Search Documents

By Keyte SG

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.1mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80% and mass yields of less than 1% can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

By M Parcell

"Ventilation risks in an underground mine have essentially remained the same for centuries, yet theevidence suggests that there are many coal mines that have failed to adequately control these risks.The conduit for the knowledge learned by previous generations exists in the mining legislation. In an ideal world, mines would not need legislation to tell them what to do; they would resolve the risks to an acceptable level so as to protect the safety of persons in the mines based on the acquired knowledge. There will be some who have been personally aff ected by a mining disaster but for the majority they will be remembered as a vague recollection of an event from long ago. The mining legislation is the repository for the knowledge and outcomes from inquiries of past disasters. The challenge for the current generation, and the generations to come is to appreciate the legislation that exists, so as to not ælearn the hard wayÆ. In reviewing most disasters there is comment or discussion on the adequacy of the legislation, which ultimately results in some amendment to the law. For each person, there is an increasing responsibility to ensure that the same mistakes are not repeated. Understanding the legislation, its history and its purpose is the fi rst step in ensuring thatventilation risks are eff ectively managed. Failing to do this will be disastrous. This paper discussesthe relevance, importance and potential pitfalls of coal mine ventilation regulation."

Jun 1, 2012

By B Twidle, D Bertoldi, J Meikle, R Dunne

The Waihi Gold Mine is situated in a high rainfall area (annual average of over 2 m) on the North Island of New Zealand. Water treatment and discharge at the mine has been ongoing for the last 25 years. The first water treatment plant consisted of a æstandardÆ water treatment facility (ferric chloride precipitation) and cyanide detoxification. With time the project has expanded and the volumes of water increased requiring additional treatment methods (reverse osmosis) to meet the water quality for discharge. This paper will provide information on the historical development of the water treatment flow sheets, performance data and operating costs.CITATION:Bertoldi, D, Dunne, R, Twidle, B and Meikle, J, 2013. Water treatment at the Waihi Gold Mine, in Proceedings World Gold 2013 , pp 503-508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By B Tessier

Checking the quality of a blast may be considered as subjective. Checking this quality will require measuring objective parameters. One of them is the resulting fragmentation of the blasted product. Numerous fragmentation æmeasuringÆ systems have been developed and marketed, based on image-processing. This presentation of FragScan will illustrate advantages and difficulties when using such a system. FragScan is essentially defending a policy of large and representative sampling. The purpose is to show how fragmentation is discriminating both productivity and profit of quarry operations on a blast-by blast basis. The next step will then be to ædriveÆ the blasting process to reach a æbetterÆ fragmentation. Other applications require the fragmentation as an essential result: this is the case for large boulders used in structure-reinforcement. Several case-studies have shown that FragScan can be used for quality-control, checking size-distribution of the product according to the requirements of the end-user. Only clear thinking about the precise use of such a æmeasurementÆ will further the success of this task.

Jan 1, 2001

By H Zhai, C Zhang, I Canbulat, K Yui

Sedimentary rock is a lithology that is commonly encountered in mining practices. Their properties, especially the resistance against weathering, are often of critical importance to long-term engineering stability due to their ubiquitous existence on the earth’s crust. The weathering of rocks is a complex process that involves physical degradation, chemical and biological erosions. In this study, the impact of physical weathering on four common sedimentary rocks, namely sandstone, siltstone, limestone and shale, are simulated in the laboratoryoratory environment taking into consideration the impact of preservation condition, temperature and time. In order to optimise the design of the experiment, Taguchi’s design of experiment method is implemented based on the L16 orthogonal array and selected simulation conditions. The weight and dimension variation, fracture intensity, slake durability, and uniaxial strengths of specimens are then tested to quantify the impact of weathering under various conditions. The results indicate that weathering significantly influences the strength of shale, siltstone and limestone but not sandstone. The impact of weathering on dimension variation is insignificant. For soft rocks, most physical weathering took place after second cycle of simulation, resulting in strength reduction up to 100 per cent (disintegration) but generally in a range from 28 per cent to 32 per cent. Additionally, time is the most important factor contributing to the physical weathering of weak rocks, followed by residual, preservation conditions and temperature. Last but not least, some shales, depending on the content of clay minerals, tend to develop significant fracturing or even disintegrate under the influence of weathering.

Nov 29, 2022

By B Besa

Australia is a world leader in the design and operation of mines accessed by the decline method. Literature indicates that a number of metalliferous underground mines using the decline system are also increasing steadily. This increase has generated a great deal of interest in underground haulage systems in future due to the huge costs involved in the development of declines. Studies have also shown that the current method of accessing orebodies by the conventional decline method has proved to be expensive, especially for narrow vein deposits. This is because decline development costs are influenced by mine planning and design parameters as well as available haulage systems that the mining engineer can choose from. The current access method suggests that more waste material is being extracted because of the size of decline openings adopted (5.5 mW and 5.5 mH). Also the conventional 1:7 decline gradient and turning radius of 20 m makes decline lengths, as well as the duration of development, excessively longer. This paper discusses results of a mine design case study with monorail technology as a method of accessing and developing the decline. The proposed system is economical, has high advance rates and offers a significant reduction in capital expenditure. The study compares costs, development metres and the duration of decline development using the monorail system with the conventional (truck haulage) access method. Results obtained indicate that the monorail technology has the potential to reduce the decline length by over 62.6 per cent and decline costs by 63 per cent for the case study. The monorail system also reduces the total capital development costs by 22 per cent for the same case study. Due to rapid development resulting from increased advance rates and the shorter decline length coupled with smaller decline openings, the time to access the deposit reduced by 71.8 per cent. This case study demonstrates that the economics of narrow vein deposits can be improved significantly by using the monorail system of decline development.

Jan 1, 2008

By T Nixon

A common problem for many mines is insufficient total primary airflow or insufficient airflow in the correct places as the mine changes over its life. This has a number of impacts on the business operation and may result in the need for a major and unexpected capital upgrade of the system, cancellation of a planned production increase, reduction in production targets, increased operating costs, failure to provide contracted metals to customers or acceptance of substandard conditions in the workplace. In some cases, it can even result in premature closure of the mine. In recent times, higher metal prices have given an expected economic boost to many mines, potentially prolonging their life but simultaneously requiring the mine to develop to deeper depths or requiring assets such as shafts and fans to have their service life extended. Insufficient primary airflow is a particular problem in deeper mines as the ventilation circuits become longer, more convoluted, have higher shock losses and the actual airflow requirements increase due to a combination of leakage, dispersion of the workings and the problems of managing the additional heat loads due to higher virgin rock temperatures and autocompression. This paper discusses the reasons why mines experience unexpected shortfalls in primary ventilation capacity with its associated impacts on metal targets, profits and frequently on the health, safety and morale of the workforce, as well as its productivity.

Jan 1, 2008

By E Acu±a, B Prosser, R Alvarez, K Wallace

This paper describes the ventilation analyses performed for the access tunnels at the New Level Mine project (NLMP) at CodelcoÆs El Teniente operation outside of Rancagua, Chile. This new mine is anticipated to reach a final production of between 137 and 180 kt/d. Production from the NLMP is scheduled to start in the year 2017. The main access tunnels (MAT) are approximately 9 km in length, with one for personnel and supply access and the second one for ore extraction through a conveyor system. These two tunnels are a critical component of the initial stage 1 development and will be constructed independently of the existing mine workings. The tunnels were originally designed to be constructed with two tunnel boring machines. However, later analyses changed the construction approach to a conventional drill and blast technique. Because the design included two mid-tunnel ramp-to-surface connections, conventional mining methods would allow for development of the tunnels with multiple working faces to achieve a more rapid schedule. This paper presents the initial baseline considered for the ventilation design and the optimisation methodology applied by Codelco to minimise the airflow and pressure requirements of the ventilation system. Modifications to the design resulted in the addition of strategic airways and raises that could provide a saving of approximately 1 MW, when compared to the original design.CITATION:Acu±a, E, Alvarez, R, Wallace, K and Prosser, B, 2013. Ventilation considerations for the new level mine project access tunnels, in Proceedings The Australian Mine Ventilation Conference , pp 203-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A Roshal

It is anticipated that many future uranium mines in Australia will be using the in situ leaching mining process. It is fair to say that close to one third of uranium production will be generated by this method, whilst the other two thirds will fall on the uranium generated from hard rock mining and other mining methods, such as traditional open cut mining. For other types of deposits the in situ leaching mining method will remain the best technological, commercial and environmental alternative. It is important to identify and prevent all risks involved in uranium mining. The expertise in this subject is limited. Over the years there was only one mine using the in situ leaching process for uranium extraction in Australia. Computer simulation of propagation of leachate during and after the uranium in situ leaching is a crucial factor, not only for addressing the environmental concerns, but also for the most efficient recovery of the deposit. The decontamination can be modelled for a period of up to 100 years, with the acid neutralisation forecast for a period of up to 400 years. The results of the modelling are paramount for definition of the reserves, efficiency of the mining method and the environmental impact statement. The accuracy of the hydrogeological modelling and carefully selected environmental management program enables a mining company to quantify and minimise the impact of the mining activities on the regional aquifer and to prevent environmental disasters. In the study, the completed hydrogeological model allowed the client, the authorities and the community to make an informed decision about the environmental impact of the in situ leaching of uranium. In particular, the model proved that neither during the mining, nor during the neutralisation the toxic elements would interact with the local catchment area.

Jan 1, 2008

By P Holtham, W Valery, P Baguley, A Jankovic

There is a growing interest in magnetite ores because of the increasing demand for this commodity. With these ores, there is significant cost associated with milling the ore to fine sizes using ball mills in closed circuit with hydrocyclones. Cyclone classification efficiency tends to be poor due to the large difference in density between magnetite and gangue. This decreases the grinding circuit efficiency and results in over-grinding of magnetite. The objective of the work described in this paper was to modify the Bond locked cycle milling test procedure to quantify the loss of grinding circuit efficiency due to the mineral density effect. The locked cycle test procedure described here includes a stage of magnetic separation treating the closing screen undersize, which allows simulation of magnetite classification. The effect of classifier efficiency on low-density particles (non-magnetics) was simulated by altering the proportion of closing screen undersize bypass returning to the mill. Using a magnetic separator and a screen in the magnetics stream, different proportions of the magnetic fraction can be bypassed, thus allowing simulation of the effect of particle density on classification efficiency. This laboratory test work has confirmed that the impact of mineral density on cyclone efficiency subsequently has a crucial negative effect on ball mill circuit capacity. The results are in good agreement with reductions in capacity observed in practice. Multicomponent grinding and classification models were also developed in the LIMN software environment and were able to successfully simulate both the industrial and the laboratory ball mill circuit. The test and modelling procedures established in this project could be used for improved design of new magnetite ball mill grinding circuits as well as the optimisation of existing circuits.CITATION:Jankovic, A, Baguley, P, Valery, W and Holtham, P, 2015. Effect of mineral density for milling magnetite ores, in Proceedings Iron Ore 2015, pp 159–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By B King

A large number of mineral deposits contain regions in which it is economically beneficial to extract ore both via open pit and underground mining techniques. Current industry practice lacks an effective means to establish the extent of the open pit and underground mining areas for an individual deposit. We present a mixed integer programming model for scheduling both the open pit and underground mine that can be used to create a holistic extraction sequence for a specific deposit. The model considers both spatial and temporal elements of the open pit and underground mines in order to maximise the net present value of the entire deposit, while adhering to its production, processing and block sequencing constraints. By doing so, we can schedule the open pit and underground in concert.CITATION:King, B, 2014. Modelling open pit and underground production scheduling in concert, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By G Pitkin, D Sorley

The purpose of any consultancy is to provide a superior service for their client. Organisational structure is a key element in providing this service and differentiating between consultants.In an organic organisation the emphasis is on effectiveness, problem solving, responsiveness, flexibility, adaptability, creativity and innovation. Such an organisation is able to respond in a timely manner to change because employees are empowered to be creative, to experiment and to suggest new ideas. The process of innovation is triggered by employees throughout the organisation in a collaborative manner.Problem solving becomes a core competence of the consultancy. A multidisciplined approach arrives at superior solutions that are rigorous, holistic, achievable and often novel. It allows the mining consultancy to extract the most from a very talented and experienced team.This paper highlights the advantages of an organic structure for a mining consultancy and how to implement such a structure. It draws on examples of innovative problem solving from feasibility and strategic studies carried out in Australia and Africa.CITATION:Pitkin, G and Sorley, D, 2016. Organic management structure – its advantages in a mining consultancy, in Proceedings International Mine Management Conference, pp 155-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Asian countries are now facing very crucial aspects of urban living under the recession of the economy. The current situation is such that those hard aspects may make the living standards worse and worse in the next century, unless proper measures are taken on the infrastructure for urban lives. More than half of the population in Asian countries are now living in cities. Nowadays, the socio-economic development of the Asian countries has been closely linked to the development of world economy because of the border-less economy system. The population inflow to big cities is inevitable as the Asian countries step into an industrialised economy. Such a tendency will be further accelerated when Asia becomes a centre of financial business in the 21st century. The government of any country has realised the situation very well. The United Nations has established a specific agency to solve the problems caused by the rapid urbanisation. This global agency for urbanisation is named United Nations Center for Human Settlement and it is so called Habitat. There are three Habitat offices in the world, Nairobi in Kenya, Santiago in Chile and Fukuoka in Japan. The activities of Habitat offices cover a wide field of issues such as housing, urban development, infrastructure and environment, etc. Habitat Fukuoka Office is serving Asia and Pacific in co-operation with the government offices concerned.

Jan 1, 1999

The geotechnical and environmental aspects of heap leaching are very closely tied during design, operations and closure. Potential environmental impacts from heap leaching are mostly due to land disturbance and water quality issues, including both groundwater and surface water. Water quality issues are mostly related to containment design, which is primarily a function of proper sizing of the facilities and site specific liner design. Geotechnical analyses is the dominant discipline in providing cost efficient, operationally effective and environmentally sound heap leach facility designs. Much has been published on geotechnical aspects of heap leach design, for example Van Zyl, Hutchison and Kiel (1988) and Van Zyl (1987). This paper will emphasize a few specific aspects related to the geotechnical and environmental consideration for heap leach projects. These aspects are: ò site investigation; ò containment design; ò slope stability; ò heap flow dynamics; and ò closure design. Design of a heap leach project must consider not only the operating life but also closure and post-closure considerations. As a matter of standard practice, designing for closure is an extremely important concept. Not only is it important for environmental aspects, but experience also shows that projects designed for closure will be overall more economical for the total life cycle of the project. Closure considerations are also important during project feasibility evaluations to ensure that total life cycle costs are evaluated.

Jan 1, 1994

In contrast to the '50s and '60s, the period of the '80s and '90s seems likely to have low growth in demand but much greater levels of technological change. In such a climate there will be pressure on costs, productivity will continue to rise and competitiveness will be closely associated with maintenance of the most effective technology. The penalties for inappropriate investments, whether short sighted or mistakenly based on a particular view of the future, will be greatly enhanced. Accordingly, there will be a need for significantly improved anticipation of technical change and thus for better planning. Study of the funding and direction of the world's R&D effort can provide a useful input to the planning processes within industries and individual firms. Such a study also suggests some insights into the characteristics of those countries which have achieved substantial growth and high standards of living over the past two decades. These characteristics may offer significant reminders for our own development. The particular implications for the Australian minerals industry include the need for direction that is sensitive to changing market requirements and customer practice. This is not simply "more of the same." In particular it appears essential for both basic and applied R&D to provide a sound basis for the purchase and ongoing development of the new technology required to achieve international Competitiveness.

Jan 1, 1986

By P G. Fuller

The Woodlawn Mine near Canberra faced the challenge of poor ground conditions from the commencement of underground operations 1987. Talcose shears bounded the dense massive sulphides on both the hangingwall and footwall side of the orebody. In another area the talc existed not only on the edges of the orebody but through out it as well. The country rock was relatively weak shales compounded by a low stress environment that allowed the wall rocks to fall apart quite easily. The challenge for the operators was to overcome the poor ground conditions. This was done by attacking the problem from three directions:technology, how technology is applied, human relations and leadership by all levels of the Management team, and by ensuring that these processes meshed together well.Woodlawn in it early days as an underground mine enlisted the assistance of BFP (Formerly Barrett Fuller and Partners) as a second set of eyes to assist with the assessment of the ground control procedures. The results are discussed in this paper. The progression to this end result included:non-contract payment systems; ground control training for the full range of mining personnel; the development and enhancement of cable bolting and shotcreting equipment; the development of Practical Standard Work Procedures by mine operators; and innovative use of shotcrete and cables bolts to control extremely poor ground conditions.

Jan 1, 1998

 Increasing concern about the impact of alluvial mining discharges on the water quality of some West Coast rivers lead to a joint West Coast Gold Miners Associate, Trade and Industry funded study by Water Technology (NZ) Ltd. The objective of the study was to assess the treatability of West Coast alluvial gold mining discharges and to develop simple treatment systems which could be effectively adapted to a variety of sites in the region.   The approach was to apply standard water treatment techniques to field situations using low cost technology. Initially the various types of alluvial gold mining operations were identified then after preliminary site investigations and laboratory studies were carried out, site pilot plants were set up. The results of the trials particularly those using chemical aids were encouraging and it was found that chemical aid performance was largely dependent on the degree of mixing at and downstream of the chemical addition point. Design alterations to settling pond configurations in conjunction with optimised chemical addition yielded dramatic results in the form of reduced effluent turbidities.   A generalised approach to effluent treatment was developed and some of the specific 'mix and match' requirements were identified for different types of sites. The general conclusion is that improved physical treatment combined with good plant management and operation and (where necessary) chemical treatment, will produce water of acceptable discharge quality.

Jan 1, 1989

By D Hodson

Current classification of resources is entirely a subjective task. The various international reporting codes (such as the JORC Code) provide Competent Persons and practitioners with little specific guidance on the standard of work and levels of uncertainty required to classify resources into Measured, Indicated and Inferred. Furthermore, little guidance is given in the conversion of Resources to Reserves and the potential impacts on classification of uncertainties in the modifying factors. Working back from the intended use of the resource estimates, and in understanding the tolerance for uncertainty by the end user of such estimates, insights into the objective and requirements of classification can be determined. Following this approach a comprehensive set of (quantitative where possible) guidelines have been determined that will ensure resources meet the desired objective of each classification, and are consistent and comparable. The guidelines look at what is required for each step in the resource estimation process in order to ensure the final resource estimate meets the desired level of confidence. This approach provides a transparent, comprehensive, justifiable and largely objective method of classification. The implication of introducing such a guideline or approach is to highlight areas of a resource estimation that do not meet the requirements (ie drive the uncertainty beyond the objective) and then focus in on the risks that may flow on from that particular uncertainty, to mitigate or attempt to control those risks.

Jan 1, 2006

Zinc produced by pyrometallurgical processing techniques suffers the disadvantage of restricted market potential because of its impurity contents, typically lead and cadmium. Market zinc to the Special High Grade (SHG) standard can only be produced by reflux distillation refining, which is costly in terms of energy and equipment, and potentially capacity limiting. Recent published laboratory work suggested that molten salt electrorefining of zinc metal is a potentially much cheaper alternative to the reflux distillation refining. The extrapolation of the laboratory results to an industrial configuration, however, resulted in an estimated power consumption for electrorefining and associated costs offering no advantage over current reflux distillation practice. A review of this estimate now shows that a serious error in calculation was made, and that the energy consumption for the electrorefining of molten zinc would be an order of magnitude lower than that for reflux distillation refining. While this is a promising indication, further research is required before development towards an industrial scale operation is warranted. This would particularly relate to the extent to which adverse electrolyte deterioration may take place and its potential effect on the anode and cathode efficiencies of the process. This paper considers the laboratory investigations required to explore the industrial potential of the molten salt electrorefining of zinc and foreshadows some of the practical problems to be solved in further development.

Jan 1, 2000