Search Documents

It is proposed to consider a new access, mining and hoisting system for underground deposits, as an alternative to the commonly used decline or vertical shaft access. The proposed system offers fundamental improvements in gathering of exploration data, reduction of capital expenditure and significant savings in mine operating costs. The cost reductions are achieved through:superior orebody definition by Supersucker winzing on ore prior to the commencement of capital development; considerable reduction of capital development in waste; full capitalisation on all benefits of a raisebored excavation; introduction of rubber tyred skip and rubber tyred Mine Rapid Response Vehicle; introduction of simplified ore handling system and reduction of underground mobile diesel fleet; and introduction of minimum maintenance shaft concept. The system is applicable to deposits ranging from shallow, low dip angle, narrow vein, high-grade to bigger, massive type vertical mineralisations accessed from the surface, preferably from the bottom of an open pit; it is also suitable as a down dip extension of an existing underground mine. The system is highly conducive to mine automation and emerging trend aimed to increase the ratio of mined metal/mineral to mined waste. It offers substantial reduction in diesel exhaust gas emissions to the mine atmosphere.

Jan 1, 2000

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

Mining One (M1) is often challenged with the task of evaluating deposits considering open cut and/or underground (UG) mining methods. In many near surface deposits a combination of both methods results in the optimum economic means of exploitation. As common as it is to have open pit mines eventually develop into underground mines, theory associated with determining the optimum underground/open pit interface location continues to be subject to refinement. With recent developments in underground software packages, the generation of rudimentary underground mining stopes from basic economic inputs is not only fast, it provides a practical underground mining solution. The determination of the open pit/underground interface is not new to Gemcom's Whittle 4X (Whittle). However, its solution has only ever claimed to be indicative, mainly due the rudimentary nature of how Whittle represents any potential underground mining. The efficient generation of the aforementioned underground mining solution has provided mining engineers with a unique opportunity. Underground mining can now be represented within the Whittle environment to allow the open pit/underground mining scenario to be modelled with increased accuracy. Providing Whittle with the ability to now consider mineable underground stopes combined with the consideration of time value of money (discounting), has delivered a solution with higher credibility than ever before.This paper will elaborate on the potential value gains associated with improved accuracies in the modelling of any potential underground mining in the Whittle environment. Furthermore, it will explain the importance of incorporating time value of money in the optimisation process to provide a consistent solution through to pit selection and final analysis.

Dec 6, 2010

The theme of my address to your Institute, indeed its name, is "The Mineral Industry - What Next?" Knowing that I was required to make four appearances, and not wanting to be too repetitious, I wrote a rather long speech of which I will deliver various sections at different places, with a common introduction. Specific areas I have addressed are "Exploration", "New sources of minerals and energy", and "Mining and metallurgy of the future".

Jan 1, 1984

By J Jackson, M F. Young

"Ore is the economic portion of a mineral deposit that can be extracted economically. Hence an ore type is a classification of the ore based on one or more dominant characteristics in order to enable communication between unit operations and/or technical disciplines.In project evaluation, ore types are often defined early based on geological observations by geologists and initial metallurgical testing is based around this classification even though a number of processing options can be under evaluation. However, the geological drivers of performance for each of these processes can be very different and the ore type classification for one process may not be relevant for another. In operations an ore type, as either defined in the project evaluation phase or those that evolve with additional knowledge, is unlikely to provide the knowledge required across all the unit operations. The ore type has a meaning to someone but does not necessarily for all unit operations across the value chain.Geometallurgical or orebody knowledge has evolved through the consideration of multiple processes within the value chain, the improved understanding of variability of process performance within ore types and the effect on the complexity of the mineral extraction processes. Furthermore orebody knowledge has been moving from personal based knowledge and understanding to a more process oriented approach where measurement and spatial and process performance modelling is playing a greater role. Advances in mine planning and scheduling allow for both detailed analysis of the block model and the expected extraction processing attributes across various time scales. This capability of analysing and describing the complexity still requires to be communicated to the various unit operations, which may be beyond the traditional classification of an ore type.The limitations of an ore type and potential alternatives to enable the relevant information to be communicated to the relevant groups are outlined through a number of case examples across the value chain.CITATION:Jackson, J and Young, M F, 2016. Ore Type – Everything to Someone but Nothing to Anyone, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 267–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The phrase "Total-Energy" has, during the past few years, become widely used to describe a wide range of very different operations. However, if accurately described they all have one basic factor in common - energy usage is optimised with the prime mover being powered by gas or oil to generate shaft horsepower and the products of combustion being put to some use. The item which distinguishes a Total Energy system from any other engine or turbine driven project is that orate pains are taken to utilize the waste heat, whether this be in the form of exhaust gases and/or engine jacket ling water. n areas where grid supplies of electricity are readily available, the economics of most projects undoubtedly hinge upon the successful application of waste heat. However, there has been a growing awareness of other benefits, such as reliability of supply, which can be incorporated into the system. In particular these factors sway managements of hospitals and companies with complex computer facilities to examine closely the feasibility of Total Energy, Consequently, in America for example, where many systems have proved themselves the list of applications is wide - shopping centres, apartment blocks, office buildings, airline terminals, universities, schools, motels. And these do not cover the industrial sectors where the range is wider. The total number in North America is now approximately 500 and this to some extent-speaks for itself. In Australia, the real work involved in carrying out feasibility studies for Total Energy is only just beginning. 'in some quarters, the concept is not well received in that it is too new. Therefore, a typical approach is to play safe and wait until some other company has proved its operation "under Australian conditions". This is certainly a realistic approach when considering something revolutionary but as far as Total Energy.is"concerned all the individual components and sometimes combinations, (engines, generators, boilers, air-conditioning units) have been in operation for many years. The only innovation is that they are now all being brought together under one roof. This should not be forgotten when the question "where can I see something like this operating?" is asked.

Jan 1, 1970

By A E Reschke

The high-shear colloidal mixer is generally recognised as the most efficient method of mixing cement based grouts. Only recently however has this technology been applied to the production of cemented rockfill (CRF) for use in underground mines in North America. Traditionally, paddle type mixers have been used to produce the cement based slurries required for the preparation of CRF. While considerable success has been achieved with these mixers, tremendous advantages are attained with the colloidal mixer. The combined effect of the highly efficient mixing action and the ability to mix low water/solids ratios, allows for reductions in the cement content for a given strength requirement. Cement can also be replaced by cheaper fillers such as flyash, resulting in further cost savings. Although large-scale dedicated CRF hatching plants are typical, there is a growing need for mobile plants capable of operating anywhere underground. The compact size and rapid hatching speed of high-shear colloidal mixers has allowed them to be incorporated into skid mounted systems capable of producing and discharging cement based slurries onto rockfill aggregate for the production of CRF. In many cases run-of-mine development waste can be used as CRF aggregate with these slurry plants thereby reducing the cost of waste rock removal. These relatively low cost portable plants have now allowed several mines to economically rccmer isolated pillars and realise positive returns on their investment.

Jan 1, 1998

By D Finn, D Kentwell

Experience has shown that the E-Type multiple indicator kriging (MIK) estimation technique often works well for resource estimation in stockwork mineralisation that contains a mixture of high and low-grade mineralisation types that are difficult or impossible to separate spatially. E-Type MIK, like ordinary kriging (OK) is a smoothing estimator and where data is sparse can result in estimates of grade tonnage curves that do not reflect the true block variability at selective mining unit (SMU) scale. The rank and replace (RR) estimation methodology is designed to reproduce both local block accuracy and true block variability at SMU scale and has shown good results when used with highly skewed unimodal diffusive style mineralisation. This paper examines the use of RR with mosaic style mineralisation typically found in stockworks via a case study using real data from Newcrest’s Telfer West Dome deposit. Resource level estimation results for ordinary kriging (OK), E-Type MIK and RR are compared to close spaced grade control models as the reference reality.Results show that stationarity requirements and declustering can severely impact on the usefulness of the rank and replace technique and that it should only be used where trends are not too strong and data are relatively uniformly spaced. This does not rule out its application to stockwork or mosaic style deposits. However, in this case, the presence of trends and different data densities requires the non-stationary domain to be further broken down into sub domains for the RR technique to be effective.CITATION:Kentwell, D and Finn, D, 2017. Testing new estimation techniques – rank and replace: a stockwork case study, in Proceedings Tenth International Mining Geology Conference 2017, pp 365–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

The region we call the West Coast is acknowledged as one of the richest and most diverse mineral provinces in the world. It's the most rugged part of Tasmania and our island is one of the most rugged parts of Australia, so that speaks for itself. A hostile land of razorback mountains, deep ravines, dangerous rivers, almost impenetrable rainforests and a climate that can change from mild to freezing in a matter of hours.

Jan 1, 1993

By van der Walt TJ, van Deventer JSJ, Reuter MA

Owing to their complexity, many metallurgical processes are difficult to model fundamentally, and as a result more attention has been focused on the use of artificial intelligence techniques to simulate these processes. In this paper recent advances in the use of neural nets to model processes not amenable to conventional methods are discussed. These include the application of a new modelling methodology based on the use of neural nets for the dynamic simulation of metallurgical processes, the use of conventional techniques in conjunction with neural nets to simulate gravity separation circuits, as well as the detection of gross errors in variable measurements by means of a neural net representation of the relation between measurement and constraint residuals.

Jan 1, 1993

The history of mining is rightly proud of its achievements in improving productivity and cost improvements over the years. No matter what measure is used, tonnes per manhour, cost per tonne, etc vast improvements have been made over the last hundred years. In fact over the last ten years in Australian coal mines raw coal output per employee has increased by 60 per cent. When one examines why these improvements have taken place the principal reasons have been technological advancement in mining equipment, excavator and dump truck capacity increases, longwall and continuous miners continually improving in reliability and size. Of course all these improvements are correlated to an increase in capital cost. Even with the above-mentioned advances the pressure for increased performance is as strong as ever. The international mining and mineral-processing sector is currently operating in a recessive market with some traditional commodities, eg gold trading at 20 year lows. During recessive times senior management will demand greater returns on capital employed: the obvious choices being reducing costs or increasing throughput. In addition, head office environments will often place a capital freeze on operational management so the opportunity to take advantage of technological change is not available. The challenge is, therefore, to increase throughput and cut costs without the need for capital. The answer is to optimise the existing labour and plant. If done systematically a result in productivity improvement, in our experience, as high as 45 per cent can be achieved with the average across South East Asia and Australasia being 21 - 23 per cent. The intention of this paper is to present a systematic approach to labour and machine utilisation thereby gaining the greatest possible return on the existing capital base.

Jan 1, 1999

By Daxian Z, Youdi Z, Shucai Y

The Huolinhe surface mine is a very large-scale surface coal mine, located in the north-east area of China with a production rate of 1.2 Mtpa. Its coal haulage system has a large capacity, long transportation line and high degree of automation. The system comprises two crushing plants, many belt conveyors, four surge bunkers, one loading bunker, one coal storage and five end product bunkers. In this paper, the network patterns of semi-continuous systems in surface mines are studied, the reliability calculation methods and a simulation model are established and the software for computing the reliability of a semi-continuous system is worked out. By considering the whole coal haulage system in the Huolinhe surface mine, the authors developed the system reliability-numerical simulation method. The steps and the computing results of this method are described in detail. Through the calculation, we can master the present situation of system reliability and the main factors impairing system reliability, expose the system weak links, put forward the ways of enhancing system reliability and furnish the basis for improving the system and equipment. The way of increasing capacity and methods of enhancing system reliability are further raised.

Jan 1, 1995

By S DeKruijff

The Mount Isa Mines Copper Mine in Mount Isa started producing copper in 1966. The Copper Mine gradually increased production rates to nearly six million tonnes per year. Over the last three years the mine has been in a gradual ramp down due to the reduction of primary ore sources and head grade. The majority of ore sources are predominantly in pillar retreat sequences bounded by multiple fill masses. There also a substantial lower grade resource delineated to the south of the main orebody. These remaining ore sources present significant engineering challenges to obtain a safe and cost-effective extraction. Stope designs have become increasingly complex and require additional engineering and operations input and analysis. This paper describes the major planning and operational challenges and issues associated with the stope design and extraction of an orebody in the later stages of mine life.

Jan 1, 2000

By G Lane

This paper discusses the factors that contribute to the cost effective design of a concentrator. Concentrator design and layout outcomes are functions of the team (engineer’s and owner’s) participating in each particular project. The benchmark for relatively modest projects was set in the 1980s and 1990s during the ‘gold boom’ when numerous cost effective plants were designed and constructed on a lump sum basis in a very competitive market. A number of factors contribute to lack of transference of the lessons learnt in gold plant design to concentrator design including established paradigms in the design and layout of concentrators, lack of experience in cost effective design, operator’s preferences for flowsheet and layout and simple lack of appreciation of the impact of plant footprint on materials quantities and resultant capital costs.Experiences with recent copper concentrator projects (both small and large) are used as case studies.

Aug 8, 2011

By M Campbell, A Jeffcoate, J-C Vannay, B Perriaux

Phyllite waste rock at the Simandou Pic de Fon and Oueleba Iron Ore deposits (Guinea, West Africa) variably weather to form clay-rich rocks. This weathering modifies the mineralogical, geochemical and mechanical properties of the phyllites. Final pit walls will largely be formed in phyllite, so it is critical that the slope design takes account of the distribution and variability of weathering within this material. Phyllite intact material strength has been correlated with geochemistry (ie mineralogy) facilitating the establishment of domains of intact rock strength (IRS). In order to calibrate this geochemically-based strength model, core from diamond drilling (DD), comprising a variety of phyllite material types (from soft clay to moderate strength rock), was geotechnically logged to assess intact strength; further validation was achieved by uniaxial compression (UCS) testing and point load tests (PLT). The correlation between geochemistry and strength offers a potentially powerful tool for differentiating basic mechanical properties of the rock mass, especially at Simandou where a significant proportion of the resource drilling is done by reverse circulation (RC). Unlike DD, reliable measurements of material strength from RC samples can prove difficult, especially in clay-rich material. Therefore, gaining information from routine geochemical assay results, independent of the sampleÆs physical integrity, is a valuable and cost-effective source of reliable empirical data. Data acquired using this approach provides an opportunity to develop strength domains, which are integrated into mine planning block models. In combination with other geotechnical characteristics, this can be a valuable input to the development of geotechnical models. This technique has allowed spatially representative rock strength data to be derived and offers the potential for optimising pit slope angles in areas where hitherto conservative design criteria had been assumed.CITATION:Jeffcoate, A, Campbell, M, Vannay, J-C and Perriaux, B, 2013. Modelling intact rock strength of clay-rich rocks with geochemistry at the Simandou iron ore deposit, Guinea, West Africa, in Proceedings Iron Ore 2013 , pp 193-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M K. Singh

Mining is nothing but an art - besides being a science - of extracting valuable minerals from the womb of the mother earth. In this gigantic task, a large number of machinery and equipment are employed judiciously. Wire ropes play a vital role in lifting or hoisting men and materials under hostile/adverse working conditions and constitute a major item of investment on machinery/equipment. The economy of using a wire rope is a concern for engineers, users and the planners. The economic use of wire ropes for mining purposes largely depends on the following factors;Mechanical design considerations - which include tensile strength of wires, elasticity, resistance to abrasion and crushing, fatigue values, static and dynamic loads on wire ropes, factor of safety, fleet angle, etc. Metallurgical consideration - Composition and heat treatment of wire materials, defects like inclusions and voids, surface quality factor, lubrications, micro structural parameters. Operational consideration - Seizing and cutting of rope, storage, care and maintenance, cutting back, etc. Environmental consideration - Temperature and humidity, pit condition, dust, corrosive atmosphere, etc. In the present paper, an attempt will be made to suggest steps for achieving optimum economy while using the wire ropes for extraction of precious minerals and coal keeping in view the points noted earlier. Once technical viability is established, economy is the ultimate consideration for an industry for safe hoisting of men and material.

Jan 1, 2000

By J Chan, T Baumgartl, A Plante, C Peltre, P D. Erskine

Mine soils are often organic matter and carbon poor due to disturbance, topsoil stockpiling and mixing with spoil. They present an opportunity to observe the accumulation of soil carbon arising from rehabilitation or ‘green carbon’ through organic matter inputs and may be considered for carbon credits. Soil carbon is known to improve multiple soil characteristics and is viewed as an indicator of soil health.When attempting to estimate soil carbon levels in the Australian coal mining regions, both coal and black carbon (BC) need to be quantified. Coalmine soils contain coal particles that are difficult to distinguish from organic matter using standard carbon analyses. BC, a material arising from the incomplete combustion of organic matter and fossil fuels, displays some similar characteristics to coal and is ubiquitous in Australian soils due to bushfires. The presence of coal and BC complicate the determination of green carbon levels in mine soils.A method to quantify coal and BC in mine soils from the Bowen Basin using thermal analysis and multivariate curve resolution is presented. By determining BC and coal contributions it is then possible to calculate green carbon levels in rehabilitated mine soils. Calculated green carbon levels are compared with bulk density as soil quality indicators.CITATION:Chan, J, Baumgartl, T, Erskine, P D, Peltre, C and Plante, A, 2014. Distinguishing carbon fractions in coalmine rehabilitated soils, in Proceedings Life-of-Mine 2014 , pp 491–498 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By S Dykes, R J. McCarthy, B Klein

There is growing interest in the mining industry on the application of ore sorting. While many are familiar with particle sorting, including the limitations that technology presents (e.g. throughput), bulk sorting, with its higher throughput potential, is less understood. Despite the potential to sort at higher throughputs, few operations have adopted bulk sorting processes, certainly not at large scale. It is suggested that the inability to reliably predict outcomes from bulk sorting may be limiting its adoption in mining projects. Consequently, an evaluation approach for bulk ore sorting has been developed such that mass pulls and grade upgrades can be predicted in the context of a mining study. The approach allows for evaluation of drill core assays and application of the consequently derived heterogeneity relationships to the block model for estimation of sorting outcomes. These processes were applied to conveyor-based bulk sorting for the CuMo project in Idaho, USA and are described in this paper.

Nov 10, 2020

Reliability is not only important in coal mine planning, production and control. Reliability is also most important, and indeed is fundamental, to successful coal exporting.Coal preparation, blending, distribution, marketing and utilisation are areas of the coal industry in which reliability can be critical to coal exporting. Major elements of reliability which impact on coal exporting include coal quality, supply performance, -coal ownership changes, governmental regulations and policies, market reputations and differences in export markets.

Jan 1, 1991

By V A. Maltsev, V I. Panin

The question of prediction and prevention of dynamic events û rock bursts (RB), tectonic rock burst (TRB) and mining-induced earthquakes (MIE), induced by large-scale mining, are discussed. The mine itself and the host geological environment are taken as a natural-technical system (NTS) whose evolution is characterised by alteration of the adaptation-bifurcation (catastrophes) periods. So, to predict TRB-MIE means to predict the limiting NTS states that are determined from the NTS geological monitoring data, and to prevent the said events means to control the processes of rock deformation and failure within the critical zone. The study considers particular examples of how TRB-MIE-events are predicted and prevented in apatite mines, Kola peninsula, Russia.

Jan 1, 2000