Search Documents

By Gooday PE, Brech GE

Ore reserve categories used by Pancontinental Mining fall into one of three fundamental groupings: Geological In Situ Reserves Mining Reserves Production Estimates The first of these describes the total reserve within stated parameters without implication as to its mineability. The second is that part of the Geological In Situ Reserve which is considered mineable under a specific mining plan. The third is the Mining Reserve adjusted with appropriate dilution and recovery factors and thus represents the best estimate of the tonnage and grade of production. This practical three category system mirrors the standard steps traditionally taken in ore reserve estimation and readily conveys the basis of the estimates. An important, but secondary classification can be added to qualify the level of confidence in these estimates using the terms: Proved (or Measured) Probable (or Indicated) Possible (or Inferred) These terms can be applied to any of the fundamental groupings, but it is generally implicit that the level of detail required to produce meaningful Mining Reserves or Production Estimates would require the basic Geological Reserve to be at a Proved or at least Probable level of confidence. The application of these classification systems by Pancontinental is illustrated by reference to the Paddington Gold Project. The methods of calculation are described including the use of geostatistics. Reconciliations of actual production with predictions from reserves are carried out monthly and annually. To date there has been an excellent correlation with Production Estimates, based on both manual and geostatistical calculations.

Jan 1, 1987

By Mikula PA

This paper presents the results of in-situ and laboratory investigations into a mining method which utilises conventional continuous mining techniques to carry out two passes in thick coal seams, resulting in the development of stable pillars with relatively small width dimensions and heights up to 6 m. Geotechnical investigations included structural mapping, brightness logging and standard laboratory testing. Virgin stress was measured using overcoring techniques. Two approaches to pillar design were used in the study. These were; pillar design based on empirical formulae and laboratory testing, and pillar disign using calibrated mathematical models. A trial panel was developed at 300 m depth to study pillar deformation and stress changes due to mining. The extent of rib deformation was studied using borescopes and extensometers. In-situ geotechnical measurements were used to calibrate displacement discontinuity and finite element mathematical models of the coal seam. These models were then used to predict the behaviour of a small panel of pillars which were to be developed to 6 m height. The mining method was shown to be feasible provided adequate rib support was installed. The benefit of rib support was found to be two-fold, in that it increased confinement of the pillar in zones of low horizontal stress, while reducing horizontal stress relaxation in zones of high horizontal virgin stress. The possiblity of roof control by designing the small pillars to yield on retreat is discussed.

Jan 1, 1986

IT will be noticed, from the following contributed papers on the various plant, what an infinite number of parts are required to be kept in active operation in order to derive a resultant product of commercial value from the ores and materials received at the works. Crude ores and concentrates, in every degree of complex structure and resistance to treatment, are arriving daily from near and distant places, moreover their metallic contents are so varied that an outsider, unacquainted with the operations, would naturally wonder how it is possible that the rare elements are to be sorted out and classified into their true order, to meet industrial requirements.The proposition is necessarily not a simple one and owners of mining properties have naturally refrained from smelting their complex ores on account of the technical difficulties of attaining high efficiency and recovery of the metals, where limitations are imposed in procuring a variation of ores that lead to the best smelting and refinmg result. This difficulty obviously imposes many disabilities on the smelter, who is prepared to accept all such complex ores, and it may be said that were therenot available a large weekly supply of lead concentrates from the company's own mine at Broken Hill, of standard quality, much of the material being treated in the world today would certainly not be marketable.In order to sustain full efficiency, each section of the works must maintain its.true balance and synchronize with the requirements of such other departments as are dependent on its partially treated materials. This harmony of operations is not only imperative as regards tonnage output, but also relies on the condition of the resultant treatment by each plant, no large variations being permissible.The various officers are, therefore, dependent on one another to keep the order of the operations flowing regularly. This is accomplished by constant intercommunication and observation, as...

Jan 1, 1918

By P D. Erskine, A Hine

The current Queensland Government’s rehabilitation guidelines for post-mining landforms present a hierarchy of preferred outcomes for different areas within the mine site (see Figure 1). Within all areas, restoration of a ‘natural’ ecosystem is clearly prioritised as the preferred end land use, although it is not a mandatory practice. Beyond the official guidelines, there is also an implied preference for renaturalisation echoed in most environmental impact assessments and closure plans (Lamb, Erskine and Fletcher, 2015). In practice, however, ecosystem restoration does not extend to construction of a realistic topographic form, largely rejecting the ‘natural’ aesthetic implied by ecosystem restoration in favour of adopting a functional aesthetic in deference to standard engineering criteria.This presentation argues that the established disconnection between actual and implied landform aesthetics is indicative of a wider problem around end landform planning. It contends that such disconnects are the result of the impact of competing ‘ways of seeing’ (Bradley and Kearney, 2007) the same landscape, and reflect the struggle between, and inclusion of, these differing perspectives within the planning process itself. We propose that recognition of the complexity of landscape perceptions is key to improving post-mining landscape outcomes, and the misalignment between land use values and landscape aesthetics can be addressed by establishing an overarching framework for landscape preferences. As such, we outline the reality of stakeholder landscape preferences, and present a critical response to current planning practices within the life-of-mine (LOM).CITATION:Hine, A and Erskine, P, 2016. Recognising and integrating stakeholder landform expectations into life-of-mine planning, in Proceedings Life-of-Mine 2016 Conference, pp 154–157 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

WaihiÆs Cornish Pumphouse is located on the edge of town in a dynamic and changeable area where history affects the future. As in any successful project, ingenuity and team work have been significant factors in the planning and implementation of the buildingÆs relocation.   Work around the Pumphouse site commenced circa 1900 with preparation to sink the No 5 shaft. Construction of the pumphouse and the steam driven C pump was completed by 1904 with hints of what was to come evident in 1905 as the No5 Shaft collar had sunk 350mm in four years. By 1907 surface cracking developed over the Milking Cow cave area and in 1913 200 mm was cut off the main pumping rod as the ground was sinking at a rate of 25 mm per year.   In 1913 ground around No 6 shaft had subsided 600 mm.It was also the end of an era as steam gave way to hydroelectricity and electric pumps replaced the C Pump. C Pump was maintained as a backup from 1913 to 1929 and then finally scrapped. 25 years of underground caving operations removed approximately 400 000 cubic metres of ore leaving a 7 ha collapse crater that eventually became known as the mine lake.   On the edge of town a tension zone over the Royal Lode began to develop 50 m diameter chimney collapses as large scale blocks relaxed into unfilled stopes in the old Martha underground mine. After the 1999 collapse part of the main street was closed and after the 2001 collapse Hazard Zones were declared, more streets closed and areas evacuated and retired from residential use.   By 1984 the Pumphouse has approximately one degree of tilt and in 2002 tilt on the Pumphouse accelerated briefly and then settled down. Tilt accelerated again late in 2004 and a scoping study was initiated to define protection options for the pumphouse. The Martha Mining Licence requires Newmont to 'Take whatever precautions are necessary to protect the old Cornish Pumphouse adjacent to No5 shaft' and viable solutions needed to found.   Any work on the Pumphouse comes standard with a wide range of stakeholders, governing agencies and legal framework to consider. Land Information New Zealand (LINZ) is owner and administrator of the pumphouse.

Jan 1, 2006

Gold mineralisation at Wapolu lies within an exposed arcuate zone at the decollement contact between a basement dome of high grade metamorphics and an overlying ophiolite sequence. This contact was originally a thrust fault which has since become a decollement zone for gravity sliding in association with basement doming. Hydrothermal models for the gold mineralisation postulate an epithermal system in which fluids were channelled up the decollement with boiling of those fluids causing hydrothermal brecciation and subsequent gold deposition. The alteration assemblages, fluid inclusion data and geochemistry indicate that the upper levels of the system are exposed.

Jan 1, 1987

By A Riles

"Three issues of relevance in a modern tailings storage facility (TSF) are:geotechnical stabilitymanaging acid rock drainage (ARD) from pyritic tailingsmanaging the tailings from cyanidation of gold ores. Drawing on examples from both copper porphyry flotation and sulfide-hosted gold ores, this paper demonstrates that giving some weight and importance to the process tails properties upfront can influence the flow sheet and not only improve tailings management effectiveness but also impact positively on economics. In the case of a typical copper porphyry ore with moderate pyrite content, the rougher tail in a conventional high pH selective flotation step is usually classified as potentially acid generating (PAG). To avoid the generation of ARD within the tailings and the requirement for a costly plastic lining, subaqueous deposition is recommended, which in turn has negative implications for tailings stability, consolidation and closure. Adopting a neutral pH rougher stage rejects silicate gangue but recovers pyritic material to the cleaners for a subsequent selective flotation stage, often after regrinding. This effectively quarantines the PAG pyritic material in a much lower volume cleaner tail, which can then be appropriately encapsulated within a larger non-lined flotation tails facility. It also facilitates cyanide leaching of the cleaner tail for gold recovery, with the encapsulated tailings facility being suitable for cyanidation tails storage. A case study from Europe is examined. For gold ores where the gold is sulfide-hosted, but not refractory, a flotation route with cyanidation of the concentrate can similarly produce the majority of tailings as a benign flotation tail and again quarantine the low volume concentrate leach tail in a small encapsulated cell with appropriate residual cyanide management measures applied. Overall economics for intensive leaching of a low volume concentrate stream can also be surprisingly positive. A feasibility study design example of the process and TSF is presented. CITATION: Riles, A, 2016. An Integrated Approach to Optimising All Concentrator Products, Including Tailings, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 341–346 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Trembath

"One of the key risks to the success of a mining operation is the accuracy of the estimates of both the economic mineral and any accompanying contaminants contained within the ore reserve. Misrepresenting the mineralogical characteristics of the ore reserve can result in considerable financial investment in an operation that is in fact uneconomic and/or carries a significant environmental risk. This in turn can result in an unplanned closure of the operation with associated financial, environmental and social legacy. One way to minimise this risk is to undertake high density resource sampling to gain a better understanding of the resource characteristics. However, such an approach is expensive, time-consuming and often impractical. The risk of not having an accurate model is typically assessed during a feasibility study utilising a Monte Carlo simulation method or some form of sensitivity analysis. Importantly, the error margins used in these types of analyses are often based on subjective or very general criteria such as ‘professional judgement’ or an ‘industry standard’. This presentation introduces a conditional simulation method for developing a range of mineralogical distribution models. Based broadly on the method outlined in Journel and Kyriakidis (2004) the proposed approach develops this work further. It combines a geostatistical analysis of the available data with automated mine design software to provide a rigorous method for assessing the confidence in the mineralogical characterisation of the ore reserve. The process is based on simulating possible mine plans based on the statistical characteristics of the available resource sample data. These plans are then assessed against high resolution resource models generated using a Sequential Gaussian Simulation method. The outcome is confidence intervals for important characteristics of the ore reserve estimate relative to the actual resource. These confidence intervals are an objective and transparent measure important for assessing closure risks and represent an improvement over common practice.CITATION:Trembath, D, 2016. A simulation approach for improving the assessment of closure risks, in Proceedings Life-of-Mine 2016 Conference , pp 36–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By J P. Richards, M D. Johnston

The Porgera gold mine, located in the highlands of Papua New Guinea, produced 7.7 Moz of gold between 1990 and 1998. Reserves are estimated to be 12 Moz of Au. The deposit is associated with 6 Ma-old mafic alkalic intrusions emplaced at shallow levels into unconsolidated Jurassic and Cretaceous sediments, where they caused the formation of peperites. The mineralisation consists of an earlier base-metal-sulphide-rich stage with sericite-carbonate alteration (stage I), and a later phase represented by quartz-roscoelite veins (stage II). New styles of mineralisation and alteration have been recognised at depth in association with stage I. They consist of the assemblages magnetite-chalcopyrite-pyrrhotite and biotite-actinolite-anhydrite respectively. In addition, the recent recognition of adularia in some stage II veins (with roscoelite) confirms the similarity of this style of mineralisation with other adularia-sericite or low-sulphidation epithermal deposits.

Jan 1, 1999

By BLAKE DAWSON WALDRON

I must acknowledge my strategic adviser, Mr Lance Grimstone, who contributed to the development of this paper, and collated the text and figures.

Jan 1, 1994

By Offler R, Lau J, Lea J. F

The stratiform and vein-type pyritic silver-Iead-zinc-copper sulphide deposits of Sunny Corner, NSW are hosted by acid volcanic and clastic sedimentary rocks of Middle Silurian to Early Devonian age. The rocks have been subjected to low-grade regional metamorphism (prehnite-pumpellyite facies) and three phases of folding and four faulting events are recognised. Pyrite is intensely fractured, indicating brittle deformation. Chalcopyrite and galena exhibit deformation twins and slip planes indicating ductile deformation; sphalerite and chalcopyrite show straight and curved grain boundaries and dihedral angles of 120° as evidence of annealing recryslallisation. Sulphur isotope ratios for 22 samples from five deposits range from 1.7 to 10.7 per mil and average 7.4 per mil. Sulphur isotope data are similar to those from other stratiform sulphide deposits in acid volcanic rocks of Late Silurian age in the eastern Lachlan Fold Belt, especially Woodlawn and Captains Flat and together with other features of the mineralisation, suggest a volcanic exhalative origin for the Sunny Corner deposits.

Jan 1, 1984

By G Love, S Maher

In Victoria’s onshore Gippsland Basin, geology is driving brown coal developments, and geologists are key decision-makers. Prompted by volatile energy prices and the likelihood of a carbon constrained future, significant work has been carried out on the next generation of technologies to be applied to this giant resource. These include new-generation gasification technologies, coal conversion processes yielding products as diverse as diesel and fertiliser, drying technologies producing thermal and metallurgical coals and in situ conversion processes. However, coals aren’t coals, and brown coal available for new projects will have different quality parameters and mining economics from that currently mined.New projects are likely to be developed on coals with moisture contents averaging 60 per cent and corresponding low energy values. Whilst ash values will be low, averaging just 5 per cent (dry basis), this will at times approach 10 per cent, which is a level that would challenge the installed-generation technologies. Sulfur values will average 0.4 per cent (dry basis), but at times exceed 0.6 per cent, requiring technologies that address the potential for sulfur dioxide emissions. Whilst localised high levels of the fluxes iron (>1 per cent dry basis) and sodium (>0.3 per cent dry basis) would increase fouling of installed technologies, they may be suitable for selected next-generation technologies.Project viability for this next generation of technologies will be strongly influenced by mining cost, and geologists are playing a role in identifying higher-value coal. At its simplest, this is being achieved for open cut mines through regional, vertical strip ratio assessments, which are considered a first-order proxy for mining cost. Follow up assessments are incorporating mining and processing cost, coal quality penalties and product revenues. At a regional scale, it is informing the likely location and relative timing of future mine developments, as well as thinking around rehabilitation strategies, infrastructure and land-use planning.For deeper coal, factors like macro permeability, the ability to isolate seams from aquifers, groundwater chemistry, pressure temperature conditions, connection with groundwater recharge and in situ biota are being used as vectors to in situ coal conversion opportunities.Matching coal to the next generation of technologies has benefited from regional-scale geological studies of coal quality and mining economics, and has benefited from early engagement between geologists, technology developers and project proponents.CITATION:Maher, S and Love, G, 2014. Matching brown coal to the next generation of Latrobe Valley projects, in Proceedings Ninth International Mining Geology Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By G R. Hancock, J F. Martín Duque

Post-mining landscapes are required to geomorphologically and ecologically integrate with their surrounds (Martín Duque et al., 2015). Designing and constructing an erosionally stable landform is the first and arguably most important part of the rehabilitation process. Without an erosionally stable landform topsoil and nutrients are lost, shallow groundwater is depleted as well as when excessive erosion occurs, expose suboptimal materials. Here we examine the ideas of geomorphic design and rehabilitation and how the landform can be tested and enhanced using computer based design and landscape evolution models. Specifically we evaluate the complementary capabilities of landscape modelling (SIBERIA) (Hancock and Willgoose, 2017) and geomorphic design software (Natural Regrade with GeoFluv) (Bugosh et al., 2016), in order to maximise erosional stability on post-mining landscapes (Zapico et al., 2018). CITATION:Hancock, G R and Martín Duque, J F, 2018. Geomorphic design and landscape evolution modelling for best practice mine rehabilitation, in Proceedings Life-of-Mine 2018, pp 119–121 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By E R. Ramanaidou

Two unknown iron ore samples were found by a geologist from Ok Tedi Mining Limited copper, gold and silver mine at an old wharf site dedicated to a 1970s drilling program in Lake Murray in Papua New Guinea (PNG). These iron ore samples could not come from a PNG mine and it was decided that a study should be undertaken to understand their origin. Lake Murray is the largest lake in PNG with a total surface area of 647 km2. It has a high-water 2038 km long convoluted shoreline with seasonal water level changes (Osborne, Kyle and Abramski, 1987) and it is located around 200 km south of the Ok Tedi mine (5°13’25”S, 141°09’37”E). The petrology, mineralogy and chemistry of two Fe samples (Ok Tedi 1 and Ok Tedi 2) included optical microscopy, X-ray fluorescence (XRF) analysis and a comparison with worldwide iron ore deposits. The two rock samples were cut to produce two subsamples: (1) a polished thin section; and (2) a pulp that was used for XRF analysis including major, minor and trace elements. Ok Tedi 1 and Ok Tedi 2 were petrologically and chemically compared to a range of known iron ore samples from Australia, Brazil and South Africa. The petrological study of Ok Tedi 1 indicates that it is composed of granoblastic recrystallised hematite and the overall texture is uniform without any obvious original ‘sedimentary’ texture. Ok Tedi 2 is a ‘specular’ or platy hematite with recrystallised and fused grains. Using both petrological and chemical clues, the two Ok Tedi samples likely originated from the Iron Quadrangle in Brazil.

Sep 18, 2023

By BTrubT M

In the roast-leach-electrolysis process for the production of zinc, iron contained in zinc concentrates is converted to zinc ferrite during roasting. At Canadian Electrolytic Zinc (CEZinc), the Outokumpu Conversion process is used to simultaneously leach zinc ferrite and precipitate the iron as jarosite. These simultaneous reactions, while providing good process stability, require a compromise between optimum conditions for maximum zinc extraction and efficient iron precipitation. An improved conversion process has been identified which can achieve >99 per cent zinc extraction and more efficient jarosite precipitation to residual iron concentrations of

Jan 1, 1993

By G J. Jameson, A Agarwal

This paper is concerned with the observation and analysis of bubble clusters in a laboratory flotation cell. A device was used in which bubbles were allowed to rise in clean water containing the same frother and collector concentration as in the cell. Bubble clusters were recorded using a high speed camera and analysed using an image analyser. Dodecyl amine was employed as a collector to float silica. The effect of impeller speed on the cluster behaviour was investigated. The results were interpreted in terms of cluster diameter and shape factor. The sizes of the bubbles forming the clusters were also measured and compared to the sizes of the independent bubbles in the cell. It was found that there was an optimum impeller speed in which the cluster diameter was a maximum. Higher agitation and the consequent higher power inputs resulted in cluster break-up while lower shear rates promoted cluster formation.

Jan 1, 2005

By J F. Costa, A Grigorieff

Coal mining reclamation is a worldwide concern. This paper presents a Brazilian example where the economic aspects of reclamation are considered. The basic goal of the study is to transform the reclamation procedures into an economic process by integrating the use of land after reclamation and developing profitable post operations. Some of the activities considered in this case study include: using of the coal pit as a landfill, considering appropriate landfill design and construction; using the area for forest development; and developing grassland, forests of native species and the construction of ponds for fishery. This study will conclude that the mined area is: capable of storing large quantities of waste at a competitive cost and at a low environmental risk; commercial forest development is economically feasible; and the lakes and other reclaimed areas can be integrated into the landscape creating a fresh water supply and an area to raise cattle.

Jan 1, 2005

By F Cappuccitti

A colourimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determinations in a campaign at Kennecott Utah Copper Copperton Concentrator (Rio Tinto). Some observations are described, including: frother (MIBC) concentration evolution down a bank, frother distribution between pulp and froth phases, and loss of frother over time due to adsorption on certain minerals. A possible interference with a fuel oil addition was overcome. MIBC in recycle water was also measured. The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimisation of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimise the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.

Jan 1, 2005

By S Sabanov

Supplementary sampling of particulate mass concentration, the number concentration and the average particle diameter of nanoparticles using a TSI Dust-Trak DRX Aerosol Monitor, Naneos Partector 2 has been conducted. The aim of this study was to evaluate suitability of the instrument for long-term monitoring of diesel particulate matter (DPM) at conditions of polymetallic mines. Sampling was conducted in an area of the active ore heading, requiring the use of a diesel-powered face haul-age loader R1700 and a mine truck Caterpillar AD-45. The sampling was done for 126 minutes at a distance of 30 metres from the mine face. Results of this field work can be used to expand the sampling program to other mines. Expected outcomes of this study are to develop costeffective DPM control strategies, improve mine ventilation, and protect mineworkers’ health.

Oct 12, 2022

By L Brodie-Hally

In the early-1990s, Tad Golosinski, the former the head of mining department at WASM participated in a review mining engineering courses in Australia. The review team asked various industry executives what subjects they thought graduates needed to be taught. Tad made the comment to me that the more senior executives thought that history and ethics were very important. The outcome was that the mining engineering courses were required to contain at least five per cent content dealing in ethics. The course was to be modified to reflect this. Tad thought at the time the students would think that subjects dealing in history and ethics came from retirees and professionals that were over the hill. So let me talk to you today about ethics.

Jan 1, 2002