Search Documents

By P Duplancic and C R Lilley, R Hudson, D Beck

For deep block and panel caving mines, undercut or extraction level instability can have as much impact on overall recovery as underbreak or the premature ingress of waste. If the area of the mine affected by excessive convergence is small, recovery is usually possible. However, there are several examples of entire blocks that were abandoned prematurely due to footprint collapse. Clearly, such global instability has a major impact on recovery and must be avoided – this is one of the essential tasks for the design team.The design problem is complex. The planning engineer must ensure that the footprint has sufficient capacity to withstand the maturing loads in the cave, accounting for the effects of stress path, geological structures and the rock mass conditions. These are often uncertain and only sometimes quantified.The demand on the footprint will also be influenced by decisions and actions taken during production, especially related to draw, which can worsen a developing problem. Perhaps most importantly, the design decisions that favour stability and lead to lower deformation also negatively impact on idealised cave flow. Many engineers aim to minimise the size of extraction level pillars, to improve theoretical future resource recovery but in fact this can reduce recovery if widespread deformation ensues due to the undersized pillars.In 2014, PT Freeport Indonesia undertook detailed numerical analysis to quantify the effects of variability in rock mass conditions and geological structure on overall footprint performance. The analysis accounted for a range of stress paths and maturing cave loading scenarios sourced from a calibrated whole-of-cave deformation-flow model. The intent was to replicate some of the diversity and distribution of pillar deformation outcomes that may be seen in practice at Freeport.The discontinuum finite element analysis was able to replicate damage localisation around persistent structures, a realistic distribution of drive deformation and show how small areas of instability can evolve into major problems if poorly managed. The limits of pillar size and ground support as solutions to a number of different instability problems was also investigated, showing that pillar size alone was not a sufficient remedy for all adverse circumstances.In this paper, we describe the workflow for numerical analysis of footprint deformation. We discuss the compromises and considerations for balancing the sometimes competing needs for efficient extraction levels pillars, ground support and prudent draw strategy.CITATION:Beck, D, Hudson, R, Wilson, A D, Duplancic, P and Lilley, C R, 2016. An investigation of factors affecting the long-term reliability of extraction level pillars in deep block and panel caves, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R L. Chaney, M Mahoney

Mine and ore beneficiation wastes and smelter contaminated soils often cause phytotoxicity and threaten adverse environmental effects if not remediated. Science has clarified both the risks from soil metals and methods to alleviate those risks that can be applied at low cost. Phytoremediation is a family of plant and agronomy based technologies to deal with environmental aspects of sites requiring remediation. If valid risk assessment indicates that metals comprise risk, phytostabilisation may be used to alleviate that risk for most contaminated sites. In particular, Zn-Pb, Cu and Ni mine and smelter sites are readily remediated by making the soil calcareous and fertile, with added organic and metal sorbent amendments that include soil microbes to ‘revitalise’ the soil. In each case, the soil fertility and causes of phytotoxicity should be clarified by agricultural soil extractions, and the combination of amendments required to improve fertility and reverse phytotoxicity identified and found locally. In contrast with phytostabilisation, phytoextraction/phytomining uses rare metal hyperaccumulator plants and agronomic management to maximise annual phytoextraction of soil elements into plant shoots for harvest, ashing and use as a metal ore. Plants that accumulate more than two per cent Ni in shoots, and yield 10–20 t ha-1 dry biomass yield 200–400 kg Ni ha-1, which has value greater than all common agricultural crops. Considering the value of elements, existence of hyperaccumulator plants and demonstrated agronomic management for Ni phytomining, it is clear that mine sites and Ni mineralised subore-grade serpentine soils can be phytomined economically as an agricultural mining technology. A team developed agronomic methods and improved cultivars of Alyssum, which can be profitably grown on temperate zone Ni mineralised or contaminated soils. Plant species for tropical ultramafic soil materials have been identified. Phytoextraction is also strongly needed to remove Cd from rice soils to prevent human disease from soil Cd.CITATION:Chaney, R?L?and?Mahoney, M, 2014. Phytostabilisation and phytomining – principles and successes, in Proceedings Life-of-Mine 2014 , pp 3–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J H. Heo, J H. Park, M J. Lee

In this paper, the challenging points regarding the high temperature physical chemistry of slags to achieve the improved and stable electric arc furnace (EAF) or electric smelting furnace (ESF) technology on the way to green steel will be reviewed, and the recent experimental and modelling research will be discussed. For example, the initial melting phenomena of hot briquetted iron (HBI) and the slag formation behaviour was observed using a high-frequency induction furnace. Main component of gangue oxides in HBI was SiO2, Al2O3, and CaO in conjunction with unreduced iron oxide. To increase the dephosphorisation efficiency, the distribution ratio of phosphorus between metal and slag was calculated using FactSage™ software, version 8.2 (CRCT ThermFact, Inc., Montreal, Canada) and was compared to the measured results. The optimisation of slag chemistry is required not only for maximum dephosphorisation efficiency with good slag foamability but also for minimum slag volume with less refractory corrosion in EAF process. The slag chemistry is also one of key parameters affecting the operation efficiency in ESF in view of FeO reduction behaviour, viscosity, sulfide capacity, etc.

Jun 19, 2024

By J Nantel

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

By Holla L, Tyminski A

Stowing has been successfully used in many countries as a means of controlling surface subsidence, minimi ing incidences of spontaneous combustion, maintaining gate road stability and maximising coal recovery.Australian experience in stowing is limited but in the future increased extraction of thicker and/or multiple seams by longwall operations and resolution of conflict of alternative land u'ses may necessitate the use of stowing in coal mining. At present there is little incentive for mining companies to introduce and operate a stowing system because costs have to be borne by the individual companies and benefits spill over to society and the State. Cost sharing by the industry and State incentives may overcome the problem of cost disincentive.

Jan 1, 1987

By C Smith, J Cilliers, K Hadler

Unstable flotation froths, that burst before they overflow, produce no concentrate. Increasing the froth stability to improve recovery is therefore an obvious control strategy. Froth stability can be measured readily as the fraction of air entering the flotation cell that overflows as froth, rather than bursting on the surface; the ‘air recovery.’ Air rate is one of the most significant variables affecting froth stability. It is interesting that froth stability (air recovery) is maximised at a specific air rate, above or below which it decreases. It is important for metallurgists to realise that this maximum froth stability also produces the maximum mineral recovery, without compromising concentrate grade. Flotation cells must be operated at the air rate that produces the highest air recovery. The peak air recovery (PAR) to maximum mineral recovery relationship was first demonstrated by Hadler and Cilliers in 2009. Since then, the relationship between PAR and flotation performance has been widely explored; varying air rate, froth depth and particle size. Industrially, reducing the flotation bank air rate to achieve PAR yielded better mineral recoveries than other down-the-bank air rate profiles. In this paper, we present an overview of these key developments and findings in flotation optimisation based on PAR. Furthermore, using new industrial data, we show that PAR is not just applicable to rougher-scavenger cells, but also to flotation columns. Finally, we consider the future application of such an optimising control concept. CITATION:Smith, C, Hadler, K and Cilliers, J, 2018. Flotation control using froth stability: past, present and future, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 441–454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By R Marchant, D Willingham

"Predictive maintenance (also known as PHM or equipment ‘health monitoring’) refers to the intelligent monitoring of equipment to avoid future equipment failures. In contrast to conventional preventive maintenance, the maintenance schedule is not determined by a prescribed timeline; instead, it is determined by analytic algorithms, such as machine learning, using data collected from equipment sensors and/or via simulation.Predictive maintenance offers the following benefits for operators and equipment manufacturers:reduction of equipment downtime by identifying issues before failure, thereby enabling convenient scheduling of equipment service and extending equipment lifetimeautomatic determination of the root cause of the failure, enabling appropriate service to be performed without utilising resources to determine a diagnosis avoidance of costs of unnecessary maintenance and unexpected failures improved safety and product quality.Algorithms and data are critical to predictive maintenance success. Sensor data preprocessing is performed using advanced statistical and signal processing techniques. In the case that data isn’t available for the full range of operating modes, operating scenarios can be simulated. Machine learning techniques are then used to estimate equipment health. Once tested, predictive maintenance algorithms may be operationalised in an IT environment such as a server or cloud. Alternatively, algorithms may be implemented in an embedded system directly on the equipment, allowing for faster response times and significantly reducing the amount of data sent over the network.In this paper, we use both historical and simulated data of the plant under various modes of operation including run to failure, and we then leverage machine learning techniques in MATLAB to estimate degradation and remaining useful life. This technique, of combining both simulation models and machine learning, in the areas of predictive maintenance and equipment health monitoring has been adopted by Safran, makers of aircraft jet engines, since 2007. They now have over 160 modules developed (Lacaille and Aurelie, 2015).Citation:Willingham, D and Marchant, R, 2016. Predictive Maintenance Using Simulation and Machine Learning, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Nixon C. A

The exploration of Mount Isa Mines' new copper source will require the development of a five kilometre 4.7 x 5.5 metre blind decline commencing 1000m below the surface and extending to 1600m below the surface. With virgin rock temperatures approaching 60¦C, the ventilation strategy represents a complete departure from any previously used at this mine, in that refrigeration becomes essential. The use of direct water to air cooling techniques has become commonplace in mines throughout the world and their application is being adopted at Mount Isa Mines. A heat load simulation routine has been implemented to allow for the design of refrigeration requirements, as well as to aid in the selection of diesel or electric equipment. This enabled planners to determine the size of a surface based refrigeration plant. Future refrigeration demand for expansion into the ore production stage has also been investigated.

Jan 1, 1988

By J Hartnett, B Tarrant, A Rayner, D O’Toole, P Davies

Since 2009, the Northern Territory and Australian governments have been working under a national partnership arrangement to inform a rehabilitation plan for the former Rum Jungle uranium mine. Part of the rehabilitation strategy is to backfill a flooded former pit (Pit), which extends down to 100m below the current pit lake surface and was historically partially backfilled with uranium tailings. It is proposed to utilise the remaining pit volume below water level to sub-aqueously store Potentially Acid Forming (PAF-I) waste rock which currently occupies large stockpiles across the site. The rehabilitation design and planning process undertaken to develop a strategy commensurate to project objectives and construction constraints involved the establishment of key constraints derived from the analysis of historic data sources and preliminary design efforts. Tabled strategies were balanced against dependent project tasks and project objectives, especially surrounding minimising disturbance of highly contaminated materials within the Pit. Ideas were developed in conjunction with industry input and review of case histories to develop a remediation solution that is constructible within the project timeframe and constraints.

Jul 1, 2021

Greymouth River Dredge û Birchfield Minerals Ltd Blackwater Gold Mine û Macraes Mining Company Ltd Globe Progress Gold Mine û Macraes Mining Company Ltd

Jan 1, 1996

By W T. C Kendall, H D. Ngo

Garden Well is a shear-hosted Archaean orogenic gold deposit located 100 km north of Laverton, Western Australia. The Garden Well processing plant is designed for a nominal 491 t/h milling rate and annual capacity of 4 Mt. The plant has three key innovations:1. a scrubbing circuit, expected to reduce grinding power consumption by up to 20 per cent2. a secondary cycloning/gravity circuit, providing a second opportunity for gravity gold recovery (additionally, the circuit effectively increases the leach residence time of the coarse gold bearing fraction of the leach feed by approximately 60 per cent, without any additional tankage)3. the use of mid-stream oxygenation to enhance gold recovery.The Garden Well deposit is free-milling with overall laboratory gravity/leach gold recoveries exceeding 95 per cent at a P80 grind size of 150 ¦m. Three mineralogical domains have been identified: oxide, transition and fresh, with the fresh domain having subdomains of fresh ultramafic and fresh shale. There is a high component of gravity recoverable gold in all three domains.This paper will discuss these innovations and the design challenges and the risk mitigation strategies that were adopted to ameliorate the prototyping risk. The performance of the plant since commissioning together with lessons for the future will also be presented.CITATION:Smith, R J, Kendall, W T C and Ngo, H D, 2013. Treatment plant innovation at Garden Well, in Proceedings World Gold 2013 , pp 315-324 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G Balog, T Ormerod, D Cox

This paper discusses the methods utilised by the technical team to identify and quantify the SLC risk factors, the modifications to mine design and scheduling, and the changes to the planned risk management practices. The paper also describes the future work currently planned by the OZ Minerals technical team to quantify the various risk factors in terms of space, time and magnitude. This may better inform the future mining practices within not only the Carrapateena province but also the wider Gawler Craton.

Mar 15, 2021

In the course of work being carried out in the Lubricants and Bearings Section of the Council lor Scientific and Industrial Research on the production of copper4ead 'bearings for 'use in aircraft, it has been found necessary to develop special metallographic methods. For proper control of the production of steel-backed copper-lead bearings it is necessary to adhere to rigidly controlled conditions, and it is essential that a method of examination be adopted which will readily detect actual defects or any variations in quality. Some defects can be observed with the naked eye, whilst others are detected by radiographic examination. This latter method is invaluable as a rapid, reliable test in the production of aircraft bearings, but it is necessary to observe the structure of the alloys under the microscope, both to be able to interpret the radiograph correctly and to determine what has occurred to the metal during and after solidification. The use of a sound metallographic technique is'particularly important in developmental work and research connected with these bearings.Polishing TechniqueCopper and lead are practically immiscible in the solid state, but whilst they are miscible only in certain limited proportions in the liquid state; consequently "alloys" of copper and lead consist of a mixture of the constituent metals. The metallographic difficulties are obvious. Copper is a relatively tough metal, although it readily scratches, whilst lead is extremely soft and easily deformed. It wouId be expected if any normal polishing technique were applied that the lead would be readily torn out of the surface being prepared, and, in addition, that the lead would tarnish very easily.Grange(2) has described a method by which these difficulties can be overcome. The method involves an etch-polish procedure using "chrome regia" as an etchant for the copper. The chrome regia was a solution of chromium trioxide and hydrochloric acid in water. This type of etchant has been adopted, but it was found necessary to make certain changes.The method now adopted in this laboratory is as follows: The specimen (which is usually mounted in bakelite) is wet ground in a series of successively finer Hydro-Durexsil emery papers down to 60.0· grit paper.The specimen is then etched in the chrome regis, etchant (the composition of this etchant will pe discussed later) for approximately five seconds.Most efficient etching is obtained by swabbing the surface of the specimen...

Jan 1, 1944

The theme of this paper is the development of-the project feasibility study which includes discussion of the work which is carried out in preparing the project feasibility study, the necessary evaluations and structures that are employed to ensure that not only does the feasibility study itself stand up to scrutiny and is sound, but also that the investment the company is proposing to develop, "the project", is an investment decision which will represent good returns to the company. This theme is particularly relevant when there are competing divisions within the company and only limited cash resources are available to make the correct investment decision. Thus various potential investments may be evaluated against each other to determine which project will be given the go ahead for development. This paper will particularly focus on the various investment analysis techniques that are used and discuss the work that is required in preparing the project feasibility study and specifically the interaction of the project team members and the thought process that must be undertaken to complete the project feasibility study. Finally comments will be made on tax planning issues particularly with respect to taxation of gold production to be introduced in January 1991. Some ideas are presented which may help and possibly improve the financial position of the projects being reviewed. Further, it is suggested that the thought process which goes with the financial engineering aspects of a resource project can be widened to take account of taxation issues and tax planning to ensure the rise of the project feasibility and hence the decision to proceed to development by the project sponsors.

Jan 1, 1990

By T Schrimpf, I Bryan

The life cycle of a mining project begins with initial regional exploration and ends with mine closure and rehabilitation. Between resource definition and the commencement of mine construction is the study phase. In this phase technical concepts and processes are defined, evaluated and assessed with the aim of establishing whether the deposit is economically feasible. The study phase usually involves various steps from a concept/scoping study to prefeasibility and ultimately definitive feasibility study. The complete study phase can take several years. Although the costs for studies are low in comparison to actual construction and operating costs of a mining project, they are significant especially for junior exploration and mining companies advancing projects to the point of being funded.The studies aim to determine selected parameters for the project, eg mining and processing methods, operating strategy, etc and provide a roadmap for project development ahead. Although mining studies are of the utmost importance for the mining project and the project owner, they are usually carried out using a conventional engineering approach: the consultant or design engineer works to a defined scope of work. The resulting design might be based on good engineering, but might often also fail to provide the solution for the project owner that delivers the best shareholder value. An alternative to this more traditional approach to project evaluation is what we have termed a value engineering approach. Value engineering is a creative, organised effort, which in the case of a mining study analyses the requirements of the study for the purpose of achieving the essential outcomes with the highest shareholder value. The outcome of a study is a concept that delivers the highest achievable value of the resource project and shows the way ahead to realise this value. Through a group investigation by experienced, multi-disciplinary teams the value of the resource is improved through the study of alternative options, methods and processes. The scope of the study is not limited to a narrowly defined engineering scope, but to the creation of value.The study commences with the identification of key value drivers and risks, based on the available information (drill data, geotechnical data, metallurgical test work, etc). This enables the quantification of key uncertainties, risks and value adding opportunities. Study efforts concentrate on key value drivers and are not unnecessarily spent on side issues. This approach can significantly reduce the time frame and costs for the study phase.This paper describes in more detail RMDSTEMÆs value engineering approach to mining studies and illustrates it with examples and case studies.CITATION:Schrimpf, T and Bryan, I, 2012. The application of value engineering principles to mining studies, in Proceedings Project Evaluation 2012 , pp 163-170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By H Q. Zhang, M C Chai, W Fu, H Y Chen, L M. Wei, Q J. Yang

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Fozichong deposit – located in the south-western segment of the giant Qinhang metallogenic belt, South China – is a large-sized lead-zinc polymetallic deposit. This deposit contains two main ore districts, termed as the Guyi ore district in the north and the Hesan ore district in the south respectively. We present an integrated data set on sulfide minerals, fluid inclusions and stable isotope (H-O-S-Pb) geochemistry to better understand the features and genesis of the Fozichong deposit.Field and paragenetic relationships indicate three mineralisation stages forming the early (Po+Sp+Gn+Ccp+Py+Di+Ep+Qtz), middle (Sp+Gn+Ccp+Py+Ep+Chl+Qtz) and late (Gn+Sp+Py+Qtz+Cal) sulfide assemblages respectively. Mineral chemistry – particularly S/Fe and Co/Ni ratios in pyrite, Zn/Fe, Zn/Mn and Zn/Cd ratios in sphalerite and Pb/Ag ratios in galena – indicates a magmatic association for the sulfide minerals.Quartz and calcite coexisting with the sulfide minerals of various stages host abundant fluid inclusions. Quartz in the early stage contains two- or three-phase CO2-H2O and liquid-rich aqueous inclusions, which have homogenisation temperatures of 162~365°C and salinities of 2.9~17.8 wt per cent NaClequiv, whereas quartz and calcite from the middle and late stages are dominated by two-phase, liquid-rich aqueous inclusions that have slightly lower homogenisation temperatures (153°C~320°C) and much lower salinities (1.0~6.0 wt per cent NaClequiv). Hydrogen isotopes (dD = -59‰~-41‰), analysed using fluid inclusion waters from quartz and calculated oxygen isotopes (d18OH2O = -5.47‰~4.00‰) for the equilibrated ore fluids, indicate that the ore-forming fluids may have been sourced from magma and mixed with groundwater in the late stages. Sulfide minerals have d34S values of 2.3‰~4.3‰, consistent with a magmatic-derived source for sulfur. Lead isotopes (206Pb/204Pb = 18.592~18.794, 207Pb/204Pb = 15.648~15.864, 208Pb/204Pb = 38.909~39.580) confirm that lead and, by inference, zinc were mainly derived from magmatic rocks, with subordinate contributions from sedimentary rocks.Various lines of evidence support that the formation of the Fozichong deposit has close genetic association with the granite porphyry intruded in the late Yanshanian period (106 Ma), and it can be classified as a magmatic hydrothermal type lead-zinc deposit. We propose that the Hesan and Guyi ore districts may represent the proximal and distal products of a magmatic – hydrothermal system respectively.CITATION:Fu, W, Zhang, H Q, Chai, M C, Yang, Q J, Chen, H Y and Wei, L M, 2015. Genesis of the large-sized Fozichong lead-zinc polymetallic deposit, Guangxi, south China – constraints from the sulfide mineralogy, fluid inclusions and isotope geochemistry , in Proceedings PACRIM 2015 Congress, pp 609–614 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By B Wu, B W. Lei, B J. Duan

When a coalmine fire occurs, it is crucial to judge the developing trends inside the fire area by analysing the changes of gas concentration in order to formulate the proper rescue measures. At present, few researchers have focused on the relationship between the changing trend of gas product and basic characteristics of fire in the coal fire extinguishing process. To study the relationship of basic characteristics of coalmine fire during the extinguishing process, an experimental platform for coal combustion in a confined space was built, and gas production, flame image and coal temperature during the extinguishing process were monitored and analysed by an online continuous gas analysis instrument, camera and thermocouple. Research shows that during the burning phase of the coal sample in the confined space, the flame zone decreases gradually due to insufficient gas supply. The size of the flame zone fluctuates and shares a positive correlation with CO concentration, while sharing a negative correlation with O2 and CO2 concentrations. Then, in the extinguishing phase, the increasing rate of CO2 concentration and the decreasing rate of O2 concentration both decrease gradually, but CO concentration would rise for a period before it eventually decreases. Coal temperature continues to rise in the open flame stage and does not go down until the flame is extinguished.CITATION:Lei, B W, Wu, B and Duan, B J, 2015. Experimental study on extinguishing characteristics of coal fire in confined space, in Proceedings The Australian Mine Ventilation Conference, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June, 1,,896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to -the works, the firewood being of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides).The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall. The areas so far exploited aggregate a total of about 42 sq. 'miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cub. ft. per ton, 60 tons per acre being considered a good average yield. The gross amount of firewood handled during the past 13 years approximates 1,200,000 tons, the greater portion of which has been obtained by ordinary tramming methods. The company's main line of railway, 3-ft. 6-in. gauge, has served as a trunk line for all supplies derived from the Queen River valley, south of the reduction works, while the northern and western areas have been exploited by means of...

Jan 1, 1911

By D P. Blair

The theme of this conference is blasting productivity. This article only considers the technology aspect of this theme, and in particular, the collection and analysis of experimental data. In many cases, field trials are set up to collect data on variables such as fragmentation and vibration with the aim of comparing different explosive products and/or blast designs. An important aspect of such trials is the collection of sufficient data to draw sound conclusions. In this regard, there is no doubt that the scatter in real data is the root cause of all problems of obtaining misleading results due to an insufficient number of trials. This article shows that the typical one-off trial has a high probability of producing misleading information, which could be considered to be worse than having no information at all. Assuming that sufficient data has been collected, this article also highlights the methods that can be used to make the most of that data. These methods include the application of appropriate statistics that are dependent on the nature of the scatter in the data, and the use of some of the more recent filtering and spectral approaches that can be used to reduce the noise in measured blast signals and increase the resolution of their spectral characteristics.

Nov 8, 2011

This paper addresses, in particular, the influence of winding depth on the selection of head ropes for Koepe winders. Because this is just one aspect of winder design that affects the operational safety of the winding system, the paper starts by considering all the issues governing the life and safety of the winding ropes. Regulations from a variety of countries are reviewed and comparisons of the legislated rope factors of safety and their variation with winding depth are made. This is followed by a discussion of the typical observed mode of in-service deterioration of Koepe head ropes. This mode of deterioration is due to fatigue and is influenced by the load range occurring in the ropes. Parameters contributing to load range are discussed and the influence of winding depth is highlighted. Lessons learned from early experience with very deep Koepe winders in South Africa are recalled. Predictions of load range as a function of depth are made, from which general rope life predictions are made for ropes selected by conventional national factor of safety requirements. This is illustrated in graphs comparing rope life as a function of depth. Typically a reducing life with depth is predicted. A rope selection strategy is advocated, which is based on achieving a constant rope life irrespective of the depth of wind. A new factor of safety (or rope design factor) equation is prepared that has the trend of increasing with depth. This proposed equation is compared with other published proposals that promote an increasing rope factor of safety with depth. It is shown that smoother winder drive controls enhance winding rope life and this improvement is quantified. The paper concludes by pointing out the consistency in predicted and observed life of winding ropes selected in accordance with legislated factor of safety approaches. It recommends the adoption of a new rope design factor equation for rope selection, to be used in conjunction with appropriate codes of practice for winding rope condition assessment and for the design, installation, operation, maintenance and testing of Koepe winders. The new rope design factor equation approaches a limiting economic depth of wind at shallower depths than the existing Koepe factor of safety approaches. However these older approaches æbuild-inÆ a reducing rope life with depth. The new rope design factor is therefore a more consistent way to select Koepe ropes and to evaluate economic trade-offs between Koepe and conventional double-drum or Blair winding systems.

Jan 1, 2005