Search Documents

By McAllister J

Oxygen was in restricted use at Port Kembla until tonnage oxygen became available for steelmaking in the open hearth furnaces. In adopting the new process various modifications to furnace design and operation were necessary and some of these, including increase in roof height and variation in firing and draft control, are discussed.The design of oxygen lances is also discussed and various steelmakingtechniques considered.Steel production increased with oxygen roof lancing-one- furnace producing 8,507 tons in one week-but new problems, such as rate of refractory wear, and disposal of fumes, were created.Design of future open hearth oxygen furnaces is predicted.INTRODUCTIONIn the post-war era, the availability of "tonnage" oxygen caused a major revolution in steelmaking techniques. Various pneumatic processes showed that steel can be madeat a very fast rate and that oxygen steelmaking can be applied to open hearth furnaces. Methods used are surface impingement with roof lances, bath injection with door lances, flame enrichment with fuel firing, mixed gas and oxygen firing, and enrichment of normal combustion air by oxygen injection into the flue systems.Owing to its previous restricted availability and high cost, oxygen was used in rather small quantities in the open hearth furnaces at Australian Iron and Steel Pty. Ltd.(A.I. & S.), Port Kembla, until about the middle of 1960.At that time tonnage oxygen became available and roof lancing commenced on No. 33 furnace at No. 2' open hearth shop.

Jan 1, 1962

Hydraulic backfill is generally retained in stopes using permeable barricades. Mitchell et al (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et al (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading conditions. This paper discusses the circumstances that led to these incidents and analyses the modes of failure. The standards for the safe operating of hydraulic backfill systems are reviewed along with requirements for ongoing management and control. The design requirements of barricade construction are analysed and some appropriate guidelines introduced.

Jan 1, 1998

By M Fewings

This paper casts a light on the sometimes murky world that lies between base metals product æout the gateÆ, and money in the bank. Whether your base metals are leaving the mine as a refined product, or as an ore or concentrate, the generally accepted method of value determination is a London Metal Exchange price, usually measured at some point after the material has left your control. In this paper, the structure and operation, regulation and the reasons for the use of the London Metal Exchange are explored. In addition, the risks and opportunities that terminal market pricing provides to mine managers are explained, with particular reference to hedging. The paper also deals with the structure of the sales contract, including management of shipping issues, agreement of delivered quality, documentation and administrative issues. The selection of counterparties, the role of traders in the market and the growing influence of China and India as base metal consumers and competitors are also addressed.

Jan 1, 2006

By Bagley A. S

The accuracy and precision of rutile analyses are discussed. Comparison is made between the wet chemical and X-ray fluorescence spectrographic methods of. estimating Ti02 in commercial rutile. Various allotropes of 'I'i02 are identified by diffractometry and a comparative analysis of the coloured varieties of rutile is given. For X-ray fiuorescence . analysis, specimen preparation is critical and sample grinding and pressures. for pellet making are discussed in detail.Cellulose bonded and backed pellets are shown to be subject to relaxation with increasing age.INTRODUCTIONTo date much of the analytical work on commercial samples has been done by wet chemical methods.This led to various discrepancies in results, which are of particular importance when certificates must be issued for overseas shipments. The present work reviews the nature of rutile and compares the results of Ti02 estimation by wet chemical methods and those obtained by X-ray fluorescence spectrographic analysis.In the rutile industry the results from different analysts and even those from the same analyst are not always consistent. To the analytical chemist this should not be surprising.Fairbairn (1951) showed the results obtained from 34 different analysts on a specially prepared sample of granitic rock. It is of some interest to note that the Ti02 content as determined by the 34 analysts using unspecified methods ranged from 0-17 per cent to 0·30 per cent. Fairbairn (1953) found that1. replicate analyses from the same analyst give a high order of precision,2. analyses by different analysts using the same procedures give reasonable precision, and...

Jan 1, 1965

By T Napier-Munn, E Louwrens, L Keeney

Geometallurgical characterisation of ore deposits is accepted practice in some parts of the mining industry today. Its primary aim is to provide constrained inputs that reflect inherent geological variability and its impact on metallurgical performance for the deposit. Geometallurgy improves project value because it suggests more valuable alternatives for scheduling and processing through an increased knowledge and understanding of the interactions of rock properties and extractive technologies. Lower project cost (both capital and processing) and improved recoveries are the result from closer tailoring of the mining and mineral processing strategies to the characteristics of the resource (Dunham, Vann and Coward, 2011). Tailings storage facilities (TSFs) can be seen as potential resources and it is argued that fundamental geometallurgical characterisation as applied in ore deposit characterisation should also be applied to planning the retreatment of TSFs. This paper will describe a research project at Julius Kruttschnitt Mineral Resource Centre assessing if geometallurgical principles and methodologies can successfully be applied to TSFs as they have been to primary deposits. The project is establishing a new standard method of tailings evaluation which will include a 3D spatial model of the tailings resource. Initial domaining of the TSFs was done using principal component analysis followed by k-means cluster analysis based on chemical assays from drill core samples. The subsequent characterisation of the drill core samples has involved chemical, mineralogical and metallurgical profiling, with a range of metallurgical tests being conducted on the samples. This characterisation step is followed by class-based analysis, predictive modelling and process performance domaining with the ultimate objective of establishing a 3D spatial model incorporating geochemical, mineralogical and metallurgical performance data. This approach, which takes into account processing performance permits a more realistic (as compared to doing limited chemical assays and metallurgical testing) economic evaluation of the potential of reprocessing the tailings material. It is believed that the approach is generic and can be applied to other TSFs being considered for reprocessing. The present case study has also established the gold, copper, magnetite and cobalt deportment for an iron oxide copper-gold deposit tailings resource.CITATION:Louwrens, E, Napier-Munn, T and Keeney, L, 2015. Geometallurgical characterisation of a tailings storage facility – a novel approach, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 125–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Alexieva

Since the early 1900s the geotechnical community has investigated every significant failure of a tailings dam, improved our knowledge of the behaviour of the tailings storage facilities, developed analysis methods, compiled lessons learned, and committed to zero failures. The rate of occurrence of tailings dam failures has reduced since the 1980s, however, failures continue to occur and continue to surprise us. At BHP, we have decided to take an approach to the tailings management that is similar to the approach to safety. We are looking at ways to eliminate, substitute, separate or engineer around the hazard (tailings dam failure). As such, our ultimate long term goal would be to eliminate the need for new tailings facilities. Unfortunately, we have not developed yet technologies for extracting many of the common metals and minerals without producing tailings. Our shorter term goal is to substitute the current conventional slurry tailings facilities with less risky dryer facilities. We are working with vendors and research organizations to develop technologies that can be efficiently applied on a large scale. At the same time, we are committed to using the best available engineering to reduce the risks associated with our existing and new conventional tailings facilities. The best engineering can be achieved by people with the appropriate education, experience, attention to detail, discipline and authority. We have implemented a system of governance to make sure, we have the best engineering applied to all our facilities, considering the specific conditions at each site.This paper presents the current tailings governance process at BHP, and the initiatives that were undertook towards achieving a zero failure goal. CITATION:Alexieva, T, 2018. Tailings governance, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 2–7 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Sufficient time has elapsed since the enactment of the amendments to the mining legislation in 1981 to enable an examination to be made of the way in which the licensing system operates in practice. One of the most important decisions in resource management in New Zealand is whether or not rights of access to the resource should be conferred by the Crown upon an appropriate private sector participant. The licensing system is the means for allocating these rights of access. The manner in which the licensing system is administered, therefore, is crucial to natural resource management in New Zealand. What is the mining licensing system in New Zealand designed to achieve? This simple question admits of no easy answer. Is it the identification and development of the mineral resources of New Zealand? Are these objectives tempered by issues of resource conservation and environmental protection? Is a balance to be achieved among these competing factors? Does the legislation contain any priorities? Does the system respond in an ad hoc manner to particular facts and circumstances or does it operate within a more predictable framework? To what extent are decisions made on access to minerals with reference to the development or conservation of other resources? These questions may be summarised in the title to this paper which poses the question whether mining licences are instruments for resource management.

Jan 1, 1988

By W Kendall

Ore sorting has the potential to reduce the feed to wet plants and in the case of complex orebodies that can significantly reduce the water, energy and reagent consumptions and resulting operating costs for the project. The application of ore sorters has sparked renewed interest and application in the precious and base metals mining industry in recent years as a result of the continuing development of new sensing technology and very fast information processing that is making ore sorters applicable to a much wider range of ores and larger scale operations. The application of ore sorters involves a range of trade-off decisions that have economic impact upon the benefits of ores sorting to the project under consideration. This paper will present some typical trade offs to be considered and their impact in a particular project setting. CITATION: Kendall, W, 2018. How economics drive the application of ore sorting, in Proceedings Complex Orebodies Conference 2018, pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A D. Campbell, G R. Power

The objective of the draw strategy in a caving mine is to maximise economic return by minimising waste dilution3 and maximising ore recovery4. The draw strategy must also include suitable controls for air blast and mud rush hazards and is highly constrained until continuous cave propagation has been achieved. This paper details a three-year project at the Ernest Henry Mine (EHM), which used cave flow simulation software to develop a draw strategy that increased the mine value by 32 per cent.Dilution and ore loss can be significant in sublevel cave (SLC) operations and result in poor recovery and considerable economic losses. To minimise dilution and ore loss, cellular automata software was used to simulate cave flow over the mine life. The optimisation project required mining footprints for various cut-off grades to be developed. Draw strategies for each mine footprint were then generated using a range of shut-off grades. Economic assessment of each scenario was then conducted to determine the mine footprint and corresponding draw strategy that generated the highest NPV (net present value). The iterative simulation process was improved by developing automated software functions in the flow modelling software to reduce time taken to generate and assess life-of-mine (LOM) draw strategy scenarios.In addition to improving the NPV of the mine, the optimisation project also enabled a decrease in the mine cut-off grade which increased the ore reserve and extended the mine life. Overall, an iterative process of mine planning, cave simulation, economic evaluation and geotechnical analysis was used to significantly increase the economic return of the SLC whilst ensuring caving risks were controlled to an acceptable level.CITATION:Campbell, A D and Power, G R, 2016. Increasing net present value by a third at an operating sublevel cave mine using draw strategy optimisation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 167–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

By J M. Galvin, B J. McKinnon

Lightning Ridge, Australia, is the largest opal producing area in the world. Most opal is mined from shallow underground mines by individuals or small partnerships with the industry having been protected from large-scale development to date. The safety performance of opal mining has lagged both general mining industry standards and community expectations. The application of geotechnical analysis to the opal fields has the potential to considerably reduce injuries and fatalities. With consideration of the local culture, preliminary geotechnical analysis has been applied to some current methods of work utilised at Lightning Ridge. Practical solutions have been advocated and are presented in this paper. Improvements to safety generated by these practical solutions indicate that further geotechnical research at Lightning Ridge is warranted and would be beneficial.

Jan 1, 2002

By A R. Hollis, M Heddon

The safe life cycle of a Tailings Storage Facility (TSF) is founded on the fundamentals of proper design, construction, operation and closure. Leinster Nickel Operations (Leinster) utilises four active TSF cells that are cycled between filling (deposition), desiccation, and construction to meet a targeted rate of rise. This results in ongoing and consistent raising of the TSF walls. Critical to maintaining the safe life cycle through this consistent wall raising is precision construction and high frequency quality assurance to ensure compliance to design requirements and TSF walls free from defects. Leinster has recently deployed Intelligent Machine Control technology for TSF construction. Advances in Intelligent Machine Control have decreased variability in construction; ensuring variations are within the tolerances of design. The Intelligent Machine Controls are programed to ensure construction conforms to design tolerances of +/-30mm. This level of accuracy provides assurance of borrow area set out, compacted layers are as per design, compaction monitoring is within the zone placed, scarification between layers to prevent lamination is maintained, and batter angles are set to the correct grade. This level of control provides certainty that construction meets the design intent. In conjunction with Intelligent Machine Control, periodic drone surveys are conducted to verify construction against design. Advancement in survey equipment and techniques allow higher frequency, high accuracy survey to be completed on demand by site based personnel. This provides quality assurance through all stages of the construction phases, as well as the final constructed wall, ensuring compliance to design. Combining Intelligent Machine Control with higher frequency quality assurance provides an increased level of certainty that the TSF construction is defect free and within quality specifications. These recent technological advancements in Construction and Quality Assurance ensure cell raises are constructed to the design intent with greater levels of accuracy and precision than ever before.

Jul 1, 2021

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

A modified liquation technique was developed for recovering tin from tinhouse scruff metal or hardhead containing about 10 per cent iron and 15 per cent occluded flux, palm oil, and moisture. This was effectedby heating the scruff metal to 950°C followed by rapid cooling to suppress the formation of FeSn2 and FeSn, and then subjecting it to the ordinary liquation and drossing processes of refining. By this method it was possible to recover about 83 per cent of the original tin content and, with subsequent smelting of the irony drosses, an overall recovery of 92 per cent was obtained.

Jan 1, 1969

By R Dimitrakopoulos, R Goodfellow

One of the primary objectives when optimising a mining complex is to maximise its value for the primary stakeholders. In order to achieve this objective, it is necessary to holistically optimise all aspects of the mining complex, including decisions of when to extract materials from the available sources, how to blend or stockpile these materials and how to best use the available processing streams to satisfy customer demand. Existing methods for global, or holistic, optimisation ignore the compounded effects that risk has on the performance of a mining complex. Over the past decade, several stochastic optimisation approaches have been proposed to integrate various forms of uncertainty into the open pit mine design and production scheduling. These methods, however, are limited in their ability to simultaneously optimise the production schedules for the portfolio of mines, material destination policies, the use of the available processing streams and the various products that are produced at each location of the mining complex.This paper aims to discuss a new method for the global optimisation of open pit mining complexes with geological uncertainty. The proposed generalised methodology is capable of modelling and holistically optimising mining complexes, including aspects related to production scheduling, blending, stockpiling and non-linear interactions that often occur in practice, but are over-simplified in existing models. Two case studies are discussed to highlight the need for these complex, stochastic optimisers. First, a case study for a nickel laterite blending operation highlights the need to integrate geological uncertainty into the optimisation in order to ensure product quality constraints are respected. Second, a case study for a copper-gold mining complex highlights the added value when simultaneously optimising the production schedule and the stockpiling and treatment of extracted materials.CITATION:Goodfellow, R and Dimitrakopoulos, R, 2014. Stochastic optimisation of mineral value chains – developments and applications for the global optimisation of mining complexes with uncertainty, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 13–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The Kiirunavaara apatite-magnetite orebody is about 4 km long and approximately 100 m thick sheet-like body, which lies roughly in a north-south direction and dips from the horizontal plane along its entire length, in towards the town of Kiruna. The origin of this orebody has been a matter of controversy, with both magmatic and hydrothermal origins proposed. Traditionally and for practical purposes this rich apatite-magnetite ore has been divided into two main types: low phosphorous ore (B-ore) and high phosphorous ore (D-ore). Further the low phosphorous ore is divided into the low alkali (B1) and the high alkali (B2) ore.

Jan 1, 2006

By P A. Montoya

La Colosa is a world-class porphyry Au project located in Colombia, currently undergoing prefeasibility analysis. As part of collaboration between AngloGold Ashanti and the AMIRA P843A GeMIII Project, the application of emerging geometallurgical characterisation testing and modelling tools has been incorporated in early stages of project development. The aim of the geometallurgical study is to map inherent comminution variability across the La Colosa deposit providing information critical for mine/mill design and optimisation. In this study, site-based data incorporating multi-element assays, quantitative analyse X-ray difraction QXRD bulk mineralogy measurements, EQUOtip rebound hardness data, and routine geological logging information from 59 diamond drill holes has been integrated with a range of geometallurgically specific comminution test (ie GeMCi, A × b, BMWi). The work in this paper demonstrates the integration techniques used at La Colosa to link routine data acquisition methods with comminution test results through the development of proxy support models. The integration incorporates a range of statistical techniques including principal component analysis and regression modelling. By creating proxy models, comminution index estimates can be propagated into the geological database enabling comminution processing domains to be defined. These domains provide the first spatial representation of comminution performance and variability at La Colosa and can be compared against traditional geological domains. This study provides the foundation for ongoing comminution characterisation as the La Colosa project evolves through project cycles into an operational mine.

Sep 5, 2011

By Davies S. G, Jayaweera A

The oxidation of nickel sulphide and copper sulphide concentrates, and coal, has been studied under non-ignition and ignition conditions using Differential Thermal Analysis (DTA) and Thermogravimetry (TG). The non-ignition reaction was favoured by slow heating rates < 10°C min-1), low masses < 10 mg) and an air atmosphere. Under these conditions, the typical stepwise oxidations of the various sulphide minerals present in the concentrate were observed as resolved exothermic peaks in the DTA curves and weight losses in the TG curves. Above a heating rate of 10°C min-1 , sample masses in excess of 10 mg and an oxygen atmosphere, an ignition reaction was induced, as indicated by a major high energy exotherm in the DTA curve and a major rapid weight loss in the TG curve. The ignition temperatures of the minerals under ignition conditions, found for 15 mg samples heated at 20°C min-1, were 434°C for the nickel sulphide concentrate, 372°C for the copper sulphide concentrate, and 230°C for the coal. By plotting a curve for mass against ignition temperature at constant heating rate and extrapolationto zero mass, a value of 470°C was obtained for the mass independent ignition temperature of the nickel sulphide concentrate. Ignition temperatures and extents of reaction at various temperatures were obtained using the TG technique in a novel manner which produced heating rates of 4500°C min-1. Under ignition conditions, the oxidations approximate to flash smelting conditions.

Jan 1, 1985

By M Jara, R Nuñez

As the global interest in sustainable energy sources has increased, lithium has emerged as a vital resource, playing a crucial role in the transition towards a cleaner and more efficient economy, but with this comes important challenges, especially associated to health, safety, and environmental matters. So, it is imperative for the lithium industry to prioritise HSE measures to protect workers, environment and surrounding communities. Implementing robust safety protocols and technology helps ensure the sustainability of mining operations and contributes to the overall responsible development of the industry. In this work we present how the Chilean lithium mining industry becomes a safer and more compliant industry using digital transformation (Cochilco, 2018; Bradley et al, 2013; Cabello, 2022).

Apr 16, 2024