Search Documents

By Armstrong M

Two methods of Monte-Carlo simulations, one suggested by Matheron (1972) and the other by Rudenno (1983), have been tested for simulating coal deposits. To do this 2160 values of ash percentages were simulated using 60 known data points in a two dimensional grid, 20 m x 40 m. 1L is found that while both methods conserve the mean of the known distribution in the results of the simulations, only the first method reproduces the spatial covariance (i.e. the variogram), of the experimental data. The results show that for simulation of regionalized variables only the first method tested yields the desired results.

Jan 1, 1985

The design of the grinding section is discussed and details are given of the equipment installed for the autogenous grinding of ores from the C.S.A. mine at Cobar.The first section of the concentrator commenced treating ore in June, 1965 and operating experience and maintenance requirements since that time are outlined.

Jan 1, 1969

By Thomas L. J

A series of tests on rock stress measurement devices used with the overcoring method indicated that improvements could be made in their construction. A prototype inclusion cell was developed with strain gauge rosettes bonded to a 0.05 mm thickness stainless steel sheet which was formed into a cylinder around two end pieces. The finished diameter was slightly larger than previous cells so that the thinner plate and the reduced annulus of Araldite cement in the installation borehole gave a better response in the laboratory than the other cells tested, especially in simulated bedded rock. It was less affected by inhomogeneity and temperature changes. Its high sensitivity should make it suitable for both absolute stress measurement and field monitoring. A table of comparative readings is given for the new cell and for four other devices used in simulated in-situ rock conditions.

Jan 1, 1992

By G L. Simmons, K M. LeVier, R Kappes

The low potential hydrophobic state of pyrite in amyl xanthate (PAX) flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at NewmontÆs Lone Tree Plant in Nevada. Initially, the N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments, and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Experimental results show the importance of the pyrite surface state and the rather interesting features of the activation process.

Jan 1, 2005

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By Wang Xia, Zhou Aiming, Shi Shengyi

Zhangmatun Iron Mine is situated in the suburbs of Jinan city, Shandong, China. Because of surface environmental constraints, no suitable site can be selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a doubleshaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two stopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining. Utilisation of cemented tailings backfill solves not only the problem of disposal of mill waste, but also the resource problem of providing backfill materials to the mine. The strategy also maximises ore recovery for the mine.

Jan 1, 1998

Saxonvale mine is a multi bench open pit coal mine developed to its Stage I capacity of 1.75 Mt/y of run of mine coal. Detailed engineering studies for the mine commenced in April 1980, approval to proceed with the development was received in July 1980 and first coal shipments were made in April 1982. The engineering and project management of the mine development was carried out by BHP Engineering. This paper outlines the design and site administration for the development and describes both the organisation structure and the control and administration procedures used by BHP Engineering to ensure that the project was Successful.

Jan 1, 1983

By I Arburthnot, N Lawler, C Loan

The function of a thickener is to optimise and accelerate the process of gravity sedimentation. The desired end product (be that maximised concentrated solids or clarified liquid) determines how the thickener is designed and operated.Significant internal research, together with extensive on-site piloting, by Outotec has resulted in the determination that the application of the appropriate amount and type of shear to hindered settling aggregates can result in a substantial change to the sedimentation process. A new patented technology, called shear enhanced thickening (SET), has been developed. SET results in considerable design implications for full-scale thickeners, including a substantial reduction in required footprint and/or significant increases in underflow density.The development of SET, combined with laboratory and pilot scale verification, will be discussed along with the introduction of this technology to a number of full-scale thickeners. The associated implications and benefits for industrial thickeners are outlined.CITATION:Loan, C, Lawler, N and Arburthnot, I, 2012. Industrial scale results from shear enhanced thickening technology, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 341-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Greenhalgh L. P H

The opportunities offered by an increasingly volatile world invite the international consultant or engineering services contractor to broaden attitudes, diversify interests, expand capabilities, retain and develop specialist skills and base judgements upon sound principles and solid experience. The wide-ranging scope of this review reflects such a change but the topics of discussion are not intended to be exhaustive or to detract from many other current developments.The subject of environmental protection, effluent control and pollution prevention is a primary consideration in the application of many mineral processing technologies but is not covered here. There is an array of developments relating to noxious gas emissions and toxic wastes and the paramount importance of this matter justifies comprehensive conferences dedicated solely to the application of suitable measures. This review concentrates therefore on the main stream processing techniques for the primary recovery of values.

Jan 1, 1993

By Gordon N

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By M A. Vinokurova, V M. Mullov

Due to treatment of refractory carbonaceous low-grade gold ores a new technology providing improved precious metal recovery is required. For this reason, a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon in leach (CIL)-process for intensive cyanidation tailings and the recleaned concentrate was developed. The proposed technology allows to decrease preg-robbing activities of concentrates treated by subsequent cyanidation. Total gold recovery by the proposed technology from the ore with a head grade of 0.8 g/t was 83.9 per cent. The gold loading onto the activated carbon from CIL process was 6.500 g/t.

Jan 1, 2007

By Ibrahim AR

The experimental phosphate mine of abu Tartur has been recently placed into production. Some problems'have been encountered in maintai- ning grade control due to the differences between early block estimates and actual produ- ction grade. An area of 100 km2 is evaluated by using four methods of evaluation , namely polygonal, inverse distance , inverse distance squared and geostatistical methods. The results of calculations are compared statistically with the control values of grade and thickness. The comparison showed that the. kriging technique gave better estimations for the relative ore reserved, while for grades or thickness any of these techniques except the polygonal can be Used.

Jan 1, 1986

By R Espinosa-G=mez

Industrias Pe±oles, S A de C V (Pe±oles) in Mexico, is a major silver producer. The Pe±oles mining division has eight operations and the flotation process in seven of them to concentrate the metal and mineral values. Common metal and mineral values are: metallic gold and silver; gold-silver alloy (electrum); silver sulfide minerals (acanthite, pyrargyrite, freibergite, proustite); lead sulfide (galena); zinc sulfide (sphalerite); and copper sulfides (chalcopyrite and bornite). This paper aims to share Pe±olesÆs mineralogical and metallurgical information on the seven operations where the flotation process is used. Some basic conclusions are drawn from this analysis. Some of the information presented includes: types of orebodies, concentration processes, concentrator throughputs, head grades, concentrate grades and recoveries. Importantly, grind size and liberation values for the main mineral species are presented along with the relationships between sphalerite liberation and its recovery, and galena liberation and its recovery. Also included are three mineralogical case studies: maximisation of silver recovery at the Fresnillo mine producing a silver-zinc concentrate; options to improve gold recovery at the Tizapa mine; and sphalerite iron content for the different orebodies.

Jan 1, 2005

The interaction of man with the environment has a double character. From one side, mankind can not exist without co- nsuming the natural resources and, from the other side, we actively alter and exert influence upon nature. Analysis reveals that the ecological problem is, to a great extent, a geological one. The paper deals with the application of grouting techniques to construct impermeable barriers for the protection of ground water and soils from depletion and industrial wastes pollution. A number of case histories in the field of mine construction is given to illustrate the solution of geotechnical problems in concert with environ- mental protection measures.

Jan 1, 1988

By Derham DW, Newcombe LA

The operations of the Mount Morgan gold tailings retreatment plant were significantly improved in 1984 by the desliming of the CIP plant feed, which reduced cyanide consumption and increased percent gold dissolution. Subsequently, the development of slimes treatment, incorporating gold leaching from slimes solids by copper cyanide complexes in the process water, and gold adsorption on to carbon in an environment lacking free cyanide was successfully implemented. Mount Morgan was initially mined for gold commencing in 1882 on the auriferous ironstone cap to the sulphide ore body. During the history of mining and processing at Mount Morgan the operations have developed through numerous phases of gold and copper production, operating almost continuously through until the final closure in late 1990. The final phase of processing was the retreatment of tailings, predominantly flotation tailings accumulated since the 1930s, for the recovery of gold and minor silver. Tailings retreatment commenced in 1982 with the commissioning of a 10 000 tonnes per day CIP plant to treat some 40 million tonnes of tailings at an average grade of 1.08 g/t Au. The initial operations were hampered by high cyanide consumption and poor gold dissolution on the mixed siliceous/pyritic tailings. The successful development and implementation of the desliming of the CIP plant feed in 1984 (as described by Parsons and Hampshire, 1986) reduced cyanide consumption by 40 per cent, and raised gold extraction by 13 per cent points by virtue of significantly higher dissolved oxygen levels. The finer portion of the reclaimed tailings were deslimed by eighty 100 mm diameter AKW cyclones, with the desliming cyclone overflow thickened in a Warman 30 in diameter thickener for water recovery and slimes disposal. Operation of the desliming plant involved the discarding of a slime fraction representing about 15 per cent of the reclaimed feed. Although gold-bearing, the high content of cyanicides and oxygen consumers within the slime negated any conventional treatment of this stream with free cyanide for gold recovery. The natural lixiviant behaviour of the soluble copper cyanide complexes for gold, which was extremely evident at Mount Morgan, directed efforts in this area. Enhancement of gold leaching with a deficiency or near absence of detectable free cyanide, but with significant levels of copper cyanide complex from recycled process water were examined. Adsorption of this solubilised gold onto carbon in a similarly difficult environment required close examination.

Jan 1, 1993

Metsim is proving to be a powerful tool when designing a heap leach operation. The most useful outputs arc determining the fluctuations in pregnant solution recovery rate, make-up water rate, gold recovery rate. and pond levels. Detailed data are needed for input: a pad loading schedule, a mining rate schedule for each ore type, column leach test data for each ore type, column tests on water dynamics (ie hourly flow-out versus-in during saturation and drain-down), monthly rainfall and evaporation data, and proposed pond dimensions. These data allow 'what if' studies on application rates, leach rates, loading rates and other variables of interest. Examples will he given of modelling both a rectangular pad and a valley fill operation.

Jan 1, 1994

In his letter of resignation as General Superintendent of the Broken Hill Associated Smelters (BHAS) prior to taking up aconsulting position at imperial Smelting, G.K. Williams wrote that he considered his major contributions at BHAS were:the development of large scale sintering machines;the double tuyere-row blast furnace; continuous lead refining.Despite his well deserved reputation as a scientist, based on his advancement of the metallurgical chemistry underlying lead refining processes, Williams reveals that he considered commercial implementation as the ultimate measure of technological success. Furthermore, he clearly did not differentiate between the scientific and the empirical as a means of achieving that end.

Jan 1, 1985

By M Maulen, K van Olden, T Elkington

A large open pit is planned at the site of an existing underground mine. Strategic planning work has been undertaken to investigate the project value associated with an expansion of underground operations in conjunction with the proposed pit. Previous analysis determined that any depletion of the available pit resource that changes the optimum pushback sequence has a significant negative impact on overall project value. Therefore, to investigate the viability of an underground expansion requires a system to identify the stope resource that would add value to a combined operation if mined ahead of the pit. The key solution to this problem was to generate a resource model variable that defines the blocks, which have greater discounted value if mined by stoping rather than by the open pit. A key assumption was that the open pit is the main driver of overall project value. From the identified potential underground resource, series of mineable stope shells were generated at a range of cut-offs. This stope reserve data formed the input to a mixed integer program based software tool that was developed and used to optimise the underground mining plan, at conceptual level, for various project configurations. A dynamic programming tool was then applied to evaluate the optimum value of a combined open pit and underground operation. The overall objective of this project was to determine the strategic plan that yields the optimum value for a combined undergroundûopen pit operation. The results provided a clear focus and direction for more detailed design and planning.

Jan 1, 2009

Electromagnetic methods used in geo- physical prospecting for conductive ore bodies have proved successful in Canada,Sweden and other countries. In Australia however the depth of weathering generally exceeds 30 metres. This introduces a problem of highly conductive overburden and renders equipment useful elsewhere virtually ineffective. A discussion of several EM prospecting techniques is presented and a new system under development at James Cook University using V.L.F. transmissions capable of indicating changes in impedance (not only highly conducting media) is outlined.

Jan 1, 1974

This data is intended to provide a quantative cost comparison of one 40 800 kg. pull down rotary blast hole drill versus two smalter drills in the 18 100 kg. pull down class. While this cost analysis is affected by blast design, this paper is not intended to be a treatise on blasting theory and therefore places more emphasis on costs than on blast design. All costs, prices and production rates in this paper are estimates and should be used for comparison purposes only. The drills are sized in order to maintain a production rate sufficient to stay ahead of a dragline that is excavating in an average overburden (sandstone and shale). The large drill will use 270mm bit and penetrate at a rate of 0.012 m/s (scheduled basis). The small drill will use 170mm bit and penetrate at a rate of 0.010 m/s (scheduled basis).

Jan 1, 1986