Search Documents

By S C. Dominy

Gravity amenable gold ores are those that after comminution produce liberated particles, composites and/or carriers that can be recovered by gravity separation means. Recovery depends upon mineralisation type and the comminution and concentration method used. Any in situ ore with more than 20 per cent of gold greater than 100 µm in size is likely to have a strong gravity recoverable component. A less traditional approach is where the gold is sulfide-locked and the gold carrier plus any liberated gold is recovered via continuous gravity recovery following fine crushing. Specific tests are undertaken to determine the level of gravity amenable gold within a deposit. The principal methodology is the gravity recoverable gold (GRG) test, which consists of three sequential liberation and recovery stages. For continuous gravity recovery (CGR), the sample is fed over a laboratory Wilfley table to simulate continuous recovery of the gold. Tails from the feed can be progressively re-ground and re-tabled to develop a grade-recovery curve. Primary geology and gold particle size-distribution have a strong effect on the mass of sample required to provide representative results for both tests. Where low-grade ore contains very coarse gold, substantially larger sample masses are required. Experience has shown that GRG and CGR values can vary throughout an orebody, particularly within different geological-grade domains. A testing regime must consider sample frequency and support.

Sep 5, 2011

By W Curlewis, D Hake, Z Cuthbert

The South Island Line (East) will be a medium-capacity railway covering approximately 7 km from Admiralty Station to South Horizons Station on the south side of Aberdeen Harbour in Hong Kong, with intermediate stations at Ocean Park, Wong Chuk Hang and Lei Tung.South Island Line (East) Contract 904 project is located on the island of Ap Lei Chau at the southern side of Hong Kong island and requires extensive construction works to be completed in close proximity to the existing residential estates of South Horizons and Lei Tung. The project also has areas of significant cultural heritage, including 18th and 19th century temples and historical gravesites. Owing to the site access constraints and location for the project, detailed planning and methodology innovations have been required to ensure the most effective and responsible means of delivering the project works. To excavate the tunnels using drill-and-blast techniques in these restricted locations, the maximum instantaneous charge weight that could be fired while blasting was severely limited. To overcome these restrictions, the project team developed and pioneered the use of ‘deck loading’ in Hong Kong to minimise the impact of blasting operations and has successfully implemented double- and triple-deck blasting operations during the completion of tunnel excavation works.Upon completion of the drill-and-blast excavation, the tunnel lining works were completed using both in situ concrete lining with travelling forms and permanent shotcrete works.CITATION:Curlewis, W, Cuthbert, Z and Hake, D, 2014. SIL904 Hong Kong – Drill and Blast Tunnels, station blasting innovations (double- and triple-deck blasting) and lining solutions, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Webster-Brown

The Tui Mine is an abandoned Pb-Zn mine giving rise to water quality problems in the Te Aroha region of Coromandel, New Zealand. When sampled in September 2002, for example, both the Tui and Tunakohoia Streams draining the mine site exceeded ANZECC (2000) water quality guidelines for aquatic life protection (Cu, Cd and Zn) and recreational quality (Cd). Based on trace metal mass flux (kg/yr) from parts of the mine site, the principal pathways by which Cu, Zn and Cd contamination reach these streams have been identified as:the tailings dam leachate,the diverted stream water from above the dam,the drainage from Adit 5 (which accounts for 95 % of Zn and Cd contamination in Tunakohoia Stream), andto a lesser extent, run-off from waste rock piles below Adit 4 level. Of the various remediation options, which have been proposed for the site, the following are identified as providing the best protection for the Tui and Tunakohoia streams:stabilising the tailings dam embankment and capping the embankment and tailings,constructing and/or cleaning out engineered diversion drains around the perimeter of the tailings dam to divert surface water away from the tailings dam, andinstalling bulkheads within Adit 5. A formal postal survey of the people of Te Aroha (66 respondents from 230 surveys) indicated that their priority was that the site be made safe for the public to visit, and used for recreation. As soil samples in potential recreational areas of the mine site, significantly exceeded guideline values for Cu, Pb, Zn, Cd and As, soil removal or capping clearly also needs to be part of a remediation plan. Development of the site as a historical/ecotourism area was viewed favourably, as this may encourage more visitors to the Te Aroha area as well as educate local residents.

Jan 1, 2003

By M J. Dunn

The geotechnical model is the cornerstone of any mining geotechnical design and as such the confidence level and reliability of the geotechnical model is paramount. The geotechnical model confidence level needs to be commensurate with the level of design that is being applied or study that is being undertaken. The geotechnical model is made up of several components and the reliability of the data underlying these components ultimately determines the reliability of the geotechnical model.Data reliability is linked to the quantity of data collected, the spatial distribution of the data collected, quality of the data collection and the interpretation of the data. In a typical project, there is an opportunity to improve data reliability through the scoping, prefeasibility, feasibility and final design and implementation stages.Currently, very little quantitative guidance exists in the literature on assessing the confidence level of geotechnical studies, although there have been attempts by various authors (Haile, 2004; Haines, Swart and Kruger, 2006; Read and Stacey, 2009; Dunn, Basson and Parrott, 2011) to qualitatively describe what level of geotechnical data is required. Recently a number of authors (Read, 2013; Fillion and Hadjigeorgiou, 2013; Thomas, 2013) have outlined methods that could be applied to assess the reliability of some types of geotechnical data that are used in the development of geotechnical models.This paper briefly discusses some of the factors influencing data reliability and the geotechnical model confidence and some of the tools available.CITATION:Dunn, M J, 2014. Geotechnical models and data confidence in mining geotechnical design, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Stepanenko, G Stovpchenko, L Lisova, D Togobitskaya, L Medovar

Classical electroslag remelting of consumable electrodes is a drop-by-drop melt feeding through a slag layer into a renewing molten metal bath, slowly solidifying into a homogeneous, dense, defectfree ingot in a copper water-cooled mould. The new look at the additive nature of the electroslag remelting (ESR) process in a protective atmosphere allowed us to formulate the principles of a comprehensive thermodynamic-based model that can predict dynamic changes in slag and metal composition at certain ingot remelting. The model considers drastically different slag-to-metal mass ratios at the beginning and end of remelting and predicts gas, slag and metal composition in a chain of thermodynamic subsystems. Despite consisting of calcium fluoride and stable oxides, the ESR slag can oxidise main and active elements from steel and alloys (primarily aluminium, titanium and silicon) due to chemical reactions between slag and metal. ESR is not an electrochemical process in its nature. However, slags are ionic melts and deviation in their composition causes a change in their properties, affecting both operation mode and ingot quality. Another important understanding derived from the modern metallurgy technological route is that the ability to refine metal from impurities is not a priority for the ESR because consumable electrode has already passed all stages of refining and deep degassing at ladle treatment that changes ESR slags engineering principles. The critical importance became slag’s ability to generate process heat and keep the melting composition in the metal bath unchanged (except for non-metallic inclusions assimilation). Slag engineering for ESR required a compromise between chemical inertness to a metal composition and desired physical properties deriving from technological reasons. The Directed Chemical Bonds Concept (DCBC) in a multicomponent oxide system was used to build predictive models of electric conductivity and the melting temperature of fluoride-oxide slag based on their chemical composition. Both models help to design a customised composition of effective slags for steel and alloy groups or individual grades, and they are significant steps in the development of a comprehensive model of electroslag remelting.

Aug 21, 2024

By T Napier-Munn, E Louwrens, L Keeney

Geometallurgical characterisation of ore deposits is accepted practice in some parts of the mining industry today. Its primary aim is to provide constrained inputs that reflect inherent geological variability and its impact on metallurgical performance for the deposit. Geometallurgy improves project value because it suggests more valuable alternatives for scheduling and processing through an increased knowledge and understanding of the interactions of rock properties and extractive technologies. Lower project cost (both capital and processing) and improved recoveries are the result from closer tailoring of the mining and mineral processing strategies to the characteristics of the resource (Dunham, Vann and Coward, 2011). Tailings storage facilities (TSFs) can be seen as potential resources and it is argued that fundamental geometallurgical characterisation as applied in ore deposit characterisation should also be applied to planning the retreatment of TSFs. This paper will describe a research project at Julius Kruttschnitt Mineral Resource Centre assessing if geometallurgical principles and methodologies can successfully be applied to TSFs as they have been to primary deposits. The project is establishing a new standard method of tailings evaluation which will include a 3D spatial model of the tailings resource. Initial domaining of the TSFs was done using principal component analysis followed by k-means cluster analysis based on chemical assays from drill core samples. The subsequent characterisation of the drill core samples has involved chemical, mineralogical and metallurgical profiling, with a range of metallurgical tests being conducted on the samples. This characterisation step is followed by class-based analysis, predictive modelling and process performance domaining with the ultimate objective of establishing a 3D spatial model incorporating geochemical, mineralogical and metallurgical performance data. This approach, which takes into account processing performance permits a more realistic (as compared to doing limited chemical assays and metallurgical testing) economic evaluation of the potential of reprocessing the tailings material. It is believed that the approach is generic and can be applied to other TSFs being considered for reprocessing. The present case study has also established the gold, copper, magnetite and cobalt deportment for an iron oxide copper-gold deposit tailings resource.CITATION:Louwrens, E, Napier-Munn, T and Keeney, L, 2015. Geometallurgical characterisation of a tailings storage facility – a novel approach, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 125–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

By T Sparks

The Collie River catchment, located approximately 200 km south of Perth, covers an area of around 2830 km2 and is the source of run-off to the Wellington Dam, an important irrigation water resource for the Collie Irrigation District. The salinity of the Wellington Dam has increased due to historical clearing and irrigators currently use water with salinity levels approximately twice that of the Murray River in South Australia (Water and Rivers Commission, 2001). The Collie River Salinity Situation Statement (2001), released by the Water and Rivers Commission (now the Department of Water), identified realistic actions that could achieve the salinity reduction target. Subsequent benefit-cost analyses and prefeasibility studies recommended the diversion of the most saline flows in the Collie River away from the dam as an immediate intervention (URS, 2003). The East Branch of the Collie River above the locality of Buckingham (20 km east of Collie) contributes around half of the salt that flows into the Wellington Dam and the diversion and storage of the saltiest flows from the East Branch at Buckingham was identified as a viable option for reducing salinity in Wellington Dam. The proposal had one problem û the water could not be disposed of as quickly as it was diverted. However, in the vicinity of the diversion site were a number of coal mine voids and after preliminary discussions, the Government/Griffin Coal alliance was formed and from this the opportunities have continued. Diverted water would be stored temporarily in an adjacent mine void (Chicken Creek 4 void) and then disposed of to the sea. The disposal options included Western Power CorporationÆs saline discharge pipeline from Collie Power Station, or a new pipeline. The diverted water was also identified as a potential raw source for treatment and use in industry. This has opened up opportunities including desalination, water efficiencies in the power stations, increased reliability of water supply for the power stations, water for new industries, wastewater disposal options and extra water for PerthÆs water supply. In the process of solving the water storage problems the project introduced a range of mine water quality problems û heavy metals and pH û and the Department of Water (DoW) is now working with the mining industry and the Centre for Sustainable Mine Lakes (CSML) to develop treatment and management technologies. The project has received support and funding through the National Action Plan for Salinity and Water Quality (NAP) and it has been possible to accelerate and enhance this project as a result of NAP. The DoW has developed the proposal to an advanced stage and gained approvals for the capital diversion program to go ahead. The partnerships have expanded to include the second mining company, Premier Coal, the Water Corporation, Western Power and the Harvey Irrigation Cooperative. The proposal could feasibly result in a $90 million integrated water management initiative for Collie using the latest technology, mining operations and providing water for value adding industries in the local area. The DoW is not a mining company; however, our experience in managing water in times of shortage, environmental water quality criteria, competition for water and managing community expectations will have the same success factors:consultation and knowing your community and stakeholders, sharing issues and working in partnership can provide results far greater than the initial issue, even brackish water has value, every sector is in competition with each other and has to have a share of the water, an integrated approach can provide opportunities for development in areas of water shortage, and never think of water as wastewater.

Jan 1, 2006

By P J. Fairfield

"This paper reflects on the author’s experiences in undertaking mining studies and reviewing mining projects and technical reports, particularly over the past five years, and the impact of recent changes in reporting standards and listing requirements pertaining to mining-related evaluation and valuation exercises. It also discusses contemporary changes in the expectations of the investment community and the implications for the role of the technical specialist in providing advice to such stakeholders.Not for the first time in history, the resources industry has experienced a significant downturn after a period of strong, sustained growth in line with the traditional view of the cyclical nature of commodity markets. The resource industry is currently faced with capital austerity in the wake of projects ‘failing’ (not delivering to expectations). In response, the industry has experienced changes in investment behaviour (slowing of investment) and an increasing regulatory burden as stakeholders seek a greater understanding of mining project risks.This paper discusses this response and uses case studies to highlight the key learnings (perhaps re-learnt) by the industry. It also discusses the challenges faced by technical specialists in communicating the results of technical and valuation studies to the investment community.As investors seek to take advantage of the current stage in the investment cycle, the key challenge of the technical specialist is to effectively communicate the uncertainty in technical assumptions, risks and opportunities that drive project value.CITATION:Fairfield, P J, 2016. Managing expectations – from buyer beware to buyer be aware, in Proceedings Project Evaluation 2016, pp 66–74 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By R Varden

Friction rock stabilisers, commonly termed ‘Split Sets’, friction rock bolts, or continuous friction coupled bolts are the most widely used rock bolt in the Australian underground metalliferous industry. Historically, they were used for temporary reinforcement, mainly within ore development. However, their use as primary reinforcement has grown with the demand for higher development rates at lower costs. The introduction of galvanisation has increased their longevity and pattern bolting in conjunction with weld mesh, specifically made for use in development headings, has allowed the use of friction rock stabilisers to increase rapidly with development jumbo’s undertaking the installation. The installation of friction rock stabilisers appears to be deceptively simple, particularly when compared to resin encapsulated bolts. The friction rock stabilisers capacity is a function of the borehole parameters, rock mass quality/strength, the bolt dimensions and steel quality, and lastly and perhaps the most important the operator skill levels. However, as in industry we are still seeing common occurrences of friction rock stabilisers not reaching their design pull test capacity. Pull testing the friction rock stabilisers is used to verify the installation of the design capacity. It involves loading the collar of the bolt with a hydraulic ram until the design load is reached or the bolt slips. Pull tests often show failure rates of 20 per cent or higher. This is despite over 40 years of use and with millions of units installed annually. Such high failure rates would suggest there remain issues with the quality of installation. Ground support quality assurance and quality control (QAQC) programs are needed in combination with operator training to ensure that pull test failure rates are kept as low as practical. However, there are times when despite the QAQC being completed the pull test failure rates increase quite suddenly. When this occurs, it is important to conduct a thorough investigation. These investigations often show there are several factors that are not obvious to personnel installing the bolts. To complete a useful investigation, it must also be done methodically, working through the entire process that includes less obvious factors such as steel quality and the calibration of the hydraulic pull test kit. The aim of the paper is to give mine practitioners an understanding of the complexities of friction rock stabilisers, what QAQC requirements they should be doing on-site, what can go wrong during installation and, if necessary, a process of how to conduct investigations into high friction rock stabiliser pull test failure rates.

Mar 29, 2023

By K P. Tully

In August 1996 a Microseismic Monitoring System developed by ISS International Limited was installed at the Pasminco Broken Hill Mine -Southern Cross area. The project aims were to:Assist in daily safety management in a mine environment which exhibits one of the highest occurrences of microseismic activity recorded in the Australian mining industry. Be used as a proactive tool in design of future development and stoping. The project to-date has been an unqualified success in achieving both goals. Consequently the system is being expanded from 6 to 14 monitoring sites.

Jan 1, 1998

Previous methods for measuring the flow of solids in Jnrdraulic conveying have not considered the important effects of slip velocity and particle concentration. In this paper an extension of the method proposed byShirato et al. (J. Chem. Engng. 'Japan, 1: 164-167) for determining mass flow in a vertical conduit is outlined.The present method consists of measuring' the volumetric flow of the slurry (by a magnetic flow meter for instance) and the density of the slurry in two pipe sections of different diameters. Effects of variation of slip withparticle concentration, not previously considered, are allowed.Problems involved in estimating the density of a slurry from differential pressure measurement are discussed.The major problem is the uncertainties in estimating frictional losses due to the wall in two-phase flows. The greater reliability of a more "direct" technique, such as by 'Y-ray absorption, for measuring solid concentration is emphasized.

Jan 1, 1971

The Stawell Goldfield, the westernmost of the main Victorian fields, has produced over a million and a quarter ounces of gold from one and three-quarter million tons of ore. The lodes are quartz reefs and sulphide bodies occurring in sediments of lower Ordovician or upper Cambrian age. The lodes are confined to a relatively narrow suite of weak rocks lying between stronger ones above and below and there is a definite relationship between fold structure, pitch and strength of folding and ore.LOCATION HISTORY AND PAST PRODUCTIONThe town of Stawell, situated 150 miles north-westerly from Melbourne on the main railway and road to Adelaide, is the most westerly of the main gold areas of Victoria. Alluvial gold was found at Pleasant Creek (now Stawell West) in 1853 and the usual "rush" followed. Numerous alluvial leads, some surface, others buried under up to 100 ft. of Tertiary sediments were worked. The alluvial gold was soon exhausted, but in 1857 gold-bearing reefs were found on the slopes of a prominent ridge on the northern edgeof the present town. Early reef mining was by small working parties mining to shallow depths only and treating their ore at public crushing plants. Some of the early returns were very high grade. The next stage was the amalgamation of claims and the formation of companies, with their own treatment plants. This stage continued till the last mine closed in 1921. These companies had, by present standards, small holdings and far too many shafts were sunk, resulting in less efficient prospecting and operation.Since 1921 there have been one or two small scale attempts to revive mining but without success. Of recent years Gold...

Jan 1, 1960

By B Miles, D J. Williams, J Ahn, T A. Vangsness

The flooding of open strip coal mines in the Bowen Basin and Hunter Valley Coalfields of Eastern Australia has the potential to soften the spoil and floor materials to produce “mud”. This mud can act as a slip plane or weak zone when spoil is dumped into it, resulting in geotechnical instabilities. It is therefore important to understand the mechanisms and degree of degradation likely to occur within coal mine spoil of different qualities.To investigate this, five clay mineral-rich coal mine spoil samples were collected from the Bowen Basin, and each sample was subjected to wetting and drying cycles to simulate degradation that could be expected on wetting-up in situ, with their particle size distribution analysed both before and after degradation. These results were compared with the results of a modified slake durability test, in which the entire sample was tested.The paper presents the results of the accelerated degradation and modified slake durability tests on each of the five spoil samples. These results were related to the physical and geochemical characteristics of the samples, which highlighted their importance. The modified slake durability test may be used to rapidly simulate the expected in situ degradation of coal mine spoil on wetting-up, enabling susceptible spoil materials to readily be identified.CITATION:Vangsness, T A, Williams, D J, Ahn, J and Miles, B, 2018. Accelerated degradation and modified slake durability testing of clay mineral-rich coal mine spoil, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 83–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Thank you and good morning. I am delighted to be here and to see so many of my colleagues and competitors. The general topic of this week's conference - World's Best Practice in Mining and Processing - suggests a focus on mining and processing. I am somewhat of a `jack of all trades and a master of none'. But I'm not even a jack when it comes to mining and processing technology and practices, and so I will leave those topics to speakers better 'qualified than I. Instead, what I would like to do is give you my thoughts on the best management practices of mining. You see, the times are changing for the mining business. There is great uncertainty in our industry. Anyone who received their education in an English-speaking school probably remembers the famous poem `Invictus' by William Ernest Henley. The two most famous lines from that poem are, if you remember, `I am the master of my fate; I am the captain of my soul'. The fact of the matter is that the metals industry, including the copper industry, is not the master of its fate. To a great extent we're at the mercy of forces over which we have little control, such as the world economy or political situations in individual countries. The copper industry is like a surfer at Manly - we can't influence where the wave is going; all we can do is stay in front of the curl and on our board. Historically, discovering, developing and processing ore reserves were the primary facets of our capital intensive business. To stay competitive today, we must invest equally in intellectual capital - our employees - in order to succeed in the face of economic, regulatory and political challenges and global competition (Schonberger, 1986). Everyone seems to have a different theory about being competitive. A lot of people use sports analogies when talking about competition. Others, like American businessman and former US presidential wanna-be Ross Perot, take a more interesting approach. In Mr Perot's hypothetical corporation, competition is a lot like having a snake in a factory. If someone sees a snake, the first thing they do is create a committee on snakes. Then, the committee on snakes meets and discusses the problem for a couple of years. The most likely course of action is nothing. Everyone figures that the snake hasn't bitten anyone yet, so they just let him crawl around the factory floor. Perhaps a vice president of serpentine affairs is appointed to continue watching the snake - making sure it doesn't grow. Ross Perot sees it a little differently. In his corporate world, business needs to build an environment where the first guy who sees the snake kills it. Of course in our industry, we better make sure the snake isn't on an Endangered Species List before we go after it! I am not going to talk about competition and competitive forces in terms of sports or snakes, but I would like to share some thoughts with you about how the mining industry can better utilise competitive thinking to get ahead and stay there. You may be wondering how an executive from a 160-year-old company could know much about competitive spirit, but the founding ancestors of Phelps Dodge were wizards at identifying

Jan 1, 1995

By R Soong

The Wharekirauponga (WKP) epithermal gold-silver deposit is located about 10 km north of Waihi in the Hauraki Goldfield east of Auckland. WKP is notable for its sheeted to stockwork quartz veins hosted in rhyolitic rocks, that have attracted exploration interest as a low grade, bulk tonnage exploration target. Exploration between 1978 and 1993 included 23 diamond drill holes totalling 5505 m. The mineralisation occurs in a rhyolite dome complex (Miocene), consisting of flow-banded rhyolite and rhyolitic pyroclastic rocks, with minor andesite. Fifty four drill core samples were collected from six exploration drill holes and analysed by semiquantitative XRD techniques. Hydrothermal alteration of the rhyolitic and andesitic rocks has developed secondary mineral assemblages of quartz, adularia, albite, chlorite, illite, sericite, interlayered illite-smectite, carbonate, halloysite and pyrite. The main zone of mineralisation is characterised by quartzadularia alteration, which grades oiItward to quartz-clay (illite, local halloysite and/or interlayered illite-smectite) alteration. Propylitic alteration is present at the southern end of the drilled area of the prospect. Depth-related changes in mineralogy include a decrease in illite and appearance and increase in quantity of chlorite with increasing depth, and the localisation of halloysite and interlayered illite-smectite in the shallow parts of some drill holes.

Jan 1, 2001

By T Arena

To maintain copper recoveries and maximise production at the Sepon Copper Operation it is crucial to control the amount of copper entering the leaching circuit. This requires close control of blending of the multiple ROM stockpiles to achieve the desired head grade. Grade variability in the ROM stockpiles can lead to significant variation in the processing plant copper feed grade.Head grade sampling from the milling circuit at Sepon is complicated due to milling in leach solution to preserve the water balance. Copper is present in both liquid and solid forms and copper in the added milling solution has to be accounted for. This leads to difficulties in manual head sampling which also introduces delays due to sample preparation and assay turnaround. On-stream analysis is complex because of the solution and solid copper and the need to account for recycled copper solution.This paper describes the complexity of feed grade management at Sepon and the application of on-belt analyser technology to assist in the control of copper metal throughput.

Aug 8, 2011

So many emergencies that crop up in mining necessitate a departure from ordinary methods that the writer has been led to illustrate a few of the examples that have come under his notice during a somewhat lengthy career; and as most of the methods illustrated are certainly outside the ordinary, it may be hoped that while to many they may convey little that is new, to the larger number some acceptable information may be gleaned whenever the occasion calls for it. Experience has shown that there can be no hard and fast rule in mine timbering that will fit the varying- necessities of different localities, and the engineer must divest his mind of all prejudices that his practice of any particular system or systems may have induced, and must direct his attention to the character of the local timber and its fitness or otherwise for the purpose he has in view. Fortunate indeed are the man and mine that can claim an abundance of good and cheap mining timber it simplifies, oftentimes, what would be, under unfavourable timber conditions, a difficult problem. In many parts of the States there is either none or at best a scrub if the latter, he has to either pigstye, balk, or bulkhead, if his ground will permit; if, not, and the necessary timber has to be imported, then some system of recovering his timber and using it over and over again may be possible. As an illustration of this, Fig-s. Nos. I and 2 show a method applied to the copper deposits of the LyellTharsis, Tasmania. The workings were wide; varying from 30 ft. to 50 ft., and the deposit a taIcose schist of fairly good...

Jan 1, 1902

ZINC concentrate, produced at Zeehan by flotation from Read Rosebery ore, is also dried and roasted at the same place for the production of a calcine suitable for use in the electrolytic zinc process at Risdon, Tasmania.DRYINGThe concentrate, dewatered to 12% moisture by an American filter, is fed into a dryer, the type of construction of which is similar to that of a duplex Edwards furnace. The dryer is 45 ft. long and 14 ft. wide, and has two rows of nine rabbles each, the two pairs nearest the firebox being watercooled.The longitudinal distance between rabble-centres is 4 ft. The rabbles are rotated at a speed of 3 r.p.m. by a I5-h.p. motor. Zinc concentrate is introduced by a screw feeder, consisting of two parallel-blade conveyors, revolving in opposite directions at aspeed of 31 r.p.m.Draft is supplied by a Sirocco fan, 15 in. intake, operated at 1340 r.p.m. by a 10-h.p. motor. The dust carried by the exit gases is removed in a wooden scrubbing tower, 3 ft. 6 in. x 4 ft. 6 in. x 27 ft. high, to which the fan delivers, and down which water issprayed.Wood (eucalyptus timber) is used as fuel, the consumption per ton of water evaporated being 0.55 :ton. Zinc concentrate from the dryer passed either to trucks for shipment or to Herreshoff furnaces. The portion for shipment is withdrawn at a point half-way down the furnace, being loaded on to a belt conveyor for transfer to railway trucks. The moisture at this point is 7% to 8%.

Jan 1, 1927

By J Missen, P Currie, J Bohan, D Clark

AGL is one of Australia’s leading integrated energy companies and the largest ASX listed owner, operator and developer of renewable energy and thermal generation in the country. AGL owns and operates the 2210 MW Loy Yang A power station and adjacent 30 Mt/a brown coalmine in the Latrobe Valley, Victoria. It also supplies coal to the nearby 1050 MW Loy Yang B power station owned by the GDF Suez (Engie)/Mitsui partnership. The mine is currently nearly 5 km long, more than 2 km wide at the operating face and up to 200 m deep. AGL employs a large workforce at Loy Yang and a substantial amount of services are performed on-site by contractors and consultants.GHD provides mine planning, earth sciences, civil/geotechnical engineering, dam surveillance, plant engineering and environmental services to AGL Loy Yang through an alliance framework. GHD is one of the world’s leading professional services companies operating in the global markets of water; energy and resources; environment; property and buildings; and transportation. In addition to GHD’s global footprint, the company also has a significant Victorian presence, including a permanent, well-resourced regional office in Traralgon, approximately 10 km from Loy Yang, as well as a permanent site office.A joint paper on the Loy Yang mine professional services alliance model was written for the AusIMM International Mine Management Conference in 2006 by Woods and Wood. Now ten years on, this paper provides an overview of the present relationship and arrangements, including the continued transformation of the alliance model and maturing of the relationship contract.These are challenging times, with increasing cost and regulatory pressure driving change in the broader energy and resources industry, and locally including both the mining and power sectors at Loy Yang. Flexible models to achieve a balance between internal personnel and access to key external skills, whilst achieving value for money and transparency, is increasingly critical. The right drivers and performance measures are essential, particularly when confronted with potential major technical and environmental risks (considering significant ground failure and fire events that have occurred elsewhere within the Latrobe Valley over the last decade) within a sector that is reducing costs and optimising production.This case study discusses the alliance status and changes, reasons behind adjustments and what the future is likely to hold. The paper also explores the validity of the original objectives and the extent to which they have been achieved. The philosophy of the alliance is to continue closely aligning the objectives of the two companies in the best interests of the Loy Yang site and immediate surrounds/stakeholders. Quality of service, costs, timeliness, health and safety (H&S) and some operational activities (aquifer depressurisation) remain important aspects and are reflected in key indicators for which performance is measured.CITATION:Clark, D, Bohan, J, Currie, P and Missen, J, 2016. AGL energy, Loy Yang and GHD – a further case study in alliancing: ten years on, in Proceedings International Mine Management Conference, pp 321-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016