Search Documents

The Golden Cross mine is situated in a sensitive environmental setting on the North Island of New Zealand, about 150 kilometres south-east of Auckland and about 8 kilometres NW of Waihi. The mine is situated in dipping topography, with volcanic ashes making up soils, fault zones running through the area, and rainfall of about 3 m per year on average. Water management is the most demanding environmental challenge on site, and a comprehensive programme has been put in place to address tailings deposition, long term tailings storage, and water treatment during and after operations.   The tailings impoundment is built with an underdrainage system that collects groundwaters and waters that seep through the impoundment. The embankment and impoundment are both built to withstand the Maximum Credible Earthquake and the Probable Maximum Flood. Tailings are treated to remove cyanide and to decrease metal solubility to reduce long term risk to water quality after mining. A state-of-the-art water treatment plant is utilised to treat water from the underdrainage system and water decanted from the top of the tailings pond and stormwaters to remove residual cyanide and metals to extremely high standards with a great deal of reliability and at reasonable cost. Closure of the facility addresses long term post mining water quality issues, and rehabilitation of the area with wildlife habitat as a priority.

Jan 1, 1995

By W L. Daniels, C Stilson, C Zimmerman

Mineral sands mining for ilmenite, rutile and zircon has disturbed over 1000 ha of prime farmland in Virginia (USA) since 1997 and additional areas are likely to be disturbed in Virginia and North Carolina (USA) over the next 15 years. Full-scale mining operations at the Old Hickory Project in Virginia were initiated in 1997 by Iluka Resources Inc. and restoration protocols have continued to evolve in response to a variety of economic, technical and social issues. Early on, the return of these lands to agricultural row-crop production was complicated by vertical stratification of tails + slimes and lateral variability in soil physical conditions in the reclaimed pits and by limited topsoil return. Virginia Tech and Iluka have worked cooperatively with all stakeholders for over 20 years to review the pre-existing research base, conduct new and innovative site-specific research and thereby provide reasonable expectations of post-mining soil productivity levels. In 2004, Virginia Tech, Iluka Resources and a local leaseholder (Carraway-Winn family) agreed to jointly manage a 45 ha research demonstration farm where the long-term effects of alternative soil reconstruction practices are being rigorously monitored for both row crops (corn and wheat) and forage production. All mined land crop yields are also compared to an adjacent undisturbed exceptional quality prime farmland soil. Row crop yields between 2005 and 2010 were significantly above county average yields (regulatory target level) and approximately 75 - 80 per cent of undisturbed adjacent prime farmlands. The state regulatory authority has recently relaxed its position on the necessity of topsoil return versus use of topsoil substitutes based on appropriate on-site research results and the ability of the reclaimed soils to meet comparative local county crop yield targets. This cooperative effort allows all clientele groups to objectively assess the post-mining productivity of these mined lands while providing an invaluable educational opportunity for the mining industry. CITATION:Daniels, W L, Stilson, C and Zimmerman, C, 2012. Development of effective rehabilitation protocols for mineral sands mining in Virginia, USA, in Proceedings Life-of-Mine 2012 , pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By N Rivera, A Music, C Cisternas

In an underground mine operated with panel caving and subjected to high stresses, geotechnical events such as collapses or rock bursts are fairly recurrent. Both situations can involve risks for people, considerable production losses and increasing operational costs.This paper discusses an operational methodology for the recovery of the undercutting front carried out at El Teniente mine, which uses panel cave mining with post-undercutting, after the occurrence of severe damage due to a seismic cluster. The main objective of the recovery of the undercutting front is to prevent the spread of the collapse to the production level, risking the operational continuity. The methodology is the result of repairs that were carried out in the year 2014 at the North Reserves sector from El Teniente mine. Its characteristics are an undercutting front of almost 1000 m long, with the presence of relevant structures and faults, high stresses and high seismic activity.The practical implementation of the proposed methodology was successful since it prevented the spread of the damage, completely recovered the undercutting front and avoided production losses during the execution of the repairs. Also, considering the origin of the damage and the operations associated to the subsequent recovery of the undercutting front, in this paper we discuss the main control variables to be measured. These variables should allow any operator and short-term planner to take action in mines operated with conventional panel caving in a complex geotechnical environment.CITATION:Rivera, N, Music, A and Cisternas, C, 2016. Recovery of the undercutting front in a mine with conventional panel caving – case study at North Reserves sector, El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 713–722 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

PIP is regularly engaged in businesses where Greenfield Capital Projects are under- delivering on the expected business case. In most of these projects, we can identify that rigorous review has been carried out on the design and financial cost elements and substantial reporting is maintained to Boards on progress versus plan of project completion and cost. However, in all sites of this nature that we have worked at, the planning, design and execution of the operational elements or æwiringÆ of the organisation have fallen short and resulted in significant extra cost or opportunity cost (lost tonnage or quality) during start-up. When compared to the amount of planning and resources that have been poured into the capital side, the ledger on the æwiringÆ side is typically fairly sparse. This presentation outlines the importance of running a disciplined, rigorous process to prepare the human and wiring side of a start-up to ensure rapid start-ups and put the site on the pathway to high performance. It gives an outline of the rigorous process PIP has used with projects to ensure excellent start-ups.

Jan 1, 2006

By A D. Strand

The Coeur dÆAlene mining district in northern Idaho, USA is the second largest producer of silver in the world. The Proterozoic Revett Formation hosts most of the mesothermal Ag-Pb-Zn vein ore in the district; it consists of informally designated lower, middle, and upper members. All three members show up to an order of magnitude of southward thickening across the regionally significant Osburn fault. Changes in thickness of the Revett Formation across the Osburn fault reflect a major, down-to-the-south, crustal-scale fault that:was active during sedimentation, was periodically reactivated during the structural and metallogenic history of the district, and likely provided first-order control over regional fluid flow during mineralization events. Where vein structures intersect favourable strata, they produce rich ore; where vein structures cross unfavourable strata, they are poorly mineralised or barren. The most favourable host rock in the district is quartzite, which accounts for the large production from the quartzite-rich Revett Formation.The district has five main types of hydrothermal alteration:feldspar destruction, hydrothermal bleaching, carbonatisation, sulfidation, and silicification. Feldspar destruction is the most extensive and pervasive type of alteration, involving the district-wide absence of feldspar from Belt Supergroup rocks. Hydrothermal bleaching results from the destruction of hematite; it forms alteration envelopes that extend for tens to hundreds of metres into the wall rocks around many of the mineralised veins. Siderite alteration is most diagnostic of mineralisation, forming alteration envelopes that extend for tens to hundreds of metres into the wall rocks around all mineralised veins. Fine-grained arsenopyrite and/or fine-grained pyrite commonly form alteration zones adjacent to high-grade ore shoots that extend for metres to tens of metres into the wall rocks. Widespread silicification is most easily recognised by the presence of numerous quartz veins.

Jan 1, 2002

By R Hughes

"Spring Creek Mine uses high pressure water to extract the thick Main seam in the Upper Rewanuicoal measures. The extraction method results in the creation of large voids which collapsespontaneously. This can result in the displacement of large volumes of methane, which may create a signifi cant hazard if not correctly managed. A system of automatic dilution doors is employed to mitigate this risk. This paper describes the evolution of the system and gives some examples of its eff ectiveness."

Jun 1, 2012

By J Jones

A common problem in the mining industry is that company exploration groups operate in relative isolation to the rest of the company; resulting in poor knowledge transfer (Qureshi and Briggs, 2006) and often priority conflicts with mine geology, operations and project departments. In recognition of this problem, Newcrest created a Minerals Division responsible for stewardship and governance of mineral assets across the value chain from reconnaissance to rehabilitation. It was recognised at an early stage that effective collaboration both internally and externally would be required to improve decision making, deliver faster cycle times and improve governance.Collaboration in companies is generally associated with the introduction of new IT functions. However, modern IT-based collaboration systems and practices are relatively simplistic compared to the long-standing practices associated with collaboration and knowledge management in science and engineering disciplines such as geology and mining.The authors of this paper have started a trial of a 12-point plan for effective collaboration, which recognises that significant efficiencies can be gained and barriers to future success removed if more effective collaboration can be achieved between science and engineering divisions in a company along with external professionals and with the collective intelligence (Tapscott and Williams, 2006) of the outside world. To meet growth aspirations some companies, like Newcrest Mining Ltd, are adopting this comprehensive, step change approach by moving from a closed model the isolates mine geologists to an open and collaborative model that uses IT visualisation systems strategically. The paper describes how an open model provides people with the right work environment and the right information at the right time, which will help individuals and workgroups to work more collaboratively day-to-day. The aim is to achieve speed, focus and mitigate risk through an environment where everyone and anyone can contribute effectively (Cisco, 2008).

Aug 22, 2011

By L D. Munro, S A. Jackson

This paper provides a logical approach to developing a TSF design concept through: • Identifying key properties of tailings and containment structures; • Reviewing underlying principles for effective operation; • Showing how these apply to select an appropriate TMS; and • Demonstrating how to align the TMS to site-specific constraints and TSF design. This approach follows a path of rigorous data analysis independent of discharge parameters (whether low-density slurry, paste or cake disposal) to select the most cost-effective and sustainable approach for any given material or site.

Jul 1, 2021

By J P. Sykes, T C. McCuaig, J E. Vann

Resources added to the global metal inventory through exploration over the past 15 years have been generally of poor quality (declining grades, recoveries and lack of acceptable financial return). Similarly, companies opting for an acquisitions-based strategy have had to pick from a group of poorer quality resources left from previous exploration booms, and will struggle to deliver this metal to market economically. Increasing difficulty in obtaining sufficient social and community acceptance of mining projects and potentially an energy-constrained future may exacerbate this problem, redefining what is considered ‘ore’. There will need to be more focus on deposit quality, defined as sustainable margin in the future business environment.Traditionally there has been a lack of translation of ‘mineralisation quality’ back to mineral project design and mineral exploration. This disconnect is due to two main factors: the first is technical – inherent deposit variability; and the second is organisational and socio-psychological –the mindset of explorers and project managers themselves.There are four elements to value realisation for a mineral deposit: (1) social licence to operate; (2) geological factors (depth, geometry, water and geotechnical, and geometallurgy – influenced by texture, mineralogy, chemistry and grades); (3) financial engineering (capex, opex, future commodity prices, future energy prices), and (4) operating factors (production rate, recovery, energy consumption). These elements are strongly interdependent, and geology underpins and drives linkages between them. A quality deposit addresses all of these elements and thus can be developed in a time frame that allows acceptable returns to the owners of the invested capital.Geological drivers of the above elements can be measured and mapped throughout a deposit. Moreover, when viewed in the context of mineral systems, a predictive understanding of the common causative processes of quality (despite deposit-scale variability) is emerging, and with it the ability to target quality of mineralisation, not just quantity of mineralisation.The second factor is a ‘heuristic software problem’. Current lines of education (and consequently organisational and professional structures) are discipline-based, producing ‘silos’ that do not speak each other’s language and work with different ‘mental models’. People who effectively recognise systemic links between these silos are called ‘boundary spanners’, of which we propose two distinct types: outside-insiders and inside-outsiders. Outside-insiders are people who are within a community, but recognise advances in outside fields and effectively integrate them into the community. Inside-outsiders start outside of a community, and successfully bring new ideas into it. Common traits in boundary spanners are: they seek exposure to (and embrace) key ideas that are outside of the framework of their own specialisation; they have high mental processing ability (MPA) – the ability to connect systems that are currently not perceived to be connected; and they introduce ideas from outside a field into a new context in a way that re-frames the field.The challenge is to identify and nurture potential boundary spanners that can build critical links, in particular between the (largely geoscientific) mineral exploration mindset and the (largely non-geoscientific) project development mindset. Critical linkages to be built are between mineral system science, targeting science, and whole of value chain modelling.CITATION:McCuaig, T C, Vann, J E and Sykes, J P, 2014. Mines versus mineralisation – deposit quality, mineral exploration strategy and the role of ‘boundary spanners’, in Proceedings Ninth International Mining Geology Conference 2014 , pp 33–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By H Jones

Closure cost estimates may be generated at any stage of a mining operationÆs life; commencing with the initial prefeasibility studies and continuing through to the final decommissioning cost estimates. However, not all mine closure cost estimates are necessarily the same. Cost estimates will vary depending on the purpose for which they are prepared, the organisations requiring or undertaking the estimate and the stage of the mining operation. Different organisations can legitimately arrive at disparate cost estimates for closing the same mine because the organisations have different reasons for requiring the estimates. Another, equally valid, reason for potentially wide variations in cost estimates by different organisations on the same mine site is the different definitions of æclosure costsÆ used by different estimators. This paper considers the different approaches by different organisations including operating companies, government authorities and financial organisations and uses a hypothetical example based on practical experience to illustrate some of these differences in estimation methods.The paper suggest that a more consistent approach to closure cost estimating in the Australian mining industry would assist mining companies, governments, the accounting industry and the broader community to better understand this complex component of mine planning. One possible approach to closure cost estimating is briefly outlined.CITATION:Jones, H, 2012. Closure cost estimation - All things to all men?, in Proceedings International Mine Management 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By Crawford M

During the initial development of Mount Isa Mines power was supplied from a temporary power plant situated near the Man & Supply Shaft. The main power plant was placed in service early in 1931 and then comprised two Babcock and Willcox boilers, fired by pulverised fuel, and two British General Electric Company's turbo-alternators of 5,000 kW. each. Both plants have been described by A. F. McAskill in the Journal of the Institution of Engineers, Australia.From 1931 power demand progressively increased due to greater production, further mine development in the harder sulphides increased pumping for mine drainage and additions to mill and smelter until, by 1935, the plant was inadequate for further output commensurate with a reasonable safety margin.Coincident with the added power demand, operating conditions involved a fuel problem which could not have been anticipated. The ash content of the fuel supplied gradually increased from 13% to 16-5%, while the melting point of the ash decreased with higher pyrite content.Temperature conditions in the furnace required careful control to cope with ash formation and slag accretions.Consequently brickwork, excessively stressed on water walls, was constantly under repair, and required suspension periods of 50% of operating time for cleaning and overhaul.Load conditions varied continually, therefore the high heat liberations in the furnace, necessary to accommodate peaks in fluctuating output, resulted in ash fusion.

Jan 1, 1939

By L Yang, L Chen, E Hu, D Tang

Online monitoring of particles cumulative percent passing (PCPP) for a target size at hydrocyclone overflow, compared with traditional offline methods, provides PCPP feedback in real time, and is advantageous in enabling energy-efficient comminution, increasing downstream flotation efficiency, and improving upstream resource knowledge. However, existing online approaches are generally costly and bespoke, and some are sensitive to operational changes. Therefore, this study proposes a new low-cost alternative based on accelerometer measurement for online PCPP monitoring in the overflow of hydrocyclones and provides a preliminary experimental investigation under dry condition. The proposed method uses a sensing probe inserted into the overflow pipe of a hydrocyclone to receive particle impact from the incoming slurry, with accelerometers attached to the probe and mounting frame outside the pipe for particle-probe impact detection. As a preliminary investigation before studying particle-probe impact events in slurry, tests under dry condition without fluids were conducted using dry sand particles in free fall from a fixed height. Accelerometer measurements are analysed in both time and frequency domains through root-mean-square (RMS) and fast Fourier transform (FFT). Results show that accelerometer measurements are useful in estimating mass flow rates, which are correlated to the accelerometer output amplitude RMS values in time domain, in a non-linear mapping. Different particle size classes can be identified by examining the accelerometer output amplitude at a known mass flow rate. Different particle size classes feature their distinct signature frequencies (SFs) that can be examined via FFT and the SF is found to be independent of the mass flow rate. The results imply that any PCPP changes can be detected by the change in the accelerometer output amplitude as well as a shift in SF, which demonstrates the effectiveness of using accelerometers to gauge changes in PCPP. Based on the current findings in dry condition, future work will investigate particle-probe impact events in slurry.

Aug 24, 2022

By A N. Danoucaras, S E. Goater, D Hearne, A M. Bansuan

It is globally recognised that existing and emerging mining activities should be conducted in a æsustainableÆ manner for the entire life of mine. Many companies annually publish corporate sustainability reports to demonstrate their actions in accordance with international expectations. This concept of sustainable mining practices also applies to mine water management, with influences often extending beyond site operations, affecting surrounding catchments and community users. This paper explores differences in conceptual and operational terms of æsustainableÆ mine water management within the Philippines. Outcomes of a review of corporate sustainability reports, governance documentation, research programs, and stakeholder knowledge acquired through action-research workshops are presented. The paper aims to inform and support future capacity building exercises delivered by the International Mining for Development Centre (IM4DC), with outcomes tailored to government officials and policy makers of developing countries. The project is funded by IM4DC, which is working with AusAID to identify needs and develop capacity with regard to mining for development; specifically, issues pertaining to governance and regulation, social and environmental sustainability, and operational effectiveness in developing countries.CITATION:Bansuan, A M, Goater, S E, Danoucaras, A N and Hearne, D, 2012. Integrated sustainable water management in mining for development in the Philippines, in Proceedings International Mine Management 2012, pp 205-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By A Jewbali, L Allen

At Newmont Corporation drill hole spacing studies are done to support the business in understanding the cost of collecting additional information (with a specific focus on drill hole sampling density) versus the value of additional drilling in terms of resource risk reduction. For the last 20 years drill hole spacing studies have been executed in an effort to answer the following question: What spacing should the deposit be drilled at to achieve a certain level of resource confidence so that when mining occurs the resource model delivers as predicted ie what is the optimal sampling density? The optimal sampling density supports a resource model that provides a sound foundation for mine planning purposes and resource/reserve reporting. At Newmont Corporation drill hole spacing studies are now a requisite for understanding drill data density needs for new deposits and near mine expansions. This paper details the evolution of drill hole spacing studies at Newmont Corporation in terms of methodology and usage.

May 24, 2023

By D Brown, K Markovic, Z Tabor

From ancient times to the modern world, the mining industry has played a pivotal role in shaping the society that we live in today. It remains an integral part of everyday life and is a catalyst for both technological and economic growth. With finite resources on Earth, and growing pressures surrounding climate change and the environment, space mining opportunities have become of increasing interest. Recent discoveries have shown celestial bodies including the Moon and surrounding asteroids, contain an abundance of critical minerals, as well as resources necessary to sustain human life. These discoveries coupled with a transition into the digital and autonomous age, offer an innovative solution to solving some of the mining challenges currently being faced on Earth. Similarly, they also offer a pathway to enabling deep space exploration and off Earth exploratory missions. However, like with mining operations on Earth, space remains and immensely challenging and complex operational environment. The inhospitable nature of space poses new challenges, including communication barriers, lunar dust, cosmic radiation, and gravity. The challenges and risks are not just technological, as Environmental, Social, and Governance (ESG) factors must also be considered to prevent unintended consequences and hazards. Furthermore, future workforce, law, financial, and security systems must evolve to enable space mining to take place. These are all known aspects to begin with, but as the complexity of the space grows it becomes apparent that a holistic approach to assess and manage these factors will be required.

Sep 1, 2024

By J J. Cilliers, K Hadler

Froth structure and stability are known to play important roles in determining mineral flotation recovery and selectivity. However, measuring froth stability in a consistent manner remains a significant challenge, especially at an industrial scale. Following preliminary tests on a copper concentration plant, a quantitative dynamic stability measure is investigated in this study in order to extend the results over a wider range of conditions and on a different orebody. The technique is based on the Bikerman foam test and uses a non-overflowing froth column to quantify froth stability. Experiments were carried out using an automated version of the froth stability column under different operating conditions. Air flowrate was the key operating variable. Tests were reproduced on a single flotation cell of a Platinum Group Metals concentrator. The froth stability factor, , was measured for each operating condition, and compared with the air recovery in the cell, , which was measured using image analysis. The froth stability column results gave the same trends as image analysis. In particular the froth stability factor was found to be linearly related to the actual fraction of air overflowing the cell. The metallurgical results clearly indicated that changes in air flowrate result in variations in flotation performance that can be attributed to changes in froth stability. The results showed that high froth stability conditions occur at intermediate air flowrates, and result in improved flotation performance. It is found that the froth stability column is a simple, cost-effective and reliable method for quantifying froth stability, and for indicating changes in flotation performance.

Jan 1, 2005

This paper presents an overview of a program PC-BC developed for application to the design and evaluation of block cave operations. Conventional mine planning software tools are not well suited to the evaluation of this type of deposit. The paper looks at the modelling approach as applied to a block cave mining project. The following steps are described:Initial preparation of data including block models, draw point footprint geometry and draw cone geometry. Computation of individual draw point reserves. Procedure for modelling of vertical mixing of material within each draw point and subsequent determination of the best height of draw for each draw point based upon an economic cut-off value. Smoothing of draw heights amongst neighbouring draw points to produce a realistic draw envelope. Mineable reserves within the envelope are then computed. Tools for preparation and evaluation of various production schedules. This includes definition of draw rates, and rates for commissioning new draw points. In an operating mine, the capture and analysis of daily draw tonnages is important. How PC-BC accommodates this is described as well as the processes for depleting the draw column reserves. In the 12 years since the program was first developed, it has been used on a number of projects for feasibility studies and operating mines. Some practical examples of the use of the program in these projects are presented. Finally, some commentary on the sensitivity of various parameters is presented. Particular emphasis is placed on the overall footprint design.

Jan 1, 2000

By L Sandery, S Light

Within 22 months of commencing decline development, the Prominent Hill Ankata Underground Project achieved its full production rate of 1.2 Mt/a.In 2010 construction of the Ankata Underground Project was approved. Decline development commenced in November 2010 and the turnout for the first sublevel was reached by August 2011. The first stoping ore was produced in the first quarter of 2012 and production was successfully ramped up to full production during the third quarter of 2012.Diamond drilling commenced in October 2011 and was conducted concurrently with the underground development. This presented challenges as mining and production targets had to be balanced with underground exploration activities. To achieve production on schedule, without adversely affecting the diamond drilling program and future development, meticulous and adaptive planning techniques were required. This included involvement from engineers, geologists, underground operators and underground diamond drillers.The granularity of these planning techniques allowed the management and prioritisation of development and diamond drilling down to an almost hourly basis. A constant flow of information from drill assay results was fed back into the planning systems. This resulted in a constantly evolving mine plan as the orebody was further refined. High priority areas were identified and targeted to allow continued development and a successful rapid ramp up to full production.CITATION:Sandery, L and Light, S, 2014. Managing the diamond drilling interactions in commissioning the Ankata underground mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 75–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J Joughin, D Kyan, L Rollin

In line with the 2015 Paris Agreement and corresponding climate disclosure requirements, many mining companies have publicly disclosed that they are developing and/or implementing ambitious decarbonisation strategies. Sometimes these strategies can be linked to the development of community programs and/or the creation of a positive legacy post-closure. Renewable power is key to most decarbonisation strategies – some mines will get this from external sources and others will establish on-site power generation and storage facilities. A range of options are available to develop renewable power generation (eg solar panel, wind farm, hydropower) and energy storage (eg battery, hydrogen, pumped hydroelectricity). Land access, impact assessments, planning and environmental approvals are required to establish new facilities. Host communities are more likely to be in favour of, or at least will accommodate, new power supply developments if these are planned with a benefit to the communities. Transitioning to renewables raises new challenges. Among these are high upfront costs and access to capital, energy demand variability, supply intermittency and variability, storage limitations, grid stability and reliability, transmission and distribution infrastructure constraints. Compounding these challenges are issues such as infrastructure resilience to extreme weather events (eg heat, wind), land use and access, lengthy permitting processes, community perceptions, skilled labour requirements, and meeting mine closure objectives. Renewable energy sources provide a more decentralised source of energy that reduces reliance on imported fuels, thereby increasing energy security and lowering production costs. On the contrary, implementing renewable energy could lead to potential negative impacts such as visual perception from the community, competitive land usage, electricity price raises due to upgrading infrastructure and the use of electricity storage capacities. As part of the definition of an environmental and social management plan, participative stakeholder engagement is required to identify benefits to the communities. For example, among the recognised benefits of developing solar panels (increase job opportunities, reduce soil erosion), various technologies have been experimented globally for the last ten years and are emerging due to their proven community benefits. Key findings to enhance those benefits can range from the development of innovative practices such as ‘agri-/aqua-voltaic’, ‘solar grazing’ to optimise land usage and stimulate the local economy (Table 1), to the implementation of technologies providing services to communities such as mobile water desalination plants or ‘smart grid’ systems to minimise energy clipping during peak-load of oversized renewable energy facilities (Table 2). While developing those synergies, careful management is required to avoid creating superfluous energy service needs from community programs. Energy sufficiency should remain a key principle according to the sufficiency, efficiency and renewable framework of the Intergovernmental Panel on Climate Change. Darby and Fawcett (2018) define energy sufficiency has ‘a state in which people’s basic needs for energy services are met equitably and ecological limits are respected’. Sufficiency tackles the causes of the environmental impacts of human activities by avoiding the demand for energy and materials over the life cycle of buildings and goods. Efficiency tackles the symptoms of the environmental impacts of human activities by improving energy and material intensities. The third pillar, renewables, tackles the consequences of the environmental impacts of human activities by reducing the carbon intensity of energy supply (Cabeza et al, 2022). Life of Mine Conference 2023 | Brisbane, Australia | 2–4 August 2023 34 This paper provides project developers, decision-makers and regulatory authorities with ideas on synergies between renewable energy options and community development programs. These can be considered to enhance stakeholders’ support for implementation of decarbonisation strategies.

Aug 2, 2023

By A Kite

Frontline leaders play a critical role in the safe and productive operations of Australia’s mining, resources and heavy industries. These leaders set the workplace culture, especially during night shifts and weekends, by providing team direction and encouragement, providing access to resources, fulfilling statutory requirements, enacting and reinforcing risk management systems, setting the standards on shift and acting as the primary conduit of communications between senior leaders and team members.

May 5, 2022