Search Documents

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Hennessy F. L

IntroductionEvolution of the Present SmelterRoastingFiringHearth SlopeDust HandlingFurnace DetailsSmeltingFurnaceFeed DeliveryPulverised Coal FiringWaste Heat BoilersDust HandlingAir PreheaterReverberatory Slag DisposalConvertingVesselsAir SupplyMatte TappingConverter Slag HandlingPurchased Ore PlantINTRODUCTIONSmelting in blast furnaces commenced at Mount Morgan in 1906, when copper, which interfered with gold recovery by chlorination, became an asset. After various changes in blast furnace practice, reverberatory smelting com...

Jan 1, 1952

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

The State of New South Wales is highly favoured in having vast deposits of coal adjacent to and within easy reach of the coastal Ports. Not only is the quality of the fuel generally superior to any found in the other States, but it is greater in extent than in any other part of the Continent. For interesting and reliable details of the history of the discovery of coal, the geology of the coal bearing strata, analysis of the various coals and other valuable data, the readers are referred to the book recently issued by the New South Wales Government, entitled The Mineral Resources of New South Wales, by Edward F. Pittman, A.R.S.M., etc., by the direction of the Hon. T. L. Fegan, Minister for Mines. The mining community is indebted to the Minister for having had published the most valuable condensed record of the mineral resources of the State extant.For the purposes of this paper we will only give such a general description of the coal fields as will make it intelligible in connection with the subject of the coal mining in the State of New South Wales.

Jan 1, 1904

By S J. Schafrik, E S. Gilliland, E C. Jong, J Waynert, C W. Weiss

Two commercially available through-the-Earth (TTE) communications systems were evaluated at an active underground longwall mine in West Virginia. One system utilises magnetic field (H-field) antennae while the other system utilises electric field (E-field) antennae to achieve communication. A large portion of this mine is overlain by an inactive gas-oil field composed of densely spaced wells. This feature provided a unique opportunity to determine the impact of cased wells on both TTE technologies. The following communication modes were investigated: surface to underground, underground to surface, underground to underground and real-time two-way communications. Standard deployments of the TTE systems using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations under certain circumstances. As a result, the design and deployment that will optimise TTE transmissions are unique to each system and to the specific area of the mine. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivity. The performance of these two TTE systems suggested that one may be preferable over the other depending on the conditions present during deployment.CITATION:Jong, E C, Schafrik, S J, Gilliland, E S, Weiss, C W and Waynert, J, 2015. Pairing magnetic and e-field through-the-Earth communication systems based on mine site conditions, in Proceedings Third International Future Mining Conference, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

The Morning Star diorite dyke has been subjected to two periods of mineralization. The earlier, genetically related to the dyke magma, gave rise to a weak chalcopyrite-pyrrhotite-pentlandite-gold mineralization in a narrow zone, up to 25 cm. wide, which parallelsthe nearby western (hanging) wall of the dyke. Subsequently a set of conjugate shears formed in the dyke as a result of tectonic movements. Gold-quartz veins formed in these shears giving rise to the classical "ladder veins" of the Morning Star mine. On either side of the veins ("floors") the diorite has been bleached for up to 3 ft. This involved introduction of much CO. and some K"O, and S with abstraction of SiO. and FeO, giving rise to carbonates, sericite, zoisite and pyrite. The veins consist of quartz with minor amounts of albite and carbonate, together with pyrite, arsenopyrite, pyrrhotite, chalcopyrite, sphalerite, tetrahedrite, galena, bournonite, boulangerite and gold. Spectrographic analyses of gold show that the suite of trace elements is consistent throughout the mine.INTRODUCTIONThe gold-quartz veins of the Morning Star Gold Mine, at Wood's Point, Victoria, are a classic example of the "ladder vein" type of deposit. The structure of this series of repeating quartz veins or "floors", some barren and some productive, occurring in a set of conjugate shears which transect a "dyke bulge" of diorite (Fig. 1), has been described on numerous occasions as mining has progressed and figures in the textbooks (Whitelaw, 1905; 1916; Junner, 1920; Lindgren, 1933; McKinstry, 1935; 1942; 1949; Kenny, 1949; Hills, 1952; Clappison, 1953) ; but there has been no study of the mineralization apart from that in Junner's (1920) general study of the Walhalla-Wood's Point Goldfield, made at a time when mining had not developed below the 400 ft. level,. and the mine was dormant.

Jan 1, 1958

By G J. Harbort, Z Pokra

It has been observed in several Jameson cell installations where the source for flotation feed is deslime screens, that the recovery of coal particles greater than 0.5 m is not as great as that of finer material. Consequently, a research project was undertaken at a CHPP in the Bowen Basin, Queensland, to assess the possibility of increasing the recovery of coarser particles (+0.5 mm) within the downcomer of the Jameson Cell. The effect of decreasing turbulence and agitation in a commercial-scale downcomer was investigated to assess the effect on the recovery of both coarse and fine coal particles. This paper details the findings of the testwork, summarising the results relating to differences in the operating parameters within the downcomer.

Jan 1, 2005

By C Mroczek, B Mitchell

Perilya Broken Hill, from its inception, has budgeted for more than 2.0 million tonnes per year from the Southern Operations. This tonnage was planned to come from in excess of 100 stopes per year in a remnant mining environment with numerous mined voids and consequent mining challenges. To mine an average of two stopes per week requires patience, flexibility and detailed knowledge to best manage the potential risks and hazards. The evolution of the Perilya Broken Hill Mine Planning Process has necessitated the establishment of a process to identify and manage these risks during the planning stage in a reliable but efficient manner. This process is to ensure that vital steps for each stope are not missed, and that each personÆs work can be tracked by other members of the team. This paper outlines the planning process from resource to stope closure.

Jan 1, 2005

I want to explore whether it is valid or even useful to talk about sustainable corporations. After 20 years of focus on sustainable development, the concept of a sustainable corporation is not particularly helpful and it may in fact be profoundly misleading. Why? û because it obscures the need for corporations to be recognised as part of a sustainable society, rather than achieving some kind of corporate nirvana divorced from the social, political and environmental reality. It is more helpful to ask whether corporations are ready to recognise that they are one player among many within society û with the demands this would place on them in terms of transparency, accountability and social responsibility. The achievement of sustainable development has become the new corporate orthodoxy of many large corporations. It has become a clichT to argue that corporations must become æsustainableÆ. The achievement of æsustainabilityÆ is encouraged, as the ultimate step in some form of corporate evolution. We are failing to recognise that sustainability a process û not an end in itself. An enormous array of instruments is being developed to measure when sustainability is or is not being achieved. For example, corporate reporting has burgeoned into an art form, which describes æsustainabilityÆ in a variety of ways. There is no external standard applied to such reporting. These descriptions are quite partial and often place the best possible gloss on the companyÆs activities. I have become increasingly uneasy about this rhetoric and this paper has allowed me the luxury of sorting out my unease. I will discuss, largely in the Australian context, the current debate and literature and describe the way some global mining corporations are dealing with these questions, and finally, offer some suggestions which might be helpful at the operational level.

Jan 1, 2002

By P Gomez, R Baumgartner, G Escobar

"The Cerro Corona mine consists of a Cu-Au porphyry deposit located in the Andes of northern Peru. The deposit comprises a typical Cu-Au multiphase porphyry mineralisation that has been overprinted by an epithermal event. This has generated a complex pattern of argillic alteration facies, which was accompanied by a locally structural-controlled Au-Cu mineralisation with the presence of gold and limited Cu sulfides and sulfosalts. These features, along with the porphyry-style mineralisation, produced a multifaceted occurrence of gold.Since the beginning of operations at Cerro Corona in 2008 there has been a continuous improvement of the geological and mineralogical knowledge. All mineralogical studies have mainly focused on host rock types and, to a lesser extent, alteration minerals, but little work has been done on the mineralisation itself. As a consequence, limited mineralogical information was available for use in the process optimisation initiatives.In the last two years, a series of mineralogical characterisation studies were undertaken with two main goals. First, to gain an understanding of the mineralisation genesis and second, to obtain a detailed characterisation of copper and gold minerals to support ongoing process optimisation. The first goal was achieved by conventional optical microscopy while the second required electronic microscopy and other microanalyses due to the necessity of quantifying several minerals of interest for the processing.The results were used to refine pre-existing geometallurgical domains, explain copper and gold losses in the flotation process and to some extent, improve copper and gold recoveries. The mineralogical characterisation is an ongoing work. Mineralogy provides the basis for any optimisation exercise since it looks in detail at the material to be treated and therefore, should be part of all geometallurgical programs.CITATION:Baumgartner, R, Gomez, P and Escobar, G, 2016. Comprehensive Mineralogical Characterisation at the Cerro Corona Cu-Au Porphyry Mine – the Fundamental Key for Geometallurgical Applications, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 221–230 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By G Burton, S Fityus, J Li, S Vaughan, D Payne

Daunia and Caval Ridge coal mines, owned and operated by BHP, have been co-disposing rejects and dewatered tailings within spoil dumps from the beginning of their operations in 2013 and 2014, with the purpose of minimising environmental impact and geotechnical risk. Following the recent large failures of tailings dams around the world, BHP Coal, through its Coal Tailings Program, plans to transition other coal mines to deliver “dry” tailings and produce mixed plant rejects (MPR) for inpit co-disposal. This will materially reduce future tailings dam risk exposure. Previous laboratory shear strength testing was conducted on rejects with a maximum particles size of 20 mm, and some concerns were raised that this might not represent the mechanical properties of the actual full particle size distribution (PSD) rejects. BHP was also aware that using different technologies to dewater the tailings, such as belt press filters (BPF) and solid bowl centrifuge (SBC), could produce thickened tailings which could significantly modify the physical behaviours of the MPRs, particularly the bonding between particles. Therefore, laboratory testing on both coarse rejects and mixtures of the coarse rejects and dewatered tailings (MPRs), with full PSDs, was carried out. Testing was performed using the large direct shear machine developed by the Australian Coal Association Research Program (ACARP) project C20019 in 2017, as well as a 300 mm diameter triaxial apparatus at the University of Newcastle (UoN). This paper presents details of the laboratory testing program and results for the rejects from the first studied mine of the BHP Coal Tailings Program. It compares the shear strengths measured at full scale with those tested on modified (scalped or crushed) specimens in the past; and discusses the tailings dewatering technique selection from geotechnical aspects based on the testing results, and finally presents some dump and tip head stability analysis results using the testing results.

Jul 1, 2021

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022

This paper cites selected, prominent examples of current, major projects in Southern Africa in both the mining and civil fields. Differences and similarities in the life cycle of mining and civil projects are discussed. A closer relationship between the mining and civil fraternities is beginning to develop and should be encouraged because of the resultant exchange of experience and technology which benefits both disciplines. An attempt is made to assess future potential for new, major projects and trends in the implementation thereof.

Jan 1, 1999

By M Erskine, R Mills

This paper approaches tailings dam risk management from the perspective of how other high hazard industries approach the management of their catastrophic event risks, with the aim to provide recommendations from these learnings for the industry to adopt.

Jul 1, 2021

By N Bianco, D Drinkwater

The professional skills shortage is intensifying, and commentators are predicting a shortfall in supply of qualified professionals for the mining industry, ranging from thousands to tens-of-thousands by 2020 (Tuckwell, 2011; Scoble, 2011; Laurence and Hebblewhite, 2011). Human resources are already stretched, and university graduates arriving in the workplace are often moved rapidly into management positions where there is limited scope to develop their engineering proficiency. This process may well be developing excellent young managers, but our industry is producing fewer excellent young engineers (Munro and Tilyard, 2009). Many believe that it is engineering excellence that is likely to be the key to our industryÆs success in the decade to come. An innovative in-house graduate development program has been created by specialists at the JK Centre in partnership with two mining companies. This program, known as MetSkill«, has been running throughout 2012. Groups of graduates have had to identify a process plant optimisation opportunity and embark on a structured program of data collection and analysis, facilitated by a æteaching teamÆ of researchers and consultants from the Julius Kruttschnitt Mineral Research Centre (JKMRC) and JKTech. This group project culminates in a report-back session to senior company officials. Along the way, a series of short workshops and other activities provide opportunities to work on specialist skills, and support is also offered by senior technical specialists from the companies involved.This paper outlines key features of the MetSkill« program, along with a report-card on progress in 2012 and plans for further program development in 2013.CITATION:Drinkwater, D and Bianco, N, 2012. Developing minerals industry leaders by encouraging metallurgical excellence, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 287-290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Welcome to this 13th Congress of The Council of Mining and Metallurgical Institutions. It is twenty one years since The Australasian Institute of Mining and Metallurgy last hosted this congress and it is a privilege and a pleasure for The AusIMM to have that responsibility once more. The theme of this congress "The Twenty-First Century - Mining for Mankind" stimulates many thoughts. The first thought that it generates in me relates to the reference to the 21st Century. We are still 14 years away from it and already consideration of the beginning of the next millenium is becoming something of a cliche. If we feel like that about it now, how will we feel at the 14th Congress of the CMMI in 1990, or the 15th in 1994 or the 16th in 1998? If we do all the crystal ball gazing about the 21st Century this week, those poor devils in the 1990s will in fact have nothing to talk about. Of course that is not the case. This is a very appropriate time for those of us concerned with mining and metallurgy to contemplate the next century. Fourteen years is about the extent of forward planning necessary in the mining business. I sometimes feel that most people do not take seriously the need for long range planning in our industry. Politicians, investment fund managers, and others under severe short-term pressure to perform in our hyperactive world may nod in apparent appreciation of our long term plans but their actions in the interests of expediency often betray-them.

Jan 1, 1986

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development teamÆs processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement.TSG Consulting advocates a ætotal integrated system approachÆ to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By D Cotnoir, Q Liu, D Richard, M Ourriban

The difficulty in fine particle flotation has been attributed, among other things, to a low bubble-particle collision efficiency. Many technologies have been developed which aim at increasing bubble-particle collision efficiency, either by generating micro bubbles or by enlarging particle sizes. However, commercial applications of these technologies are limited. Over the last five years COREM has been actively testing fine particle froth flotation technologies with the objective of commercialisation. Several fine particle flotation technologies, such as dissolved air flotation, electro-flotation, floc flotation, selective flocculation-flotation and carrier flotation, were tested on both single minerals and ore samples in order to identify the reasons that prevented these technologies from being used on a commercial scale. It was found that the two most noticeable factors that prevented the successful application of these technologies were: Mechanical entrainment of fine gangue minerals. This was a general problem in fine particle flotation, but was aggravated by these technologies that either generated micro bubbles or enlarged the sizes of hydrophobic particles. Oxidation of (sulfide) minerals that resulted in hydrophilic oxidation product coatings. The oxidised fine particles could not be recovered by these fine particle flotation technologies effectively. Solutions to the two problems, ie gangue entrainment and fine particle oxidation, were proposed and tested. It seems that polymeric depressants with both depression and flocculation functions could significantly reduce gangue entrainment, and hydrophilic surfaces of oxidised fine particles could be modified by high intensity conditioning or controlled sulfidisation, thus increasing the recoveries of fine valuable minerals. The improved fine valuable particle flotation and reduced fine gangue entrainment along with fine particle flotation technologies resulted in much improved flotation separation of fine particles.

Jan 1, 2005

By B Murphy, N Strong, J Albrecht

Rio Tinto’s Argyle Diamond Mine has a history of underperformance with delivery of ore from the underground operation to the surface for processing with no real clarity in sources of loss and value. In order to increase underground production performance, the basic concepts of the Theory of Constraints model were applied to the Argyle underground production system. This prompted a revised view on bottlenecks and contributors to value loss and ultimately leading to record breaking mine performance. System loss reporting to demonstrate the best opportunity to drive value, departmental detail to develop tools to identify improvement opportunities and clarity across the team to ensure alignment and clear lines of communication were critical to the project success.

Mar 15, 2021