Search Documents

The patterns of occupational health pro- grammes in mining and metallurgy are discussed in relation to the impact of chemical and phy- sical hazards on the health of workers in these fields. Mining and metallurgy are quite unique in that their history and practice embrace virtually the total spectrum of occupational health problems and hazards as understood today. A panoramic concept of the possibilities would comprise the following fields: 1. The Pneumoconioses or Dust Diseases. 2. Physical stress due to exertion, and exposure to heat and humidity in deep mines. 3. The toxic effects of various metals in the mining of ore. The most obvious are lead, mercury, arsenic and manganese. 4. Diseases associated with mining. These include leptospirosis, ankylostomiasis and mycotic infections of the skin. 5. The Beat Diseases of coal miners working in narrow seams. 6. Illumination problems and miners nystagmus. 7. Geographical and climatic problems

Jan 1, 1975

By Roberts T. J, Thomson I. A

Mill scale, which contains a high proportion of magnetite and wustite, was added to the feed to the Whyalla grate kiln pellet plant during the production of acid pellets for domestic consumption. Its addition resulted in increased production -rates together with reduced consumptions of bentonite, fireclay and fuel. Mill scale was particularly beneficial when treating feed containing difficult to process, earthy, high ignition loss iron ores. Test work in the laboratory and subsequent plant experience showed that the magnetite and wustite oxidised in the drying and preheat sections of the travelling grate. The additional heat reduced gas flows through the grate kiln system, aided the drying of green balls containing earthy ores and increased the preheat strength of the balls. These advantages were offset to some extent by higher power consumptions to grind the harder mill scale and process difficulties caused by the contamination of mill scale with oil and coke.

Jan 1, 1974

By K Uchino, M Inoue

Self-potential anomalies are generated by fluid pressure gradient, by temperature gradient or by chemical gradient. On the basis of this principle, a new technique is proposed to locate the fire source of spontaneous combustion of coal by the self-potential method. In order to investigate whether this method can be applied to locate the spontaneous combustion of coal in practice, surveys of self-potential distributions were undertaken in a coal waste pile undergoing spontaneous combustion. The results showed that there is a negative centre of the electrical potential distribution in the measurement area. The potential in this centre is about 140 mV lower than that in the surrounding area. Moreover, the negative centre of electrical potential distribution almost overlaps with the high temperature zone. Therefore, it is concluded that it is possible to locate the heat source by the measurement of self-potential distribution.

Jan 1, 2005

By Nickelsen J, Theisen KG, Hansen PH

The use of stationary calciners in the processing of aluminium hydroxide has emphas- ized the importance of Bayer hydrate properties with respect to particle breakdown during calcination and subsequent treatment. Test results from calcination of several Bayer hydrates to sandy alumina in the FLS Gas Suspension Calciner (GSC) were obtained in a 250 kg/h pilot plant unit. Particle breakdown during calcination was influenced by content of solid sodium oxalate, trapped in the hydrate particles and operating gas velocities. Owing to the design and operational principles of the GSC it is possible to reduce particle breakdown to at least the same as what is found in long rotary kilns. Other major advantages reviewed are obtained through simplifications in plant design and operation, pointing to low specific power and heat consumption, and generally low production costs, thereby providing an attractive alternative to fluid-bed calciners.

Jan 1, 1981

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986

On the 17th November, 1964, a new No., 2 lead blast furnace was blown in at Port Pirie. The furnace departed from previous designs by incorporating a centrally located continuous tapper for both lead bullion and slag. The use of a central tapper permitted a simple and effective layout for the handling of both products. Considerable development was necessary to bring the furnace to its present level of efficiency. Units vital to the continu- ous operation were developed to allow quick replacement, thus ensuring high time efficiency under varied operating and maintenance conditions. The furnace was designed with the following objectives in mind, 1. increased crucible life, 2. elimination of oxygen for slag tapping, 3. higher temperature slag for fuming operations-, 4. less operator skill needed, 5. reduced tapping tool consumption, 6. elimination of settler skull and scrap lead, 7. better control of blast air distributi.nn. And

Jan 1, 1975

By Ueki S

Underground coal gasification (UCG) is a promising process for obtai- ning energy from coal, which is either unmineable with current mining techno- logy or uneconomic to recover, using conventional methods, in the present energy market situation. There are several coal fields, which could become new coal reserves, if the UCG process were successfully applied. In the 1960's Japanese researchers made a number of basic studies and field tests into UCG, although not all of them produced favourable results. This paper reviews Japanese research on UCG. This includs basic studies into coal gasification using a small, tube reactor fed by air and oxygen, and also large scale model stu- dies(reactor size of 8.Om x 2.4m x 1.5 m). Field test results from Akabira colliery in Hokkaido and a feasibility study of power generation using UCG from a coal field in Hokkaido are also Presented.

Jan 1, 1987

By Richards AB

This paper describes the ENVIB software system, which has been developed in a menu-driven form to aid in the monitoring and assess- ment of vibration caused by routine blasting operations and for research and development projects. The paper gives an outline of the capabilities of the system by means of screen-dumps and a general descriptive commentary. Technical notes have been added where appropriate to further describe the system. The ENVIB system covers: I . Analysis of blast vibration results, and preparation of graphs and tables for control and estimation purposes. 2. Effects of atmospheric conditions and air vibration propagation. 3. Real-time acquisition and analysis of analogue blast vibration sig- nals directly from transducer equipment or from FM tapes. 4. Analysis of digital files on floppy disc or transferred via the serial port from blast monitoring equipment. 5. Transfer function calculation for structure response studies.

Jan 1, 1988

By Innes J. A

The structural variations occurring in pellets of finely divided mixtures of iron ore and coke breeze, metallized by firing at elevated temperatures, have been examined microscopically. For any given pellet composition, time and temperature are the two most important factors in determining the development of the bonding processes.INTRODUCTIONThe success of sintering and pelletizing processes in the agglomeration of fine iron ores for blast furnace use has brought about rapid changes in thinking relative to methods of preparing furnace burdens. Increases in productivity with the use of sinter emphasize the advantages of a stable, uniformly sized furnace feed. Current practice is to produce a self-fluxing sinter containing most of the lime requirements of the furnace incorporated as a stable medium (Figgis and Charker, 1962). The elimination of fine material from the burden allows greater stack permeability and smoother operation.Sintering and pelletizing of iron ores with or without the incorporation of fluxing compounds has conditioned operators to the extent that it is now considered possible that all components of the burden may eventually be beneficiated in one form or another. Investigations are in hand to improve the quality and sizing of coke, which occupies the major part of the burden volume (Callcott, Innes and Brown, 1961; Innes, Gregory and Worner, 1963). Interest is also being revived in methods of pre-reducing iron ores prior to charging to the furnace (Hansen, Melcher and Fine, 1961). Recent experiments in a small experimental blast furnace (Melcher, 1963) show that charging of semi-metallized pellets can give rise to a production increase of 55 per cent...

Jan 1, 1963

By Wyborn L, Giddings J. W, Plumb K. A

The McArthur, Balma (new name) and Habgood Groups are thick (up to 4.5 km) correlative sequences of shallow water evaporitic carbonates, mudstones and sandstones that are exposed largely within the Batten, and southern and northern Walker Fault Zones (Batten and Walker Troughs) of the McArthur Basin respectively. Recent re-mapping of the Walker Fault Zone has provided data for refined stratigraphic correlations between these groups. Two significant hiatuses are now recognised within the Balma Group (base of Vaughton Siltstone and base of Yarrawirrie Formation) and these may represent tectonically-generated sequence boundaries which may correlate with similar local hiatuses within the McArthur Group such as at the base of the Teena Dolomite and Lynott Formation respectively.

Jan 1, 1994

By S Juras

To our geologists at Eldorado Gold Corporation, the release of the gold assays on a new ore zone causes a flurry of excitement. But to our metallurgists, that news is often greeted with the question ‘What’s the sulfur grade’? In our company, we operate and manage projects whose end-product will either be auriferous sulfide flotation concentrate or gold doré. Almost all of the steps in the ore processing are related to sulfur (in this paper specifically sulfide sulfur). So why do we geologists wait until late in a project or into production before collecting sulfur data for mine planning and ore control purposes?Gold deposits associated with sulfides commonly use a metallurgical process that begins with a flotation step to recover gold into a smaller mass known as flotation concentrate. Often, this step solely targets the sulfide minerals with gold only coming along for the ‘ride’. As a result, the gold grade in the concentrate is primarily influenced by the ratio of gold to sulfur in the feed. Should this concentrate require a refractory process downstream (eg pressure oxidation), knowing sulfur grade is critical as sulfur controls heat balance in the process. Regardless, we need sulfur models to be as robust as gold models, and created much earlier in the project evaluation process.Sulfur models require quality data collected at the same density as gold samples. Analytical methods must match expected grade ranges and quality assurance quality control (QA/QC) protocols and must be of the same integrity as in use for gold. Sulfur models will then be created by their own data analyses, interpolation protocols and validation. Furthermore, ore control systems should be designed for regular sulfur monitoring to ensure and enhance downstream value. Given time it should become habitual for geologists to likewise ask, ‘And what’s the sulfur grade’, or more specifically, ‘What’s the gold to sulfur ratio’?CITATION:Juras, S, 2017. Sulfur – the new geometallurgical grade in gold-sulfide deposits, in Proceedings Tenth International Mining Geology Conference 2017, pp 199–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R R LARGE

In the past decade mineral deposit models have become an important tool for the exploration geoscientist. By combining genetic theories on the formation of particular deposit styles, with geological, geochemical and geophysical criteria relevant to ore location, it has been possible to more effectively focus exploration effort to the regions and local targets which have the best chance of success. However, such models have their limitations, and must be carefully and critically applied and continually updated as new technical and research information becomes available.

Jan 1, 1992

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005

By J Rubio

This work presents design features of an innovative in-line mixing helical (coiled) reactor for flocculation and flotation as a solid-liquid separation process for suspended particles (including liquid droplets). The device has been named flocs generator reactor (FGR), a compact system whereby the flocculation of particles is assisted by the kinetic energy transfer from the hydraulic flow through the reactor and/or by the injection of microbubbles (30 - 70 ¦m). The flow mixing presented a plug flow regime with a low dispersion degree, promoting the required hydrodynamic conditions to disperse the polymer flocculant (cationic polyacrylamide) and to generate æstrongÆ flocs of Fe(OH)3 or clays (as colloidal model systems) with aggregation using an anionic polymer, Al2(SO4)3 and poly aluminium chloride (PAC), and oil emulsions destabilisation with a high molecular weight cationic polymer. The solid-liquid separation of the flocs was then achieved either by settling or by flotation with microbubbles. This paper discusses advances in this new in-line flocculation-rapid flotation device to remove æaerated aggregatesÆ, aggregates with entrained and entrapped bubbles. Studies were carried out with different models of FGRs (varying the length:volume ratio) and process efficiency (mainly kinetics) evaluated as a function of polymer concentration and some operating parameters, namely, feed flow-rate, air:solids ratio and residence time. Results showed that the aerated flocs are readily floated with rising rates in the order of 120 mh-1, values higher than those obtained for the settling of the non-aerated flocs (18 - 24 mh-1). The FGR requires short residence times and generates dense, well structured flocs (with a mass fractal dimension, dF of about three) which withstand high shear forces. Mechanisms involved appear to include small bubble formation and their rapid occlusion (entrapment) within flocs, nucleation of bubbles at floc/water interfaces, polymer coiling as a result of æsalting outÆ effects at the aqueous/air interface and plug flow type of mixing (flocculation). Successful examples of emulsified oil and solids removal from water are shown and because in all cases high efficiencies were obtained (>90 per cent removal). Due to the high process efficiency and high loading capacity shown, the FGR appears to have good potential as an in-line flotation-separator device in applications requiring high rate solid-liquid or liquid-liquid separations.

Jan 1, 2005

By N Esmaeili, M Saghaeian, L Hosseini, V Sheikhzadeh, R Hejazi

Ore roasting has long been used for beneficiation and assay upgrading of different ores. In this process, which is mainly used for sulfide ores, the ore is heated to a high temperature. More specifically, it is a metallurgical process involving gas-solid reactions at elevated temperatures. Some types of Iron ore are weak in magnetic properties. Hematite, goethite and limonite are classified in this group. Unlike magnetite, which shows strong magnetic susceptibility, these ores are hard to beneficiate through magnetic separation route. Many researches have focused on gravity separation and flotation routes for upgrading these ores and these methods have also been utilised in the industry. One of the methods to whose industrial application less attention has been paid is magnetising roasting in which the non-magnetic iron ore is transformed to magnetite which is further beneficiated through magnetic separation. In this study, magnetising roasting tests have been performed on one goethite sample in order to check the feasibility of using this method for this specific ore in industrial scale. It is worth mentioning that high intensity magnetic separation have been performed on this sample before but the achieved results were not promising. Results have revealed that through magnetising roasting magnetite content of the ore could be increased from 1.7 per cent up to about 25 per cent. FeO content of the feed sample was increased from 1.03 per cent up to around 9.25 per cent. Also optimum size distribution for achieving the best results in magnetising roasting for this sample has been determined through this study. The best results were achieved when the ore size was 0–10 mm. The effect of coal ratio, time and temperature on the process have also be studied. A coal ratio of 5 per cent, time of 30 min and a temperature of 850°C were determined to be the optimum conditions. Finally, the technical feasibility of utilising magnetising roasting for this specific ore has been confirmed.

Aug 24, 2022

By H Thanasekaran, J Kohmuench, B Seaman

To achieve an efficient separation in the flotation process, valuable particles need to be selectively segregated from the gangue while utilising a minimum number of flotation stages. TodayÆs existing flotation technologies are effective for fine particle size classes; however, limitations due to particle buoyancy and bubble-particle detachment restrict the effectiveness of traditional flotation approaches on coarser particles. As a result, flotation circuits are generally configured to process only fine particle size classes in order to maximise recovery in the primary stages. Eriez has invented a novel flotation technology, the HydroFloat, which overcomes these limitations by carrying-out flotation in a dense, fluidised-bed medium allowing for the recovery of coarse particles (>0.250 mm). Over the last 15 years, this technology has been successfully applied to industrial minerals with several full-scale units installed to recover particles up to and exceeding 3 mm diameter in primary flotation circuits. This paper includes discussions on the history of this technology, process theory, existing applications, and a review of recent sulphide-based laboratory test work conducted for Newcrest mining and others. Benefits of this approach, such as improved recovery, low energy consumption and reduced reagent addition will also be reviewed.CITATION:Kohmuench, J, Thanasekaran, H and Seaman, B, 2013. Advances in coarse particle flotation - Copper and gold, in Proceedings MetPlant 2013 , pp 378-386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Recepoglu O, Tolun R, Yavasoglu N, Bulutcu AN

Scheelite was floated from a low-grade (0.28 per cent W03) calcitic (96.30 per cent CaCO3) scheelite ore using oleoyl sarcosine as collector and alkylated 8-hydroxyquinoline as modifier. Compared to oleoyl sarcosine alone, the grade and the recovery of scheelite concentrate were increased from 8.07 per cent to 33.54 per cent and from 55.1 per cent to 73.4 per cent, respectively. Infrared studies with pure calcite and scheelite minerals showed that while alkyl oxine is adsorbed on the scheelite surface, it is not adsorbed on the calcite.

Jan 1, 1993

By Riley S. J

The basic aim of mine planning is to design mine layouts and schedules that achieve optimisation of operations, minimum cost and maximum resource recovery. Successful accomplishment of this aim is facilitated by timely and comprehensive rehabilitation planning commencing at the pre-feasibility stage and continuing until the end of mining. Incorporation of a final landfomt design for waste rock dumps in a mine plan requires a prediction of surface stability, which may be achieved through erosion modelling. Erosion prediction models can be placed in two broad categories: soil loss prediction models eg USLE and CREAMS, and geomorphic models such as SIBERIA. A waste rock dump landform design based on selected slope form and grade and drainage systems should be developed as part of planning. A digital terrain model (DTM) of the landfonn should then be produced which can be modelled for long-term erosional stability using pre-determined parameter values. If acceptable standards of stability are not achieved, the landform should be redesigned and remodelled until the desired result is obtained. The planning process incorporating models requires knowledge of spoil or waste rock properties and model parameter values. This information is site specific and can be obtained from drill cores or costeans at the pre-mining stage and from spoil or waste rock during the mining stage. Realistic model parameter values are critical in post-mining landfonn design and can be obtained by several methods, including rainfall simulation, monitoring, geochemical analyses and grain size analysis.

Jan 1, 1994

By A Manfrino

The Iron Bridge magnetite mine and infrastructure project is currently in development as a joint venture between Fortescue Metals Group, Formosa and Baosteel. It is supported by an extensive database of reverse circulation drill hole samples analysed by X-ray fluorescence (XRF), with a large subset tested for concentrate mass recovery, concentrate and tail grades by Davis tube recovery (DTR) testing. A limited number of rock physical testing results, including unconfined/uniaxial compressive strength and crushing work index, completes the database.By combining all available information – assays, DTR results, geology, stratigraphy, mineralogy and rock physical results – and using multivariate statistical analysis techniques, the impact of the critical factors that control concentrate quality, mass recovery and grindability characteristics have been outlined. A set of geochemical groups was created by using a cluster analysis technique from the combined XRF-DTR data. These groups allow optimal separation of material with consistently high concentrate Fe grades and mass recovery. This approach is superior to domaining based on stratigraphic logging or mass recovery as it is commonly used in standard magnetite estimation models. Using the results of a normative mineralogy study, the main geochemical groups were given a mineralogical profile fitting their geochemical characteristics. These findings further refined the understanding of the link between the process characteristics of the samples and their geochemical signature and mineralogy.The geochemical grouping defined on head grades and DTR concentrate mass recovery was generalised into a ‘geomet’ code based solely on the routinely assayed head grades, thus bypassing the need for systematic DTR testing. The geomet code identifies spatial domains with homogeneous geochemistry, mineralogy and process characteristics in both oxide and fresh material that form the basis of the current Iron Bridge resource model. The allocation of geometallurgical characteristics in terms of concentration amenability and concentrate characteristics on a block-by-block basis over the whole project allows for an optimum mine schedule and plant feed. This ensures that the desired concentrate characteristics and mass recovery can be better predicted over the life-of-mine, thereby improving the mine’s economics and stability by derisking the mine schedule and optimising the performance of the concentrators. A key benefit of the geomet code devised for the Iron Bridge mine is that it can be attributed in an automated manner to all samples analysed for a routine XRF analytical suite, from exploration to blasthole drilling. This allows each sample to be allocated to a geometallurgical material type with predictable process response in terms of concentrate mass recovery and concentrate quality without the need to complete systematic DTR testing.A standard multivariate analysis coupled with a cluster analysis has allowed the linking of interdisciplinary results between geology, mineralogy, geochemistry, process and metallurgy to better understand, predict and ultimately mine and process the Iron Bridge deposits. This allows plant operations and product quality to be optimised through each stage thanks to the predictable ore characteristics embedded in the mining model.CITATION:Manfrino, A, 2015. Unravelling the factors impacting on concentrate quality by geometallurgical data analysis at Fortescue Metals Group’s Iron Bridge magnetite mine, in Proceedings Iron Ore 2015, pp 567–578 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Ellis

In January 2008 Chirano Gold Mines Limited committed to expansion of the Chirano Gold Project from its existing design capacity of 2 Mtpa ROM ore to a new design value of 3.5 Mtpa. In addition to increased throughput, the design had to contend with increasing ore hardness and competency, while at the same time make cost effective use of existing equipment with minimum disruption to existing production. The solution adopted involved some novel approaches including tertiary crushing and operation of the SABC circuit in overflow ball mill mode and parallel elution with a common acid wash column. This paper describes the approach taken to the design of these elements to achieve a cost effective and safe capacity expansion.

Aug 8, 2011