Search Documents

By F K. Buckley

Currently, Kanieri Gold Dredging Limited operates the only large scale gold dredging operation in New Zealand. It dredges a claim in the Taramakau River using the bucket dredge 'Kanieri'. This dredge, a 'Yuba' type, was designed and built in the 1930s. On the current claim it works about 12 hectares of ground a year. Because of its design, the tailings from the 'Kanieri' make land restoration difficult. This was unimportant until it commenced its new claim ML-32-310 in 1978. The conditions, attached to this licence required it to restore the land for afforestation, the designated use fur the Crown land being mined. With the company planning to work future claims on the Grey River, it decided to undertake restoration work on the Taramakau to demonstrate its capability of establishing pasture land on tailings, a more difficult task than restoring the land for afforestation. After two years and the restoration of two blocks totalling 22 hectares, reasonable pasture establishment has been achieved. Much has been learned to date and further refinement of the techniques used will take place over the next two years. The quality of the tailings produced has improved as a result of the limited modifications possible on the existing dredge. This has been significant in achieving better results. The knowledge gained will be taken into account in future dredge design. Both the Company and its Consultant are confident of achieving satisfactory restoration of dredge tailings for pasture land.

Jan 1, 1981

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

Interaction between rock and fluid plays a critical role in rock engineering ventures such as stimulation of oil and gas wells, geothermal energy recovery and nuclear waste isolation. Robust and reliable design of the related services and underground facilities is based on understanding of the mechanics and chemistry of the coupled hydromechanical- thermochemical processes. This paper explores the application of the theory of such processes in minerals engineering, with particular reference to rockburst mitigation, in situ solution mining and cavity completion of coal-bed methane production wells.

Jan 1, 1995

By K Gardner, R Fraval, V Singh

Using new technology to create optimised infill drill programs in underground or open pit settings, it is possible to quantify the value of a drill program. The computer designed programs are optimised to uplift the most amount of resource possible into the specified resource classification, while honouring geological, spatial, equipment and budgetary constraints. When designing ‘by hand’ balancing all these factors is a time-consuming effort with no real way to determine metrics on ‘how good’ a program will be. The optimisation considers many factors allowing geologists to apply critical thinking and domain knowledge to constrain the optimisation, letting the computer do the heavy lifting of determining hole placement. Once programs have been created, they can be integrated into a production schedule. This is a critical step in determining the correct sequencing and balancing of resource availability and seeing how a program will interoperate with other tasks in the mine. For example, if drill drives are a requirement for part of the program, will they be developed in a time frame that is useful for the goals of the program? Do we risk drilling infill holes too late to add value? Do we put production at risk by not classifying parts of the model ahead of time, thus adding to uncertainty? Using software to assist with optimising and scheduling of drilling is a useful technique to save the geologists from the mundanity of manually designing drill programs and puts metrics around the effectiveness of a program and has the potential to add quantifiable value to a program. Examples will be presented that demonstrate the effective use of drill hole optimisation, comparing manual designs with optimised designs, as well as the examples that show the effective use of scheduling.

Mar 22, 2022

By H Kundapen, B R. Bolton, H Davies

The Ok Tedi porphyry copper-gold mine is located in the Star Mountains of Western Province, Papua New Guinea. Open-cut mine commenced in 1984 and is due to cease around 2010. The mine produces a total of 88 Mt of waste annually including 58 Mt overburden and 30 Mt tailings, which are discharged directly in to the Ok Tedi River. Mine derived wastes are transported downstream and deposited within the river channel in a variety of bar forms. The prevailing hydrogeological conditions including, velocity, competency, capacity, gradient, grain size and specific gravity, control the deposition and segregation of these sediments. Periodic exposure of the reactive sulfides to oxygen during fluctuations in the river discharge may result in oxidation, localised acid generation and liberation of metals into solution. To evaluate the significance of this issue, Ok Tedi Mining Limited initiated an investigation of the sediments deposited in the upper Ok Tedi River as part of its overall ARD Management Program. The specific objectives were to: evaluate the acid-forming characteristics of identified high sulfide river deposited sediments; characterise geochemically the waters in contact with sulfide-bearing river deposited sediments; map and monitor exposure areas and oxidation depth of deposited potentially acid forming (PAF) sediments; determine the depositional processes controlling sulfide distribution; and assess lag period, oxidation and metal release rates for the sediments. This work included the analysis of sediment and water samples collected on a 50 + 50 metre grid at six gravel/sand bars. The sediment samples were analysed for total sulfur, ANC, NAG, total sulfur and total copper. Water samples were tested for general water quality parameters, sulfate and a suite of dissolved metals including; Al, Ca, Cd, Cu, Fe-sol, K, Mg, Mn, Na, S and Zn. This paper presents the results of these investigations with particular emphasis on the geochemistry of the river sediments and associated contact waters.

Jan 1, 2003

By W Potma, C Brauhart, S Halley, S Urbisinov, A Scogings

Truly integrated, quantitative, 3D GEOmetallurgical (or mineral system) characterisation, classification and 3D modelling should provide a cradle to grave unifying link across the exploration and mining value chain. All too often, spatially representative (quantitative) characterisation and modelling of a mineral system is delayed until feasibility stage, incurring a significant opportunity cost. The application of robust GEOmet characterisation methods early in the project lifecycle (at exploration stage) improves ground selection, exploration, and Mineral Resource estimation outcomes, long before there is a need for metallurgical test work. The value of this early provision of quantitative 3D mineralogy models is compounded at project feasibility stage, and continues to accrue over the entire project lifecycle, delivering cost savings, improved decision making and early warning of issues and opportunities.CITATION: Potma, W, Halley, S, Scogings, A, Urbisinov, S and Brauhart, C, 2018. Putting the ‘GEO’ back in front of GEOmetallurgy: importance of early implementation of quantitative mineral system characterisation, classification and modelling, in Proceedings Complex Orebodies Conference 2018, pp 55–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

The 1980's have produced an outstanding revival of the Australian gold industry. In contrast to some previous mining booms, the economic aspects of the growth in gold production are soundly based. In general the new developments have been highly profitable and this is beneficial to all parties- whether they be government, shareholders employees or suppliers. Mining companies are showing a large commitment to gold exploration with approximately 50% of Australian exploration budgets now being directed towards gold. An increasing proportion of this expenditure is being channelled towards the eastern States with Queensland 'being the major centre of interest. Further strong growth in production is expected with some 50 projects likely to come on stream before 1990. A very significant aspect of the foundation for this growth is a continuation of the existing tax status of the industry.

Jan 1, 1987

The Douglas mineral sands deposit is located 75 km north of Hamilton in western Victoria, Australia. The deposit was discovered in the late 1990s by Basin Minerals Limited and purchased by Iluka Resources Ltd in 2002. Prestrip mining commenced in December 2004, with ore mining commencing in August 2005. Douglas is the first of several projects being implemented by Iluka Resources Ltd in the Murray Basin, with all heavy mineral concentrate planned to be treated at the companyÆs mineral separation plant in Hamilton. The mineralisation at Douglas lies along the south-eastern margin of the Murray Basin. It is hosted by marine Pliocene Loxton-Parilla Sands and consists of three discrete deposits; Bondi Main, Bondi West and Bondi East. The mineralised sediments dip at a low angle to the west and lie unconformably beneath a veneer of top soil (50 - 100 mm) and subsoil (up to 600 mm) and between three to 12 m of overburden. The barren overburden, characterised by high clay content (<53 ¦m material) generally provides a stark contrast to the sandy ore, which is between 1 m (parts of Bondi East) and 15 m (Bondi Main) thick. Both overburden and ore are removed utilising standard dry mining techniques using both scraper-bulldozer and truck-excavator combinations. All ore is delivered to run-of-mine (ROM) stockpiles before being reclaimed by front end loader into the processing plant. Grade control at Douglas is based around visual dig control aided by high precision survey, which enables accurate reference to the resource drilling and block model data. Vertical excavator faces, inclined scraper faces plus regular test pits and trenches provide opportunities for in pit mapping and sampling. This data is used to refine not only the resource estimate for Douglas but also the drilling, interpretation and resource modelling methods used for similar deposits across the basin. The foundations of the geological reconciliation process at Douglas are the in pit surveys undertaken each time the mining fleet has completed building a ROM stockpile. These surveys and the subsequent interrogation of resource models enable robust estimations of the heavy mineral content of the stockpiles, which are subsequently used to predict the daily input grades into the plant during their reclamation. Reconciliation of this daily data is then undertaken at the end of each month against metallurgical production data and plant balances. Learnings and results from the reconciliation process are used to further refine subsequent resource models and modelling methods.

Jan 1, 2009

By X Xia2, X Wang, G Liang, T Song, F Ma

Inertia cone crushers have found applications mostly in steel slag crushing operations in China. Compared with conventional eccentric cone crushers, the crusher has an obvious advantage in reducing product size. In addition, they are mostly used in two-stage open circuit crushing flow sheet, which simplifies the crushing process. However, inertia cone crushers are not widely used in the mineral processing industry due to their low crushing capacity. In this paper, the throughput performance of the inertia cone crusher was investigated in a laboratory-scale inertia cone crusher and relationships between operational parameters were identified. Iron ore was crushed using orthogonal experimental method under different machine parameters and operational conditions. The crusher throughput and product size distributions were determined. The effects of parameters such as eccentric speed, discharge gap, eccentric mass and eccentric distance on product mass flow and product size were investigated. The results of this study can help reduce the feed size of the mill in order to reduce total energy consumption of comminution.

Aug 24, 2022

Metana Minerals commenced life in 1970 and graduated to a mining company in 1981 with the opening of a small alluvial tin-tantalite mine at Wodgina (W.A.) The present board of directors assumed control of the company in 1978 and established the exploration and development philosophies that have guided the company's expansion to its present status as an emerging diversified miner. An ability and willingness to raise equity capital when required has been a feature of the company. Company activities include exploration for gold, diamonds, heavy mineral sands, polymetallic (base and precious metals) deposits, strategic minerals, rare earths, oil and gas in a geographical distribution covering the entire Australian mainland Metana owns and/or operates four gold mines (Reedy, Mt Magnet, Youanmi and Howley) and at the time of writing is developing a fifth gold mine - its first underground mine - at Rothsay. In contrast to many similar or larger sized companies, Metana undertakes most activities itself rather than through the use of consultants or contractors. In-house services include: analytical and metallurgical laboratories, plant engineering design and construction, drilling and mining (earthmoving) Metana Minerals has established an enviable reputation for technical excellence and this expertise has placed the company in a sound position to continue its growth pattern into the future. This growth will be achieved through a combination of low cost and successful exploration and acquisition of suitable mines either directly or through corporate activity.

Jan 1, 1989

A series of in situ pull tests has been conducted to determine the holding capacity of the standard SS46 Split Set Stabilisers. The experiments have been conducted in a wide range of geological conditions ranging from bedded rock to blocky ground. The results presented in this paper indicate that cement grouted split sets bolts are likely to provide up to three times the initial bond strength per metre of embedment length provided by the ungrouted bolts. The increased load transfer capacity of the grouted bolts provides an alternative for permanent excavation support using split set stabilisers.

Jan 1, 1997

A paper presenting an overview of legislative and best practice approaches to the management of OHS&E and business risk for Australian tunnelling operations. Best practice can be achieved in Australian tunnelling through ærisk awarenessÆ by decision-makers and line personnel. This will identify problems before they occur and lead to implementing controls appropriate to avoiding loss throughout the life cycle of the underground opening. The author draws on legislative approaches from all Australian states together with practical experience from risk management and risk engineering work from six recent tunnelling projects. This describes a process that:commences with concept risk assessment,involves quantification of major hazards,conducts assessments of operating risks, andleads to implementation of an integrated management system that keeps construction activities connected with the controls identified in the design and planning phases and minimises the losses sustained as a result. Key points addressed include:where the industry is going with respect to risk û methods and considerations,how tunnelling risks are perceived by the industry and legislation,how tunnel constructors and owners can minimise exposure by using proper risk engineering ætoolsÆ, andreflections on best practice methods for transferring knowledge from designers to contractors/operators.

Jan 1, 2008

By Bawden WF, Paynter JT

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopcs

Jan 1, 1998

By T Napier-Munn, D J. Bradshaw, M Chauhan, L Keeney

An important aspect of geometallurgy is quantifying mineral processing attributes, which leads to improved orebody understanding. One of these attributes is flotation performance. Several methods have been developed as indicators for flotation performance, including batch testing leading to kinetic information and the standard grade-recovery curve. This paper makes a preliminary statistical comparison between a newly proposed geometallurgical batch flotation procedure and the æstandardÆ batch flotation test commonly used to measure flotation performance in the laboratory. The new test uses much less material than the standard test, and is much faster. It is concluded that the new method follows the final recovery of the standard method well, suggesting that it will be effective in reflecting ore variability for geometallurgical purposes. Comparison of the methods based on the full grade-recovery curve shows less agreement, but this may be due to the fact that the curve is sensitive to the particular experimental set-up and conditions, which make such comparisons quantitatively challenging. Further development work is therefore planned.CITATION:Chauhan, M, Napier-Munn, T, Keeney, L and Bradshaw, D J, 2013. Progress in developing a geometallurgy flotation indicator, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 201-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

During the life of a mining project in Papua New Guinea (PNG), the greatest impact is on the people of the project area and the most intense, day-to-day contact is between these people and the project's field staff. Yet formal structures at present emphasise contact between much higher levels of national government and company personnel. Whilst understandable, this is unfortunate particularly since, given the nature of PNG politics, villagers do have a powerful influence on project success, as recent dramatic events on Bougainville have indicated. A greater role for local views and greater attention to such views by other parties is clearly required. But to achieve a successful marriage between informal village politics and the formal structures of investment procedures will require considerable patience and adjustment. This should be reflected in the cost of project development and be regarded as being as of a significance equal to that currently accorded to the technical aspects of project development.

Jan 1, 1990

By I Govender, T L. Moodley

Tumbling mills are grossly inefficient, using only 5 per cent of the total energy supplied for actual breakage. A significant proportion of this inefficiency is unavoidable owing to geometric limitations; rotating drum systems are prone to exhibiting certain regions (energy barriers) that resist particle entry thereby restricting the transfer of energy. Though such systems are inherently inefficient, improved modelling schemes may lead to slightly enhanced efficiency through better microscale predictions of key breakage drivers (stress, force). Central to achieving such incremental advances is the development of a universally accepted rheology for dense granular flows. Armed with a better understanding of these macro-scale ingredients, classical process modelling offers an efficient, spreadsheet friendly framework for recovering the spatial distributions of the comminution drivers. At this real-time level of process control, it should be possible to tune comminution operations towards more energy efficient configurations – the ultimate goal of this research. The present work employs validated DEM data to recover the full continuum field which will ultimately serve as a basis for calibrating process model outputs based on different rheological hypotheses. Such a continuumbased approach captures tensor properties like the shear stress and strain rate – both of which are necessary to developing a dense granular rheology. Moreover, DEM captures this data at the momentum transfer timescale of 10-6 s – no other measurement technique is capable of this level of spatial and temporal resolution. Importantly, the confidence in this DEM data is strengthened because it has been validated at the continuum scale using Positron Emission Particle Tracking (PEPT) kinematic measurements. Validated DEM data is derived from batch experiments conducted within a 300 mm ID laboratory drum using three and five millimetre glass beads at 60 and 75 percent critical speed; such mill speeds are typically encountered in the tumbling mill industry. Dimensional analysis is conducted using critical rheological parameters (shear rate, shear stress, granular temperature etc), which are key to not only developing a granular rheology but ultimately will be used to tune our mechanistic models.

Aug 24, 2022

By P O. Koons, R J. Norris, S C. Cox

 The Southern Alps is an active oblique collisional zone which has a characteristic wedge-shaped geometry above a low-angle ductile shear zone. The Main Divide region is a relatively low strain zone above this ductile shear zone, and is _deforming principally along steeply dipping strike-slip faults. Extensional fractures are common at a high angle to the regional structural trend. These steeply dipping structures act as conduits for gold-bearing fluids from depth, and small mesothermal gold deposits have formed at several structural levels including the near-surface region. Gold has also been deposited in a meteoricmetamorphic fluid mixing zone near a conductive thermal anomaly on the western slopes of the mountains. These various gold deposits and their well-constrained structural and tectonic settings can be used as analogues for larger, deeper-eroded mesothermal gold deposits in the Mesozoic Otago Schist belt. High level Miocene veins in NW Otago have formed beneath the main divide of the initiating Southern Alps. Late metamorphic gold-bearing veins formed as fluid escaped from the ductile-deforming crustal root beneath Mesozoic mountains.  

Jan 1, 1997

By D Craw

The Rise and Shine Shear Zone is a mineralised low angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. Rocks from the shear zone obtained from recent drillholes are unweathered and facilitate paragenetic studies. There is a progression of mineral deposition from semiductile foliation-parallel shearing, to subsequent folding, and brittle fracturing. Sheared rocks are dominated by microshears containing fine grained hydrothermal muscovite and rutile that has recrystallised from metamorphic muscovite and titanite respectively. Euhedral pyrite occurs within segregations in the schist and is locally brecciated by the shears.   Arsenopyrite occurs within microshears and is intergrown with hyrothermal muscovite. Fractures within relatively undeformed schist are filled with ankerite, siderite, chalcopyrite, sphalerite and galena and these veinlets also crosscut the microshears. Locally the schist is folded and zones of brecciation, silicification and vein deposition overprint the rock. Vein quartz and albite predominate and arsenopyrite and gold infill breccia matrix and crosscutting veinlets. Sulphide deposition began in the later stages of metamorphism with pyrite deposited in quartz-albite segregations. Subsequent shearing caused brecciation of some grains and accompanied deposition of arsenopyrite ¦ gold and rare sulphides along foliation-parallel microshears. Minor amounts of chalcopyrite, sphalerite and galena were then remobilised in ankerite veins that crosscut the shears. In areas of high strain, arsenopyrite was then deposited as euhedral grains in veins and breccias. Synmineralisation deformation caused the brecciation of some grains and gold was deposited infilling fractures in the arsenopyrite. The paragenetic sequence shows gold mineralisation occurred in two distinct sets of structures (semiductile and brittle) that formed at different times in the formation of the shear zone.

Jan 1, 2006

By L Ding, B Xu, C Wang

In this paper, we introduce the term ‘LJC’ to refer to the LJC Automatic Magnetic Flotation Separator, which is an advanced technology developed by Longi Magnet, integrating various techniques such as hydro separation, magnetic flocculation, and magnetic columns. This technology combines gravity, hydro separation, and magnetic separation to achieve efficient and reliable separation processes. With its low maintenance requirements and high reliability, the LJC technology has proven to be effective in magnetite processing. The LJC technology offers two primary benefits when compared to traditional magnetic drum separators. Firstly, it can enhance the quality of the targeted or improved concentrate at a coarser product size by minimising the carryover of gangue minerals into the concentrate. Secondly, it can significantly improve the concentrate quality (eg achieving >67 per cent Fe) while maintaining similar liberation size and mass yield. In China, this technology has been widely adopted in magnetite processing, replacing traditional magnetic drum separators and fines flotation in the final stage of the process. Through collaboration with a magnetite producer in Western Australia, Longi Magnet successfully implemented the next-generation LJC Automatic Magnetic Flotation Separator to replace the original stage 3 magnetic drum separators. The application of the LJC technology resulted in an increase in product P80 from 32 μm to 43.1 μm, while maintaining a final concentrate grade of 65 per cent Fe. Additionally, the power consumption, measured in kWh per tonne of concentrate, was reduced by 10 per cent. By eliminating the bottleneck caused by the requirement of a coarser liberation size to achieve the desired concentrate grade, the plant’s throughput was increased by significantly. The LJC technology has demonstrated its ability to reduce the carbon footprint, improve concentrate grade and enhance mass recovery, offering an alternative solution for magnetite processing. The high-grade magnetite produced by the LJC technology is particularly suitable as a raw material for Directed Reduction Iron and green steel production. This paper introduces the principles of the LJC Automatic Magnetic Flotation Separator and provides details of its application in a magnetite operation in Western Australia.

Sep 18, 2023

By P Luo, J E. Danoczi, P Nakutnyy

Sensor-based sorting methods to remove waste or for upgrading ore prior to downstream metallurgical processing is becoming more prevalent for mining operations. X-ray transmission (XRT) sorters are a popular choice for mineral processing plants since they can sort a wide variety of minerals. XRT sorters pass high intensity X-rays through particles to generate images of varying greyscale, based on their effective atomic density. The ore sorter then mechanically separates the particles using algorithms based on the images. A popular test currently used to evaluate the amenability of the ore to XRT sorting is to pass the particles through the sorter and obtain the greyscale images showing mineralogical differences. This test provides information on the mineralogical heterogeneity between ore particles for their separation. However, it does not provide an understanding of the actual mineralogical composition of the ore or information pertaining to which other minerals may respond in a similar manner, nor does it provide liberation information. This paper describes a test that combines high resolution X-ray micro Computer Tomography (CT) combined with QEMScan to obtain information about amenability of ore to XRT sorting and to obtain valuable information that can streamline metallurgical testwork programs. This test also provides information relating to particle thickness and associated X-ray attenuation coefficients, desired mineral presence and mineralogical information relating to associated minerals and clays to assist with developing sorting algorithms. Combining the CT and QEMScan can address many limitations of the current method to determine whether XRT sorting technology is appropriate for particular ores. Mineralogy information from QEMScan can identify incidences of; mineral encapsulation, problematic clays, detrimental minerals as well as calibrate the greyscale values of CT data. Additional 3D CT imaging carried out on cores provides spatial information of the minerals within the ore and mineral grades.

Nov 10, 2020