Search Documents

By P A. Williams, P Leverett

Many of the worldÆs stibnite deposits are found in orogenic zones and are mesothermal or epithermal in origin. They commonly occur near contacts between intrusives and metasediments. However, the spatial extent of anomalous Sb levels around such deposits is not well documented. This project has aimed to gain a better understanding of the mineralogy and geochemistry of Sb by deriving solubility and thermochemical data for some of the most common secondary Sb minerals. This has then been applied in field exploration for Sb ore deposits. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

In the new refinery, at the works of the Broken Hill Associated Smelters Proprietary Limited, situated at Port Pirie, South Australia, the refining routine is similar to that carried on in the old one in that bullion is progressively refined first for arsenic and antimony, then for copper and gold, then for silver, and finally for zinc. However, actual procedure differs in that each refining operation is now conducted continuously, whereas in the old refinery intermittent batch treatment was practised.The early experimental work was concerned solely with the development of the continuous desilverising process, which, in addition to continuous treatment, embraces the novel feature of conjugate solution formation with consequent production of a silver product relatively high in silver and low in lead.

Jan 1, 1932

By Hare G

The emphasis in Australia, until recently, has been on large scale mining methods with drive sizes in excess of 4.5 metres square and the acceptance of high dilution ratios, even when working in relatively narrow orebodies. The rising cost of extracting and treating the recovered ore and the lower prices available in the world markets has seen a growing trend to narrow mining methods.Traditionally narrow orebody mining has been carried out using hand held drilling methods and rail mounted boggers. Recent advances in mobile equipment now offers the operator of narrow method mines the opportunity to completely mechanise the mine from the drilling, through bogging to haulage, while maintaining minimal dilution in drive sizes to two metres wide or less.

Jan 1, 1993

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

The occurence of high silver values in the oxidised zone of the main lode at Broken Hill is well known as a large factor in achieving the early fame of Broken Hill, and the minerals of this zone form a long list, which has been tabulated by G Smith*, and includes...

Jan 1, 1926

In the exploration of an area proposed for the establishment of an underground colliery, consideration of all land and mining titles and consents has early priority. Environmental aspects have become more meaningful. Preliminary assessments of previous geological knowledge, together with new geological and geophysical data from surface investigations, condition the decision to proceed with costly diamond drilling programmes. Methods other than fully cored diamond drilling have a useful application in appropriate circumstances. Drilling exploration is conducted in stages of increasing density of-hole spacing to the point where, with holes at 1 km centres, reserves are categorized as measured. The programme is subject to constant review in the light of market changes.

Jan 1, 1976

By R M. Papini, A C. Araujo, A E. C Per

Flotation is an important process used in the concentration of iron ores. One of the challenges for process engineers is the low metallurgical recovery associated mainly with the fines fraction. In this work, the use of synthetic flocculants in iron ore reverse cationic flotation was investigated. The flocculants utilised were polyacrylamides of high molecular weight and different ionic degrees. Bench scale flotation tests were performed to compare the flotation performance with and without addition of polyacrylamides. It was observed that cationic and non-ionic polyacrylamides cause a significant increase in the metallurgical recovery. The anionic flocculant did not improve the flotation performance. An adverse effect was a slight increase in the silica content of the concentrate. Flotation with polyacrylamides was influenced by the hydrodynamic conditions of the pulp, such as agitation and the weight percentage of solids in the flocculant conditioning and flotation stages.

Jan 1, 2005

By Browning E. J

The application of conventional dust control systems in British Coal mines has considerably reduced the incidence of pneumoconiosis. A number of new techniques have been developed involving extraction close to the cutting heads of mining machines which will be capable of controlling airborne dust with the greater intensity of production necessary in the present economic climate.

Jan 1, 1988

By R McCarthy, P Hawke

FerrAus Ltd's Robertson Range and Davidson Creek Projects are located in the Hamersley Province about 100 km east of Newman, Western Australia. Significant iron mineralisation defined by an aggressive exploration program within the Marra Mamba Iron Formation is shallowly north dipping at Davidson Creek, and mainly shallowly east dipping at Robertson Range, forming part of a regional scale anticline with the granitic and greenstone basement of the Sylvania Inlier as its core. With minor exceptions, the stratigraphy is comparable with that seen in the main Hamersley Basin. Granite and greenstone basement rocks of the Sylvania Inlier are unconformably overlain by shales and volcanic rocks of the Fortescue Group. The overlying Hamersley Group is locally represented by interbedded chert, banded iron-formation (BIF) and shales of the Marra Mamba Iron Formation (Nammuldi, MacLeod and Mount Newman Members), and dolomites, cherts, BIF and shales of the Wittenoom Formation. Iron enrichment occurs predominantly in the Mount Newman Member, and to a lesser extent in the West Angela Member of the Wittenoom Formation. Enrichment varies from 20 - 30 m in thickness in elongate bodies up to 3 km in strike length, and generally thins down dip. At Davidson Creek iron mineralisation is a haematite-goethite-ochreous goethite assemblage, while at Robertson Range this assemblage is consistently overprinted by a later, goethitic alteration related to 'hardcap' weathering. Near surface hardcap alteration in both project areas comprises more siliceous, aluminous and vitreous goethite. Initial exploration completed by Rio Tinto Exploration between 1999 and 2001 indicated the potential for about 20 Mt of iron mineralisation at Robertson Range. Since 2005 a detailed exploration program undertaken by Australian Manganese Pty Ltd (a wholly owned subsidiary of FerrAus Ltd) has defined a global indicated and inferred resource totaling 164.4 Mt at 58.6 per cent Fe (ASX: FRS 17 April 2009).

Jan 1, 2009

By Kawatra SK

The incentive to control coal flotation circuits arises because of disturbances, from plant operating practices and variations in feed coal characteristics, which result in large amounts of fine coal being lost in circuit tailings streams and lower grade concentrates being produced. Additionally, the flowrates and compositions of con-centrates and tailings streams can have significant effects on dewater-ing brocesses. A universal control strategy for these circuits cannot be developed. Rather, three major groups of variables must be con-sidered during strategy development: coal characteristics; circuit design and operating practice; and the variables selected to control the process. The second. and third groups-are discussed in this paper and examples from studies in operating plants are presented.

Jan 1, 1985

By D Craw

The Hyde Macraes Shear Zone is a mineralised low-angle shear within the Otago Schist traceable for ~30 km with a NW strike. It is been actively mined along 12km of this strike, producing >6 Moz of gold. The shear zone consists of greenschist facies rocks with a mineralogy only subtly different from that of the host schist. Pervasive fluid flow has occurred along grain boundaries and within microshears which have been enhanced by the deposition of hydrothermal graphite. We model the development of these microshears using a threedimensional numerical code. For an inhomogeneous initial rock with lithostatic fluid pressures and a dynamic permeability deformed under dextral non-coaxial flow, deformation is distributed into weak shear bands. Graphite deposition and associated reaction-softening has a dramatic effect on the development of model shear zones. Graphite is deposited into a shear band, weakening it and further localising the deformation into that shear band, producing an anastomosing and interconnected shear zone structure such as observed in the HMSZ. The degree of graphite precipitation and graphitic-induced weakening are varied in the models. More graphite precipitation with a low degree of reaction-softening results in more diffuse shear bands. In contrast less graphite deposition but with a high degree of reaction-softening more leads to the development of more focused shear bands. Graphite deposition has clearly controlled the formation of the HMSZ structure, and is an important indicator of potentially mineralised structures elsewhere.

Jan 1, 2007

By Hughson B

The need to prevent the sterilisation of coal stems directly from the fact that it is a non-renewable resource. In N.S.W. a vast amount of coal resource is located under major public utilities such as freeways, railways, stored waters, pipelines carrying gas, water and sewage, and transmission lines. Total extraction has occurred under freeways, transmission lines and pipelines with little or no damage. Where damage has resulted, the cost of restoration was only a small fraction of the value of the coal recovered. However, coal at present is being sterilised and perhaps lost for ever under stored waters and railways. If engineering solutions are available for mining under these improvements economically and with maximum safety, then coal should be extracted and utilised to the benefit of the State.

Jan 1, 1986

By I Gray

Other than being reasonably certain of the average vertical stress being lithostatic, there can be little certainty about stress in the ground. The stresses and strains in rock are a function of gravitational effects, external load, thermal changes, diagenesis and their mechanical properties including elastic, creep and post failure behaviours. It is highly desirable to measure stress where mining is going to take place, even if the virgin stress condition has already been changed by mining. The concept of some far field stress value that is more or less constant is usually invalid and can be dangerous to use in mine design. Measuring stress is not simple. The basic processes are broken into two categories, one where the rock will not fail around the borehole in which the stress is being measured and one where the rock has failed or will fail. Because of the complexity and cost in obtaining a single, precise stress measurement it is highly desirable to have some system to be able to obtain an idea of the uniformity, or otherwise of the stress situation between precise measurements. Table 1 shows the methods for measuring stress. The first five methods work on the basis of some fairly direct measurement of mechanical rock behaviour while the last three are attempts to get some idea of stress out of core long after it is removed from the host rock. While these latter methods appear to tick all the boxes for applicability there is a great deal of uncertainty in the results that they deliver. This paper reviews the methods for measuring stress and presents two new methods. These are a three dimensional overcore system to provide precise stress measurements in rocks that will not fail around the borehole and a core ovality system. The latter can be used to provide information on the stress difference orthogonal to the core. It is particularly useful because it can be used every metre of core length.

Nov 29, 2022

Process variables in flotation circuits are outlined with a view to producing mathematical models of circuits. The nature of the kinetics of flotation are discussed and the effect of process variables on the kinetics considered. An approach for a possible model is briefly outlined.

Jan 1, 1971

By Giuli M, Barnaba P, Sacerdote R, Tammaro F

Following a theoretical consideration of the effect of flooding, fluidisation and softening on blast furnace blowing limits, results are presented which show the effect of these parameters on operation. Industrial trials on Oscar Sinigaglia No. 4 BF are reported and results compared with those obtained theoretically and in the laboratory. It is shown that in these trials the furnace operated at levels of fluidisation very much (80-90%) below those theoretically calculated whereas in some cases (high proportion of sinter) actual hot metal output was near the calculated flooding limit. However, it was observed that as the sinter percentage decreases also actual productivity becomes lower than the one caused by flooding. This gap, which increases as other ferrous components (essentially acidic) replace the basic sinter was explained by the softening of the burden under bosh conditions. Softening indices measured on the individual materials yield support to this explanation. Coke rates data show that for approximately every one percent increase in the basic sinter in place of blended sized ore, a coke rate decrease of 1.1 kg/thm results. For acidic pellets this value is 0.6 kg/thm. Results of breakdown and reduction characteristics are also given and their indices compared with actual pt oduction. Measures to improve operations are proposed.

Jan 1, 1975

By Mallett CW, Rynn JMW, Hammond RH

Geological studies and satellite imagery of the Bowen Basin in Central Queensland, Northeastern Australia, have shown that the significant structural controls are a series of major North East/South West (NE/SW) trending structures, which can be traced as lineaments on Advanced Very High Resolution Radiometer (NOAA-AVHRR) imagery as well as on both Landsat Multi-Spectral Scanner (MSS) and Thematic Mapper (TM) imagery. These linea- ments can be traced offshore and into the Coral Sea by the distribution of offshore reefs and the bathymetery of the Queensland Shelf and the Queensland and Marion Plateaus. The seismic activity in Eastern Queensland seems to be divided into two distinct provinces separated by a seismically quiet area. This apparent seismically quiet area is bounded by two of the large lineaments seen on the satellite imagery. These features could be related to the deep crustal structure of Eastern Queensland and to the opening of the Coral Sea.

Jan 1, 1987

As an Inspector of Mines in Queensland, my main responsibilities include the enforcement of the Mining Act 1968 - 1986, the Mines Regulation Act 1964 - 1983 and the Metalliferous Mining regulations 1985 to promote the safe and responsible exploitation of the States' mineral wealth. An important adjunct to this task is the offering of an advisory service to the mining industry. However, in the pursuit of my duties to this regard, I have sadly observed in some cases, numerous wrong doings and negative activities by miners which have led to their ultimate demise, not to mention that of others. Despite what I consider corrective advice, I have witnessed, again in some cases, disregard and blind pursuit for the wrong end. This then is a novel approach to get the message home in the form of a light hearted cartoon presentation relating the saga of an average Aussie battler entering the mining game unprepared, making the wrong decisions due to his own ignorance and the cleverness of others, leading finally to his and possibly others' downfall. It is not intended to insult any particular profession or group of individuals and only endeavours to impart to readers and listeners, the message of being prepared and alert when entering the gold mining industry. Even though the presentation focuses on the woes of a rookie alluvial gold miner, a similar analogy could be drawn with his hard rock counterpart since the basic issues that I have attempted to address are common. By no means is there a saga complete because there are many more traps a miner can inadvertently fall into and only time has prevented me from referencing them.

Jan 1, 1989

By Mules GJ

Geotechnical investigations have played a key role in influencing decisions for development of the Porgera Gold Project in the highlands of Papua New Guinea. Porgera is located 130 km west-northwest of Mt. Hagen in steep mountainous terrain with high rainfall. Much of the site is underlain by weak mudstone of the Chim Formation and creeping colluvial soils. Landsliding is common on the steeper slopes and in the valley floors. Structures have had to be sited to avoid areas susceptible to these movements. Early stage feasibility investigations included studies of tailings dam and waste rock dump sites, processing plant sites and hydroelectriic schemes. Further studies, leading into the design stage included the Enga Highway upgrading, water supply and power supply schemes. As construction for the project proceeds geotechnical input remains at a high level, with emphasis now on maintaining viable stable sites and refining data on which designs were based.

Jan 1, 1990

Acid rock drainage (ARD) derived from sulphide oxidation and the associated metal leaching is the most significant environmental issue facing the mining industry today. Under given hydrological and biogeochemical conditions, the local geology and mineralogy largely control the formation of ARD. The involvement of a geologist is therefore essential in minesite ARD assessment and prevention. The relevant tasks that a mine geologist may undertake at three major phases of a mining project are briefly described. Additional knowledge that a mine geologist should acquire in order to achieve proficiency in ARD assessment is also suggested.

Jan 1, 1993

By Caigen Wang, Wending Ma, Xiexin Mi

The urgent need for the control of surface subsidence caused by longwall coal mining in densely populated areas of China has led to a feasibility study on the effectiveness of longwall goaf cemented backfill. The study is focussed on exploring the potential of longwall goaf cemented backfill practice for surface subsidence control. Specific backfill geometry was designed in view of the characteristics of the longwall coal mining system. Laboratory physical simulated tests were carried out with different backfill material properties and pack size. The tests achieved a marked reduction in surface subsidence by the use of goaf cemented backfill. The system has been shown to be effective in laboratory tests, the challenge now is to overcome the engineering problems to put it into practice.

Jan 1, 1998