Search Documents

The total cost of horizontal development can be minimised by optimising the cost of each of the component operations (eg drilling, blasting, etc). Component costs should not be minimised. To optimise blasting results (ie the mean advance per round, muckpile characteristics and overbreak), operators need to optimise the blast design and drilling and blasting procedures. The costs of pulling extremely long (say >6 m) rounds, producing unnecessarily fine fragmentation, and minimising overbreak are excessively high. Operators should continually consider how they can shorten the cycle period by saving time at the face. To enable it to be matched to the pertinent rock properties, the blast design needs to be based on as much relevant experience as possible. To develop the most valid correlation between blasting results and blast design, the latter must be implemented carefully and accurately, but without sacrificing speed excessively. The total cost can often be reduced by using: 1. computer-controlled jumbos (to reduce the period and cost of drilling and to increase drilling accuracy); 2. larger diameter (51 mm to 64 mm) and longer (4.5 m to 6 m) blastholes; 3. at least three large diameter ( ¦89 mm) relief holes that are 0.2 m to 0.3 m longer than the blastholes; 4. explosive products that are selected on the basis of proven reliability and overall cost efficiency rather than price; and5. stemming (to increase the amount of effective work done by each kilogram of explosive and, hence, to reduce the powder factor and possibly the number of blastholes and the costs of drilling and initiation). Non-perimeter blastholes should be charged with ANFO or a bulk emulsion of established performance. Upper perimeter blastholes should be charged with a bulk explosive with a much lower effective density. But where geology varies considerably, greatest control over overbreak could possibly be achieved with the versatile pre-assembled charge shown in Figure 1. This paper presents numerous potential ways in which the total cost of development can be minimised. It concentrates on recommending blast design features and the safe, rapid, cost-effective implementation of designs.

Jan 1, 1998

By G S. Beros

In 2019 the Chinese Ministry of Ecology and Environment issued guidelines promoting the implementation of ultra-low emissions in the iron and steelmaking industry. These guidelines aim to drive improvements in air quality through the reduction of particulate matter (PM), sulfur dioxide (SO2) and nitrogen oxide (NOx). Secondly, it also represents an initial means to commence decarbonisation of the industry. The ultra-low emissions guidelines propose that well over 80 per cent of China’s production capacity will achieve these targets by 2025. In response, many sintering operations have implemented numerous improvements to the process that result in significant efficiency gains. Of note is the adoption of deep bed sintering where, with some modifications to equipment, the sintering bed depth is increased resulting in sizable reductions of SO2 and NOx emissions. This paper will also provide an overview of the requirements to introduce deep-bed sintering into an operation and highlight test work completed which quantifies the resultant reduction in emissions.

Nov 8, 2021

By I M. Platten, Y Xie, R-M F. Bell, S C. Dominy, L E. Howard, R C. A Minnitt

For any resource evaluation program, the collection and processing of representative samples for assaying is critical. Sampling, sample preparation and assay protocols must be designed to suit the style of orebody in question. The a priori need is for the characterisation of mineralisation type(s) and domain definition. The proportion and size of gold particles has a direct impact on the effectiveness of sampling protocols employed. Mineralogical studies focusing on gold particle deportment, size and distribution are required. Key issues are the presence of gold particle clustering and proportion of coarse versus fine gold. High-resolution X-ray computed tomography (HRXCT) is a radiographic technique that produces high-resolution 3D computerised models of in situ objects based on density distribution. The ævirtualÆ specimens are made up of voxels, the 3D equivalent of pixels each assigned a grey value based on X-ray absorption. This paper presents the results of recent research on the imaging of in situ particles in coarse gold-bearing ore samples from the Nalunaq mine, southern Greenland. The samples used were previously well-characterised through mineralogical and metallurgical testing, and serve to test the HRXCT methodology. Gold particle size and distribution in the context of the sampling liberation diameter was investigated.CITATION:Dominy, S C, Platten, I M, Howard, L E, Xie, Y, Bell, R-M F and Minnitt, R C A, 2012. Determination of the sampling liberation diameter in a high-grade coarse gold ore by high-resolution x-ray computed tomography, in Proceedings Sampling 2012 , pp 161-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named 'RAMOCE' has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski's rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010

To the industrial geologist, as wen as to the general or historic geologist, the possession of a reliable key to the true order or sequence of the stratigraphy or position of the various upper rocky envelopes of the earth's crust, is, equally, a desideratum of the utmost importance. Of similar value to the two groups of students is the possession of facts which throw light upon the relationships which subsist between the puccessive rock formation of different countries, especially between countries lying close to each other, or within the same great geographical division.But there is necessarily a fundamental distinction which marks the respective limits of the field of observations of the industrial geologist, and the purely historic interest of the general geologist. The former has a more definite though less extensive scope. The scope of the latter is wide and indeterminate. In short, the observations of the industrial geologist are, 'from a commercial or economic point of view, of a more practical character, and are, therefore, intentionally restricted to the study of all geological questions which throw light upon the rocks which yield products of economic value and only include the study of the character and history of other rocks, in so far, as they afford aid to the more perfect comprehension of the best manner in which materials of economic value are likely to be sought, and the best means whereby these products may be secured for the material advantage of the community. The motive of the general geologist-in most cases-is a love of the study of some particular branch or province of the geological field, and the fascination of opening a new volume in nature's library, and the hope of extending the realm of knowledge, however slight, are often sufficient, as a motive, to enlist the energy and life's devotion of the true brethren of the hammer, irrespective of considerations regarding the commercial utility of the pursuit.

By W Valery, A Jankovic

A growing demand within the minerals industry for sustainable development and the introduction of carbon taxes have resulted in a significant focus on improving the energy efficiency of comminution circuits. However, in this drive for improved energy efficiency the role of classification has been overlooked. Inefficient classification and large recirculating loads reduce circuit capacity, result in over-grinding and higher specific energy consumption.It is well understood that classification increases mill capacity; therefore, closed ball mill-cyclone circuits have become an industry standard. However, due to limitations in cyclone classification efficiency, the optimum recirculating load is limited to about 250 per cent. A simple relationship quantifying the effect of classification efficiency and recirculating load on grinding circuit capacity is presented in this paper. The possibility of improving the capacity of ball mill circuits by improving classification efficiency is discussed, considering the current practical limitations of classification equipment. Simulation tools were used to evaluate circuits with cyclones and with high frequency screens to identify opportunities to improve energy efficiency. The investigation also identified potential benefits to flotation recovery due to a reduction in over-grinding.CITATION:Jankovic, A and Valery, W, 2012. The impact of classification on the energy efficiency of grinding circuits - The hidden opportunity, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 65-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D W. Nisbet

Today Hudson Bay Mining and SmeltingÆs 777 Project is the largest mining construction project under way in Canada. The project comprises six components: construction of the new 777 zinc-copper mine; construction of the new Chisel North zinc mine that will truck ore out from 600 metres below surface; expansion of the Flin Flon ore concentrator; expansion of the zinc plant to increase throughput by 15 per cent; a spill gas project that will reduce fugitive gas emissions by some 90 per cent; and infrastructure improvements including construction of a new electrical substation. Total investment in The 777 Project is over $US 260 million. Seven years ago, the Flin Flon, Manitoba-based company was fighting for its very existence. How does a company go from down-for-the-count to robust contender in just seven years? Contributing reasons are many, but all have their root in a process HBMS calls æTransformationÆ. It is transformation that has taken HBMS, a very traditional company, through a very non-traditional turnaround (Figure 1).

Jan 1, 2000

By K J. McDonald

All commercially available zircon sands contain radioactivity sourcing from the decay of trace amounts of contained uranium (U) and thorium (Th). The fine particle size zircons of the Horsham area in the Murray Basin region of Victoria, Australia, contain significantly more (about twice) Th+U than those commercial zircon sands. The marketability of these fine-grained zircon sands is likely to rely on the removal of these radioactive impurities. CSIRO Minerals have been working for some time to develop processes for the removal of the radioactive impurities from zircon. It is generally agreed that it is quite impossible to leach U and Th from zircon, however, the Heat and Leach (HL) process, described in detail in Aral and McDonald (1999), reduces the radionuclide levels significantly. The identified (HL) process aims to leach uranium and thorium selectively from a decomposed zircon. The novelty of the process is that a large part of the leached product can be reconstituted to a low radiation zircon by a subsequent heat treatment. The HL process uses a flux mixture of sodium carbonate and calcium borate to decompose the zircon at relatively low temperatures (900 to 1150¦C) and a weak acid (0.5M HNO3; 80¦C/0.5 h; pulp density ten per cent) to leach the radionuclides selectively. The process leaves the major components (ZrO2 and SiO2) behind with little loss. The HL process for example lowers the U+Th content of a Murray Basin zircon from 1000 ppm to 400 ppm U+Th. Among the radionuclides more U progeny is removed than the Th series radionuclides. This is very significant as the radioactivity of U series is 2.5 times more that from the Th series. Therefore the reduction in the radioactivity level of zircon is more than the reduction in Th+U indicated by XRF analysis. A schematic flow sheet of the HL process is shown in Figure 1. Although the HL process successfully lowers the radionuclide levels in zircon sands, the final product contains significant amounts of sodium (up to 14 per cent Na2O) and small amounts of CaO. By comparison, the sodium content of the commercial zircon sands is in general 2O. Zircon is used mainly as an opacifier in tile glazing where the addition of ten to 15 per cent zircon to a translucent base glaze gives the sanitary white colour to the tile surface. Opacification is the result of the refractoriness of zircon particles at the glaze firing temperatures that is generally around 1050¦C.

Jan 1, 2001

By C Sellens, L D. Fabbro, S Vink

The Fitzroy River Aqua-Eco Health Project is a collaborative research project between the Central Queensland University, the University of Queensland and BMA. It is designed to assess the aquatic ecology and health of the streams within the Fitzroy catchment located adjacent to mine sites. The universities are conducting an independent sampling program expected to yield the most comprehensive monitoring to date. The project design incorporates in situ testing of water quality variables including temperature, dissolved oxygen, conductivity, oxidation reduction potential, pH and turbidity. Water and sediment chemistry incorporate testing for sulfate, suspended solids, nutrients and metals. This sampling is complemented by quantifying changes in the abundance and diversity of a wide range of biota, including microbial, macro invertebrates and fish.This paper will detail the program and highlight some of the particular difficulties in conducting this type of research in ephemeral stream systems. Case study examples will be used to illustrate insights being gained from the program. CITATION:Fabbro, L D, Vink, S and Sellens, C, 2013. The Fitzroy Aqua-Eco Health Project, in Proceedings Water in Mining 2013, pp 117-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

This report will differ slightly from the traditional scientific and technical discussions given at this type of conference. It will focus on the personal experiences and choices that I undertook when deciding on my graduate position and location after completing university studies. Throughout the duration of my course I had experience in both fly-in, fly-out operations in the Pilbara and residential operations in the West Australian Goldfields. These experiences, though limited, allowed me to explore the two different methods and their pros and cons, and consequently to make my choice for graduate employment. Throughout the duration of my degree I believed it was important to gain a basic understanding of the two methods, focusing on lifestyle and personal interactions. The decision that a residential site suited my personality and lifestyle then allowed me to refine my job applications to a more specific list of mine sites and companies, resulting in a residential position with BHP Billiton at their Iron Ore operations in the Pilbara, Western Australia.

Jan 1, 2005

By R M. Stephenson

Large diameter raise boring is a common raise excavation method in the Australian mining industry. Geotechnical investigations were conducted on several large diameter raise bore projects at Gwalia Mine to assess the potential for instability and potential back-reaming problems. A thorough geotechnical analysis and subsequent back-analysis was conducted on a vent raise excavated at 5.5 m diameter and 810 m length.The geotechnical investigation for the vent raise included collection of data from an acoustic televiewer survey that was conducted on the pilot hole. The survey results provided structural data and an insight into the effects of stress on the pilot hole. Structural analysis was conducted using a combination of information obtained from the acoustic televiewer survey and geotechnical logs of the diamond drill core drilled close to the site.Further information was collected from drillers’ plods from pilot hole drilling and back-reaming to conduct a back-analysis of the completed shaft, and this was compared with the structural analysis.The key finding from this review was that the acoustic televiewer survey of the pilot hole accurately identified locations with blocky conditions. This is an important supplement to the information available from the main geotechnical investigation hole, as this was offset from the shaft location over most of its path.CITATION:Stephenson, R M and Sandy, M P, 2014. Structural analysis of acoustic televiewer logs for large diameter raise bored shafts, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 89–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A. G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids, and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue-gases, the circulating fluid bed technique with internal oil combustion at 220°F for the calcining step and a five-stage fluidized bed cooler for heat-recovery from calcines, the process gives an outstanding heat-efficiency. In a first industrial plant for 560 sh. tons/day of alumina heat consumption figures of less than 1·400 B.T.U./lb Al203 g were achieved.

Jan 1, 1972

This paper has been prepared to challenge the thinking of new leaders entering the mining industry in two areas. First, what is the worldÆs perception of mining and what does this mean to those entering the industry? Second, what is the future of learning in the mining industry and how can the industry attract and retain the best people?Then in closing, how can mining companies turn these challenges into opportunities and specifically how is BHP Billiton meeting these challenges.

Jan 1, 2004

By B N. Morrison

In all metallurgical plants metallurgists require analyses of the various intermediate products, eg flotation feeds, flotation concentrates, tailings, mattes, slags, etc to monitor the efficiency of the plant processes and for plant control purposes. Traditionally these samples have gone to off-site laboratories and there can be some considerable delay before analytical data are received. On-line monitors have to be used for plant control purposes and these are difficult to maintain and can give poor quality data. Recent technological advances in automation in analytical laboratories now allow a far quicker turn-around time for analytical data so they can be of more use to the metallurgist. Automation, which involves the use of robots and fewer people in laboratories, has the added benefit of providing higher quality data as the possibility of human error and bias is minimised. Differences between conventional manual laboratories and automated laboratories are described. Automated analytical laboratories are now becoming the laboratories of choice for mining companies which require large numbers of samples to be analysed on a 24/7 basis on similar sample types using the same sample preparation methods and analytical procedures. Automated laboratories have now been installed in platinum, iron ore, copper and aluminium producing mining companies. A further advantage to metallurgical plants is now the possibility of siting automated analytical laboratories in-plant and designing the plant around the laboratory. Concentrator streams, slags, etc can be sampled by automated samplers, the samples transferred by automation to the in-plant laboratories and all sample preparation and analyses carried out by automated processes. These laboratories require a minimum of staff. Such automated in-plant laboratories have been installed on a platinum mine flotation plant, a platinum mine smelter and steel plants. One is in process of being installed on an iron-ore mine with the sampling being carried out by an automated sampling tower. The procedures followed in planning an automated analytical laboratory for a metallurgical plant are described in detail in the paper. The platinum plant smelter automated system which includes rapid transport of samples by air-tube to the laboratory for the analysis of the samples by XRFS is also described in the paper. It is concluded that automated analytical laboratories can be retro-fitted to most metallurgical plants but they are best suited to greenfield sites.

Jan 1, 2008

By M Paakkunainen

Sampling is often the most critical part in process analysis. When the mean of a continuous lot, such as a process stream within a given time interval, is estimated by calculating the mean of several samples, the uncertainty of the estimated mean depends usually on the sampling strategy. Three different strategies can be used: systematic, stratified or random sample selection. The standard deviation of the lot mean is different for these methods so that systematic sampling usually gives the smallest and random sampling the largest standard deviation. Pierre Gy developed a method where the sampling errors of one-dimensional lots for these three strategies can be estimated from a variogram, which is calculated from a variographic experiment, ie from a set of one-dimensional time series measurements with fixed sampling interval. While variogram is an excellent tool for characterising and displaying the variability of autocorrelated processes as function of time, the sampling error estimation from it is quite laborious, however. In this work an alternative method for estimating the sampling errors was developed. The process is divided into strata of equal sizes, varying the length of strata similarly to variographic analysis. For stratified sampling the standard deviation estimates are obtained by analysis of variance and for systematic sampling by fitting a linear regression line to each stratum and calculating the residual variances. By pooling the individual variance estimates the variance estimates that are corrected for autocorrelation are obtained. The new method was tested with simulated and real data sets having periodic, random and/or drift fluctuations. For stationary processes the results agreed well with the results of the GyÆs variographic method. The method can probably be generalised to estimate the sampling variance of higher-dimensional lots.

Jan 1, 2005

By McElrae AJ, McTaggart SM

The recent rapid escalation in computer use by mining companies, particularly in technical applications, can in part be traced to a growth in the availability of specialist packaged software. Such software, often developed by independent software companies provides economies of scale, end user orien- tation and breadth of scope imposed by market forces. This paper reviews the emergence of these companies and current software econo- mics before extrapolating present trends to consider the effect of future fourth gen- eration languages upon productivity.

Jan 1, 1983

By J Robinson, L D’Uva

"The Gold Fields group and Gekko Systems have successfully worked together on multiple projects, including at the St Ives, Agnew and Granny Smith operations in Western Australia, and the Damang operations in Ghana, with gravity recovery design, technology installation and optimisation the key driver on each occasion.In 2014, Gold Fields Australia identified an opportunity to challenge the historical thinking at Granny Smith and reassessed the benefit of upfront gravity gold recovery. The historical approach had been to employ gravity on the tailings stream of the carbon-in-pulp (CIP) circuit, recovering sulfide minerals into a concentrate from spiral concentrators for further liberation of gold via a regrind circuit.Gekko was engaged to assess the implementation of a gravity circuit within the grinding area, and to perform a comprehensive gravity recoverable gold test program. Test data was fed into the AMIRA P420 BCC Gravity Model to confirm the gravity recovery potential of the ore, and for process design basis generation. Height, space and capital limitations proved to be a design challenge. However, collaborative learnings throughout the project ensured the design and operation of a reliable and economic gravity gold circuit. Ultimately, the Granny Smith gravity circuit was a success, satisfying all the project objectives and yielding consistent, measurable benefits. On average, the gravity circuit recovers 33 per cent of total gold, resulting in an increase to overall gold recovery by 0.7 per cent.This paper highlights the key project drivers for Gold Fields, and the development of the Granny Smith free gold gravity circuit. It details application of test work and modelling, and the challenges and learnings encountered during the design, installation and commissioning stages. This paper seeks to demonstrate that continuous improvement in a long standing operation can be beneficial to overall circuit flexibility and increased ounce production.Citation:D'Uva, L, Robinson, J and Bell, T, 2016. Defying Gravity - Brownfield Continuous Improvement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 135–144 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J Rose, D O’Toole, D Grant

Orepasses are a critical element in the transport of ore from the stope drawpoint to the surface ore stockpile, making them an integral part of an underground mine’s ore-handling system. Well-designed and operated orepasses improve productivity and lower operating costs over a long period of time.The Olympic Dam mine, as part of a 6 Mt/a expansion project in 1997, constructed a large network of orepasses feeding a rail haulage system to facilitate the movement of approximately 8 Mt/a to the Clark crusher and hoisting shaft. The orepass network comprises 14 orepasses and currently includes 59 individual tip points. The orepass network has been in operation for over 15 years and in excess of 110 Mt of ore has been moved through the system.Olympic Dam’s management of mine infrastructure includes a program of assessing the condition of the Clark system orepasses. A comprehensive program was initiated in 2011 and consisted of systemically performing volumetric surveys to determine the integrity of the various sections of the orepasses. The current geometrical state of the orepasses provides essential information for comparison of geotechnical and operational parameters and a baseline for understanding the key causes of orepass deterioration to assist in the planning of both usage and potential replacement options.The collection of geotechnical and operating data allowed the review of the current condition, potential longevity and associated risks with the various orepass sections. Initial studies have also reviewed options for rehabilitation and/or replacement.CITATION:Rose, J, Grant, D and O’Toole, D, 2016. Orepass monitoring and management at Olympic Dam Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 609–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By AJ LYNCH

Broken Hill metallurgists have been responsible for some of the most important developments in mineral processing technology. These occurred mainly in two periods, 1902 - 15 and 1955 - 70. Mineral flotation was developed as an industrial process during the first period and this happened in two stages, the recovery of zinc minerals from the tailings dump accumulated during the gravity concentration of the oxidised ores and the selective recovery of galena and marmatite during flotation of the primary ores. During the second period fast accurate analytical procedures were developed to provide rapid assessment of process performance, and new means of controlling the process were devised which improved throughputs, grades and recoveries. These technological successes were due to the skills of the metallurgists and the commitment of the companies. They brought large financial returns. They were achieved under difficult circumstance. There are important lessons to be learnt from these successes.

Jan 1, 1992

Soon after the Rosebery concentrator commenced operations in 1936, an investigation was begun in an attempt to discover a substitute for cyanide in lead flotation. Cyanide is an excellent depressant for zinc and iron, but it also powerfully depresses the copper, silver and gold bearing minerals present in Rosebery ore, thus allowing them to pass through to the zinc concentrate or final residue where they are of little or no value.The investigation was not entirely successful, but it did indicate that sodium bisulphite or sodium sulphite could be used as a depressant for zinc without depressing the copper, silver and gold bearing minerals. The sulphites were, however, much inferior to cyanide as apyrite depressant.At about this time, I. W. Wark, using the captive bubble technique, had shown that, at the concentrations normally used, sodium aerofloat is not a promoter for pyrite or galena in alkaline solutions (see his book "Principles of Flotation", p. 188). Some preliminary tests on the production of a copper concentrate from Rosebery ore were therefore carried out using sodium sulphite as depressant and sodium aerofloat as promoter.The results of this work were promising but, since Rosebery ore usually carries only about 0·5% copper, there did not seem to be much incentive to carry the work further. With the outbreak of war, however, Australia became desperately short of copper and the relatively small amount in the ore. became of sufficient importance to...

Jan 1, 1952