Search Documents

By Thomas L, Archibald N

The use of oxygen in the Mount Percy cyanidation circuit was investigated, with the aim of improving recovery. Preliminary batch and plant testwork justified a plant trial, and it was demonstrated that the use of oxygen reduced gold leachable from plant tailings by 12 per cent, and was economically viable. Oxygen is now in permanent use. Other benefits of oxygen in leaching were not proven. There were no savings on compressed air costs and no measurable reduction in cyanide consumption, although HCN levels in the atmosphere above the tanks declined. The possibility exists that more efficient use of compressed air for tank aeration could have achieved similar recovery gains.

Jan 1, 1992

By M E. Watson

Minimising dilution and ore loss is an important part of ensuring profitability of a gold mining operation. White Foil open pit gold deposit is a low-grade deposit and therefore managing ore quality is a high priority. Ground movement through blasting can displace ore and waste boundaries up to 10 m from their in situ location and therefore requires stringent ore movement monitoring and adjustment. There are currently only two options for monitoring blast movement – utilising visual targets (commonly lengths of polypipe) but this has widely been replaced by electronic blast movement monitors (or BMM). Regardless of the technology used, the basic principle is to compare the pre- and post-blast locations of the targets to determine the movement of the rock mass during blasting, which is then used to determine the final location of ore and waste boundaries.The Blast Movement Technologies (BMT) BMM system has been used at White Foil since June 2014. The system has been effective and reliable during that time; however, the annual cost of using the BMM system is greater than other monitoring alternatives. As such, the open pit geology team conducted a study comparing the BMM system against the conventional polypipe technique. The objective was to quantify the profit and loss that would occur based on the ore block transformations from both methods. Eight blasts were selected where polypipes were installed in additional holes adjacent to the BMM monitoring holes. The resulting movement vectors from the respective methods were used to create post-blast ore blocks by transforming the in situ ore blocks. While polypipe is a cheaper alternative, the BMM system tracks ore and waste boundaries more effectively resulting in better quality control, enhanced ability to minimise dilution and ore loss thus maximising profit. For these eight blasts, it is calculated that the BMM system resulted in A$664 978 extra profit through a reduction of ore loss. The total cost of a yearly BMM package was recovered in the first two blasts of this study. The primary reason for the difference is that polypipe had a poor recovery rate of 32 per cent compared with 92 per cent for BMM at White Foil. Therefore, the data used to transform the ore blocks was less representative, resulting in inaccurate post-blast ore block boundaries when using polypipe.CITATION:Watson, M E, 2017. Blast movement monitors or polypipe? A study into cost-effective blast movement monitoring at White Foil gold mine, Western Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R Hoeppel, D Harimon, A Fisher

This paper examines the importance of examining the relationship between biology and geochemistry when designing a biopile to treat alkaline soils impacted by petroleum hydrocarbons. At a site in Nevada a large, unlined pit was constructed in a loamy sand soil and filled at regular intervals with a mixture of jet fuel, lubricating oils and waste solvents which were set on fire by the local fire department for training purposes. During its period of operation numerous chemicals were also dumped into the pit for disposal purposes, including dichlorobenzene and various chloroethylenes. As a result of these activities a large groundwater contaminant plume was formed. As a part of the site remediation process a decision was made to perform a limited source removal and excavate the top three to four metres of contaminated soil from the burn pit and place it in an engineered biopile. The location of the training pit is in a heavily mineralised basin where the background sulphate level in groundwater exceeds 5000 ppm. Due to naturally occurring biodegradation of the petroleum hydrocarbons a large portion of the sulphate was converted to sulphide which deposited in the soils as marcasite in the anaerobic soils. The initial attempt at soil remediation was to use a forced air treatment scheme that had worked well in small scale laboratory testing. Unfortunately, when attempted in the field on a large scale, marcasite reacted with atmospheric oxygen resulting in internal biopile temperatures exceeding 90¦C resulting in the virtual sterilisation of the soils without remediation occurring. In order to solve this vexing problem Pintail Systems, Inc developed an anaerobic culture that allowed the pile to be operated under anaerobic conditions. Within three months the biopile successfully demonstrated on a large scale significant biodegradation of the refractory petroleum hydrocarbons.

Jan 1, 2004

By Bernard G, Limpach R, Ulveling L

A major aspect in competitive ironmaking is to replace metallurgical coke by injecting alternative cheap fuels. Whereas in the past, heavy oil injection as well as on a lower scale natural gas injection have proved to be reliable, the progressing high price level of these fuels has prompted international interest in looking for alternative cheaper fuels, especially pulverized coal. Theoretical analysis and practical operations showed that for constant adiabatic flame temperature, potentially more coke may be replaced by injected coal than by heavy oil, because of less endothermic cracking of hydrogen components. Since about 1974, the ARBED-Group has been looking for alternative fuels and in 1976 came to conclusion to select for first trials pulverized lignite for the following reasons:

Jan 1, 1981

By N Steenkamp, L Furstenberg, W Cele, M Richter

Managing productivity and improving efficiency for a healthy return on capital employed have become key mining industry strategies under prevailing tough global market conditions. However, achieving this in a multisystem environment such as a mining operation can be daunting. The field of discrete event simulation offers some relief, giving engineering teams insight into multivariable systems and stochastic processes. It allows for integrated system thinking and domain expertise to be woven into project thinking fibre. Directed system optimisation and therefore improved efficiency becomes possible. Furthermore, capital discipline accrues from optimal upgrade investments. This paper illustrates the practical application of this approach by reviewing a typical case study for a direct shipping iron ore operation. Dynamic simulation was used to establish maximum processing plant capacity under varying material characteristics and identify capital-efficient upgrades for increasing production.The study started with descriptive statistical analysis of existing data. Discrete equipment and system capacities were defined, followed by static plant mass balance calculations to establish bottlenecks and overall static capacity. Equipment ‘uptime’ and ‘downtime’ analyses established system and overall plant availability and utilisation. From this information, a dynamic simulation model could then be developed and initially calibrated against actual plant performance to verify its robustness. Once confirmed to accurately represent existing plant dynamics, system capacity response to variable changes could be tested to ultimately determine maximum plant capacity. Additionally, plant optimisation was incorporated to arrive at optimal upgrade points. Maximum capacity and necessary upgrades were established as a function primarily of feed size distribution. Additionally, the interfacing effects of rehandling feed material to the final product grade and potentially to life-of-mine were established as important outcomes. The results of the study illustrate the value of using dynamic simulation models to realistically and cost-effectively increase throughput.CITATION:Cele, W, Furstenberg, L, Richter, M and Steenkamp, N, 2015. Capacity evaluation of iron ore processing facilities utilising dynamic simulations, in Proceedings Iron Ore 2015, pp 597–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Shonhardt JA, Bagster DF

This paper firstly examines the pollu- tion potential of burning colliery wastes. A comparison of two means of estimating the pro- pensity for coal to combust spontaneously is next presented. The use of microwaves, as a new procedure, is discussed in detail, while a comparison of the results is made with a modi- fied adiabatic technique. A number of coals that are known to combust spontaneously was tested, as were some coals that are not consi- dered to have self heating potential.

Jan 1, 1987

By D Morgan, D Sato, B Lumsden, S Senanayake

Laboratory flotation tests on fresh cyclone overflow samples are a useful tool to troubleshoot and indeed to improve plant performance; however, reproducibility between laboratory flotation test and plant performance is important for interpretation of the laboratory tests and hence their usefulness. Chemical reproducibility can be achieved with the addition of the required reagents; however, reproducing the physics of forces and energy in a 5 L cell compared to a 50 000 L plant cell or a 500 000 L plant cell is not generally studied or discussed. For some tests such as collector evaluation the physics of the flotation process may not be critical, but for some evaluations in the laboratory, it can be important.All flotation plants suffer from losses of valuable <20 µm mineral. Selective mineral aggregation has long been recommended to improve the poor flotation recovery of <20 µm sulfide minerals; however, successfully testing any type of selective sulfide mineral aggregation’s effect on flotation recovery in the laboratory on practical plant samples requires reproducing plant cell physics. The energy input per litre and the forces in a laboratory cell are vastly different to a plant cell. Reproducibility between laboratory and plant tests requires that these differences be minimised. The physics of the laboratory flotation cell is particularly important when fine mineral aggregation tests are carried out.This paper outlines a modified laboratory aggregation and flotation method that closely reproduces plant performance in a laboratory test.CITATION:Sato, D, Lumsden, B, Senanayake, S and Morgan, D, 2014. Development of a laboratory flotation method to test plant mineral aggregation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Genge, E Martin, T Goswami, M Rothery

Rio Tinto’s Hunter Valley Operations is a large open pit coalmine situated in the heart of the Hunter Valley in Australia. The Riverview West Pit has faced increasing production challenges in recent times due to decreasing dragline strike lengths and increasing environmental constraints on vibration, overpressure and fume generation. Conventional mining techniques would involve five to six production blasts per strip to recover multiple coal seams. Each blast event carries the risk of exceeding the strict environmental requirements. By working collaboratively with Orica, it was realised that the blasting method known as Stratablast™, in conjunction with advanced computer modelling techniques, could provide productivity gains whilst simultaneously providing more control over the environmental effects and the impact on nearby infrastructure.As a result of this change, the number of blasts per strip was reduced to one, with the implication that a great deal of care and forethought was needed to manage the increased challenge posed by multiple constraints in the proposed mining area. This innovative approach of combining throw and stand-up blasts allowed the extraction of all major coal seams in a single pass blast event. The blasts were initially designed with a large factor of safety to stay within environmental limits as they were over 1.1 km in strike length, with more than 800 holes and with a total charge weight of about 1000 t of bulk explosives. Furthermore, there were conflicting priorities around the desired blast outcomes. So far, 11 such blasts have been designed and successfully fired. After each blast, innovative design changes have been iteratively implemented to provide further control over environmental impacts, whilst continuing to improve productivity. As a result of these changes, blasts have progressively increased in complexity with the inclusion of features such as damage zones, mid-splitting, time gaps and different directions of firing. The consequence of this complexity is that the blast duration can be as long as 28 seconds to accommodate all components of the blast.This project has increased the productivity of the Riverview West Pit through blast design improvements and allowed the environmental impacts to be managed with far more control and predictability than would have been possible under a conventional blasting regime. There still remains room for further optimisation of mine productivity and this is being addressed through a process of continuous improvement.CITATION:Goswami, T, Martin, E, Rothery, M and Genge, D, 2015. A holistic approach to managing blast outcomes, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 645–654 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Webb

The mining industry is relatively niche and complex compared to other global industries in its safety and operating environment. Whilst some of the technology required to decarbonise the mining industry will emerge from the mass market (eg batteries, energy storage solutions and renewable power generation) where exogeneous external investment and innovation will drive supply, bespoke applications such as material movement will be constrained by industry limitations. Underground load and haul equipment burns the majority portion of underground mine diesel, and typically 25 per cent of scope one and two emissions. Transitioning away from incumbent diesel engines offers a considerable health benefit to all mine workers, as well as decarbonisation achievements, and through trials there is emerging evidence of more productive equipment and realistic expectations of lower operating costs of fleet. However, new equipment and material movement systems that support these industry goals are currently approached with caution due to the pivotal role they play in delivering productivity goals, and the lack of experiential data and certainty to mitigate the supplier development risk during this technology transition period, where all resources are required to meet a booming industry. A group of mining companies and suppliers have the aligned aim to accelerate the understanding and availability of heavy haulage mobile equipment through collaboratively piloting equipment and working with suppliers and each other to aggregate market demand, encourage investment and resolve the mine design and technology choices through their involvement in the Electric Mine Consortium (EMC). This paper will outline the major challenges the industry must overcome in sourcing and adopting a zero-diesel particulate and zero-emission mine, drawn from cases and insights across ten EMC mining company members.

Mar 29, 2023

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By H Kim, J Park, J Lee

Silico-ferrite of calcium and aluminium (SFCA) is a bonding phase in the iron ore sinter. The phase transition upon melting of SFCA was investigated with Differential Scanning Calorimetry and Confocal Laser Scanning Microscope. The initial melting of SFCA occurred at 1183.2°C and a massive melting was found at around 1351.1–1358.2°C. A phase transition-melting was investigated at 1476.5–1478.7°C. The liquid phase was composed of immiscible phases. The present results would be utilised to design a new iron ore sinter for better processing performance in a hydrogenenriched ironmaking process.

Jun 19, 2024

By R Chinamatira

Several technical and economic factors have to be taken into consideration in developing an optimal mining method. This paper describes some of the important factors learnt during the evolution of the sublevel cave mining method at Trojan Nickel Mine, part of the Bindura Nickel Corporation (BNC) in Zimbabwe. Sublevel caving (SLC) has been successfully implemented at Trojan mine since its introduction in 1994. The method has evolved over the past six years into a system that has brought about improvements in efficiencies and productivity. Although the original design parameters used were sound and provided a solid foundation for the system, they needed to be optimised to get the best out of the mining method. Improvements and changes have been made in areas such as the drilling process, charging and blasting techniques, ring pattern design, development size and shape, and the draw control system. This has enabled the mine to develop an SLC operation that is efficient and innovative. Experience gained, together with the theory available has given us a much better understanding of the system. This knowledge will be used in the future to enhance the system further. Given the low grades of the BNC Mines, management recognises that only through technical excellence and efficient mining can the mines reduce mining costs and maintain profitability and competitiveness on the world market. In the Zimbabwe mining industry reaction to technological change, mechanisation and advancement have been relatively slow, due to isolation and economic constraints, compared to the rest of the world. Economic difficulties prevail, with high inflation levels, a poor exchange rate, lack of foreign currency and other associated problems. Despite these constraints, the bold steps taken have transformed Trojan mine into a more efficient and competitive operation, presenting itself as the leading mine in the BNC group. Appendices give data to illustrate the benefits obtained.

Jan 1, 2000

By I Zulkarnain, H Permana, R A. Binns

Through an ambitious but relatively low-cost program of marine fieldwork, laboratory investigations and technology-transfer and training activities, three Indonesia-Australia-led marine expeditions were undertaken aboard KR Baruna Jaya VIII between 2001 and 2003. These IASSHA (Indonesia-Australia Survey for Submarine Hydrothermal Activity) cruises have sought to discover and investigate a variety of potential ore forming hydrothermal systems in a range of tectonic settings. All cruises have been successful, both scientifically and from the point of view of training, creation of capabilities and capacity building for such research in Indonesia. Over 60 scientists and technicians from Indonesian and Australian institutions and agencies have been involved. Three new sites and a possible fourth site of hydrothermal activity were discovered in the Sangihe arc in northern Sulawesi. Surveys in the Tomini basin tested a hypothesis based on previous data which suggested this might be an isolated anoxic, brine-filled basin over 2000 m deep where igneous heat sources existed to generate hydrothermal mineralisation. The bay, however, was found to be open to adjacent deep ocean circulation, and there was no evidence of massive base metal sulfides. Subdued evidence of hydrothermal activity was found in the Sunda Strait associated with the famous Krakatau volcano and the extension of the seismically active Semangko Fault. The BANDAMIN program (Indonesia-Germany) covered a portion of the Banda arc in eastern Indonesia, and also found evidence of recent hydrothermal activity and epithermal sulfide mineralisation.

Jan 1, 2004

By V Seedwell, P H. McGuckin

The Broken Hill Proprietary Company Limited (BHP), started as a silver-lead- zinc mining company in Broken Hill, New South Wales, Australia in the 1880s. Since then it has diversified into the resource industries of steel, iron ore, coal, petroleum and copper. BHP World Minerals, is a Business Group of BHP which is one of the worldÆs largest and most diverse mineral resource enterprises. BHP supplies raw materials for steelmaking, copper concentrate and other mineral commodities to customers in more than 45 countries. BHP World Minerals has operations throughout the world - in Australia, the United States, Brazil, Zimbabwe and Canada. Commodities produced by BHP World Minerals currently include silver, lead, zinc, titanium minerals, platinum group metals and coal. The challenges in the improving performances in safety arena are common to our industry and BHP operations. This paper outlines the vision and values that have been fundamental in assisting BHP Cannington search for and implement a safety system addressing behavioural matters.

Jan 1, 1998

By Y Peng, B Guo

In gold processing plants, the water from the cyanidation stages is treated to detoxify cyanide species and this recycle water becomes the main part of the process water. Despite the low concentration of free and weak acid dissociable (WAD) cyanides in process water, the recoveries of gold and silver is still affected during flotation, especially when gold and silver are associated with iron sulfide minerals. This is a case at the Hidden Valley (HV) Mine. In this study, the effect of free and WAD cyanides on gold and silver recoveries by flotation from the HV Mine was considered.WAD cyanide (WAD CN) was prepared by mixing sodium cyanide and copper sulfate at a cyanide to copper ratio of 3:1 dosed at different cyanide concentrations. It was found that both free and WAD CN depressed gold and silver and particularly iron sulfides in flotation. The depressed gold and silver recoveries were closely associated with the depressed recovery of iron sulfide minerals, suggesting that free and WAD CN may not depress the flotation of liberated gold and silver minerals significantly. It was also found that 10 ppm free cyanide completely depressed the flotation of iron sulfide minerals and WAD CN depression is probably through the WAD dissociation to free cyanide species (mainly aqueous HCN) during the grinding process, resulting from a decrease in pH. Thermodynamic calculation showed that 5.5 ppm free cyanide was released in the end of grinding at an initial WAD CN concentration of 50 ppm. This research provides a guideline to counteract the negative effect of WAD CN in the flotation of gold and silver minerals.CITATION:Guo, B, Peng, Y and Espinosa-Gomez, R, 2013. The effect of weak acid dissociable cyanide on gold and silver flotation in Hidden Valley Mine, in Proceedings World Gold 2013 , pp 341-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Development of a global failure criterion for rocks has been a desired goal in rock mechanics. Due to variations in factors affecting rock specifications and their mechanical properties, proposing a single failure criterion suitable for all rock types has proven to be unachievable. The theoretical failure criteria do not fit the real data correctly. Amongst empirical criteria, the Bieniawski criterion has demonstrated an acceptable agreement with laboratory generated data. It has been experienced that the ability to estimate rock strength via the modified form of this criterion is significantly improved. Based on the modified Bieniawski criterion and using VB.net, an associated Microsoft Windows program named &apos;RAMOCE&apos; has been developed. The inputs of RAMOCE can be triaxial compressive strength data, Bieniawski parameters of a specific rock or the type of given rock. Based on input data, potential outputs of the program are Bieniawski&apos;s rock parameters, sensitivity analysis of the effective parameters, rock failure prediction and defining the type of given rock.

Nov 25, 2010

I have chosen this subject in view of the fact that, while there are many and ample opportuuities of getting reliable assays made, there are but few who are in a position to obtain reliable data on the sampling of minerals and metals my long experience at Port Pirie, where, for five years, I had charge of the Refining and Sampling Mill, showed me how important it was that a correct sample should be taken.Weighing; This, to the ordinary layman, seems so simple that no expert knowledge is needed, but in actual practice there are hundreds of pounds to be lost by the lack of knowledge in this department.(1.) There is the matter of weighing in large or small quantities.(2.) The class of weighing machine used.(3.) The accuracy of weights used.We all know that, say, 1000 tons of ore cannot be weighed in one parcel; but the fewer the weighings the less loss to the seller (and usually wishes it weighed in small lots carefully) for it is a well known fact that the most sensitive scales take a certain weight to show distinctly the indication of the balance, or, in other words, what is known as &quot;the pull of the scales.&quot; As for instance, 1000 tons weighed in lots of 1 c. each, taking the pull of the scale as being equal to 1 lb., would give a result of 9 tons loss to tbe seller, and as most of the ore sent to Customs works is worth 5. -&#163;20 per ton-this would mean &#163;180 loss to the careful man.

Jan 1, 1901

By J J. Eksteen

"In the platinum group metals (PGM) industry, smelters are often perceived as ‘black boxes’ that have to process concentrates of variable mineralogy and originating from multiple mines operating along strike or downdip from each other in the same geographical region, as is the case in the Western Bushveld of South Africa. However, PGM smelter complexes are much more sensitive to concentrate blend variation than most metallurgists or geologists would anticipate.This paper will review the impact of concentrate blends deriving from a number of concentrators processing ores from the Bushveld Igneous Complex (BIC) on smelting and converting behaviour and the constraints they impose upon smelter operation. Significant variation in behaviour is not only noted between the main mineralisation types, namely the Merensky and Upper Group 2 (UG2) reefs, but also within a given reef type. Due to the way PGMs are mineralised and finely disseminated, concentrators have to grind concentrates ultra-fine to liberate the PGMs and provide a sufficiently high-grade concentrate for smelting.The chemistry and mineralogy of the concentrates vary with the type of mine (open pit versus underground), the reef type and varies along strike; this variation impacts numerous key smelter parameters such as the base metals content, the matte fall, the converter aisle capacity, sulfur dioxide gas production, furnace matte and slag temperatures, and the accumulation of high smelting chromite-spinel minerals that has led to significant smelter upset conditions such as catastrophic furnace hearth and sidewall failures.Due to the production intensity of smelting, ie its high rate of processing per unit volume, smelters have been found to be far more sensitive to rapid variation in concentrate properties, highlighting the need for adequate blend control.CITATION:Eksteen, J J, 2016. Impact of Mineralogical Variation on the Smelting of Cu-Ni-PGM Concentrates, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 321–326 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By R Belissont, C Veloso, L Senez, F Vasconcelos, E Kleiderer, J Mesquita, Y Basselin

Mont-Wright mining complex is an important asset of ArcelorMittal located in the province of Quebec, Canada. It is composed by Mont-Wright and Fire Lake mines, operating 365 days per annum, and producing 25 Mtpa of iron ore concentrate with 66 per cent Fe. Mont-Wright concentration plant is composed by seven lines with a flow sheet encompassing AG/SAG milling, primary and secondary classification stages, spiral concentrators (rougher, cleaner and recleaner stages) and dewatering unit operations. In this context, an equation called ‘Wrec’ was developed in 1971 with the objective of estimating the mass recovery of the different blocks in the beneficiation plant and support the mining planning works of Mont-Wright complex. This equation was based on the correlation between the results of heavy liquid tests performed with drill core samples and spiral concentrators pilot scale tests, returning an estimative of concentrator yield. However, since its first development, no updates have been done in the equation, which lead to some deviations from expected recoveries in the last years. This is probably due to the changes in the process and in the ore fed into the concentrator during the period. In this way, the study presented here corresponds to the execution of heavy liquid/spirals pilot scale tests with 26 composite samples collected at Mont-Wright deposit aiming at revising and updating ‘Wrec’ equation. Based on test work results, an updated formula was established to estimate the plant recovery and a comparison performed using industrial data showed that the old formula overestimated the real yield by 5.40 per cent, on average. At the end of the study the new equation was incorporated into the mining planning process.

Sep 18, 2023

Most coal mines in Chongqing Area are highly gassy mines and liable to outburst of coal cnd methane. In order to harness mine environment and raise the Prodction capacity, methane predrainage is generally taken as a main preventive measure against outburst by all mines. In the recent ten years, the drainage volume per year has increased from 38.25 million m3 to mote than 100 million m3 with a volume over 12 m3 per tome of coal. In some mines, the draining rate is approaching to 50 percent, the rate in mining districts is up to 60 to 70 percent. The predrainage volume accounts for one fourth of total drainage volume. All these have effectively prevented the occurrence of coal and methane outbursts.This is the current situation of methane predrainage in coal mines in Chongqing area, the methods of predrainage to prevent outbursts and related parametres comprise:1. methods, technologies, supervision and effect of predrainage in different geological and mining conditions,2. the change of methane parametres pre-and post-drainage and the analysis of the effect of methane predrainage to prevent outbursts, and3. ways to improve the effect of methane predrainage.Thus the safety, reliability and production of Changqing Coal Mines will be enhanced.

Jan 1, 1991