two-dimensional continuum analysis models where, if failure is predicted, grid failure often occurs when deformations begin to increase. This results in a disconnect between the prediction of failure and the modelling of the potential extent of the failure.Recently, rezoning methods have been incorporated into commercially available two-dimensional soil mechanics deformation codes. Rezoning techniques enable large deformations to be modelled within a two-dimensional continuum analysis framework; however, while promising, the use of such tools is not yet widespread, and a consensus is yet to develop on how they should be applied to tailings dam run-out modelling.This paper uses FLAC rezoning techniques to model the flow behaviour of two historic tailings dam failures. The purpose of these analyses is to critically assess the performance of rezoning against some available historic failures. The required data to undertake such an analysis is outlined, along with the inherent limitations and assumptions required. Parametric analyses are outlined to address some of these issues. In general, the analyses undertaken underestimated the flow distance observed in the historic failures by varying degrees; however, in some instances, the analysis reasonably reproduced the qualitative shape of the initial failure zone. A variety of potential reasons for the discrepancy between historical observations and the models undertaken are provided.CITATION:Reid, D, 2015. The use of rezoning techniques to model historic tailings failures, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By S Dunham

For decades we’ve been focusing on reconciliation as a tool to validate mineral resource estimates. And for decades we’ve been misleading ourselves. The concept of reconciliation is simple. Predict, measure, compare and assess the quality of the prediction. This four-step process reflects the ideas of statistical process control and the plan-do-check-act cycle of Shewhart and Deming fame and our intuitive understanding of using system feedback to improve performance. In an ideal world where data is robust and dense this type of feedback loop can be useful. In the mining industry however, there are some fundamental flaws with the conceptual framework. At almost every stage of the process from pre-estimation through to final production the mining system is plagued by material challenges with data and measurement quality and quantity, system delays, and losses from a supposedly closed system. These issues can and do impact on the benefits sought from reconciliation. Instead of providing feedback leading to improved estimation, reconciliation can result in poor decisions, distracting investigations, and exacerbate the noise in an already noisy system. Before we can rely on reconciliation as a management tool, we need to address the multiple challenges present in our everyday practices. Some of the most critical issues are addressed in this paper.

May 24, 2023

Australia had been enjoying a market boom led by the mining sector and West Australian mines were leading the way to satisfy the massive demand for our natural resources, especially from China. However, the Apache gas explosion on Varanus Island, 97 km off the west coast, has clearly demonstrated how the unexpected can suddenly impact on profitability and investor confidence for the mining industry. Risk management with contingency planning can provide the most cost-effective solution to help ensure mining projects are successful. For this discussion we will focus primarily on contingency planning, CP for mining projects à and how to plan for the unexpected. The Apache gas explosion will be our example æUnexpected EventÆ. Insurance may provide financial compensation but it will not protect your reputation as a reliable supplier or prevent damage to investor confidence and future mine projects. However, contingency planning can provide real protection for mining projects à to survive the unexpected.

Jan 1, 2009

In-seam drilling is conducted mainly to drain coal of gas and/or water prior to development or extraction. The requirements of inseam drilling for gas drainage have mainly surpassed the technical limits of rotary drilling and are mainly being addressed by guided down hole motor drilling, albeit at a higher cost. There is an increasing application of in-seam drilling to detect geological structures or other hazards or their absence in advance of mining to reduce the risks of underground mining. Close collaboration between miners, drillers, geologists, researchers and suppliers over the last four years has seen many advances made to improve the accuracy and reliability of inseam drilling. With such developments will come closer control over the ventilation and safety of future mining under deep gassy conditions, but not without costs. The paper summarises the current applications of inseam drilling, recent technological advances and the next generation survey and geophysical sensing tools which are currently being developed

Jan 1, 1998

By A R. Butcher

Gold deportment and ore characterisation studies are key tools in gaining an appropriate understanding of complex gold ores for process development and optimisation. These studies have historically involved imprecise chemical methods with slow and costly optical microscopy for gold identification. The traditional approach requires highly skilled petrographers, is prone to human error, and is not scalable, reducing the usefulness in practical analysis. The proposed methodology utilises a decision tree and knowledge base in a staged approach to gold ore characterisation, building up progressively more detailed information about the sample mineralogy, gold deportment and key mineral properties, as the process is followed. Whilst the automated QEMSCAN« system is used for mineral and gold identification, interactive and focused data analyses are used to give more efficient and accurate results. This is complemented by smart sample preparation and chemical methods to enhance and validate the data, making the staged approach methodology reliable, scalable and therefore practical and economical.

Jan 1, 2007

By Y Zhang

Being analysed systematically, the factors influencing the production of fully-mechanised coal face have been divided into geological, mining technical, and management groups. Artificial neural network-expert systems (ANN-ES) are established to decide the influencing factorsÆ membership grade; genetic algorithm-artificial neural network (GA-ANN) are used to decide the weights; fuzzy comprehensive evaluation method is used to calculate the integration indexes. Finally, the GA-ANN model is established to forecast the production of fullymechanised coal face. It is proved that the model is reliable with higher precision. The production of fully-mechanised coal face is influenced by many factors. However, some influencing factors are neglected by the traditional forecasting methods, the results of which are not precise and hardly be used as a guide for mine production and management. The relation between the production of fully-mechanised coal face and its effecting factors is analysed, and the meta-synthetic AI approaches are used to forecast the production of fully-mechanised coal face.

Jan 1, 2003

By A E. Annels, M NoppT

Ore Reserves are key mining company assets and their reliable estimation is crucial for both feasibility studies and the day to day operation of a mine. The reserve is based on the Mineral Resource after the application of certain technical and economic parameters. Engineering aspects of reserve estimation can be accurately determined to ¦10 per cent, however the majority of project risk will revolve around the resource. A final Ore Reserve generally contains a set of figures quoted without reference to its potential errors. Rarely are overall confidence limits quoted and, if they are, they often do not take into account many of the factors that cause uncertainty in the grade and tonnage estimates. There is thus an unquantifiable risk, which the operator should be aware of. This paper presents a review of the possible sources of error that might occur during the various phases of an exploration and estimation programme which are carried through into the Ore Reserve and hence mine design.

Jan 1, 2002