Search Documents

By V Matousek, A Sellgren, R Visintainer, G McCall

A 4-component model for settling slurry pipe flow has been previously described by Wilson et al (2006) and Sellgren et al (2014) to predict pipeline friction loss (hydraulic pressure gradient) over a range of slurry compositions: from fine to coarse particle size, narrow to broad particle size distribution, and low to high solids concentration. The method applies a weighted average of established pipeline models for various settling slurry flow regimes, according to the volume fraction of solids falling within the applicable size range for each model. Further development of the model was undertaken by Visintainer et al (2017a, 2017b), based on a comprehensive set of laboratory tests in 203 mm (8 inch) and 103 mm (4 inch) pipelines, and it was also adapted to the modelling of slurry pump performance derates. However, this work was all performed with solids having a specific gravity near 2.65, as is typical for many mineral processing and dredging applications. The goal of the present work is to test the applicability of these models for settling slurries having a higher solids specific gravity, as may often be seen in the mineral processing of iron ore deposits. To that end, a test program was carried out in a 103 mm (4 inch) pipe loop using various compositions of an iron ore product having a solids specific gravity of 4.75 and containing both coarse and fine solids. By screening and flushing operations, a range of particle size distributions were created having different proportions of the coarse and fine elements. In all, 19 tests were performed with d50 particle sizes ranging from 50 μm to 3.2 mm and delivered solids concentrations from 10 per cent to 43 per cent by volume. Particle size distributions varied from very narrow to very broad, with d85/d50 ratios ranging from 1.75 to 26. Pipeline pressure gradient and pump performance data were collected and used to test the applicability of the previously developed 4- component models and to propose improvements to the models for the handling of high-density solids.

Nov 8, 2021

By U Singh

This paper presents the evolution of the studies and strategic plans to extend the life of operations at the Savage River iron ore project in north-western Tasmania. The current Life-of-Mine (LOM) plan for the Savage River operations is based on a series of open pits. Drilling has confirmed high-grade extensions of the magnetite resource at depths that exceed practical limits for open pit mining. Grange Resources Limited, the owner of the operation, is investigating underground options – not only to extend the LOM plan but also to maintain peak production at a reduced operating cost while reducing greenhouse gas emissions into the future. What makes this project unique is that it requires introducing a productive and cost-effective mining method to exploit a challenging geotechnical and geometrical orebody in an area of high rainfall. To support the study efforts, the development of an exploration decline, underground drilling programs, and an exploratory drive excavated into the orebody for geotechnical investigation was key to providing the necessary data for a pre-feasibility study (PFS). This paper describes the pragmatic approach and processes to developing the underground mining options study through data collection and then integrating these options into the open pit plans to optimise an overall strategic plan for the Savage River operations. The learnings for operators from this experience are how the technical and pragmatic approaches were aligned to develop the strategic plans, and the importance of timely investment in gathering the necessary data.

Mar 29, 2023

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998

By T Zhao, K Wang, Z Zhang

Tailings pond safety monitoring is vital for preventing dam failures and ensuring environmental safety. Unmanned Aerial Vehicles (UAVs) can enhance tailings pond monitoring with flexible operational cycles and the ability to collect remote sensing data from inaccessible areas. While many mining operations have adopted UAVs for tailings pond management, their full potential in data acquisition and subsequent analytical processing remains largely untapped. This paper explores various case studies where UAVs have been utilised for monitoring key aspects of tailings ponds such as beach line indicators, dam displacement and erosion, slurry discharge processes, and tailings pond capacity. We also present examples where data derived from UAVs have been instrumental in slope stability analysis, seepage modelling, Tailings Dam Breach Analysis (TDBA), and risk prediction. By integrating UAV technology with traditional ground-based sensor techniques, this approach significantly enhances the precision and reliability of hazard prevention and management in tailings pond operations.

Sep 1, 2024

International tenders for contract mining opportunities require the Contractor to make an assessment of risk for an operation with a life span of up to twenty-five years usually based on data made available by the Client. This paper seeks to address how the Contractor assesses the data and quantifies the risks associated with the project. The areas of risk are common to most projects, but in the--Lontractor's case, risk assessment is carried out on the Client's data base and within a compressed time frame of usually less than six months. Incorporation of that risk assessment into the contract documentation is also discussed. Practical examples are given in a number of areas.

Jan 1, 1986

By D McLaughlin

This paper points to the timely importance of commencing a centrally recognised perpetual collection of mineral specimens in the Northern Territory which has as one of its objectives the collection and preservation of Northern Territory minerals of scientific, educational and heritage value. Currently in the Northern Territory there is no government department or institution that has a resourced coordinated state-wide objective to collect and document collectable mineral specimens. Specimens held in storage by the Department of Mines and Energy and the Museum and Art Galleries of the NT are not catalogued and owe their existence to fortuitous circumstances, not as a result of a planned systematic scientific approach to mineralogy. Northern Territory mineral species and unique specimens have and will continue to be driven to extinction while no central and active, recognised repository exists. This situation persists despite the fact mineral production is the Territory's largest income earner. The paper presents the arguments that hopefully will assist decision-makers to commence development of a state mineral collection lodged within an appropriate institution in the Northern Territory.

Jan 1, 1994

By X Sun, L B. Zhou, H Yi, X Tang, P Ning

The rapid industrialisation in China has consumed large amounts of various industrial raw materials, which has left behind large quantities of industrial solid wastes produced from the processes of mining, mineral processing and smelting. The storage of huge quantities of industrial solid wastes is an obvious risk to the environment and human well-being. As the first step to fully appreciate the scale of this risk, it is necessary to carry out research for developing a pollution source environmental risk assessment system (PSERAS), especially for the typical staple industrial solid waste (TSISW). This paper aims to discuss the frame of the PSERAS for TSISW for large scale production. This system consists of two aspects: predicted factors and accidental ones, which involve physical, chemical and biological risk assessments, on-site and during transportation process. Two analysis methods, the analytic hierarchy process (AHP) and fuzzy logic assessment (FLA) were used to handle the complexity of environment and non-quantitative data. The risk assessment system for such a complex objective is difficult and the assessment of relative factors is problematic through the usual quantitative analysis. With the proposed PSERAS, it is possible to define the risk class of pollution sources. Furthermore, the risk assessment results will be helpful to the decision-maker, especially when facing unknown risks in the environmental management of industrial solid wastes. In addition, by means of the PSERAS, risk factors can be ranked against their contributions to environmental risk, in order to calculate their relative priorities in decision-making.CITATION:Sun, X, Ning, P, Tang, X, Yi, H and Zhou, L B, 2012. Environmental risk assessment system for typical staple industrial solid wastes, in Proceedings Life-of-Mine 2012 , pp 301-304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By G Chitombo, A Perryman, A D. Campbell, J White, B Hollis

This paper describes the development and implementation of an optimisation tool developed as part of the Mass Mining Technology (MMT) Project. The tool, known as the SLC Schedule Optimiser, is capable of optimising the schedule of development and production activity for a sublevel cave, given a fixed draw strategy, for the life of the mine.This paper starts by describing the development and production scheduling problem for a sublevel cave, the geotechnical constraint that a schedule of activities must adhere to, and outlines the pre-existing manual planning procedures used to produce schedules.Following this, the paper then outlines the optimisation tool developed, describes the changes to the planning process it has enabled and finally quantifies the improvement to operations this tool has brought using Glencore’s Ernest Henry Mining Operations as a case study.CITATION:White, J, Perryman, A, Campbell, A D, Hollis, B and Chitombo, G, 2016. Life-of-mine development and production scheduling optimisation for sublevel cave operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 133–138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By T Niitti, J Turunen, P B, A Rinne

In todayÆs marketplace, with high metals prices, many operations are faced with the challenge of improving recovery in the particle size ranges which are normally difficult to recover. This presentation focuses on the various methods used to alter the flow dynamics in a mechanical flotation cell, thereby improving metallurgical results. Modern computational fluid dynamics (CFD) tools have been used in the design phase, with subsequent validation at the plant. Some of the validated variables include mixing profile, power draw and local air hold-up. This presentation underlines how modern CFD analysis can be used to screen and select different approaches before commencing costly trial-and-error experiments at plant scale. Two methods of affecting flow dynamics are discussed û firstly, by altering the geometry of the rotor-stator area and, secondly, by fitting additional features in the tank. The rotor-stator area can be modified to provide more concentrated turbulent kinetic energy or, respectively, to provide more pumping efficiency with less attrition. The tank can be fitted with various additional features, aimed to create different particle suspension profiles. The benefit of both methods is that they can be applied not only to newly installed flotation technology, but also to existing plant cells, thus enabling potential improvement in the mixing profiles, solids suspension, tank sanding and metallurgical performance. Results of several sitesÆ tests are discussed in terms of flow variables measurement as well as metallurgy. This paper demonstrates the effects of different flow dynamics on the mixing profiles and metallurgical results of existing mechanical flotation cells.

Jan 1, 2006

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium.One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives. Controversy can always be achieved by producing a best of list; it can be guaranteed that everyone will disagree with at least one of the nominations. On this occasion, the best contributions by individuals or groups in a number of areas of mine fill technology, over the last 25 years, will be the basis for the nominal awards. The controversy can be increased by posing a number of questions that, hopefully, some of the authors will address during their presentations. I imagine the social functions will be busy enough, but the questions may just add to the cut and thrust of the debate.

Jan 1, 1998

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R Schlueter, H Mischo

The mining industry is facing a variety of geological, technological and social challenges. Future deposits show a general tendency towards increasing depth with complex ores and decreasing grades. One promising approach to deal with low-grade ores is bioleaching in the form of heap and dump operations. Bioleaching is already a state-of-the-art technique, especially for the extraction of copper from sulfide ores. The next step in the development of this technology will be its application as an in situ technology. First attempts to adapt this technology in underground mining in the form of stoping and block caving have already been made. Both methods have to be carried out adjacent to conventional mining operations and therefore require much effort regarding drift development as well as extraction and transport. The adaption of bioleaching as a borehole mining method is the next step to establish an innovative in situ technique to meet future challenges.The Freiberg University of Mining and Technology established the Biohydrometallurgical Centre for Strategic Elements (BHMZ) to foster interdisciplinary research along the whole biohydrometallurgical process chain. In general, 13 different university institutes and several associated groups with about 30 PhD students are mainly focusing on the extraction of indium and germanium from deposits, tailings and recycling material. One of the core projects within the BHMZ is the design and implementation of an underground in situ bioleaching testing facility.This paper demonstrates the potential of in situ bioleaching under technological aspects. Furthermore, different conditioning methods to increase the permeability of the orebody will be explained, and the BHMZ’s underground testing facility will be presented.CITATION:Schlueter, R and Mischo, H, 2015. Potential and applications of underground in situ bioleaching, in Proceedings Third International Future Mining Conference, pp 205–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By M Hawkes, Z Ji Gang, Z Ming, R Hassell

As underground mines become more geotechnically challenging with increasing depth and excavation size, the requirement for ground support to be installed as per design becomes more critical. The verification of installation quality for cable bolts and grouted rock bolts is difficult to assess. Current methods to control quality have limitations; pull testing is largely inconclusive with only extremely poor installation being identifiable. Audits during installation can only capture a small percentage of installed bolts. Following large rock mass displacement from either squeezing ground or seismic events, even previously well installed bolts may have yielded and require replacement. A method to provide an improved understanding of the reinforcement installation quality is Non- Destructive Testing (NDT) using acoustic reflection. To validate the accuracy of an NDT system, both plain and bulbed strand cable bolts were grouted in clear plastic tubes. The encapsulation grout quality was deliberately varied from full encapsulation through to partial encapsulation and a range of different size voids. The clear tubes allowed the ground encapsulation to be observed. Cable bolts strands were cut at varying lengths and different water cement grout ratios were used. Acoustic testing of the cable bolt specimens was completed blind; the technicians were not aware of what was being tested. The NDT results correlated well with the grout encapsulation, with differences between full encapsulation, minor voids and major voids being determined. The different water cement ratio and bolt lengths (including when partially cut) were also identifiable but with some discrepancies. Trials of the technology underground have also shown the data collection process to be relatively quick with each bolt taking 1-2 minutes to test, with interpretation of the results able to be completed soon after. The NDT results collected from the underground trial showed a wide variance in cable bolt grout encapsulation quality indicating that there were installation issues.

Mar 15, 2021

By G R. Hancock, J F. Martín Duque

Post-mining landscapes are required to geomorphologically and ecologically integrate with their surrounds (Martín Duque et al., 2015). Designing and constructing an erosionally stable landform is the first and arguably most important part of the rehabilitation process. Without an erosionally stable landform topsoil and nutrients are lost, shallow groundwater is depleted as well as when excessive erosion occurs, expose suboptimal materials. Here we examine the ideas of geomorphic design and rehabilitation and how the landform can be tested and enhanced using computer based design and landscape evolution models. Specifically we evaluate the complementary capabilities of landscape modelling (SIBERIA) (Hancock and Willgoose, 2017) and geomorphic design software (Natural Regrade with GeoFluv) (Bugosh et al., 2016), in order to maximise erosional stability on post-mining landscapes (Zapico et al., 2018). CITATION:Hancock, G R and Martín Duque, J F, 2018. Geomorphic design and landscape evolution modelling for best practice mine rehabilitation, in Proceedings Life-of-Mine 2018, pp 119–121 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By D L. Reid, G Nwaila, J Petersen, J-P Franzidis, Y Ghorbani, M Becker, F C. de Beer, L C. Bam

Traditional methods of gold extraction have involved comminution and processing via cyanide leaching, all of which are associated with energy, cost and environmental implications. Subsequently, numerous opportunities for improvement and optimisation strategies in gold mining and processing have been explored, including heap leaching, which has significantly lowered comminution costs. This paper explores the effect of the more energy efficient high-pressure grinding rolls (HPGR) on the comminution behaviour (especially on the crack density) and cyanide leaching performance of laboratory reactors study on run-of-mine gold ore comprising the Ventersdorp Contact Reef (VCR) and the Elsburg Reefs (ER), sourced from Carletonville in the Witwatersrand Basin in South Africa. The ore was comminuted using HPGR at three different pressure settings (120, 90 and 60 bar). Large (-16/+11.2 mm) and small (-5.6/+4 mm) particles of the HPGR product where then mineralogically characterised using optical microscopy, quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) and X-ray computer tomography (CT) before cyanidation. The results of the leach experiments indicated a correlation between gold extraction, particle size and crack density. Mineralogical characterisation of the ore indicates that the Fe-sulfides present in the VCR are likely to be more reactive than those in the ER, thus having a more favourable influence on gold cyanidation. Overall, the results show promise for the heap leaching of Witwatersrand gold ores prepared using HPGR and demonstrate the value of a multi-disciplinary geometallurgical approach.CITATION:Nwaila, G, Becker, M, Ghorbani, Y, Petersen, J, Reid, D L, Bam, L C, de Beer, F C and Franzidis, J-P, 2013. Morro do Ouro geological model with a metallurgical view, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 75-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By H W. Wu

Occupational exposure limits for diesel particular matter (DPM) are progressively being adopted in a number of countries. Many of these follow the lead of the US Mine Safety and Health Administration initiated in 2008. In line with adoption of best practice it is accepted that all exposures should be reduced to as low as reasonably achievable. The management of diesel emissions and occupational exposures to those emissions requires an integrated strategy incorporating efforts from all key departments on a mine, including management, production, maintenance, supply and occupational health and safety.Australian coalmine longwall moves rely on the use of high-powered diesel equipment such as chariots and other machines that produce exhaust pollutants of gases and DPM. To reduce mine personnel’s exposure levels to DPM a hierarchy of controls can be followed. Minimising the use of diesel equipment, better operator positioning in relation to exposure source, using efficient engineering methods and adopting better ventilation to reduce concentrations through dilution are some of the controls that can eliminate exposures. Approaches generally adopted in Australian longwall mines currently rely on a combination of strategies such as optimisation of ventilation, use of diesel particulate filters and use of diesel tag boards that minimise the number of vehicles through recording entry and exit into working panels.A study has been undertaken into the mine ventilation systems currently in use during longwall moves within Australian modern longwall extraction mines. This paper reviews current longwall section ventilation systems and discusses evolving changes being adopted to address the more complex problems in dealing with section DPM during phases of the operational moves. The effects of DPM on crew members as well as the diesel equipment operators within a longwall section are examined. Issues that should be considered in designing the longwall section ventilation during the moves are discussed.CITATION:Wu, H W and Gillies, A D S, 2015. Review of ventilation optimisation strategies during longwall moves, in Proceedings The Australian Mine Ventilation Conference, pp 133–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Laurence, L Ge

This paper demonstrates use of remotely sensed imagery in promoting sustainable mining. Remote sensing technology can be used during all phases of a mining project û from evaluating the resource, to making extraction more cost-effective, through to monitoring, mine closure and remediation. Use of the new generation of satellite platforms with the capability of acquiring satellite data with higher spectral and spatial resolution have the capability to emerge as essential indicator for sustainable development in the minerals industry. A life cycle approach to satellite imagery is discussed. The use of an imagery of the site prior to mining activity establishes the environmental baseline, guides mitigation measures and eventual help in suggesting remediation. Remote imagery provides the cost-effective means of monitoring reclamation, including the growth of planted vegetation, of the mine site and surrounding area. The latest advancements in satellite remote sensing are highlighted to meet the newer challenges of sustainable mining practices. Some of the worldwide successful remote sensing applications for the measurement and evaluation of the sustainable development impact of mining operations are described. Presently available source of imagery and its comparative advantages and disadvantages are provided as a guide. Finally, the limitations of this tool are indicated.

Jan 1, 2009

By M Stephens, T A. Sutra

Currently, there are several open pit mines with production rates of about 200 000 tpd of ore that are reaching the end of their economic lives. In most cases, the remaining orebody extends to depths greater than 300 m below the pit limit, leaving hundreds of millions of tons of reserves that can only be recovered by means of an underground mining method. One such method used for mass production is block caving. This paper presents a ventilation system for a four-zone block cave mine operation developed on a footprint 1000 m wide and 1200 m long. The system is designed for a mine with a nominal production rate of 120 000 tpd of ore using diesel powered units on the production and reduction levels. It discusses the air quantity requirements for the worst case scenario, which is anticipated to occur five years after the mine has reached its full production capacity. Finally, it summarises the results of computer modelling exercises that were carried out to determine an economic ventilation infrastructure that includes shafts, drifts, main fans, and ventilation control devices.

Jan 1, 2005

By D Whitworth

The Golden Pig mine has embarked on a diamond drill program design philosophy that increases flexibility of the program by greatly increased drill pattern densities. The use of standard broad pattern diamond drilling at the Golden Pig mine has previously lead to operational inefficiencies and impacted significantly on the costs of the mine. The diamond drill program philosophy and its interaction with mine planning is explained. The case study of the E lode mining as used to internally justify the increased drill densities is detailed.

Jan 1, 2002