Search Documents

By King RP, Kientzler P

In recent years, ultrasonic comminution technology has been developed at the Utah Comminution Center. An ultrasonic grinding device was assembled and investigated. An ultrasonic transducer system has been significantly improved by using a special type of piezoelectric ceramic and preloading to 4.1 x le kPa to obtain maximum strength. The improved system provides constant and rapid vibratory promotion of fatigue fracture resulting in more effective breakage. The design principles for an ultrasonic mill are developed in this paper. Size reduction was successfully achieved in the ultrasonic nip-roll device for a variety of materials. Ultrasonic comminution has repeatedly demonstrated the capability of producing fine particles from a variety of materials. A comparison between ultrasonic grinding and dry ball milling of limestone showed that the ultrasonic device produced much narrower size distributions than the ball mill. This trend is especially obvious in the coarse size range where few particles remain, and in the fine size range where overgrinding is prevented. This behavior might have some interesting applications in areas other than mineral processing like powder metallurgy or material science where narrow and controlled product sizes are required for the successful elaboration of high-technology ceramics and glasses. Ultrasonic comminution has a significant advantage in the accurate control of the product size.

Jan 1, 1993

During the last two decades, restrictions on access to land for mineral exploration and development in Australia have intensified. State and Federal legislation relating to Aboriginal land rights, national parks, marine parks, wilderness areas and other conservation areas, the surface rights of farmers in New South Wales and Western Australia, national, State and world heritage, urban developments and acquisition of land by governments for other purposes have all placed limits on mineral exploration and mine development activity. More than 20% of Australia's land area is now either unavailable for mineral exploration or available only under severe constraints. Access to this land is denied at a significant economic cost to the Australian community. There have been few attempts to quantify this cost. More importantly these restrictions have developed on an ad hoc basis promoted by single interest government departments often with little regard for rational land use planning. The mining industry has embraced the community's conservation ethic and accepted that conservation areas should be set aside and that within those areas mineral activity should be restricted. In some cases the restrictions on exploration near areas of outstanding scientific, historical, archeological or scenic importance may amount to an effective prohibition. The industry has vigorously opposed the exclusion of mineral activity in conservation areas on purely emotive grounds, unsupported by scientific evidence and in disregard of land use potential, consideration of multiple use potential or consultation with existing or potential land users likely to be effected.

Jan 1, 1987

By Chappell BW

A zone of northwest trending dykes extends for over 600 km in the hinterland from Cairns to Mackay. In sate regions the zone is up to 120 km wide. Figure 1 shows their approximate extent, compiled from published regional maps and from specific studies in more limited areas : Palm Islands, Cardwell Ranges, Jourama Falls, Townsville area and Burdekin Delta. The context of the dyke swarm is the Tasman Orogenic Zone, the region of Eastern Australia conprised of Palaeozoic metamorphic, sedimentary, volcanic and plutonic rocks which has experienced a complex history and evolution. In the Whitsunday region, the Tam-an Zone also involves Cretaceous volcanism and plutonism. Geological relationships indicated a wide span of ages for the intrusions in the dyke, swarm zone. They intrude a range of volcanic and sedimentary rocks, and in some areas plutonic rocks. Older dykes, apparently part of the same regional swarm are intruded by sate of the granites.

Jan 1, 1987

By A Tomsett, J Rutter

Ore control systems at Ridgeway have been designed to deliver gold and copper metal production through focussing on the ore characteristics that impact on mine and mill performance and ultimately metal delivery. This is achieved using data collection and management systems which allow data to be collected digitally with æat captureÆ validation routines. This data forms the basis of forecasting systems which aim to accurately assess local in situ and drawn ore characteristics. Physical attributes of ore such as draw characteristics, brow conditions and visual grade estimation are rountinely recorded. Ore tracking and accounting systems monitor gold and copper grade, copper mineralogy, host lithology and ore sizing. These have material impacts on concentrator throughput and metal recovery. Routine reconcilation and check sampling allow calibration of these systems.

Jan 1, 2002

Author Biography William Poole was born in Sydney, NSW in August 1868. He was educated at Sydney Grammar School. William spent two and a half years as a cadet in the Railway Construction Branch of the NSW Department of Public Works doing office and field work. He then undertook a civil engineering course at Sydney University. Following this he was employed for six years as assistant and resident engineer at the Water Conservation Branch, NSW and was in responsible charge of various field operations, surveys, river gaugings and works of constructions including a large timber weir and also a concrete weir on the Macquarie River, NSW. He then undertook a mining and metallurgical course at Sydney University and became a graduate (BE) with honours in civil engineering, mining engineering and metallurgy. He then spent four and a half years with BHP Co, one and a half years at Broken Hill in the mining and concentration works and three years at the smelting works in Port Pirie, SA, in the latter case he was metallurgist and night superintendent and during that time had responsibility and control at night of the blast furnaces and, during the last 15 months, of the whole of these large works. The author left the Port Pirie, SA works to assume the position of Director of the State School of Mines at Charters Towers and had responsible control of the establishment and also lectured in mining, surveying and structure. William Poole was honoured to hold membership in the following organisations: Assoc M Inst C E, L S of NSW, M Aus Inst M M, Assoc Inst M & M (London).

Jan 1, 2006

In presenting the paper, Mr. Davey quoted subsequent work which yielded k, at miscibility gap composition, of about 50.We can confirm the authors' findings for k j 300 for nearly pure tin to k 2 about 50 (average 47) from our own experience and from repeat experiments on materials described by the authors, at 1150°C.During laboratory-scale trials we also found confirmation of the authors' view that it is more difficult to reach equilibrium from the high-iron (in slag) side than from the low-iron (high-tin) side. Working from the high-iron side tends to yield results that point to a high k, leading to optimistic values of iron/tin ratio in final slags. In practice the smelting of a tin concentrate, unless it is exceptionally low in tin and high in iron, must yield initially a tin-rich slag and therefore equilibrium can only be reached from the "tinny" side.

Jan 1, 1967

The Junction Reefs gold bearing deposit is situated on the Lyndhurst Mining Field in mid-west New South Wales. It is located within a triangle of three country towns namely, Blayney, Cowra and Canowindra, all three townships are approximately 25 km from the current operational mining leases. The district is well developed, having been settled for more than a cen- tury. However, being close to the Cities of Orange and Bathurst it is real- lised, instantly, that mining leases have been pegged, in this area, almost boundary to boundary. The lease patterns are, with few exceptions, those which had been estab- lished more than seventy-five years ago. These types of lease patterns may not assist the proper exploitation of a large district where there have been many discoveries of gold, copper and other metals.

Jan 1, 1988

George Fisher Mine, near Mount Isa in northwest Queensland, has been producing Pb-Zn-Ag ore since the late 1980s. It consists of two separate underground deposits, George Fisher South and George Fisher North. These two deposits are drilled and modelled separately but are crushed and hoisted as a single stream. The Pb-Zn concentrator in Mount Isa processes ore from George Fisher Mine and Black Star Open Cut, with production also from the Isa Lead Mine until January 2006. This paper outlines the steps involved in setting up a robust reconciliation system for George Fisher Mine, in conjunction with requirements of the Pb-Zn concentrator, Black Star Open Cut Mine and the Mount Isa Lead Mine. Good quality input data and commitment to training have contributed to establishing a robust and effective reconciliation system. Reconciliation data has highlighted several other continuous improvement opportunities.

Jan 1, 2006

By D M. Weedon

This paper introduces a novel roll crusher design, which incorporates non-cylindrical crushing rolls. The use of non-cylindrical rolls enables the crusher to achieve a greater reduction ratio than is possible with conventional roll crushers. Referred to as the NCRC (non-cylindrical roll crusher), the new crusher incorporates two rolls comprised of an alternating arrangement of plane and convex or concave surfaces. The two rolls are complementary and arranged so that when they rotate the convex and concave surfaces of each roll are substantially opposed. With the rolls rotating in opposite directions at the same speed, this arrangement produces a gap between the rolls that remains approximately constant. Discontinuities on the roll surfaces provide improved angles of nip, which increase the probability of larger particles being drawn into the crusher. Initial tests on a scale prototype of the NCRC have indicated that reduction ratios exceeding 10:1 are achievable.

Jan 1, 2000

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are steel-based, thin-walled tubular ground reinforcement widely used in underground mines in Western Australia. Following installation these stabilisers are subject to corrosion which may reduce the load carrying capacity and lead to unexpected ground falls. Although corrosion has been recognised as a common occurrence, particularly under aggressive mine water and mineral conditions present in underground mines, the knowledge of the effects of corrosion on the mechanical behaviour of FRS is limited. The Department of Minerals and Energy of Western Australia has conducted a laboratory based program of studies to investigate the effect of corrosion on the mechanical properties of FRS. The studies have focused on the effect of corrosion on tensile strength of FRS and frictional resistance along the interface between FRS and the drillhole wall. The results indicate that under certain conditions corrosion damage can significantly reduce the effectiveness of FRS.

Jan 1, 1996

By Favreau RF

Over the last 20 years the blasting industry has progressed from the stage of being artform to a science as it is today. The use of computers to simulate blasting results has allowed blasting engineers to accurately pre- dict blast results and to optimise their blasting. This paper describes the computer blast simulator called BLASPA and its various applications in blasting. BLASPA allows the blasting engineer to predict blast results given known details of explosive properties, their distribution, rock type and properties, hole size, burden, spacing, collar and subdrill. The simulator runs mathematical situations and outputs numerical estimates of fragmentation and muckpile results. The paper discusses results which show that the mathematical outputs correlate very closely with actual results seen in the field, thus confirming the validity of the simulator. BLASPA can be used to help improve blast design by predicting stress levels in the rock mass and consequent rock breakage.

Jan 1, 1986

Naturally occurring organic plastics have been in use for over 2,000 years. Plastics based on chemically modified organic polymers date back only about 100 years, and those based on synthetic polymers about 50 years. The development of ,these two latter groups up to the present day is outlined, and the basic techniques currently available for polymer-building and modi-fication (blending, copolymerisation, quantitative and qualitative struc-tural control, and'si de-group reactions)-are reviewed.

Jan 1, 1962

By Z B. Rakisheva

By explosion rock mass behaviour is conditioned by preset complex of rocks natural characteristics. Very important role of blockness, which is percent (share) content at examining massif of natural separatenesses of different dimensions and configurations, separated each from other by the cracks of geological and technogene origin. Besides natural properties of massif the power, detonational characteristics of applied explosives, parameters of explosives charges disposition at massif and technology of explosion influence vastly at lumpiness (granulometric structure) of exploded rocks. The mathematical model of rock mass destruction by explosion had been elaborated and substantiated. It ties mutually the initial data (rocks properties, parameters of the charges disposition) and final results of explosion (granulometric structure of exploded rocks). The program of this complicated problem solving had been compiled. Analysing the received results of the problem solving, one can reveal contribution of each group of influence factors for lumpiness of exploded rocks. This fact creates preconditions for elimination or diminution of negative role of some controlled initial data.

Jan 1, 2003

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

By Hutton A. C

Quantitative X-ray diffraction (XRD) analyses using the Rietveld method, a standardless technique for full XRD pattern fitting, showed the mineralogy of the eastern Queensland Tertiary lacustrine oil shale deposits is dominated by detrital cla

Jan 1, 1994

By Parsons AE, Lewis IE

Selenium is a minor constituent of the raw materials processed by the Cockle Creek smelter of Sulphide Corporation Pty. Limited. Certain proposed raw materials contain higher levels of selenium, and these will create a problem with regard to the composition of liquid effluent discharged from the smelter. A method has been developed for removing selenium from the smelter circuit by the sulphation of the fume collected in the Acid Plant electrostatic-precipitators. It is planned that by treating 10-20% of the total dust arisings there will be a substantial reduction in the levels of selenium reporting in effluents when treating selenium-bearing raw materials. The selenium is recovered in elemental form.

Jan 1, 1978

Esso-BHP have installed a Production Supervisory Control System that is presently controlling the offshore oil and gas facilities on the Barracouta and Marlin platforms from an onshore master station. This control is achieved with a computerized master station onshore which uses a UHF radio system for telemetry and control. The system is designed to control, monitor, and gather data from a large number of oil and gas production platforms and has flexability to handle future variations in operating conditions. Thn -etom ..ill kn nvt,,ndnd to thn I-lalihn+ rJ,+f, rr , Into +hie -- -A +n the lei...,fieh .,lo+fnrmc A.,;- 1071

Jan 1, 1970

An analysis of pumping figures suggests that there are two distinct styles of water inflow patterns in Zambia's mines. Carbonate hosted orebodies (Kabwe and Nampundwe) display a characteristic seasonal variation in water inflow with peak pumping showing a short time lag with respect to the rainfall pattern. Aquifer characteristics are controlled by secondary, weathering enhanced, near surface phenomena. Non-carbonate hosted orebodies such as those of the Copperbelt (Konkola and Nkana) occur in successions of highly variable lithology and consequently there are stacked aquifers of variable character. Inflow of water does not display seasonal variation. The major factors affecting the amount of inflow are the structural setting, the geometry of the orebody and the local lithostratigraphy. Thus the Konkola orebodies which occur in a saddle shaped open ended basin result in what is probably the wettest mine in the world, pumping some 376,000 cubic metres of water a day.

Jan 1, 1988

By J Khosa, J Manuel

Iron ore sintering is very complex with many interdependent variables. For the same ores, the sinter quality and sintering performance may vary significantly with the scale at which the sintering tests are conducted. Therefore it is important to understand the effect of test scale on sintering performance and sinter quality while interpreting the test results. In this paper, different scales of iron ore sintering research at CSIRO are described and compared. This is followed by the results of two sinter blends tested at different scales. The results are compared and correlated to demonstrate the benefits of iron ore sintering research at the laboratory (4 g), small (5 - 8 kg) and pilot (55 - 140 kg) scales.

Jan 1, 2007

By Schneider CL

The calculation of the liberation spectrum in the product from continuous milling operations is a problem of considerable importance, and it is difficult to solve because the population balance equation must be integrated in two-dimensional space. Complete solutions require a very detailed knowledge of the complex interactions between the fracture patterns and the mineralogical ore texture when brittle particles are subject to impact fracture. Most of the liberation models that have been developed to date apply only to batch comminution processes and under these conditions the liberation problem can be studied in isolation. When the comminution is continuous and forms a unit operation in a flowsheet that includes classification and separation operations, the situation is very different, and then the liberation of the minerals must be described when single particles of known mineralogical composition are fractured. Important industrial examples are conventional milling circuits closed by hydrocyclone and regrind mills in flotation plants. This paper presents an efficient computational algorithm for the calculation of the liberation spectrum produced by continuous milling operations. The algorithm relies heavily on the detailed internal structure of the Andrews-Mika diagram. The modifications that are required to make this diagram apply to practical ore minerals, and the internal structure of this diagram can be established using single-particle fracture on mono-size, mono-grade material but suitable liberation models are essential to interpret the data in terms of the cross transfer coefficients required for the population balance procedure. Models proposed by Leroux (1992) and King (1990) are compared to experimental data.

Jan 1, 1993