Search Documents

An Investigation into the Flotation Behaviour of Pyrrhotite Present in the Merensky Orebody

Sep 13, 2010

By L D. Queen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Tifalmin porphyry copper district is located in the Star Mountains roughly 35 km north-east of the Ok Tedi mine. The district is a cluster of temporally and geochemically related porphyry copper deposits and their associated skarns. It covers an area of roughly 10 × 6 km and comprises at least three intrusions (Olgal, Futik and Kum Kom) where drilling has demonstrated the presence of porphyry copper mineralisation, and another three intrusions (Rattatat, Unfin and Pad 48) where porphyry copper mineralisation is strongly suggested by surface investigations and geochemical or geophysical signatures.Copper and gold mineralisation was first discovered in the area in the 1960s as part of the regional exploration program by Kennecott that located Ok Tedi. The mineralisation is associated with poly-phase porphyritic diorites, quartz diorites and tonalites that intrude the Upper Eocene to Middle Miocene Darai limestone and underlying Cretaceous to Eocene Feing Group. Radiometric K-Ar and U-Pb zircon ages cluster between 4 and 2 Ma for both the mineralised and post-mineral intrusions. In addition to porphyry-type mineralisation, variable amounts of calc-silicate and/or magnetite skarn occur near the contact of most of the intrusions. Mineralisation in the Olgal and Futik porphyries occurs as chalcopyrite replacement of mafic minerals and in a stockwork of micro-veinlets. Mineralisation mostly occurs in the intrusions but is also observed in hornfelsed siltstones and sandstones of the Feing Group on the southern margin of the Olgal intrusive body. Quartz veining is uncommon. Secondary magnetite is commonly associated with the highest copper and gold grades. Sericitic alteration is most prominent in the mineralised hornfels. Structurally, the area is dominated by syn- to post-mineralisation thrusting from the north. At least one of the deposits (Olgal) appears to be truncated at depth by a thrust fault.CITATION:Queen, L D, 2015. The Tifalmin porphyry copper gold district, Star Mountains, Western Papua New Guinea , in Proceedings PACRIM 2015 Congress, pp 357–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The fundamental features of the Cable Belt Conveyor are described. It consists of independent wire ropes which take the transmission load, and a special reinforced rubber belt which acts 'only as carrier of material. The first cable belt installation in Scotland is described briefly.A general description of this type of conveyor is followed by details of the rubber belt construction and the method of joining sections of belt. The drive unit, the tensioning arrangements and the power requirements are outlined.Applications of the cable belt conveyor are 'dealt with and its advantages summarized.INTRODUCTIONThe cable belt conveyor, as its name implies is a conveyor composed of steel wire ropes and a rubber belt, in which the ropes serve as transmission members, and the belt merely as a carrier of materials.Over the years it has been the ambition of engineers connected with the belt conveyor industry to develop a conveyor that would use the high tensile strength of wire ropes to transmit the stresses involved in the driving of large capacity belt conveyors. Different lines of approach have been adopted in the United States of America and in Britain. In the United States the method adopted was to introduce a large number of flexible steel cables into the rubber belt itself, in the form of a closely packed layer arranged across the full width of the belt. These small cables are packed in a nylon filled duck envelope which is incorporated in the rubber belt. This is commonly known as the steel corded conveyor belt. In Britain, a Scottish firm developed a rubber belt conveyor in which full advantage was taken of the high tensile features of wire rope, without embodying or moulding the wire rope into the rubber belt, so that the two wire ropes and the rubber...

Jan 1, 1957

By B Stewart

The SRS-1200 concept came about following the recommendations from the Board of Inquiry into the 1994 Moura No 2 mine disaster with the aim of having a system to remove personnel from an unsafe environment underground via a shaft where no other means of escape is possible. It is a mobile rescue unit that utilises a winding system to operate a man cage. It can descend the cage up to 1200 m into a vertical shaft. This operation is managed from the winder control compartment located on the non-driver side at the rear of the vehicle.

May 5, 2022

If an orebody has been drilled to achieve some level of regulatory compliance, then a number of associated geological databases will exist, representing 10 000 to 100 000 m plus of core intervals. The databases usually contain data about assays, lithology, mineralisation and geophysical attributes. They will also include location information such as collar positions and downhole surveys. Obviously this data is collected by geologists for, predominantly, geologists and mining engineers. However, from a process design viewpoint process engineers usually ignore the geology where possible and rely on a small number of metallurgical test samples. Typically these test samples are sourced from convenient and available cores or from a small number of specially drilled metallurgical holes. One of the worst instances known to the author was the design of a SAG mill using only two SAG specific test results (one for each of the major ore types) while, geologically, the orebody was defined by more than 30 000 m of drilling. This paper sets out a philosophy to maximise the use of the geological data, both for process design and in preparation for the commissioning phase of projects. Geological data is used in the identification of preferred locations for metallurgical test samples, for checking the metallurgical validity of the geological ore-type definitions, where necessary developing new ore-type definitions (geometallurgical domains) and developing mathematical relationships for the estimation of important metallurgical factors across the geological database. If the estimation of factors (for example ore competence) is considered reliable enough then there is also the possibility of feeding calculated data back into the block modelling process to allow the generation of metallurgically relevant outputs in the mine plans.

Jan 1, 2007

By Wharton P, Voigt R

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

The Department of Mineral Resources is the lead agency in mine site environment management and control inNew South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.  

Jan 1, 1995

By A Brzovic, E Córdova

In an underground mine, different mining activities such as undercutting and cave progression generate redistribution in the present in situ stress field, and these changes are represented in the rock mass through induced seismicity.In order to study and analyse the induced seismicity generated in El Teniente, a block model was developed to account for the dissipated seismic energy through different areas of the mine from 1992 to 2015. More than 2.1 million seismic events were unified and classified in 3D in order to be used for the interpolations. The resultant model variables account for the accumulated energy releases in a monthly time resolution, and provide the ability to intersect different 3D entities with the stored information in the blocks, and estimate the energy evolution inside these entities.The generated model was used to analyse the geotechnical variables that determine the seismic response for the rock mass in the mine, such as geometry and direction of advance of the undercut fronts, lithological domains, and to study the ‘work’ the rock mass needed to go through in order to generate caving in areas with different stress settings.A specific area of the mine under high-stress conditions was analysed by studying the seismic energy associated with two subsidence caves interacting around the project, the modelled lithology. Using the same approach two adjacent projects are analysed to understand the released energy from the rock mass based on different stress and geotechnical settings for each project.CITATION:Córdova, E, Brzovic, A and González, R, 2016. Analysis of progressive seismicity and its correlation with geotechnical variables at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 835–844 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Ritter K-C, Sturgul J. R, Filess T

The proposed Lihir open pit gold mine is located on Lihir Island in New Ireland Province, Papua New Guinea. The mine will be located within a volcanic caldera, part of which forms the adjacent Luise Harbour. Kennecott Corporation started engineering design work in 1988 and ended in 1993 when a Feasibility Report was submitted to the Papua New Guinea government by RTZ/Kennecott. The project will be managed by the Lihir Management Company. The mining operation will produce approximately 350 Mt of waste and 62 Mt of low-grade ore over the life of open pit mining. Landforms and traditional land use by Lihirians preclude storing mine waste and some of the low-grade ore on land close to the mine site. The mine waste will be composed of hard rock and soft soild like material which cannot be safely used to construct large land waste repositories by truck dumping. Submarine disposal by bottom discharging barges is the only safe disposal method. The barges will also be required to construct a waste platform along the shore for stockpiling low-grade ore. A simulation model of the waste handling system was written in GPSS/H¦ to assist engineers in selecting the optimum size and quantity of barges and loading docks by analysing the interaction between excavators, trucks and barges. The simulation model was written in enough details to model the various functions that will be encountered during mining. Input parameters allowed for variations in the size and number of trucks, shovels, barges and loading docks. Variations in loading, hauling, and dumping times were from user specified distributions. In order to visualise the interaction between the components of the waste mining operation, the simulation was animated using Proof AnimationT""'. It is believed that this is the first application of an animated simulation study for a mine still in the planning stages.

Jan 1, 1995

By Thomas MJ

The Cannington silver-lead-zinc deposit is located at latitude 21¦ 52' 9" South, longitude 140¦ 55' 10"" East, on the south-eastern margin of the Proterozoic Mount Isa Block (Figure 1), 135 kilometres south-east of Cloncurry. Access is via a graded shire road for 80 kilometres south from the small pastoral community of McKinlay.REGIONALThe deposit is hosted by the Proterozoic Soldiers Cap Group within the Mount Isa Block Eastern Succession. South of the Cloncurry Beardsmore et al (1988) have grouped part of the Eastern Succession stratigraphy intothe Fullarton River and Soldiers Cap groups (1760-1740 million years) which together make up the Maronan Super Group. This is an apparently conformable sequence 10 kilometres thick and consists of metamorphosed sediments and volcanics with intrusive amphibolite bodies.The Maronan Super Group has experienced a complex history of deformation with up to six events having been recognized. The stratigraphy trends broadly north-south and is predominantly characterized by tight, upright isoclinal fold structures.

Jan 1, 1993

By M, C A. RosiFre, R C. Figueiredo e Silva

Jaspilites and underlying basalt contacts of the Archaean volcano- sedimentary Grpo Parß Group, Carajßs, host giant iron mineralisation in the ~100-km long, E-W trending Carajßs fold. Preliminary, unpublished geochronological data point to a Palaeoproterozoic mineralisation event. Geochemically, jaspilites are typical volcanogenic banded iron formations. Basalts exhibit evidence of spilitic seawater interaction. Iron-associated hydrothermal alteration of mafic rocks was induced by fluid infiltration in amygdales, with development of chlorite- and hematite-dominated zones. In the case of jaspilites, iron mineralisation encompasses: partial replacement of jaspilitic microcrystalline hematite by blasts of martitic magnetite; jasper recrystallisation, producing fine-grained, hematite-free granoblastic quartz; martite recrystallisation, forming lobate¦subhedral hematite; pervasive porosity development by quartz-chert leaching; incipient cavity filling by microlamellar hematite; and advanced filling by coarser, euhedral and comb-textured, tabular- shaped hematite.Peak hydrothermal ore textures indicate typical epithermal-crust conditions, supported by preliminary fluid-inclusion calculations at 160 - 200¦C. Such temperatures and extreme fluid-to-rock ratios during alteration must have exceeded the ambient metamorphic conditions, with the infiltrating fluid relatively hot and capable of leaching SiO2. Therefore, mineralisation developed over exhumed, Archaean, brittly deformed rocks, with mineral associations representative of very low- to low-grade metamorphism. Considering that chlorite (¦talc) abounds in mafic rocks; hydrothermal albite is developed; dolomite fills veins and vugs; the typical rare-earth-element (REE) pattern of jaspilites is significantly modified in higher-grade hard hematite ores (higher LREE); pyrite, copper sulfide minerals and rare gold occur in association with carbonate-quartz-rich alteration zones, it is suggested that an alkaline, H2O-Fe-CO2 mineralising fluid dominated, also containing species like S¦Cu¦Au. Peak-mineralising conditions are likely to have resulted from a single, evolving fluid, via incipient- through advanced-stage alteration phases. The porous, high-grade soft hematite-type ore (SH), rich in microlamellar and anhedral hematite, must have derived from interaction with this relatively hot SiO2-leaching fluid, whereas the high-grade massive hard hematite-type ore (MH) developed due to closer fluid-rock temperature equilibrium conditions, attained by mineral reactions, with relative increase in the Fe/Σcations ratios allowing the precipitation of subhedral-tabular hematite that partially cements the soft-hematite ore. SH and MH hematite ore types must thus reflect intermediate and high fluid:rock ratios, respectively. Since the N5 deposit is to date understood to contain the largest amount of the MH ore, its units are interpreted as the loci of the highest fluid:rock ratios in the district. Preliminary mineralogical information regarding the S11 deposit of the Serra Sul (south range) implies higher-temperature conditions. The near-equant grain size and the granoblastic intergrain relationship, coupled with the presence of riebeckite, augitic pyroxene and garnet, suggest hornfels textures. The data collected, though still relatively sparse, permit the speculation that the immense driving force for the Carajßs world-class iron deposits was a relatively shallow, igneous-related hydrothermal system. If such a model is correct, then the Carajßs Palaeoproterozoic iron deposits could represent an end-member of the iron oxide-copper-gold hydrothermal system in the province.

Jan 1, 2005

Cyclone Process for Heavy Metals Decontamination of Sediments

Sep 13, 2010

The disadvantages of the present zinc producing methods, RLE and ISP, are high energy consumption and environmental problems. Therefore, efforts have been directed in Outokumpu Zinc towards the development of alternate routes. One interesting pyrometallurgical process to produce zinc is to inject zinc calcine together with a solid reductant into molten iron, saturated with carbon. This process has been studied by thermodynamic calculations, laboratory tests and mini-pilot test runs at Outokumpu Research Oy, Pori, Finland. The results of these tests are presented and discussed in this paper. The mini-pilot tests demonstrated that over 97 per cent evaporation of the zinc was possible using a reactive coal dust as the reducing agent. The recovery of zinc in the metal phase was at best 88 per cent of input zinc, but only part reported in molten lead in the splash condenser. The final metallic zinc contained at best 98 per cent Zn, the main impurities being dissolved lead and coal carried along with the flue dusts.

Jan 1, 1993

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

By Okabe K

Development in the theory and practice of hearth drainage is reviewed. Difficulties in the hearth drainage were re- newed during late sixties and early seventies when the size of a blast furnace and the top pressure were increased to result in the increase in tapping rate. Hearth drainage was improved first by in- creased number of tapping and then decreased tapping rate as it was predicted by theoretical studies. State of the coke bed in the hearth, e.g., 'floating' or 'sitting-on' the hearth bottom, is discussed in relation with influential factors on it and its influence on the furnace operation. The 'sitting-on' coke bed is to be aimed at for the consistent furnace working and for the lower rate of erosion of the hearth refractory. As the continuous tapping became standard prac- tice in large blast furnaces, the interest in the basic research renewed. Prospect of the further research including mathematical modelling of the hearth drainage is discussed.

Jan 1, 1981

By H Plewes, A Bur, L Murray, J Pottie

Water recovery from tailings for reuse in mineral processing is essential to operation of mines in the Atacama Desert of Chile. With annual rainfall of 5 mm, the prudent and efficient use of available water resources is a major issue for the Escondida Mine and other mines in the area. The Escondida Mine is located at an altitude of 3100 m, in a very arid, seismically active part of the Atacama Desert of northern Chile. The site is located about 170 km from the coastal city of Antofagasta. From 1994 to 2002, tailings were discharged into the Hamburgo Tailings Facility, which comprises a series of æpaddiesÆ located near the open pit and mill. Because water in the region is only obtainable from groundwater sources, the paddy system incorporated a number of design features with the aim to maximise water recovery from the tailings. As part of the recent mill expansion to 237 500 metric tonnes per day, a new tailings facility, the Laguna Seca Tailings Facility, projected to be one of the largest tailings facilities in the world, was commissioned in 2002. Extensive studies were conducted for the design of the new facility to predict water recovery from the conventional wet disposal of tailings. The predictions were calibrated against the performance of the Hamburgo Tailings Facility and subsequently re-calibrated against actual performance during the first year of operation at the Laguna Seca Tailings Facility. Initial operation of the Laguna Seca Facility was marked by a coincidental change in tailings characteristics from design, which highlighted the need for thoroughly understanding tailings behaviour during deposition, and the parameters and deposition techniques that could enhance water recovery. Systems have been put in place to manage the tailings deposition and respond to changes in key parameters such that water recovery targets can be reliably achieved. This paper describes the background studies that were conducted to evaluate evaporation and tailings behaviour, summarises the water balance and then presents some observations from the commissioning and start-up of the facility.

Jan 1, 2003

By G J. Lyman, S A. Tittlemier

International regulations exist to manage the concentrations of mycotoxins such as Ochratoxin A (OTA) and deoxynivalenol (DON) in grains and prevent health risks from excessive exposure to OTA and DON. Since the permitted levels of these mycotoxins are very low (existing maximum levels are in the range of 5 ppb for OTA and 1–2 ppm for DON), sampling for these mycotoxins is potentially challenging. Given that the distribution of infected kernels in a consignment of wheat can be highly heterogeneous, detection by current sampling methods is subject to a high variance. Furthermore, the concentrations of mycotoxins in individual kernels vary over orders of magnitude, intensifying the heterogeneity of the bulk grain.In these circumstances, there is much interest in developing sampling plans that inform regulatory agencies, and mitigate the risk of misclassifying grain shipments as compliant or non-compliant within the global grain trade, when correctly implemented.Experimental data from laboratory and field studies describing individual wheat kernel concentrations of OTA and DON were combined with experimental data describing the variance due to the analytical methods used for OTA and DON to calculate the sampling distribution for wheat having various levels of contamination. This work has focused on quantifying the heterogeneity of samples at the point of submission for analysis and within subsequent sample preparation to arrive at total sampling distributions that include uncertainties due to the intrinsic heterogeneity and the analytical uncertainties. The sampling uncertainty that relates to the difference between the primary sample analysis and the true lot analysis is not included as it has been dealt with elsewhere.CITATION:Lyman, G J and Tittlemier, S A, 2017. The sampling characteristics of grains contaminated by mycotoxins, in Proceedings Eighth World Conference on Sampling and Blending , pp 281–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By T Nixon

A common problem for many mines is insufficient total primary airflow or insufficient airflow in the correct places as the mine changes over its life. This has a number of impacts on the business operation and may result in the need for a major and unexpected capital upgrade of the system, cancellation of a planned production increase, reduction in production targets, increased operating costs, failure to provide contracted metals to customers or acceptance of substandard conditions in the workplace. In some cases, it can even result in premature closure of the mine. In recent times, higher metal prices have given an expected economic boost to many mines, potentially prolonging their life but simultaneously requiring the mine to develop to deeper depths or requiring assets such as shafts and fans to have their service life extended. Insufficient primary airflow is a particular problem in deeper mines as the ventilation circuits become longer, more convoluted, have higher shock losses and the actual airflow requirements increase due to a combination of leakage, dispersion of the workings and the problems of managing the additional heat loads due to higher virgin rock temperatures and autocompression. This paper discusses the reasons why mines experience unexpected shortfalls in primary ventilation capacity with its associated impacts on metal targets, profits and frequently on the health, safety and morale of the workforce, as well as its productivity.

Jan 1, 2008

By W C. Burton, J S. Kuszma, T O. Aspinall

The environmental impact of mining and evolving environmentallegislation has received increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental regulatory agencies and members of the public. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. There is thus the need to increase the base of knowledge on the existing practices of spoil dump design and rehabilitation. Efficient engineering design and systematic economic evaluation of spoil dump reshaping techniques for mine rehabilitation assists in maintaining the expected standards of environmental compliance. As part of the overall approach for effective engineering design ofspoil dumps, a comprehensive, computational and efficient tool isrequired for assessing the economics and productivity of existing spoil dump reshaping practices for efficient mine rehabilitation. Such a design tool is useful in linking current spoil dump environmental management practices with engineering design planning and economic impact evaluation. This paper identifies the processes for the economic impact evaluation for existing spoil dump reshaping practices and proposed final site dump designs. Selection of an efficient spoil dump design at optimum costs will ensure operational efficiency. A case study is presented identifying economic impact evaluation in earthmoving equipment selection and the costs involved for the reshaping of spoil dumps to that of varying final site designs.

Jan 1, 2000

By Green P. F

Apatite Fission Track Analysis (AFTA) is a thermal history reconstruction tool that enables determination of magnitude and timing of maximum paleotemperature and paleo-geothermal gradient at the time of maximum paleotemperatures. From this information, the amount of section missing at major unconfornities can be estimated and incorporated into basin models. The Gippsland Basin has a number of distinct problems that can be tackled using AFTA. 1. The nature of the regional break between the Late Cretaceous-Tertiary Latrobe Group and the underlying Early Cretaceous Strzelecki Group. 2. The tectonic history of the basement flanking the basin and its effect on sediment composition. 3. The age of igneous activity in the basin, as typified by the widespread basaltic plugs and dykes intruding the outcropping Strzelecki Group. Major uplift and erosion within, and adjacent to, the early Cretaceous rift basin in the Mid-Cretaceous, at -95 to 100 Ma, initially constrained the Latrobe Group depositional area to the central deep of the Gippsland Basin and provided an elevated source of quartz-rich detritus for the Latrobe Group reservoirs. This is in marked contrast to the preceding period in the early Cretaceous when contemporaneous volcanism dominated as a source of detritus, producing quartz-poor lithic sandstones, in which a host of attendant diagenetic reactions destroyed their reservoir potential. Initial uplift and erosion of the volcanogenic Strzelecki Group also occurred in the mid-Cretaceous as revealed by a number of distinct inversion structures, and erosion of this material will have locally provided very poor quality sand to the basal Latrobe Group.

Jan 1, 1992