Search Documents

By D M. Aranha, M A. Fonseca, M Echtern

The regional syndeformational metamorphism affecting the Itabira Iron Formation (IIF) at Quadrilßtero Ferrffero (QF) was formerly discussed by Dorr (1965), who proposed that quartz grain size could monitor the metamorphism, according to James (1955), and that the formation of haematite could be the result of the synchronous metasomatic process. Herz (1979) suggested the existence of three metamorphic zones, not mentioning the haematite formation. It could be observed that the primary oxide phase in the IIF is magnetite and most of the hard haematite was derived from the metamorphic replacement of magnetite, forming micaceous or schistose haematite. Differently from most iron formations in the world, the formation of haematite deposits at QF occurred under high oxygen fugacity during metamorphism. The haematite microlaths display a strong preferred orientation, which determines the alongated shapes of the fragments. The terms foliated and unfoliated haematite have been applied by Dorr to the micaceous or schistose haematite, and to the isotropic, hydrothermally derived haematite. Under the microcope, the haematite exhibits a strong crystallographic or lattice orientation encircling the magnetite and martite porphyroclasts. The strain rate determined and defined the textural variation, size and economic importance of the deposits and the ore grade. Metamorphism at QF increases eastward and resulted in the formation of a gruneritic Fe-Mg amphibole, at the western portion, followed by a cummingtonitic amphibole at the central-western part, succeeded by the actinolite zone at the central-eastern part, and finally to the tremolite-anthophyllite zone to the east. These zones, arranged in a north-south pattern, can be followed in the pelitic units, whereas appear sericite-chlorite, kyanite-chloritoid and garnet-staurolite respectively. Carbonate geothermometry in IIF also may support the metamorphic variations. At the western zone the haematite forms small lenses within the itabirite, P-contents are slightly higher than in the remaining IIF, haematite grain size is minute, resulting in a submicaceous texture and the amount and dimension of relict magnetite within haematite is greater than in the other parts of QF. Jangada and Serra Azul deposits are examples of this zone. The central-western zone is characterised by significant haematite deposits, in considerable quantity and size, haematite grain size increased, in order to produce a micaceous texture, the P-contents and the amount of magnetite decreased. Pico do Itabirito, Cappo Xavier, Capitpo do Mato and Tamanduß correspond to the deposit type of this zone. At the eastern-central portion the amount of the hard haematite deposits decreases, increasing the soft haematite ore due to higher strain rates. However, it can be perceived that the relict magnetite almost disappeared and the haematite grain size became coarser than the haematite from the western zones. At the eastern zone, the haematite deposits exhibit typical schistose texture, the magnetite porphyroclasts are absent and the lowest P-grades in the haematitic iron formation. The haematite bodies characteristic from this zone are Andrade, Morro Agudo and the deposits at the Itabira District. The hydrothermally derived compact and isotropic haematite deposits, formed subsequently to the micaceous haematite bodies, were generated after deformation ceased, but under very high fluid pressure. The metamorphic reactions magnetite + quartz + H2O = grunerite + haematite and magnetite + quartz + H2O = grunerite + O2 were decisive in the formation of the metamorphic haematite deposits.

Jan 1, 2007

By R Salmimies

Choosing a ceramic capillary action filter is often favoured in processes where low energy consumption is important, such as the dewatering of iron ore. In addition, the performance of the filter medium is essential, and the possibility to regenerate the medium is an advantage compared to other types of filter media. Although low, roughly 8 - 9 w-per cent for iron ore concentrate, and even cake moisture is the primary goal of dewatering, the introduction of better filtration processes can result in significant improvements of water economy and material efficiency.As industrial beneficiation processes are often complicated in their chemistry due to impurities originating from the ore itself, from the up-stream processing equipment and from the process water used, the characterisation of the filter media after usage might provide relevant information on what actually takes place during long operating periods. The aim of this study was to obtain new information on the fouling of fi lter media in an iron ore process to enhance and develop the regeneration process of the media in the future.X-ray diffraction and scanning electron microscopy were used to characterise ceramic filter media used in the dewatering of magnetite. Principal component analysis and discriminant analysis were introduced to identify trends in the data. Two types of media blockages were found to play an important role in an acidic iron ore dewatering process: fouling by slurry particles and by in situ crystallisation of a calcium compound, of which the latter originated from the combination of process water and process chemistry.

Jul 11, 2011

By Lynch A. J

A method has been developed for the prediction of the performance of multi-stage grinding-cyclone classification circuits of any degree of complexity on any ore for a wide range of operating conditions. The method involves the simulation of the circuit on a digital computer by means of. mathematical models of the individual units. At present, to establish the characteristics of the ore and the machines in mathematical terms, it is necessary to know the performance of a simple system on the ore for one known feed rate and feed sizing analysis.Further work on the separate identification of the terms defining the characteristics of the ore and the machines may permit the method to be applied directly to the data derived from small scale tests on ores.INTRODUCTIONThe cost of preparing metalliferous ores for concentration processes by, grinding and classification frequently represents a major portion of the cost of treating such ores, and it is necessary both from an economic and a metallurgical point of view that grinding and classification circuits should be operated at their optimum efficiency. It will be realized that the processes carried out in all units in such circuits behave according to physical laws and, if a mathematical representation of the laws applying to each unit could be derived, optimization of the overall process for any given conditions of feed or product may not be difficult.The physical processes in both tumbling mills and hydraulic classifiers are extremely complex and do not appear at present to be amenable to a rigorous mathematical analysis. However, empirical mathematical models of grinding units which have been presented previously (Callcottand Lynch, 1963; Lynch and Moore, 1963) may be used to discuss the operation of the grinding units in multi-stage circuits. Another type of model, which leads to a reasonable...

Jan 1, 1965

By K M. Cook, D Clark

Fatality prevention and zero harm are key focus areas for resource companies. However, they remain an ongoing challenge for high hazard industries, including the mining sector. As one example the latest International Council on Mining and Metals (ICMM) Safety Performance Report shows that, while there is generally a declining fatality trend since the organisation commenced publishing data in 2012, there were still 33 fatalities across member companies in 2022 (ICMM, 2023b). Every fatal incident brings significant pain and suffering to the colleagues, friends and family of those involved, however the failures and causal factors leading to each incident are frequently very familiar to people working in the industry, particularly those tasked with managing risk and safety. In the words of Dame Judith Hackitt, Grenfell Tower Fire Investigator, ‘there are no new accidents – just different people making the same mistakes because they haven’t learned’ (Hackitt, 2022). The recurring themes in terms of the nature of fatal hazards and their associated causes across the mining sector show that, despite improvements evidenced by the favourable declining fatality trends over the long-term (in general and outside of catastrophic multiple fatality events), changes are required to achieve fatality elimination and the aspiration of zero harm. This extended abstract and the accompanying presentation apply a mining frame of reference to the idea that there are no new accidents, examining how this applies within the industry and why the lessons from past failures are not always well understood or applied to prevent the reoccurrence of material unwanted events. Many contemporary mining and resources organisations have extensive internal incident history data and a wide variety of information on fatality incidents is publicly available, including the annual ICMM Safety Performance Report. This extended abstract and the accompanying presentation explore how this existing data can be used effectively to learn from the past and proposes practical ideas regarding strategies for successful knowledge transfer to the workforce as a key component of preventing history repeating and improving safety performance across the industry. As noted by ICMM, ‘sharing lessons from failure is vital to improving health and safety, but it’s not enough’ (ICMM, 2023a).

Apr 16, 2024

By Both R. A, Daily B

The Patawarta Diapir, located in the northern Flinders Ranges (South Australia), has intruded into late Proterozoic Wilpena Group sedimentary rocks. The diapir contains disrupted blocks of a wide variety of rock types, most of which can be correlated with the Lower Callanna Beds of Willouran age, in a matrix of predominantly carbonate and siltstone breccia. Mafic rocks in the diapir appear to predate intrusion of the diapir. As with many other diapirs in the Flinders Ranges, copper mineralization is present in the diapir and occurs as narrow veins consisting essentially of carbonate with chalcopyrite and pyrite that formed after diapiric intrusion.Fluid inclusion studies demonstrate that the mineralizing fluid was a Na-Ca-K-Cl brine; probably derived by expulsion of interstitial water following emplacement of the diapir, with dissolution of evaporites within the Callanna Beds sediments and enrichment in copper by reaction with these sediments and associated basic igneous rocks. Mineral assemblages combined with fluid inclusion and geochemical data indicate a possible environment of vein formation of T ÿ 165°C, pH ÿ 4.3 ± 0.9 and log fO2 ÿ -47.3 ± 0.5. Sulphur isotope analyses indicate d34Sfluid ÿ 10 per mil, suggesting evaporites in the Proterozoic sediments as the major source of the sulphur but with some additional sulphur from an igneous source, possibly leached from the malic rocks of the diapir.

Jan 1, 1986

By S Jephcott

The McArthur lead-zinc-silver deposit is of the stratiform type. It consists of a mineralised bituminous shale sequence containing some tuffites, numerous graded beds and isolated slump breccia horizons. The principal sulfides; pyrite, sphalerite and galena, are essentially restricted to the shales and the genetically unrelated turbidites contain only minor mineralisation. The geochemistry of the deposit has been investigated with respect to the stratigraphic column and mineralogy of the sediments. A sedimentary origin is advocated for the deposit. Volcanism, thermal spring activity and high salinities, perhaps related to the Emu Fault, are considered as contributing factors to ore genesis. The metallurgy of this deposit is discussed in relation to its geologic history.

Jan 1, 1971

By S Thomson, M Lovitt, T Purvis, C te Kloot, T Nguyen, Z Liu

Ernest Henry Mine (EHM), located in north-western Queensland, is an underground copper/gold sublevel caving operation currently producing over 6 Mt/a of ore. The mass mining method of sublevel caving (SLC) used at EHM involves systematically blasting a series of uphole rings in parallel ore drives and drawing the broken ore using a top-down approach. Each ore drive contains multiple precharged rings to prevent having to charge in close proximity to the brow of the previously fired ring; however, the current initiation system still involves ‘hooking up’ all detonator lead cords of the first precharged ring. The unstable nature of a rill and working close to a brow presents hazards to personnel completing the hook-up process. There is also a business risk of ore loss when damaged ground support completely prevents access to the next precharged ring. If the hook-up step could be eliminated, the risk to personnel and the business would be significantly reduced.EHM engaged Orica Mining Services in 2016 to trial their WebGenTM 100 – wireless electronic blasting system (WEBSTM) for the first time in an underground mining environment. Having successfully signal-tested the equipment, two test holes were initiated, followed by a single production ring and then multiple production rings. In total, 30 production rings were successfully fired underground at EHM in 2017. To do this, WEBSTM was successfully integrated into EHM’s current charging and firing process, resulting in no business delays or loss to production. None of the 30 rings required hooking up and all were initiated from the surface with no personnel underground. A high level of ownership from all personnel involved ensured the trial was a success, and provided scope for wireless detonators to be used successfully on a large scale – both at EHM and other sublevel caving operations. WEBSTM is now a proven example of technology that can be used to improve safety in the mining industry, through eliminating the need for personnel to work in hazardous areas.CITATION:te Kloot, C, Liu, Z, Purvis, T, Thomson, S, Lovitt, M and Nguyen, T, 2017. Improving safety through technology – Orica wireless electronic blasting system trials at Ernest Henry Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 39–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Misra V. N, Cheng C. Y

Two types of Mt Tom Price hematite iron ore from Hamersley Iron P/L were tested using a Humboldt Wedag Jones P40 wet high intensity magnetic separator (WHIMS). The parameters tested were magnetic intensity (7000, 9000 and 11 000 Gauss), groove plate type (8R and 12R) and gap width (2.5 and 1.8 mm). It was found that at 9000 gauss magnetic intensity, reasonably high-grade and recovery in the concentrate were obtained. At 2.5 mm plate gap width, the 12R groove plate performed slightly better than the 8R groove plate. Further testwork is recommended to optimise the magnetic intensity, feed flowrate and pulp density, wash water pressure and flowrate with 12R and 8R groove plates at 2.5 mm gap width.

Jan 1, 1999

By K Williams, M Pender, T Honeyands, T Krull, D McCallum, R Holmes, R Orense

Bulk cargoes, including iron ore fines, must be shipped according to the rules agreed by the member states of the International Maritime Organization (IMO). One critical safety measure is the transportable moisture limit (T?ML) required for Group A cargoes (cargoes that may liquefy). A number of shipping incidents involving iron ore fines from India, where liquefaction of the cargo was suspected to be the cause, have brought the issue of iron ore fines T?ML into the spotlight. Extensive research has been undertaken by the major iron ore producers from Australia and Brazil to support the IMO in developing regulations for the shipment of iron ore fines. To this end, iron ore companies sponsored the AMIRA P1097 project to establish a modified T?ML test approach specific to iron ore fines. The project was undertaken by TUNRA Bulk Solids, CSIRO’s Centre for Bulk Solids and Particulate Technology and the University of Auckland, with project leadership provided by Creative Process Innovation. This program of work supported test work findings from the IMO Iron Ore Technical Working Group, which reported its findings in September 2013.The purpose of this paper is to present the major research findings from the AMIRA P1097 project, which includes a review of the original T?ML methods, highlights of the research that supported the new iron ore fines T?ML method and an outline of current iron ore T?ML requirements.CITATION:Williams, K, Honeyands, T, Holmes, R, Orense, R, Roberts, A, Pender, M, McCallum, D and Krull, T, 2015. Maritime bulk cargo transportable moisture limit requirements for iron ore shipments, in Proceedings Iron Ore 2015, pp 399–410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of 'overburden modification' due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and 'overburden modification' has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

Sphalerites from Devonian cassiterite-sulphide deposits and Pb-Zn-Ag fissure veins have similar ranges of Cd contents, but the average Cd and Fe contents could indicate a small initial difference in availability of Cd between the Zeehan-Renison Bell district and the Mt. Bischoff-Waratah district. Sphalerites from banded Pb-Zn deposits (Rosebery and Hercules) are characterized by low Cd content which is a world-wide feature of such deposits in exIrusive rocks, and may indicaIe a genetic relationship between ore deposition and vulcanism.

Jan 1, 1968

This paper addresses, in particular, the influence of winding depth on the selection of head ropes for Koepe winders. Because this is just one aspect of winder design that affects the operational safety of the winding system, the paper starts by considering all the issues governing the life and safety of the winding ropes. Regulations from a variety of countries are reviewed and comparisons of the legislated rope factors of safety and their variation with winding depth are made. This is followed by a discussion of the typical observed mode of in-service deterioration of Koepe head ropes. This mode of deterioration is due to fatigue and is influenced by the load range occurring in the ropes. Parameters contributing to load range are discussed and the influence of winding depth is highlighted. Lessons learned from early experience with very deep Koepe winders in South Africa are recalled. Predictions of load range as a function of depth are made, from which general rope life predictions are made for ropes selected by conventional national factor of safety requirements. This is illustrated in graphs comparing rope life as a function of depth. Typically a reducing life with depth is predicted. A rope selection strategy is advocated, which is based on achieving a constant rope life irrespective of the depth of wind. A new factor of safety (or rope design factor) equation is prepared that has the trend of increasing with depth. This proposed equation is compared with other published proposals that promote an increasing rope factor of safety with depth. It is shown that smoother winder drive controls enhance winding rope life and this improvement is quantified. The paper concludes by pointing out the consistency in predicted and observed life of winding ropes selected in accordance with legislated factor of safety approaches. It recommends the adoption of a new rope design factor equation for rope selection, to be used in conjunction with appropriate codes of practice for winding rope condition assessment and for the design, installation, operation, maintenance and testing of Koepe winders. The new rope design factor equation approaches a limiting economic depth of wind at shallower depths than the existing Koepe factor of safety approaches. However these older approaches æbuild-inÆ a reducing rope life with depth. The new rope design factor is therefore a more consistent way to select Koepe ropes and to evaluate economic trade-offs between Koepe and conventional double-drum or Blair winding systems.

Jan 1, 2005

A comparison is made between elementary block estimation techniques and the optimal methods of geostatistics using data from an Australian deposit. Considerable improvement in the estimates are obtained by using the optimal technique in this case.

Jan 1, 1975

By G Chen

Magnesite and dolomite are two salt-type minerals. The surface characteristics of these two minerals are almost the same. It is very difficult to remove dolomite from magnesite ores by flotation process. The present study was performed to develop a new collector and a better flotation scheme for magnesite from dolomite. The flotation tests show that there exists a significant difference in flotability between magnesite and dolomite when dodecyl phosphate synthesised with dodecanol, phosphorus oxychloride and other chemicals is used as collector. Sodium silicate was used as the modifier to improve flotation selectivity. It was found that sodium silicate selectively depressed magnesite at pH 4.5 - 7.5. The separation of magnesite from dolomite was achieved in a reverse flotation which resulted in a 76.1 per cent yield of magnesite with a grade of 47.3 per cent at 100 ppm dodecyl phosphate and 75 ppm sodium silicate. The flotation mechanism was investigated by characterising surface electrical properties and measuring the adsorption density of the reagents on magnesite and dolomite.

Jan 1, 2005

By F Palkovitz, S Wilson, F Felipe

The management of waste from mining operations is a significant aspect of bringing a mineral commodity to final market. The ore beneficiation process and transport/disposal of waste involves significant consumption of costly resources. A number of options exist to dispose of mill waste on surface and as a backfill material. These range in complexity, risk, capital cost, operating cost and ultimately business performance. This paper discusses the value delivered to a business in using dewatering systems including paste as opposed to conventional slurry tailings disposals. This is illustrated through various case studies and serves to demonstrate how paste can add value and reduce risk to a successful business.

Jan 1, 2009

By Taylor RN

A simple apparatus for delivering pulverized coal as fuel to a SIROSMELT lance is described, and its performance in smelting tests is evaluated. Using the pulverized coal as fuel, the SIROSMELT furnace performed well in both oxidative copper smelting and reductive smelting (zinc fuming). In both cases the evidence suggests that part of the combustion occurred by indirect oxidation of coal particles entrained in the bath. Oxygen potential measurements made during the zinc fuming tests confirmed the general features of the the non-equilibrium mechanism for zinc fuming proposed by Richards and Brimacombe. The zinc level in the slag during continuous fuming was lower than was predicted using an equilibrium model.

Jan 1, 1987

The development of Western Mining Corporation's first commercial gold heap leaching operation is described. The laboratory testwork requirements for determining the amenability of ore to heap leaching techniques is discussed. Heap construction and operating practices are described; and production statistics and operating parameters are presented. It is shown that for a specific low grade gold ore a treatment cost optimization can be performed. Taking cognizance of the ore grade, percentage gold recovery, operating costs, and the gold sale price, it can be determined whether Carbon-In-Pulp (C-I-P) or Heap Leaching should be employed as the extraction process. The examples presented in this paper refer specifically to Kambalda and should not be used in themselves as generalities.

Jan 1, 1987

By J F. H Thompson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Mineral exploration and mining are challenging businesses. Remote and at times harsh conditions have always made it difficult for exploration, but modern explorers also have to deal with cover, numerous technologies, an explosion of data and critical early community engagement. Mining deals with the reality of moving and breaking thousands of tonnes of rock each day to extract what can be a very minor component of economic value, and, furthermore, society expects that this will be done in a clean and sustainable manner. The exploration and mining challenges appear disparate, but they are intimately related.Although not widely appreciated, both exploration and mining have a long tradition of innovation. Over the last 50 years, major step changes in exploration have resulted from radical advances in our understanding of ore forming processes, new geophysical, geochemical and remote sensing technologies, and new ways to integrate and interrogate data. Over a more extended period, close to 100 years, mining has developed bulk surface and underground methods, selective extraction through flotation and leaching and global positioning system–geographic information system control systems that collectively facilitate mining at a massive scale. And yet, in spite of these successes and the boom that we have enjoyed in the last ten years, the industry is under pressure and the need for innovation and change is paramount.The major drivers for innovation are the need for increased quality in discoveries and mines and the need to interact effectively with communities and jurisdictions such that the benefits of quality mines are recognised and enjoyed widely.We are still making new discoveries around the Pacific Rim and elsewhere, but many argue that the quality – grade and accessibility – of these discoveries is decreasing. The net result is that explorers are delivering resources and reserves for development at lower grades and with higher capital and operating costs than current operations. For mining, the increasing age of many existing operations contributes to increasing costs, which, when combined with decreasing cut-offs and lower grades, also results in declining quality. The combined picture does not look good.Just as the pressure to improve performance and margins in the face of declining inputs increases, we are simultaneously faced with increasing societal demands for improved environmental performance and sustainable practices. This is most apparent at the local, community level, where opposition ultimately leads to delays or even cancellation of new projects. Quality is again the issue – quality of the initial and ongoing engagement and quality of the proposed mine in terms of environmental and economic performance.CITATION:Thompson, J F H, 2015. Exploration and mining – the need for innovation , in Proceedings PACRIM 2015 Congress, pp 45–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

During the past three years there have been several parties prospecting for oil in the Stat6 of Queensland, and It was: gratifying to read the newspaper headlines last Christmasabout the discovery of oil in the Moohie Nol Well. This discovery was not only a welcome Christmas present for Australia but marked up another success for the seismicmethod in exploration for oil.The purpose of this paper is to discuss the operationaI aspects of seismic work in Queensland with-emphasis on shot-haledrilling. The paper is based upon the experience of one particular seismic survey which began in December of - 1959 and is still inoperation. This survey is being conducted by the Petty Geophysical Engineering - Company of San Antonios, Texas, and the Queensland area involved is in the general vicinity of Quilpie, Dlackall and Charleville.

Jan 1, 1962

The recent boom in the mining industry has lead to some unique challenges in successfully operating processing plants. With high turn-over rates of both operators and technical staff, and many experienced personnel leaving regional sites for city based jobs there is often an onsite knowledge vacuum and this in turn puts pressure on both site training departments and senior metallurgists to provide the relevant skills to the continuous stream of new staff. Frequently both operators and new metallurgists are instructed on a æhow-toÆ basis rather than giving them the understanding as to why tasks are performed and decisions are made. This paper has been written with the plant operator and metallurgist in mind and aims to provide suitable material to be incorporated into a site training manual. Topics have been broadly divided into the following categories: factors that operational staff can control; including pulp density, air addition rate, froth depth, particle size and reagent type and use; factors that operational staff cannot control; providing general information on bubble size, froth stability, pulp chemistry and the mechanical effects of the rotor/stator system; and process improvements. Each topic is discussed with a view to clarifying the key process variables that need to be understood and optimised in an industrial operating plant.

Jan 1, 2009