Search Documents

The C.S.I.R.O. acid alumina process employs the essential steps of digestion, hydrolysis and calcination to produce pure alumina from ores too high in silica or too low in grade for the Bayer process. The two latter stages have been described in some detail previously but the digestion stage requires separate discussion since ores vary widely in composition and reactivity. Kaolinitic clays require roasting to 800°C to render the alumina soluble in the 11 per cent sulphuric acid used in the process while some ferruginous laterites require roasting to reduce the reactivity of iron minerals.The iron content of pregnant solutions is kept at a low figure by digesting at temperatures where the solubilities of ferric oxide or basic ferric sulphates are small. A two-stage, counter-current digestion is necessary to extract a high percentage of alumina from the ores and to produce a basic pregnant liquor with an SO3 : AI 203 ratio of 1'\1 suitable for high temperature hydrolysis. The second stage of digestion, called the modification stage, treats slightly acid liquors with excess of ore in the temperature range 1200-1400C.The first stage operates at 170°-1900C to extract further alumina from modification residues, using recycled acid obtained from later steps of the process. Both temperature ranges are critical for economic operation and for proper control of the iron content of solutions. In batch experiments, 30 min is regarded as a suitable retention time for digestion and modification; ores which require much longer than this are less suitable for the process. Impurities such as silica, and titanium and vanadium oxides are discarded in the residue along with iron oxide, and do not contaminate the final product. Bivalent metallic sulphates such as MgSO4, can build up in the circuit to a very considerable degree without affecting product purity.Comparison with other processes shows that the C.S.I.R.O. process is superior for control of contamination by iron, which is the major problem in acid processes. The pure intermediate product (3Al203.4S03.9H20) is also more convenient for calcination to alumina than the hydrated aluminium sulphate usually recovered in other processes. Detailed cost comparisons must await pilot-plant evaluation of the C.S.LR.O process.

Jan 1, 1964

This investigation was planned to determine:1. The precipitation-hardening properties of the copper-nickel-phosphorus alloys; and2. The influence of arsenic and bismuth, singly and together, on the mechanical properties of these alloys.It was carried out in conjunction with an investigation, previously published in these Prooeedings on "The Influence of Various Elements on the Mechanical Properties of Copper containing a small percentage of Bismuth," and also formed part of a study of the influence of bismuth, nickel and phosphorus on the properties of commercial arsenical-copper.The first part of the present investigation arose out of a discovery some years ago of precipitation-hardening in phosphorus-deoxidized coppernickel boiler tubes, containing approximately 2% nickel and 0·03% phosphorus, supplied to an Australian Railways Department. At that time there was little information available on precipitation-hardening in copperrich copper-nickel-phosphorus alloys, but at the end of 1935 a short paper on the subject was published by E. C. Rollason and T. G. Bamford(2) and at the beginning of 1940 a comprehensive account was published by D. K. Crampton, H. L. Burghoff and J. T. Stacy.(3) Although the investigation carried, out independently by the present author was not as comprehensive as that of Crampton, Burghoff and Stacy, the results are in agreement with those of the American as well as of the British authors; hence, only a summary of this aspect of the work is needed here to establish a basis for a study of the influence of bismuth and arsenic.PREPARATION OF TEST PIECESAll alloys were melted under charcoal in plumbago crucibles in an oil-fired furnace and were poured out of contact with air into oil-dressed moulds to give billets either 7· 5 in. long X 0.83 in. diam. X 1·3 lb. weight or 12 in. long X 1·125 in. diam. X 3·3 lb. weight depending on requirements (the larger size was used, for example, in establishing the annealing characteristics of the precipitation-hardening alloys). The raw materials were electrolytic copper of the composition described in the previous paper(I) 6% copper-arsenic, 14% copper-phosphorus, 1:7% copper-bismuth, and Mond nickel in the form of "shot." The method of producing test pieces from these billets and the annealing treatments ana tests to which the pieces were subjected have been described in the previous paper.

Jan 1, 1944

By S Hapugoda, M Kilburn, M Adam, L Lu

Lump ore is one of the key ferrous materials used in the blast furnace ironmaking process, typically accounting for 5–25 per cent of the blast furnace ferrous burden. Like other ferrous materials, the characteristics of lump ore have an important impact on stable operation and productivity of a blast furnace. As the cold burden lands on the top of the hot burden in the furnace and descends, it is inevitably subjected to thermal shock, which will likely lead to breakdown of the lump particles, or decrepitation and affect the gas permeability inside the blast furnace adversely. An ISO decrepitation test has therefore been developed to assess this behaviour of lump ore. However, the results obtained according to the existing standard decrepitation test method vary considerably between laboratories even for the same lump ore. To improve the test procedure of the existing decrepitation test, this paper first discusses the mechanisms leading to decrepitation and then studies the factors affecting lump ore decrepitation. Understanding the key factors affecting lump ore decrepitation is particularly important to improve the existing test procedure that enables researchers to achieve a higher degree of precision when conducting the decrepitation test.CITATION:Lu, L, Adam, M, Hapugoda, S and Kilburn. M, 2017. Decrepitation of lump iron ores, in Proceedings Iron Ore 2017, pp 91–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By F Farías, D Villa

Codelco’s Salvador Project has been operating a block/panel caving mine for more than 50 years. This underground mining method dynamically mixes the ore and dilution. As a result, forecasting grades is difficult and achieving 100 per cent extraction of the reserves is practically impossible. A substantial volume of the ore mixed with dilution becomes remnant ore and remains to be subsequently extracted.A potential open pit mine is under evaluation at Codelco’s Salvador Project, which includes the extraction of remnant ore post-block caving extraction. An effective methodology has been implemented to estimate what is left behind once the underground mine has closed. A new mixing method using the Cellular Automata (Alfaro and Saavedra, 2004) approach has been used to allow estimation of the remnant ore with a sufficient level of confidence to be included as part of the open pit reserve.A remnant block model is created using elements such as in situ block model, drawpoint layouts, historical production records and the drawpoint extraction. Using this information, simulations of the extraction of the mine by month from 1959 to 2019 were completed, using different mixing scenarios and trying to replicate the tonnage and grade extracted.Finally, the remnant block model is categorised using a score card with four inputs to assess the risk of the estimation of this material into a category class (measured, indicated and inferred).CITATION:Villa, D and Farías, F, 2016. Remnant ore model generation and categorisation post-block caving extraction at Salvador Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 461–470 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J Theiler, B Beamish

The presence of reactive metal sulfide minerals in waste rock contributes to the hazard of spontaneous combustion in dumps, as these minerals react with air and water entering the dump at ambient temperatures to form various mineral products and significant heat. This reaction series can also be an initiator of self-heating of carbonaceous material present in the waste rocks if sufficiently high temperatures are reached. Characterisation of these reactive minerals has primarily been to assess the risk of acid mine drainage, which is not necessarily an indicator of spontaneous combustion risk. No systematic testing procedure has been adopted by industry to assess the spontaneous combustion propensity of the waste rock. As a consequence, the principal management strategy for spontaneous combustion has been a reactive approach of dealing with events as they arise.Recent advances in adiabatic oven-testing have enabled more definitive assessment of the spontaneous combustion propensity of coals, including the quantification of the accelerating influence of reactive pyrite (Beamish and Beamish, 2011, 2012; Beamish, Lin and Beamish, 2012). This same test procedure has been used to assess the self-heating performance of metal concentrates and is therefore amenable to assessing the metal sulfide oxidation process from low ambient temperatures. The data obtained from such testing can be used to quantify the more prone waste rock sequences of a mineral deposit in advance of mining. This enables appropriate management planning for emplacement and long-term storage of waste rock in dumps.CITATION:Beamish, B and Theiler, J, 2016. Characterising the spontaneous combustion propensity of waste rock, in Proceedings Life-of-Mine 2016 Conference , pp 93–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

How the Australasian and Canadian Codes (VALMIN and CIMVal) approach mineral property valuation is described. Brief comment is also made on the International Valuation Standards CommitteeÆs interest in a global valuation standard for Mineral (Extractive) Industries and the South African SAMREC initiatives to adopt a VALMIN-like Code. The conventional tripartite classification of valuation approaches into those that are Market-based, Income-based and Cost-based is outlined. It is best practice to use as many of these approaches as possible (and as many methods as reasonable in the particular circumstances), given the quantity and quality of the data available on the Mineral Asset (which depends upon the state of development of the mineral property). The use of specific methods must satisfy the basic considerations of logic and reasonableness and the purpose of the valuation. The competence, judgement and repute of the valuer are critical factors, since all valuations are time and circumstance specific. What constitutes æMarket ValueÆ in the different jurisdictions is discussed and definitions are given. Challenges facing the globalisation of a VALMIN-type Code for the international Minerals Industry are the influence of real estate valuers and the US jurisdictional idiosyncrasies. This is mainly due to a fixation on real property rights with a preference for using real estate-like comparative sales techniques (Market Approach) to the exclusion of Income-based approaches; a regulatory reluctance in the US to accept that Resources have considerable value; and the International Accounting Standards BoardÆs preference for Historical, rather than Current Value, accounting.

Jan 1, 2002

By Parker A. J, Ruane M, Wadley L. G B

Copper, sulphur, nickel, cobalt, palladium, silver, and gold can be recovered from the copper sulphide precipitated from the "copper boil" of the Sherritt-Gordon nickel process used at Western Mining Corporation's Kwinana nickel <refinery. The method is based on an oxidative ammonia leach of copper, nickel, and the precious metals at temperatures below 40°C to produce, in part, elemental sulphur, in the residue. This is followed by heating to decompose thiosulphate and remove some ammonia with precipitation of some of the copper, palladium, gold, and silver. Addition of sulphur dioxide to pregnant liquor precipitates copper, as either Chevreul's salt or copper(I) ammonium sulphite, together with the remaining gold and silver. Less than 10 per cent of the dissolved palladium and less than 1 per cent of nickel and cobalt precipitate to this stage.In one option, the Chevreul's salt is dissolved in a solution of copper(II) sulphate, acetonitrile, and water to generate a solution of copper(I) sulphate. Gold and silver do not dissolve. The solution of copper(I) sulphate is thermally disproportionated by distilling acetonitrile to give exceptionally pure copper powder, with desirable characteristics for powder metallUrgy. Nickel, cobalt, and ammonium sulphate are recovered from the motherliquor of the Chevreul's salt precipitation by return to the Sherritt-Gordon process, where recovery procedures already exist. Palladium is recycled for eventual removal as a sulphide with the gold and silver.In the other option, solid copper(I) ammonium-sulphite is <thermally disproportionated in water at 150°C to copper powder.

Jan 1, 1978

New Zealand has been a significant producer of gold for over a century. Total recorded production is over 850 tonnes. There were three major periods of production: the first and biggest was between 1860 and 1880, the second was between 1895 and 1920 and the third was between 1930 and 1945. After 1945 gold production fell continually until 1980 when the major upward adjustment in gold price led to renewed interest. There have been important new developments in each of the known gold-rich areas: Westland, Otago and Coromandel and exploration for gold in these areas and in previously unprospected regions has reached unprecedented levels.

Jan 1, 1988

Ridgeway Gold Mine (Ridgeway) has a clear mission to maximise its cash flows in order to deliver shareholder value and is developing strategies to achieve this. Business process management using leading measures is core to this approach. Leading measures indicate potential outcomes ahead of time, allowing time to adapt and improve. Ridgeway is making strategy a central organisational agenda, creating a focus to æput first things firstÆ by controlling æleadingÆ activities and mobilising employees to act. Feedback using specific, leading measures gives employees the opportunity to proactively adapt their behaviour in order to deliver internal business outcomes that generate cash flows and shareholder value. This paper will outline RidgewayÆs business approach to track and control processes from resource to revenue, with a focus on delivering cash flows and shareholder value. Ridgeway is implementing a Balanced Scorecard approach (Kaplan and Norton, 1996). A total business focus is taken and leading measures are identified. Specific measures are used to score our success from the perspectives of learning and growth, internal business processes, customer and stakeholders, and finance. These measures and improvement plans are targeted at strategies to maintain our ælicence to operateÆ with our community stakeholders, produce accurate plans and forecasts, improve our operational effectiveness and grow our business.

Jan 1, 2002

By Zharinov SE

Geonechanical modelling of island arc sys- tems and their analogs is investigated. Slow seismotectonic movements along the inclined deep fault zone under the compressive horizontal stress conditions are proposed to be the princi- pal mechanism controlling the structures and processes in the active continental margins. A model of shearing surface crack in an elastic half-plane is used for simulation. The main ele- ment of the model is viscous interaction bet- ween the crack sides, the viscosity varying with depth. To describe the stress-strain state of the medium an integro-differential singular equation is derived and solved numerically. The results of simulation are in good agreement with geological and geophysical data on the ac- tive continental margins.

Jan 1, 1987

By Garnsey R. G T, Wenk G. J, Toop A, Sowerby B. D

A bulk mineral analyser (BMA) suitable for the determination of Cu or Ni in bulk ore samples has been developed at the Lucas Heights Research Laboratories. This analyser, which uses the nuclear resonance scattering technique, is highly specific to the wanted element. The technique has previously been extensively field tested for copper at Mount Isa, Queensland.The present paper discusses the field trial in 1982 of a commercial prototype BMA for nickel. The trial was undertaken at the lateritic nickel mine at Greenvale, Queensland. The BMA and its shielding, together with a laboratory spectrum analyser, were sited in the sample shed adjacent to the workings. Two hundred and thirty-eight ore samples taken directly from the mine blastholes were assayed by the BMA. The average mass of sample was 12 kg, metal contents varied from 0.2 to 3.5 wt/per cent Ni and 4 to 43 wt/per cent Fe and free moisture varied from 11 to 55 wt/per cent. A measurement took 10 min to complete, although this time could have been reduced at the higher nickel grades. The r.m.s. deviation between BMA and chemical assays was 0.09 wt/per cent nickel. Iron and bulk density were also determined by the BMA, r.m.s. deviations being 1.7 wt/per cent and 0.03 g/cmJ respectively. Similar results could be expected from a BMA in routine industrial use at other nickel mines.

Jan 1, 1983

By D Pilone

The Tyrrhenian micro-nodules, findable at low depths (200/600 m under s l) are a reasonable reserve of manganese. They can be easily and cheaply recovered but do not contain valuable metals as in the case of oceanic nodules. In this work a hydrometallurgical process for manganese recovery from Tyrrhenian nodules is presented. The studied treatment includes the following operations: magnetic enrichment, reducing leaching, leach liquor purification and electrowinning . The study shows that the most important step in the process is the preliminary manganese enrichment. It can be done directly on the platform reducing not only the transport cost, but also the residue mud in the metallurgical plant. The leaching parameters such as status and size of nodules, temperature, composition of leaching solution and S/L ratio have been investigated. After purifying the leach liquor by iron precipitation as ammonium jarosite , the conditions to electrowin manganese have been investigated. The yields of both manganese leaching and iron precipitation together with current efficiency and specific energy consumption in the electrowinning step are given.

Jan 1, 2000

By J Watt

The Hidden Valley Gold Project is located in a remote and mountainous area of the Morobe Province approximately 30 km south of the township of Bulolo and approximately 90 km south-southwest of the provincial capital, Lae. The Hidden Valley deposit was discovered in 1984 with the nearby Hamata and Kaveroi deposits discovered in 1987 and 1992 respectively. Reserves (Harmony, 2009) at these three deposits are 42.1 million tonnes of ore containing approximately 2.9 million ounces of gold and 45 million ounces of silver. A further 5.4 million ounces of gold and 84 million ounces of silver are in the resources category. The process plant is designed to treat 4.2 million tonnes per year of gold/silver ore extracted by open cut mining methods. Ore is classified into three ore types according to oxidation state: oxide, transition and primary. The silver to gold grade ratio is high for the Hidden Valley and Kaveroi ores, generally in the range 15 - 20:1, and much lower for Hamata, typically 1 - 2:1: Primary ore is the dominant ore type at Hidden Valley with sulfur grades up to about two per cent sulfur. Oxide and transition ores are more prevalent at the Hamata deposit, but its primary ore has up to five per cent sulfur grades. Variable ore types, particularly in the initial years of operation, high silver to gold ratios and limited plant site area, due to the challenging terrain, present the main processing challenges for this project. This paper describes the operating strategies and process development for the main areas of this circuit, highlighting selections of processes and equipment that achieve cost effective, yet flexible solutions to the treatment of ores from these deposits.

Jan 1, 2009

By A G. Thompson, E Villaescusa, A De Zoysa, J R Player

Ground support performance is critical to the safe and economical extraction of ore. This is particularly important for mass mining extractions at great depth, which are currently being considered by a large number of mining companies worldwide. As the in situ stresses concentrate around critical excavations, failure occurs at the excavation boundaries and ground support is required for the excavations to remain safe and accessible for their intended lifespan. Ground support consists of reinforcing elements that are installed within the rock mass to modify its internal behaviour (generally to within one excavation radius) and surface support elements that are installed at the exposed boundaries to retain the failed pieces of rock. For surface support to be effective, the loadings need to be transferred to the reinforcing elements; however, the combined performance of rock bolts and mesh is poorly understood in terms of the energy dissipation capacity available for a typical ground support scheme implemented at most mass mining operations.Over the last 15 years or so, a large number of large-scale laboratory experiments have been completed at the Western Australian School of Mines (WASM) Dynamic Test Facility for reinforcement systems and surface support systems loaded separately. The objective of more recent testing has been to establish the combined energy dissipation capacity of typical and enhanced reinforcement systems combined with mesh surface support. Total energy dissipation has been separated into energy dissipation attributable to the reinforcement and to the mesh. The results of the tests are presented and compared with the existing WASM design demand and capacity guidelines.CITATION:Villaescusa, E, De Zoysa, A, Player, J R and Thompson, A G, 2016. Dynamic testing of combined rock bolt and mesh schemes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 789–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

This paper describes the excavation of No. 1 Power Station Lift Shaft at the Kiewa Hydro-Electric Project. The advantages and limitations of the borehole method are outlined, and general principles of plant design are discussed.INTRODUCTIONFor many years, attempts have been made to reduce mine development costs by various methods. Some of the, techniques of tunnelling have been adopted in horizontal headings, and in main vertical shafts, mechanical plant has displaced hand labour with notable success. However, in the field of small rises and winzes, improvements have largely been effected by attention to details of procedure. The most promising avenues for' substantial reductions in cost relate to:(a) Long-hole drilling(b) The borehole method(c) Calyx drilling.Whilst each of these methods has its peculiar advantages, the borehole rising method is probably most useful, and capable of wide application.In brief, the borehole method of rising requires a, drill hole parallel to the axis of the rise. A hoisting rope is passed through the borehole, and is attached to a platform on which the rising crew are raised with their equipment to the drilling position in the rise.When properly planned, the method is particularly safe, and has generally received the approval of mine inspectors and safety authorities. Rising work is generally hazardous, even when special timbering methods are used. In...

Jan 1, 1959

By L Lachance, F Flament, D Leroux, S GariTpy

"Considerable metal values are often locked in stockpiles (ore, concentrates, heap leach pads, slags, reverts, etc.) and process equipment (bins, holding tanks, thickeners, etc.). This is more than enough to justify accurate accounting of such in-process metal inventories from both financial accounting and operational perspective. However, accurately determining the metal inventory of an in-process unit is often a challenge in industrial practice. Audits have shown that available indirect or direct measurements often carry large inaccuracies. Sooner or later, ignoring these measurement errors lead to unexpected incoherencies in reported metal balances. In such situations, coherent metal balances are then achieved through subjective and sometimes significant adjustments of in-process inventory levels. While such metal accounting methods applied by mineral processing engineers used to be rarely challenged, they are now being increasingly scrutinised by various stakeholders. Hence, metal accounting procedures that mitigate subjectivity in adjustments while still coping with the unavoidable uncertainty are more relevant than ever.This paper reviews three different metal accounting methods for reporting in-process metal inventory values. Their individual application strongly depends on the available measurements i.e. The indirect method where the metal inventory of a given process unit is determined by subtracting the cumulative reclaim from the cumulative feed carries important flaws. The direct method also comes with challenging accuracy issues so that emptying a process unit is often the best available inventory measurement. This reality is recognised for by further analysing a previously proposed operating mode where two interchangeable process units are alternately used. The third investigated method is the redundant method which combines indirect and direct methods for a given process unit. This paper reveals that the dual process unit operating mode and the redundant method can both significantly improve the estimation quality of in-process metal inventories.CITATION:Lachance, L, GariTpy, S, Leroux, D and Flament, F, 2013. Review of metal accounting methods for in-process metal inventories, in Proceedings MetPlant 2013, pp 102-117 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By N Collins, A Woodley, A N. Danoucaras, C McCombe, N C. Kunz

Over the past decade, the mining industry has come to recognise the importance of water both to itself and to others. Water accounting is a formalisation of this importance that quantifies and communicates how water is used by individual sites and the industry as a whole. While there are a number of different accounting frameworks that could be used within the industry, the Minerals Council of AustraliaÆs (MCA) water accounting framework (WAF) is an industry-led approach that provides a consistent representation of mine site water interactions regardless of their operational, social or environmental context that allows for valid comparisons between sites and companies.The WAF contains definitions of off-site water sources and destinations and on-site water use, a methodology for applying the definitions, and a set of metrics to measure site performance. The WAF is comprised of two models: the input-output model, which represents the interactions between sites and their surrounding community, and the operational model, which represents on-site water interactions.Members of the MCA have recently adopted the WAFÆs input-output model to report on their external water interactions in their Australian operations, with some adopting it on a global basis. To support this adoption, there is a need for companies to better understand how to implement the WAF in their own operations. Developing a water account is non-trivial, particularly for sites unfamiliar with the WAF or for sites with the need to represent unusual features. This work describes how to build a water account for a given site using the input-output model, with an emphasis on how to represent challenging situations.CITATION:Woodley, A, Danoucaras, A N, McCombe, C, Kunz, N C and Collins, N, 2013. A robust methodological approach for mine site water accounting, in Proceedings Water in Mining 2013 , pp 335-342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Real-Time Integration of Mining and Metallurgical Information for Efficient Use of Energy and Water

Sep 13, 2010

By J P. van Dijk, M Munro

Discrete vein modelling presents an innovative geology driven 3D modelling method for quantification of vein hosted mineral deposits, with far reaching potential for critical mineral supply and low impact resource extraction. By integrating key geological drivers with advanced discrete fracture network modelling, the DMX protocol (launched in 2019) converges to a more realistic representation of complex vein systems in three-dimensional space. The approach insights greater geologic reasoning in distributing mineral grades where vein boundaries are already defined. This presents a viable alternative to existing modelling and estimation methods and has important implications for mineral resource estimation and reporting. Further implications are discussed, where the enhanced understanding of complex orebody characteristics can potentially be used in optimising mining and mineral processing, supporting more sustainable and efficient mining practices.

Sep 1, 2024

By D Reid, A Fourie

The in-pipe treatment of slurries with polymer addition shortly prior to deposition is a noteworthy emerging technology of increasing popularity. Although polymer treatment has been shown to substantially modify and improve depositional and dewatering behaviour in a significant number of cases, the impacts of polymer treatment on geotechnical performance of tailings are less well understood. For example, certain combinations of polymer and slurry type have been shown to result in lower final densities at a given vertical effective stress. Despite these lower densities, polymer-treated tailings often exhibit peak undrained shear strengths consistent with untreated material. However, the sensitivity and/or brittleness of the material may be negatively influenced by the looser state created. Although these changes have been studied, most testing available in the literature was undertaken on relatively ‘fresh’ samples of polymer-treated material. However, significant shear may occur following treatment and prior to the commencement of settling and self-weight consolidation as the material moves down the beach.To study the effects of shearing on the subsequent performance of polymer-treated tailings, a test program consisting of consolidation, triaxial and direct simple shear tests was undertaken on presheared polymer-treated material. Materials used were identical to those used in previously published studies on the impacts of polymer treatment in a ‘fresh’ condition. Shearing of the polymer-treated material generally appeared to lessen the impacts of the polymer treatment process. However, the behaviour of the material when sheared indicated that the polymer was still impacting the behaviour of the material in some respects. The results indicate the importance of the consideration of shearing on material behaviour when planning and designing a tailings deposit where polymer treatment is to be implemented.CITATION:Reid, D and Fourie, A, 2015. Effects of shear on the behaviour of polymer-treated slurries, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 215–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015