Search Documents

By M Pratt

For up to 75 years large scale coal mining has been carried out within the Latrobe Valley region of Victoria. Withdrawal of groundwater from Tertiary aged sediments within the Latrobe Valley is essential to allow coal mining to proceed to depth. Water within the overburden layers, coal seams and interseams must be drained to avoid flooding during the mining process. The pressure in deeper aquifers must also be lowered to avoid floor heave, batter instability, and to maintain safe operating conditions as the mines develop in size and depth. The cost-effective management of the groundwater systems at and adjacent to the mining operations in the Latrobe Valley is essential to enable the efficient utilisation of the coal resource whilst minimising the environmental impact of this major industry in rural Victoria. Large-scale depressurisation and dewatering programs within the Latrobe Valley mines are managed through the use of detailed groundwater management plans. These incorporate:an extensive monitoring network which extends up to 60 kilometres from the mines; detailed mine scale and regional groundwater and hydrogeological models; and established operational procedures aimed at minimising capital and operational costs associated with the mine groundwater systems. Groundwater extraction system optimisation programs have been introduced into two of the mines with the aim of reducing extraction rates, improved risk management, and reducing operational costs by approximately whilst not compromising mine safety. This paper reviews the aquifer depressurisation and mine dewatering operations of the Latrobe Valley mines and illustrates the techniques utilised to ensure that high artesian pressures do not adversely impact on the mining operations.

Jan 1, 2003

By E Heath, F McDermott, S Turner, P van Calsteren

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath midocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and om, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100 000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50 000 years prior to eruption.

Jan 1, 1995

By S Graskoski

The allocation of boggers and trucks at Telfer’s sublevel cave mine is currently assigned by manual techniques, with decision-making primarily dependant on the judgement of the operators and mine control. Field observations indicate that allocation decisions could be improved by establishing a systematic approach to dispatch. An investigation into the current state of technology determined that no currently available solution would provide a tool to make optimal decisions for the Telfer dispatch challenge.In an underground sublevel cave (SLC) environment, the destination decision is fixed and the source is variable, so open pit and block cave solutions are not relevant. Newcrest underwent a development venture with an external vendor to develop a novel production dispatch algorithm and user-friendly software program to make allocation decisions in a systematic way with consideration given for the true complexity of the operation.This new production software, nicknamed Dingo (for Dispatch ‘n’ Go), is a smart way to assist forepersons and mine control operators in their day-to-day roles of planning shifts and allocating trucks and loaders to optimal locations during shifts.CITATION:S Graskoski, 2017. Dingo – an optimisation tool to solve complex short interval control at Telfer underground mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 261–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By N Khalili, J Zhao, G F. Zhao

Toppling failure of a jointed rock slope was studied by using the distinct lattice spring model (DLSM). Compared with the classical discrete element model, the DLSM has the advantages of free calibration of micro-mechanical parameters and easy to represent discontinuities, and is more computationally efficient. In this work, the DLSM was used to investigate the toppling failure of jointed rock slopes. The numerical simulation was verified against experimental data from a centrifuge model test on a jointed rock slope. Both the horizontal deformations and failure pattern observed in the centrifuge test were reasonably reproduced using the DLSM. Then, the mechanism of the flexural toppling failure was studied numerically by using a parameter analysis. Finally, some insights were derived that may be useful for practical engineering.CITATION:Zhao, G F, Khalili, N and Zhao, J, 2014. Application of the distinct lattice spring model on toppling failure of a jointed rock slope, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By A F. Cooper

Otago Schist in the Mount Patriarch, High Burn and Cameron Creek areas of northwest Otago grades from textural grade IIA in the east to textural grade III in the west. The entire region is of the actinolite-pumpellyite metamorphic facies. Lithologies in the area are interbedded turbidite sequences comprising pelite and psammite together with pebble conglomerate, greenschist and metachert horizons. The mineral assemblage of the schist is typically quartz-albite-epidote-actinolite-pumpellyite-chlorite-stilpnomelane-calcite. A good foliation is well defined in the area and is predominantly parallel to bedding, except in hinges of mesoscopic isoclinal folds. The structure of the area appears to be defined by a large southwest plunging isoclinal fold defined by bedding with a steeply dipping axial planar foliation. Kink folding and dextral strike-slip faulting in the area postdates the ductile phase of deformation. Pods of rhodonite, rhodochrosite, spessartine garnet, coombsite, caryopilite, Mnstilpnomelane and Ni-Cu-Zn sulphides were found in concordant metachert layers in the Mount Patriarch area. Metachert was also found in float in the Cameron Creek area. Malachite occurrences relating to copper mineralisation were also noted in a green metachert horizon on the eastern flank of Mount Patriarch. The coombsite, in only the third observation worldwide, is the most Fe-rich variety reported.

Jan 1, 2003

Roasting of zinc concentrate at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited, (E.Z.), is carried out in two fluid bed roasters capable of treating 450000 tonne/yr, or sufficient for the output of 220000 tonne of salable zinc. The furnaces were constructed by Lurgi, Australia, to the basic design developed by Vieille Montagne Company of Balen, Belgium. The advantages of fluid bed roasting include a higher metallurgical efficiency in sulphur oxidation from a feed which does not require any pre-grinding, mechanical reliabil- ity through the absence of any moving parts within the furnace and the capability of being scaled up to a large unit.

Jan 1, 1977

Contact Angle Measurements on Lignite Surface

Sep 13, 2010

The treatment plant at Martha Mine was upgraded from a nominal throughput of 110tph (O.93mtpa) to 150tph (1.25mtpa) late 1999. Post-upgrade performance did not meet expectations when treating either the competent primary ore or the clay-rich oxide ore.   ò Plant throughput is constrained by milling capacity when treating the competent primary ore. This is not an issue at present as current plant feed is oxide ore from the top of the open-pit, but will become so in future years as the pit deepens. To counter this future threat, ball mill power has been restored to 1100kW through modifications to the drive train. The addition of a crushing circuit may also be necessary.   ò Plant throughput was originally constrained by thickener and leach/adsorption tank issues when treating the oxide are. Changes to plant equipment and operations has seen the removal of these constraints and throughput on this material is no longer a problem.   The most significant issue facing plant staff at present is the high silver grade and its impact on gold recovery. These high grades impact upon recovery through losses caused by insufficient leach and adsorption capacity. To counter this, the geology, mining, and milling teams are working together to blend the high grade silver zones with lower grade ores - this is seen to be the quickest and most cost effective way to deal with the issue. The plant design has also been evaluated with a view to modifying it to cope with the higher silver grades. The viability of these modifications will depend on cost and time (that is, the length of time to implement any modifications versus the length of time to mine out the high silver zones).

Jan 1, 2001

The paper describes the geotechnical as- pects of design and construction of two 12 m diameter concrete lined tunnels from the start of design to completion of construction. Prob- lems occurred due to delay in supply of essen- tial rock support materials from overseas and alternative methods using locally available materials were developed. Several major rock- falls and rock movements occurred and remedial measures are outlined.

Jan 1, 1981

INCREASE OF THE OIL CONSUMPTIONIt is of the greatest interest to study the prospects open today for the petroleum industry by looking back to the past years.The' results for the past 15,years can be said. to be- satisfying; - the develop-ment of the petroleum industry has sustained a very fast tempo and the world consumption of energy has around the years 1960-1961 - reached aòpeak figure.Undoubtedly, the petroleum industry is the principal beneficiary of the growth of world, energy demand. For the caning years a slackening of the rate of expansion is'. likely to be expected; but will. not alter the general trend. This ' slackening of expansion may be explained, partly by a better use of the energy consumed and by the increased use of new types of energy, mainly natural gas.Although.the development of world energy demands follow structural and tech-nical modifications".,-At. can be foreseen, without any doubt, that the petroleum products. consumption. vri 11 be less affected than any other type of energy by this limited reduction in the rate of increase.

Jan 1, 1962

THE South Mine. owned by the Broken Hill South Limited, occupies mineral leases 7 and 8 on the Broken Hill lode. The ore reserves are 4,250,000 tons, and the ore hauled for the year ended June, 1930, was 387,000 tons, the total to date being 7,840,000.The mine, down to the 1070-ft. level, is naturally divided into two sections, the northern and southern ends. Ore extraction is practically completed in the northern end to this horizon, while the southern end is developed ready for a concentrated attack.Fig. 1 shows the state of the 8215-ft. level, after connection to the new shaft.The levels above and below to the 1070-ft. level are in a similar condition, while below the 1070-ft. level the stoping has been confined to the north end, but not completed. The south end on these levels is also partially developed.The ore at present is hauled up No. 1 shaft, which is centrally situated to the present workings. This shaft was put into use in 1909, and in 20 years has had approximately 5,000,000 tons of ore pulled through it.The company, having proved the existence of large ore-bodies in the southern end of the mine, decided to sink No. 7 shaft. This is a six-compartment frame-set shaft (see Fig. 2) equipped with two cages and two 5-ton skips, the remaining compartments being utilised for electric cables, pipes, and ladders. The surface arrangements will include a steel head frame, electric winders, and breaker station.

Jan 1, 1930

Gippsland has perhaps the most colourful history of exploration of any area in Australia. Hydrocarbons were first discovered in the Gippsland Basin in 1924 when a water well at Lakes Entrance encountered oil and gas shows. In 1942, the Commonwealth and Victorian Governments, in an effort to supplement a wartime oil shortage, sank a shaft near this well and produced 8000 barrels of low gravity oil up to 1956, when the field was abandoned. A total of 64 shallow wells had been drilled in the Lakes Entrance area by that time. Elsewhere in the onshore Gippsland Basin, 30 wells were drilled from 1925 to 1941. In 1960 BHP Ltd was granted an exploration permit covering much of the offshore area of the Gippsland Basin. Esso Australia Ltd joined BHP in 1964 and drilled the Barracouta-1 gas discovery in 1965. Since then over 100 exploration and appraisal wells have been drilled in the basin resulting in the discovery to date of some 3.6 billion barrels of recoverable oil and 8.8 trillion cubic feet of recoverable gas (Current remaining recoverable reserves are 906 million barrels of oil and 5.7 TCF of gas). Exploration in the offshore areas is actively continuing today and new discoveries are still being made.

Jan 1, 1992

By C Ross

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

Access roads for haulage, construction or maintenance purposes are discussed with particular attention being given to the un- sealed "all weather" form of construction for Off-Highway applications. The service conditions experienced by the surfaces used in these roads is examined. These conditions are discussed in terms of the conventional engineering properties used for natural gravel material selection. Experience gained during the construction of a pipeline access track is used to illustratE material selection guidelines based on geological input and an understanding of good construction practices. TMITDnIll IrTT Ohl In many Australian situations off-highway haulage by wheel or track supported vehicles is carried on unsealed, gravel roads. Although the unsealed gravel road is the back-bone of the rural road network in Australia, in general, traffic loadings are relatively low compared to the off-highway unsealed haulage road. The cost of the haulage/access road construction component is one important factor in project planning which needs careful consideration. It is no longer acceptable that the initial rough exploration track be gradually upgraded so that it will eventually carry construction and maintenance traffic safely and efficiently. Fatal accidents and

Jan 1, 1982

By R Paterson, A Christensen

The routine use of gravity gradiometry for the detection of orebodies with no outcrop is now being undertaken. The commodities and orebody styles range from banded iron ore formations to volcanogenic massive sulfide (VMS) style polymetallic deposits. This recent innovation of flying gravity gradiometry was pioneered by BHP Billiton and Lockheed Martin with the Falcon technology (Lee, 2001), and now two additional systems, also using Lockheed Martin instruments, are deployed. In South Africa, magnetic gradiometry is being developed and deployed with the same objectives in mind. In this case, a system from Institute of Photonic Technology (IPHT) is being used. The detectable wavelengths from such systems have decreased to less than 200 m in the last year, and it is expected in 2011 that wavelengths to less than 100 m, with anomaly signal strengths of less than 2 Eotvos for gravity gradiometry will be viable. The key to these advances lies in the improvements of processing software and geological modelling. In particular, methods using all the tensor components are starting to be routinely deployed to filter, level and grid the observed signal. These methods do, however, require full insight and understanding of the reference coordinate systems used by the various instrument designers and survey operators. The digital terrain models need also to be observed to an accuracy of better than 20 m cell sizes, using such techniques as Lidar. Then the terrain effects can be modelled. The topographic surface represents the largest and most proximal density contrast encountered in an airborne survey. Hence terrain effects can have significant impact on airborne gravity gradiometry data. A decorrelation of the terrain effect with the observed signal requires a method of best fitting with a regional surface density. A novel technique has been developed for this purpose. This technique uses a tensor algebra to estimate a density between 1 - 4 g/cc that explains the average observed signal. Armed with this result, the anomalous buried bodies can be revealed by subtraction.

Sep 26, 2011

During mapping in the Bijerkerno area (Fig. 1), well-preserved sedimentary structures were found at three separate localities. The structures are of four varieties, which are 1. small-scale cross-bedding (Fig. 2),2. convolute bedding (Fig. 3),3. minor scour and fill (Fig. 4), and4. flame structures.Ripple-marking is also doubtfully present.These structures are best preserved in what was...

Jan 1, 1971

By Bilbrey J. H

Land utitized duxting the past 45 yeans by the mining industty in the United States con all puxpos ez to tal4 neatly 4 million sexes. Ob this axes, 13 pexeent is used bon dL4posal ob bLne -sized mtinexal wastes dL4eaxded by one milling plants. These wastes, especi- ally the inactive taLeLng4 ponds, xequixe some type ob stabULzation to pxevent aix and watex pollution. Because these tailings ponds axe locat- ed undex wideey vaxyting etLmctLe conditions and thetix physical and chemi- cal ehaxactexti5tLes axe not constant, many methods have been developed by the Fedexal Buxeau ob Mines and oXhex inve4- ttigatoxs box 4tabLtLzLng taLtLngs. This papex detfnea.e4 the magnitude ob the pxoblemz associated with the xeelametLon ob milling plant wastes and discusses the vaxtious methods that have been developed and used. Data bxom selected Buxeau o4 Mines taboxato&y xeseaxch pxojects and a s.abAJLzetLon field txtial axe pxesen.ed.

Jan 1, 1976

IN previous discussions on the occurrence of gold in the Bendigo quartz reefs the opinion has been put forward that the gold shoots are primary concentrations in the quartz reefs during the period of vein-formation. The view has been based upon the constant features of the gold shoots in a large number of individual reefs, independent of their depth below the surface. These features include the mineral associations accompanying the gold, the appearance and association of the gold in the quartz, the similarity in all respects (excepting mineral content) between richly gold-bearing quartz and poor quartz, and the variations in mineral content in the reef apart from gold. The view has been supported by a relation of the gold shoots to faults, together with the dependence of the reefs on the existence of pre-mineral faulting. The secondary deposition of gold has only been observed in a few instances .associated with the younger monchiquite dykes, and is of no economic importance.

Jan 1, 1922

By Roddick F

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gipps- land mountains, the Long Tunnel Extended Gold Mining Company produced 13,695kg of gold, which at 1982 prices represents a value of about $140 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subse- quent occupants of the lease produced an addit- ional 160kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tourists.

Jan 1, 1982

By Corbett GJ

The Bulolo Graben represents an intra-arc rift formed by activa- tion of transfer structures in an extensional setting formed be- tween the eastern and western sectors of the New Guinea Origin. Crustal thinning has facilitated the emplacement of dacitic Edie porphyry intrusions, locally as flow dome complexes, phreatomagmatic (diatreme) breccias and the Bulolo ignimbrite/ agglomerate as an extrusive equivalent of the Edie Porphyry. Gold mineralization is localized along intra-graben structures, com- monly at the intersection with cross structures and occurs in sub- sidiary dilational fractures and not the localizing major structures. Gradations are apparent in the styles of mineralization according to the degree of erosion of the hydrothermal system. Hamata occurs as the deepest mineralization of the quartz-sul- phide style Wau, Hidden Valley, and Edie Creek are dominated by carbonate-base metal styles. Kerimenge grades from quartz sulphide through carbonate-base metal to epithermal mineraliza- tion, the latter style also being present in the periphery of Edie Creek. Here, pre-existing fractures of the Edie Creek Structural Corridor have been reactivated by movement on NS structures to form the ore-hosting dilatant lodes. Fluid flow may have been from the vicinity of the Nauti diatreme margin and along the vein System.

Jan 1, 1997