Search Documents

By G W. Wilson, M Aubertin

A desulfurised tailings cover was installed at the Detour Lake Mine in Ontario, Canada, to reduce oxygen penetration into the underlying sulfidic tailings. The cover ranges from one to 1.5 m in thickness and was intended to maintain high water saturation to reduce oxygen diffusion and consume oxygen by oxidation of the residual sulfide minerals. The tailings impoundment was instrumented to measure climatic parameters, water levels and water content profiles within the tailings and single-layer cover. One year of monitoring data was collected. Additional tailings samples were obtained for geotechnical and geochemical characterisation. The average grain size of the cover material was found to be coarser than the underlying tailings. Monitoring also indicated that air entry values of the cover material were lower than the tailings. Numerical modelling was conducted on the cover to predict water content profiles under varying climate conditions together with the depth of oxygen penetration and diffusive oxygen fluxes. Estimates of the diffusion coefficient and kinetic oxidation rates from field data compared well with values obtained by laboratory measurements. Numerical simulations indicate water saturations of less than 85 per cent can be expected under varying climate conditions. Predicted oxygen flux rates through the desulfurised cover over tailings with high acid potential indicate low flux rates reaching these tailings due to either consumption of oxygen by residual sulfur within the cover or saturation of the underlying tailings.

Jan 1, 2003

By S Roberston, G Batt, R Shanahan, B Shah, A Trench, H Bromfield

The geographic imperative of ore systems leaves mining, more so than virtually any other aspect of modern industry, heavily dependent on obtaining and maintaining social licence to operate. A prospective miner cannot arbitrarily walk away from a deposit in search of more favourable community perceptions – concentrations of mineral endowment represent highly specific and fixed elements of the landscape, and their development and extraction thus requires the acceptance and trust of a specific network of landholders and stakeholders, sometimes with diverse and even competing interests in the development and use of the local environment. Weakness or absence of such social licence can bring added costs and complexity to developing and operating a mine – and in extreme cases even result in project failure. Because it must be maintained throughout the life of a project, such social risk becomes a substantial part of overall project risk profile, particularly during routine operations once initial technical and development risks have been largely resolved.CITATION: Bromfield, H, Roberston, S, Shah, B, Shanahan, R, Trench, A and Batt, G, 2018. On equitable distribution of mining wealth and the social licence to operate imperative – an African case study, in Proceedings Complex Orebodies Conference 2018, pp 6–7 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Last evening, in Auckland, I heard the Chairman of Heinz US, Dr Tony O'Reilly (who, in addition to Heinz's ownership of our largest food processor, also has substantial personal investments in this country), advocate New Zealand as a 'regional corporate capital'.   Why would someone like Dr O'Reilly hold that view? No doubt, as one of Ireland's great rugby players of the 50s and 60s, he admires at least one thing that we do very well (confirmed again in Dublin over the past weekend). But that's not sufficient to support such a view.   He cited many reasons for preferring New Zealand over, say, Sydney, Australia, calling this 'the most rational in which to locate [an] international headquarters', including û +         we have no capital gains tax; +         a more 'pro-business environment'; +         a 'first class' legal and banking system; and +         a 'simple political system'.   I can find no better 'text for today's address.

Jan 1, 1997

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

The plant and processing site at Porgera has been built on a levelled mudstone ridge about lkm E of the mine. Excavation of 7xl06m3 of soil and rock was necessary to achieve the required area. The exposed mudstone belongs to the Chico Formation and is weak, sheared and readily breaks down by slaking upon exposure. Tectonic uplift and subsequent erosion have produced the present landscape of narrow bedrock ridges, with deep colluvium in the incised valleys. The deep excavation to a maximum of 60m, has rapidly unloaded the mudstone, and subsequent stress relief has caused rebound and dilation of the material. The processes of pore pressure equilibration, softening, progressive failure and loosening, combine to deteriorate the newly exposed rock mass. These processes are commonly associated with pre-existing shear surfaces, fissures and a

Jan 1, 1991

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By S Sabanov

Supplementary sampling of particulate mass concentration, the number concentration and the average particle diameter of nanoparticles using a TSI Dust-Trak DRX Aerosol Monitor, Naneos Partector 2 has been conducted. The aim of this study was to evaluate suitability of the instrument for long-term monitoring of diesel particulate matter (DPM) at conditions of polymetallic mines. Sampling was conducted in an area of the active ore heading, requiring the use of a diesel-powered face haul-age loader R1700 and a mine truck Caterpillar AD-45. The sampling was done for 126 minutes at a distance of 30 metres from the mine face. Results of this field work can be used to expand the sampling program to other mines. Expected outcomes of this study are to develop costeffective DPM control strategies, improve mine ventilation, and protect mineworkers’ health.

Oct 12, 2022

By K George

The Dugald River lead-zinc-silver deposit is located approximately 60 km north-west of Cloncurry and 87 km north-east of Mount Isa. The development project is expected to turn operational in 2018. The resource is estimated to contain 61.1 Mt at 12.6 per cent zinc, 1.9 per cent lead and 34 g/t silver, with a projected mine life of 25 years. The evolution from exploration project to development project has presented multiple challenges for the technical team. Understanding and modelling the structural complexity of the deposit has been one of these challenges.Historically fault zones were logged as a lithology, with structural measurements recorded in a separate database table. When underground drill programs and development commenced in late 2012, it was recognised the deposit was more structurally complex than had been modelled. The extensive number of fault zone lithologies in core logging, made it difficult to identify fault trends and model faults in 3D software packages.In 2014, a structural project was conducted to produce a fault model for the deposit. The project highlighted that by logging the faults as a lithology, a shortage of fault characteristics was being recorded. Additionally, structural information could not be filtered to identify different fault sets due to the lack of information available to filter on. One of the major outcomes of the study was to change the methodology for the structural logging of drill core.Faults are now logged in a separate structural log. The structural log collects two types of information: interval data and point data. The interval data represents the damage zone of the fault in the surrounding rock and the point data the plane of movement for the fault. The faults are further characterised by their intensity on a scale of one to five, the type of fault structure (fault breccia, fault vein etc), the minerals present on the fault surface and structural measurements when available.The new data set allows fault data to be filtered based on fault characteristics, making implicit and explicit modelling of the faults more timely and accurate. The data set can be used to produce fault wireframes as single surfaces from the point data or hanging wall and footwall surfaces from the interval data. The logging method and how its applied in fault modelling form the focus of this paper.CITATION:George, K, 2017. A new approach to logging and modelling faults at the Dugald River Pb-Zn-Ag deposit, North West Queensland, in Proceedings Tenth International Mining Geology Conference 2017, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By A J. Ryan

The Ernest Henry copper-gold Mineral Resource is the major asset heldby Ernest Henry Mining Pty Ltd, comprising A$6.4 billion of containedmetal. The case history presented below describing the evolution andevaluation of this resource generally observes best industry practice and is a good example of effective due diligence in the resource delineation and estimation process. Early reconciliation data from mine production confirms the accuracy and validity of the resource estimate, providing valuable assurance to the mine owners.

Jan 1, 1998

A study was conducted to evaluate the effectiveness of the three types of sample grinders routinely used in the mining industry for the sample preparation of gold ores with particular emphasis placed on testing their capacity to produce a representative assay sample of coarse gold ores. The grinders used in this study are the Labtechnics LM5, the Mixermill 4010 ringmill and the Keegor vertical spindle pulveriser, commonly called a Keegormill. The study was based on the preparation of samples from two sources of known coarse gold ore, the Union Reefs Gold Mine and the Brocks Creek Gold Mine in the Pine Creek region of the Northern Territory of Australia, and a fine gold ore which was from the Macraes Gold Mine in New Zealand. The Union Reefs Mine contains visible coarse gold with 30 per cent to 40 per cent of the gold in the plus 75 μm fraction of milled ore. Discreet particles up to 5 mm have been recorded, Hellsten (1994). Union Reefs Gold Mine recovers 40 per cent of its bullion production through a gravity circuit, Riches (1997). Brocks Creek ore contains visible coarse gold with gravity bullion production fluctuating between 50 per cent and 65 per cent, depending on the mill feed. Average gravity bullion production from the Brocks Creek Mine is 55 per cent, Wilke (1997). The average gold grain size of Macraes Mine ore is 20 μm with 40 per cent of the gold in sub 10 μm particles. No gravity bullion is produced from the Macraes Mine, O'Keefe (1997). The testwork demonstrated conclusively that it is possible to prepare a representative sample for assay, of a coarse gold ore, when a Keegormill is used to pulverise the sample to a nominal 100 μm particle size (90 per cent passing a 100 μm screen by wet sieving). Both the Mixermill and the Labtechnics LM5 failed to prepare a representative sample, even when ground to a nominal 75 μm particle size.

Jan 1, 1998

By D Kentwell

A resource model serves two main purposes depending on the stage of a project. The first is to provide an early indication of likely tonnages and grades at certain cut-offs so that decisions can be made on whether continued spending on the project is justified. The second is to provide a basis for mine planning, feasibility studies and reserves. Resource models are not designed for selection of actual blocks in the ground for processing. This is the purpose of a grade control model, which is created at a stage beyond both resources and reserves.Inferred, Indicated and Measured Resources contain different levels of uncertainty with respect to the accuracy of the resulting grade and tonnage curves. These uncertainties arise from three broad areas: quality of information, geological assumptions and estimation technique. This paper focuses on known problems with the ordinary kriging (OK) estimation technique. Resource estimates often produce smoothed block grade distributions with much lower block grade variability than true selective mining unit (SMU) block grade distributions. There are two main factors that are involved in this smoothing. Firstly, where the block size used for estimation is larger than the SMU block size, this will smooth the block grade distribution and move the grade and tonnage curves away from the true SMU block grade and tonnage curves. Secondly, and less well recognised, is that smoothing is inherent in the OK estimator. This also moves the grade and tonnage curves away from the true SMU grade and tonnage curves, even when the estimate is done at the SMU block size. There are a number of techniques, such as simulation, uniform conditioning and degraded search neighbourhoods that can provide a better approximation of the true SMU block grade and tonnage curves at the expense of individual block accuracy.This paper aims to explore the extent to which OK resource estimates designed to maximise individual block accuracy can differ from (an estimate of) the true resource at SMU block size in terms of grade and tonnage curves. The differences at economic cut-offs and above are examined. In some cases these differences are significant. Both the OK estimation technique and block size play a part in the differences observed. To do this we will examine a number of commodities and deposit types using real project data.The conclusion is that the current industry standard default practice of targeting maximum individual block accuracy (conditional unbiasedness) using OK at resource stage, without consideration or evaluation of the extent of associated smoothing at SMU scale, can lead to significant errors in fundamental mine planning decisions. This then has implications for resource classification if the classifications are based heavily on the OK quality without consideration of the true SMU distribution.CITATION:Kentwell, D, 2014. Aligning resource estimates with mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By B Murphy, T Mattsson, R Crosbie, T Maksimainen

"An Outotec e500 TankCell, with 500 m³ of actual flotation volume, was commissioned at the Kevitsa Cu-Ni-PGE concentrator in northern Finland during 2014. This flotation cell was implemented at the head of the existing copper circuit as the first Cu rougher flotation cell. This was the first flotation cell of this size to be run under production conditions by any supplier anywhere in the world.The cell has been in continuous operation since start-up in October 2014 and has provided improvements in metallurgical performance at very low specific power consumption. On average, the cell has recovered 71 per cent of copper contained in the 0.37 per cent Cu flotation feed at a concentrate grade of 17 per cent Cu. The specific power consumption for the cell (excluding blower power) is typically around 0.4 kW/m³.After start-up, the impeller speed and superficial gas velocity were varied and the impact on metallurgical performance measured. In this paper a review of the cell operation at Kevitsa is given. Furthermore, the impact of mixing and gas dispersion on metallurgical performance is presented.Citation:Crosbie, R, Mattsson, T, Murphy, B and Maksimainen, T, 2016. Metallurgical Performance of Outotec's e500 TankCell at the Kevitsa Cu-Ni-PGE Concentrator, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Snowden D. V, Standing C. A, Ryba A, Bywater A

McKinnons open pit gold mine, located within the Cobar Basin in New South Wales, is characterised by complex mineralisation controlled by the intersection of steep faults in the hinge zone of an anticline. Resource estimation using indicator variography and indicator kriging was based on RC drilling on 25 in sections together with grade control RC drilling on 12 in by 12 in and 6 m by 6 in patterns. Rigorous sampling and checking procedures were used to verify the reliability of the drill hole data. Blast hole data was used to assist grade control in defining ore block boundaries.

Jan 1, 1997

By S T. Jarvis

Colliery spoil is the major constituent of colliery spoil ærockpasteÆ which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpaste are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising infilling a 6600 m3 section of an abandoned mine was conducted prior to the infilling of the Littleton Street Mine which had a volume of about 500 000 m3. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully used for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over 11 mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

A GREAT deal of attention has lately been given to the discussion as to the education required for engineers, and especially for mining engineers. The Institute of Civil Engineers has had a committee's report on it which has come to some interesting and valuable conclusions.The Institute of Mining and Metallurgy had a few years back a very long discussion on the subject, and the subject appears to be one of perennial interest to similar societies. Two recent addresses by Prof. Kernot, as president of the Victorian Instituteof Civil Engineers, are among the most interesting and practical of the contributions to the discussion. Engineers seem to feel either that the coming generation has not the same capacity to benefit by the training that has made themselves what they are, or that such training has turned out in themselves inefficient men, and that they must consequently struggle to obtain a better one for their successors. For not only is there a desire to extend existing instruction to cover the advances of science, but there seems to be a general desire also to make a completely radical change in the methods.It is not necessary to observe that education does not mean the imparting and acquiring of information, but rather the cultivation of the faculties so that the best use can be made of them and of any information acquired. For instance, a man is not educated who has by heart his lectures and the contents of his text-books, but that man is who remembers little of the actual wording of his text-books, but is able to find anything required in them...

Jan 1, 1909

Since 1865 when Congress moved to create a Federal Mining Bureau, successive legislations have given rise to the current '!Federal Coal Mine Health and Safety Act, 1969. Coal beds from 22 feet to 20 feet thick are mined under covers from 50 to 2800 feet with full and partial pillar recovery equally popular and accounting for a total of 54% of the mines. Pillar recovery and roof support practices vary, and each operator must submit an overall roof control plan (within specific guidelines) for approval before undertaking any development. The guidelines relate to dimensions of openings, details of support, sequence of extraction, limits of extraction and caving details. Experienced and professional staff of M.E.S.A. provide roof control plans and make inspections and grant-approvals of principles of support and minimum support in pillar extraction, with provision for modifications with time. Guidance is given with training programmes and standards of supervision. All of these aspects are approached in the spirit of the Congress declaration that the first priority and concern must be the health and safety of the miner.

Jan 1, 1974

By G Wyartt

Systems such as Davey Bickford’s Daveytronic® SP blast initiation system and electronic detonators have been an integral part of drill and blast activities in Australia for over a decade, with the significant benefits of electronic blasting well documented. Since 2010 the Multiblast feature has been commercially available, which enables eight individual blast patterns (up to 1500 detonators each) to be blasted in the same firing window. Synchroblast has been in active operation since 2012, which allows a blast of up to 4500 detonators – either as a single blast pattern, or several smaller adjacent blast patterns – to be reliably initiated.Multiblast manages blasts separately but concurrently, allowing all blasts to conduct prefiring checks simultaneously from the firing point utilising only one remote blasting unit. Each blast can be selected and fired individually, in a sequence determined by the operator by scrolling through the colour display. Synchroblast automatically detects the blasting configuration, and manages all detonators as a single blast pattern. This simplifies the design and blasting processes for the mining operation.Multiblast and Synchroblast are routinely employed throughout Australia and globally in both open cut and underground operations, enabling optimal productivity due to increased blast volume and reduced operational downtime associated with blasting events.A number of case studies will be presented in this paper, detailing various mining operations that are consistently blasting in excess of 2500 detonators per blasting event as a part of standard drill and blast operations. Blasts over 3000 detonators are becoming more frequent as mine planning departments adapt to this operational capability and flexibility.CITATION:Wyartt, G, 2017. Multi and Synchroblasting – maximising operational productivity, in Proceedings Iron Ore 2017, pp 631–634 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

As mines become deeper, the problems of heat in the workplacebecome more acute. An important response from the industry hasbeen the widespread adoption of microclimate cooling such asair-conditioned cabins. However, not all work in mines can becompleted from inside an air-conditioned cabin, and in any event,it is still important to keep the ambient air in the mine outside ofany microclimate to a safe temperature. An important method forbringing workplace temperatures under control is the appropriateuse of refrigeration. The application of refrigeration inmechanised mines has been recently described (Brake, 2001;Brake and Fulker, 2000). This paper provides an overview ofsome of the important engineering considerations in thespecification and selection of mine refrigeration plants. Thepurpose is to provide a basic understanding of refrigerationprinciples, practices, terminology, hazards and opportunities formining engineers or other personnel who may need to beinvolved in the introduction of refrigeration onto a mine site.

Jan 1, 2001

My purpose here today is to introduce an element of democracy into this seminar. In my experience, the mines of Australia can be divided into two categories; those that pay and those that don't. As far as I can ascertain, every other paper being delivered at this seminar concerns mines which come into the first category, or at any rate are close enough to it for the promoters to be able to afford an expert's valuation.

Jan 1, 1989