Search Documents

By G B. Smith

Barrick (Australia Pacific) Limited initiated a trial of Caterpillar’s Minegem autonomous loader technology in 2009 at the Kanowna Belle mine in Kalgoorlie. Autonomous loader technology offers the potential to improve loader productivity, reduce operating costs and improve safety through removing personnel from the mine operating environment. This paper discusses the implementation of the technology at the mine site, the data collected during the trial and quantifies the benefits of using automated loader technology in comparison with teleremote loader operation. The lessons learned from the trial and work planned for the future in respect of this technology is also discussed.

Mar 21, 2011

By B T. Qin, C Zhu, Y W. Jia, Y Lu, F L. Li, Q L. Shi

Air leakage through rock fractures in coal mining is a major cause of coal spontaneous combustion. In order to overcome the deficiency of the existing fire control technology and prevent coal spontaneous combustion by isolating coal from oxygen, the article proposes a novel technology of inorganic solidified foam (ISF) with high expansion to fill fractures effectively. ISF consists of fly ash, cement, setting accelerator, redispersible polymer powder, water and aqueous foam. For preparing homogeneous and stable ISF, a preparation system with a pore type foam generator, a mixer device installed with a hollow shaft and helical blades, air compressor, slush pump and monitoring instruments was developed, and the working principles of key devices were elucidated. Based on a series of experiments on the different ratios of each component material and technological parameters of the preparation system, ISF with a foam expansion ratio of 8~10 and dry density of 250–400 kg/m3 was prepared. The relationship between elastic compressive strength, modulus of elasticity and density was summarised. Based on the injection experiment for fracture of loose coal pile with high temperature, the characteristics of sealing air leakage, compressive strength, thermal insulation, flow and cooling of ISF in the fresh state were investigated, indicating that ISF can effectively cut off the air leakage and cover the coal sample to reduce the temperature in the earlier stage, and ISF can remain stable and not crack. The ISF was applied to Luwa coalmine to seal small coal pillar pressure fractures and loose coal fractures in goaf. After press-casting the ISF in Luwa coalmine, the pressure-difference of inner-outer increased, meaning the effect of external conditions on the pressure-difference decreased, showing that it could plug the air leakage effectively.CITATION:Qin, B T, Shi, Q L, Lu, Y, Zhu, C, Li, F L and Jia, Y W, 2015. The novel technology of inorganic solidified foam with high expansion for preventing coal spontaneous combustion, in Proceedings The Australian Mine Ventilation Conference, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The complete life cycle of a production facility has many phases requiring many different skills and many different personalities. It is not unlike the life cycle of a person and many parallels can be drawn from it. I leave some of these analogous situations to your fertile minds. The author, having worked in operations, plant design, plant commissioning, marketing and many other interesting situations through the industry has drawn from this experience and examples given by many associates in the industry.The phases seen are as follows: Concept Studies û someone has a bright idea of how to make a dollar. Scope Studies û what possible processes/options that could make a dollar. Prefeasibility Study û the æviableÆ scope options are studied to develop feasible options. Feasibility study û defines the concepts that should be designed to make a viable project thus enabling financing and project commitment to be made. Detailed Design û an intermediate step that consolidates the inputs to give a robust plant that can be constructed.Construction û people can see what they thought was going to occur and start to understand the plant. Commissioning û the hand-over of æownershipÆ from the conceiverÆs to the operators. Operations û the ætoyÆ has become reality and money must be made. De-commissioning û the plant has seen out the useful life of the ore deposit, it now goes through a further process required by society.Across these phases of plant design run several countervailing management requirements that can influence the outcome of the plant design. Some of the management rigours that have to be applied to the various phases are as follows: costing basis of the various phases; operational and maintenance reviews; sustainable development; risk assessment; reliability reviews; equipment availability; commissioning time; and environmental review.This paper endeavours to awaken people to the phases that projects require for a successful outcome and the management rigour that has to be applied throughout the phases to ensure the correct intellectual horsepower is applied at the right time to ensure the best outcome.Many of you would be parents and realise this is not unlike the development of children, teenagers, adults, retirees and ongoing.

Jan 1, 2002

The discovery since 1990 of four major orebodies in the Mt Isa Inlier - Century Zn-Pb, Osborne Cu-Au, Cannington Pb-Zn and Ernest Henry Cu-Au - only serves to enhance the already high stature of the Inlier in world mining importance. Currently the known mineral resources of the Inlier represent about 11 per cent of the world's Pb-Zn resources, five per cent of the world's Ag resources, and one per cent of the world's Cu resources. More can be expected to be added to these impressive figures given that two-thirds of the Inlier remains obscured by younger cover. Individually, projects such as Century and Cannington may ultimately achieve `world's best' status; Century's proposed production of 450 000 tpa of Zn metal would rank it close to number one with Cominco's expanded Red Dog project in Alaska. Cannington, with projected production of 660 tpa Ag, could become the world's biggest producer of silver. For comparison, Mt Isa produced 170 000 t of zinc metal and 335 t of silver in 1995. The apparent physical diversity of deposits in the Mt Isa Inlier is matched by a great diversity of opinion as to their origins. Because Ernest Henry is hosted by `porphyries', it is described by some as a porphyry copper deposit, despite mineralisation age possibly post-dating volcanic age by 200 Ma. Cannington Pb-Zn could be a Broken Hill-type (BHT) exhalitive deposit, or a late epigenetic replacement `regional skarn'. Mt Isa - Hilton Pb-Zn deposits appear to have experienced all deformational events and he syn-diagenetic in origin, or may have experienced little of the above and be epigenetic replacement deposits formed late in the major Isan orogeny, some 150 Ma after deposition.

Jan 1, 1996

By S Thacker, M Noakes

The Newmont Tanami Operations (NTO), formerly the Granites Gold Mine, commenced operation in the mid-1980s with tailings deposition evolving over the past three decades as production has increased and the operation has expanded. Paddock-style tailings storage facilities (TSFs) and in-pit tailings deposition have fulfilled the tailings requirements for NTO over its lifetime with the technical specifications of these facilities improving over time in line with the positive development of standards, guidelines and best practice.This paper reviews the options for tailings storage facilities at NTO and the many considerations that have been analysed and deliberated upon before settling on specific TSF types and designs. It also explains the operating philosophies of the tailings deposition and how the facilities have always strongly maintained the optimum capture and retrieval of water. The current TSF design and criteria is presented, along with the introduction of dry tails harvesting for use in paste production as a backfill product for the underground mine. Tailings deposition and recovery remains a critical function of the Granites process to ensure long-term operation and gold production.CITATION:Thacker, S and Noakes, M, 2015. Newmont Tanami Operations – tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 305–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By R Wolff

One critical factor in open pit mining projects is the estimation of the recoverable reserves. The reason for this is that at the valuation stage there is a lack of information about future metal prices and production costs. Consequently, the estimation of the recoverable reserves needs to be done based on a fixed break-even cut-off grade (BECG), in which fixed expected metal prices and production costs are assumed throughout the operating life of the mine (OLM). In this paper, an alternative technique for estimating the recoverable reserves of an open pit mining project is presented and explained in detail. The main characteristic of this technique is that it estimates the recoverable reserves of the project using mining costs as reference: this is done due to the fact that mining costs are easier to model than metal prices. Another important characteristic of this technique is that it uses the uncertainty of the geology of the orebody, given by simulations of the deposit, to make final strategic decisions, such as the selection of the operating life of the mine and the optimal production rate, which minimise the risk of not achieving future production targets while maximising the upside potential of future rewards. As it will be shown, the final outcome of the proposed technique is the generation of a robust open pit design, that include cutbacks and ultimate pit limits, called the marginal open pit mine design (MOPMD). One characteristic of the MOPMD is that, at each production period, it will be characterised by their respective geological uncertainty, given as probability distributions of ore, waste and metal quantities, and by marginal economical project indicators, such as cut-off grades and metal prices, among others. The details follow in the paper.

Jan 1, 2006

ALTHOUGH it has been a matter of about one hundred years since the idea of the internal-combustion engine entered the mind of the inventor, the practical application of its use was not attained till 1860, when Lenoir produced an engine similar to the ordinary highpressure steam engine, with the valves arranged to admit the explosive mixture and the discharge of the exhaust gases. In this case no attempt was made to compress the gas before ignition, as it was then considered that the explosion under these conditions had a detrimental effect, inasmuch as it would act as a sudden blow to the working parts. Indeed, he went so far as to inject steam and water sprays to reduce the explosion.Under these conditions the consumption of gas was exceedingly high-about 106 cub. ft. of coal gas per b.h.p. per hour but the mechanical effect showed that the engine ran in every respect as smoothly and quietly as in best steam-engine practice.The extravagant consumption of this engine was clearly pointed out at the time by Gustav Schmidt in a paper before the German Society of Engineers, wherein he states :-" The results would be far more favourable if compression pumps, worked from the engine, compressed the cold air and cold gas to three atmospheres before entrance into the cylinder. By this means a greater expansion and transformation of heat is possible."

Jan 1, 1912

By J Loeb, R Ramanathan, H Ingham, P Cameron

Most mining operations, including iron ore, maintain a focus on continuous improvement and asset optimisation in their operations. As all the unit operations in the Mine-to-Mill value chain are interdependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and impact of changes to the process. In this paper, we discuss some of the critical attributes in the Mine-to-Mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve Mine-to-Mill processes. Mining operations are planned and executed based on designs and models to achieve the operation's objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Therefore, measurement of the key attributes establishes the baseline for Mine-to-Mill (or Pit to Plant) performance, which is necessary to understand the impact of any proposed improvements to the process design and execution and monitor the outcomes on an ongoing basis sustain the improvements that have been implemented. This paper focuses on two types of measurement – blast movement and particle size of materials through the Mine-to-Mill process. Several innovative technologies and control loops are readily available to measure these attributes and assist operations to improve productivity and mine site profits. The size of the tangible benefits, which can flow from measuring and optimising fragmentation and blast movement, provide a remarkable return on the investment. Realising these benefits needs a focus outside conventional operation silos as a successful Mine-to-Mill project requires a multidiscipline approach across all the silos in the value chain. Required technologies are available; adding the necessary ingredients of communication and co-operation by all concerned across the silos will ensure the benefits are realised.

Nov 8, 2021

By Y M. Lee, Y Hong, B C. Kim

Since sintered ore is the primary source for producing molten iron in the blast furnace process, maintaining stable quality despite the utilisation of low-grade iron ore is crucial. However, conventional analysis methods, such as chemical composition, ore size distribution and types of iron ore, have limitations in developing the utilisation of new low-grade iron ore and predicting sintered ore properties. Sintered ores are formed through a complex melting process of granule particles consisting of iron ore, flux and fuel. Consequently, it has been investigated that analysis methods which apply the reactive properties of iron ore to predict sintered ore characteristics. In this study, we estimated the properties of iron ore by simulating the assimilation process of coarse ore, which influences the bonding strength of sintered ores and quantifying the degree of assimilation reaction. Pseudo particles were formed by granulating coarse ore (1–3 mm) with adhering fines, which act as primary melts and sintered at 1623 K. The bonding strength of individual sintered ores, formed from 11 different types of iron ore, was measured using a simplified Tumbler Index (TI) test and each value was indexed as the Iron ore Reactivity Index (IRI). By investigating the relationship between the degree of assimilation depending on iron ore properties and the characteristics of sintered ore, we demonstrated that sintered ores formed from more reactive iron ore exhibited stronger bonding strength. Moreover, when blending conditions resulted in a higher Iron Blending ore Reactivity Index (IBRI), the physical properties of sintered ore improved. The development of this analysis method is expected to not only enable careful consideration of iron ore usability but also allow for the advance prediction of sintered ore qualities by deriving the IBRI.

Sep 18, 2023

The purpose of this paper is to outline the equipment used for diamond drilling at Mount Isa, together with alterations and recent improvements therein. As the majority of the drilling is carried out with machines running at relatively high speeds using XRN blast hole bits, the paper is mainly devoted to this branch of drilling.Because diamond bit costs constitute the major expense, a considerable amount of research into bit design has been carried out, and in several instances, costs per foot have shown an appreciable decrease in spite of rising manufacturing costs and higher diamond prices. Equipment performance has at times been erratic due to delays in delivery and occasionally because of faulty parts, but in general the position has improved by keeping in close contact with the manufacturers.BLASTHOLE DRILLING MACHINESThe standard blasthole diamond drill is the 'E-500' two cylinder air powered model manufactured by Mineral Drillers Limited. Several of the older pattern JV41 are still in use, but are being retired as they wear out.. Machines are repaired in the underground diamond drill shop.The normal feed gears used when drilling in lead shales are 350 top gear and 450 low gear-actually 357 and 438 revolutions per inch of advance respectively. The 300 gear was commonly used several years ago, but it was found that bit footages could be increased without any appreciable drop in penetration rate by reducing to the 350 gear. Gears used for copper drilling are 650 and 750. Footage per shift...

Jan 1, 1953

By B Green

With a focus on safe productive tonnes, there has been an ongoing drive to increase the productivity of the mining fleet across BHP Billiton. In response, a team from the Iron Ore business was formed to review all aspects of the end-to-end drill and blast process and to challenge conventional practices that limit production efficiency. As a result of the outcomes of this work, a number of initiatives were identified to improve operational practices that have also delivered significant cost savings.One such initiative was to increase pattern size to a minimum of 1 Mt where practicable, thereby creating ‘megablast’ as a new standard across all mines. To achieve blasts of this size, the team had to overcome the complex problem of integrating wall control into the megablasts.With traditional blasting techniques, the key strategy, which is also historically inefficient but was thought to be integral to having stable, safe walls, was to utilise the trim blasting/modified production blasts technique (ie narrow blasts along the pit wall designed to ‘peel off’ the material while minimising the effects of vibration and charge confinement on wall integrity).Small traditional trim patterns comprise three to four rows of production holes and one or two rows of batter/buffer holes of reduced diameter that require the firing face to be completely exposed before blasting. This is an extremely slow process that requires a lot of resources for very little tonnage while adding additional expense to the final cost per tonne.This paper will show how the megablast approach was developed to control damaging vibration and confinement effects, flyrock and fragmentation while having the largest possible blast that includes wall control. The new practice is based on a theory that involves the initiation point and control row being the second row of holes from the pit wall itself. Adjusted charges in vented batter and buffer holes help to achieve an optimal toe design, and at the same time create a zone of broken ground that absorbs damaging vibrations formed by the attached production blast of any size, whether it is a straight wall or a multi-angled complex pit shell design.Using the new style of blasting has allowed an increase in the size of the patterns from an average of 300 kt to over 1 Mt whilst maintaining pit wall integrity. Case studies will be presented showing drill, charge and tie-in designs with the presentation having additional blast videos, including overall shots of blasts and in-close footage of what happens behind the blast at the crest of the planned catchment berm.The paper will also demonstrate the flow-on effect of using this style of blasting to reduce operational costs associated with other downstream processes, such as the reduced requirements for pattern preparation, an increase in productive digging, reduced maintenance costs and a decrease in fuel burn for equipment.CITATION:Green, B, 2015. Megablasts – enabling technologies in BHP Billiton Iron Ore, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 599–606 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Fletcher

Pacific Hydro, a leading renewable energy company from Australia, is developing a series of cascading run-of-river hydro electricity projects in the Cachapoal Valley at the base of the Andes Mountains some 100 km south of Santiago in Chile.These projects involve extensive tunnelling and underground works. The first of these projects is called Chacayes (110 MW installed capacity) and is now under construction with Astaldi SpA of Italy and Fe Grande of Chile as the EPC contractor. Astaldi SpA also has an equity stake in the project. It involves 6 km of tunnels between 5 m and 7 m diameter, of which 2.3 km is by tunnel boring machine (TBM) (5 m diameter).This paper outlines the local and regional geology, the scope of the Chacayes project, actual tunnel excavation rates and support, and compares the decision making on Chacayes between a choice of traditional drill and blast excavation versus TBM.The paper also outlines the next project planned to be developed by Pacifi c Hydro in the valley – the 140+MW Nido de Aguila project involving a main tunnel drive of 11 km with two intermediate adits, plus a 388 m shaft and underground powerhouse. The main tunnel drives are likely to be excavated by two hard rock TBMs (5 m diameter) but will need to be able to withstand high overburden pressures of up to 1300 m.Subsequent projects in the planning stages include the downstream Coya II project with two tunnels totalling approximately 10 km, one of which may be by TBM.

Mar 8, 2011

By A M. Ebbels, D Pratt

The current commodities super-cycle has seen an explosion in the number of mining projects demanding human resources throughout the world. The demand for key personnel currently far outweighs the international talent pool and will take several years to subside. A highly effective project team can be the difference between a successful project and a bad public relations exercise. Building an effective team and retaining the team members has become one of the major influencing factors for successful project development in the mining industry in the last decade.Increasingly, international teams are being established combining skill sets, subject matter experts, unique previous experiences and diverse cultures to deliver mining projects all around the world.This paper explores the characteristics of a highly effective team, the communication and geographic challenges and some potential pitfalls which influence the ability to form effective teams within the mining industry.CITATION:Ebbels, A M and Pratt, D, 2012. A great project team - Bringing together location and culture, in Proceedings Project Evaluation 2012 , pp 197-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By S W. Houlding

The Certificate in Mining Studies program at the University of British Columbia, Vancouver, Canada is a collaborative initiative between mining schools and industry to provide accessible, cost-effective, accredited continuing education and training, designed to address the future needs of the global mining community. Content is provided by industry specialists and delivered through an integration of online learning, short courses and interactive webcasts. Accreditation is provided by a network of mining schools. In 2011, the program will deliver close to 100 short courses and interactive webcasts and provide 24/7 access to more than 130 online courses in six mining streams, to participants from as far afield as Tanzania, Argentina and Mongolia. The program is proving adaptable to corporate and mine site engineer-in-training and graduate-development programs, as well as providing accessible professional development opportunities for individuals. It also provides opportunities for cross-training from other disciplines and integration with mining school curricula.

Nov 22, 2011

By R Price, B H. Miller

"The rise of autonomous haul truck fleets may have been initially driven by the rapid escalation of the cost of equipment operators, but the actual improvements reported by the major iron ore miners far exceeds the simple reduction in workforce. Utilising cost models developed for feasibility studies and mining contract modelling, the limits of cost improvements due to simple labour reductions are compared to those achieved by the early autonomous fleet adopters and through traditional process improvement techniques such as fleet class upgrades or hot-seating of equipment. As autonomous fleet implementation matures, it is likely that the gains seen by current adopters will seem minor compared to the limits generally governed by the limit of equipment utilisation. This ultimate limit is explored through time utilisation models, which were also developed for use in feasibility studies and mining contract modelling.Citation:Miller, B H and Price, R, 2016. Autonomous Haul System Savings - It's Not about Less Truckies but Better Truckies!, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 2–10 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

The process of electrostatic separation was developed in the late 19th century, but did not make much headway for about 25 years. High dc voltages, of the order of 20 kilovolts, are involved, and the only means of obtaining such voltages at that time were by the use of frictional machines, such as the Wimshurst. These were not reliable, for two reasons:-a. If a spark discharge occurred it took an appreciable time before a steady voltage was again attained.b. In damp weather the machines were almost useless.In the first 20 years of the 20th century the advent of mechanical and vacuum-tube rectifiers led to promising developments of 'the process. In the early 1920's flotation became widely used commercially, and proved to be more reliable, and capable of wider application, than electrostatic separation. During the last 15 years or so, with a better knowledge of the fundamentals forming the basis of the process, electrostatic separation is beginning to compete with flotation, especially in the treatment of smallsizedgranular material, such as beach sands. Electrostatic separation can be, and is, widely used in many cases where flotation is impossible, such as in the cleaning of food products which must be kept dry.

Jan 1, 1950

By E Wargem

The optimum mining of an orebody in an underground mining operation is fundamental to the mine’s ability to operate both sustainably and efficiently. The effective mining of an open stope or a cave is largely reliant on the recovery of the initial void created by conventional drilling and blasting. These initial voids are known by various names such as a Longhole Rise, Slot or Winze and can be mined either as a downhole or as an uphole. Regardless of the underground mining method, the process of the design and implementation of this initial void is largely uniform across many operations with various patterns of slot or winze designs used across these different operations. Diligent design, implementation and review strategies in drilling and blasting of these will facilitate cost-effective mining with minimal disruption to mine schedules and production targets. When an operation struggles in opening the initial void in underground mine blasting, it has a negative impact on productivity, mineral recovery, and the overall economics of mining. Near field blast vibration monitoring is a vital tool to use in analysing slot blasts and will provide additional feedback into the reconciliation part of the drill and blast process. It is one that is often overlooked in the mining industry in many operations due to many factors such as lack of skilled personnel, or a lack of required resources. The data obtained from near field blast vibration monitoring can be used to provide additional feedback into blast reviews and help in any drill and blast optimisation projects. This paper highlights key aspects of underground drill and blast reviews and the use of near field blast vibration monitoring for post blast analysis and shares learnings from various projects that the authors have been involved in within Australia and abroad.

Mar 29, 2023

By B Morey, J Gordon, P Mackenzie

Mount Tom Price Mine is peerless amongst Rio Tinto iron ore resources around the world. It has provided Hamersley Iron with premium quality, high lump yield haematite ore over the last four decades. The Brockman type bedded ore, containing bands of haematite and shale of varying thicknesses has been traditionally bulk mined to either high-grade or low-grade based on alumina cut-off grades. As open pit mining has progressed deeper into the orebody approaching the keels of the megastructure, increased structural complexity, chemical and physical variations in the ore, unfavourable ore presentation and reduced blending options have become an issue for grade control and may have serious impacts on product stockpiles. The grade blocks and boundaries must be accurately defined according to geological contacts and where identified, selective mining may be applied. Therefore in-pit geological mapping is the definite and ultimate guide to achieve target grades and grade predictions. Under this scenario, it is absolutely vital that the mine geology team ensures this geological knowledge is passed onto the related departments including mining crews as well as to the short- and long-term planners.

Jan 1, 2002

By A R. Bye

The mining industry is facing some key challenges that provide a compelling case for geometallurgy initiatives. Over the last 30 years, the average grade of Australian orebodies being mined has halved while the waste removed to access the minerals has more than doubled. In the last eight years, the industry’s energy consumption has increased 70 per cent while multi-factored productivity has fallen 24 per cent. The paper documents a broad range of industry case studies which demonstrate strategies for gaining value from geometallurgy.The mining industry constantly faces the key questions of how significant ore variability is on mine valuation and how would knowledge of the variability change the mining schedule, mine to mill design and operation. Using case studies the paper describes the methods used for incorporating mineral extraction attributes into orebody models and their technical integration into daily operation as well as mine planning optimisation. While pit optimisation from a fully attributed geometallurgical model highlights areas of opportunity and risk it is shown that during the scheduling phase of mine planning that significant value can be added. The benefits from these projects included reducing geotechnical and environmental risk, improving mine to mill performance, option analysis and quantified cash flow risk. There is growing acceptance within the minerals industry that ‘realistically assumed modifying factors’ defined by a competent person/s are not sufficient to mitigate the risk of funding mining ventures. Geometallurgy is moving away from factored ore reserves to data-rich block models providing reliable information for mining, metallurgical and environmental considerations.

Sep 5, 2011

By E Westthorp

Final mine sealing of BMA’s Crinum North mine, near Emerald, Queensland was undertaken in December 2015. Due to the benign atmospheric environment at Crinum North, the Queensland Mines Rescue Service (QMRS) Górniczy Agregat Gasniczy (GAG) unit was utilised to reduce oxygen levels throughout the underground atmosphere as part of the final sealing process.The GAG was utilised by way of a vertical borehole from the surface to seam to successfully reduce oxygen levels throughout the underground mine workings. Application of the GAG unit enabled the underground mine to be classified as stable and inert within days of the GAG operation, and subsequently cease gas monitoring at Crinum North. The data and information obtained from this activity provides valuable information to the underground coal mining industry on successful application of the GAG in realistic situations.This paper discusses the strategy used for sealing, the assisted inertisation and the results obtained from the application of the GAG unit. It discusses both the overall results and gives a detailed review of the gas monitoring data obtained via the tube bundle and real-time system, both during and following the use of the GAG unit.Gas monitoring results obtained and the strategy used are critical to share with the industry to obtain a better understanding of how the GAG unit works, and how it can be applied for emergency preparedness, emergency response or planned inertisation.CITATION:Westthorp, E, 2017. A review of the strategy and gas monitoring results obtained during the use of Queensland Mines Rescue Service GAG unit at Crinum North mine, in Proceedings Australian Mine Vent Conference 2017, pp 309–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017