Search Documents

FOR some time it has been recognised by the Metallurgical Staff that the presence of pyrite in the ore was adversely affecting the grades of the flotation concentrates.Following experimental work, it was decided to change over from the acid circuit in the mill to an alkaline circuit. The following description sets out the procedure adopted, -and the results obtained when such change-over was made.The Zinc Corporation ore consists mainly of galena, marmatite, calcite, and quartz, with smaller quantities of pyrite, fluorspar, and rhodonite.A clean specimen of marmatite picked from the ore assayed 53.4% zinc, and 10% iron, with no lead or insoluble. However, as zinc concentrates have been, at times, produced in the plant assaying over 53% zinc, and with only 8.7% iron, apparently the picked specimen of marmatite did not represent an average composition.The average would probltbly be between 8 and 9% of iron, and from 53.5 to 54.5% of zinc. It is obvious, therefore, that from this ore it is not possible to produce zinc concentrate of a higher grade than this average figure.In the Colorado School of Mines Quarterly for April, 1928, Vol. 23, No. 2, on page 47, we find the following statement:As the zinc in the ore exists as marmatite, which contains approximately 54.5% zinc and 10% iron, 49% zinc in the concentrate may be considered high.This statement refers to the ore treated in the Sullivan concentrator, owned by the Consolidated Mining and Smelting Company of Canada Limited.

Jan 1, 1930

This paper describes an ongoing study into the management systems developed by mining operations in Papua New Guinea to address particular public health issues in the workforce (primarily communicable and lifestyle diseases). The first stage of the study involves the analysis of the site health and safety management system documentation of three major mining operations in Papua New Guinea, producing a descriptive summary of each system. In the second stage of the study these summary descriptions are evaluated using a maturity model constructed through a detailed review of literature. Experience with the evaluation process is then used to refine the maturity model. The analysis performed in the study is used to develop a process for creating a maturity model for mine site health risk management based on a theoretical risk management framework, and refining it through empirical evaluations of the actual systems in place on site. Companies can use maturity models as a guide to organisational improvement, which in the context of the study will assist the operations in developing their systems for the management of health both in their workforce and in local communities.

Jan 1, 2007

By J A. Shonhardt, I Porter

All types of coal are liable to spontaneous combustion to a variable degree according to the inherent characteristics of the coal and also extrinsic factors. In order to successfully extract coal from highly capital-intensive longwall mining operations it is necessary to evaluate and manage any risks that may be present due to spontaneous combustion. A spontaneous combustion risk management plan for longwall mining is described in this paper. This risk management system comprises identification of conditions promoting spontaneous combustion risk, a laboratory or empirical risk classification system, determination of gas ladder, adoption of adequate ventilation plans and gas monitoring systems that will lead to the development of the spontaneous combustion action plan. The risk management system was applied to a greenfield site in NSW in 1992 when prediction of a high-risk category for the coal seam was made. After commencement of production a spontaneous heating problem emerged as predicted. Description of the case history of spontaneous combustion risk management for a longwall operation in this coal seam is included in this paper.

Jan 1, 2003

By D Brett

The Paper presents the authors thoughts on how the mining industry should be improving the education of site personnel so they can provide a greater level of effective control of tailings dam safety including empowerment to develop their own documentation, monitoring and surveillance systems and to better liaise with specialist external technical staff or consultants.

Jul 1, 2021

Macraes Mining Company Limited operates a 2.1 million tonnes per annum gold processing plant at Macraes Flat, Otago. This uses a conventional CIL route to treat oxide ore, and a flotation, grind, CIL route for sulfide ore. This paper describes the design and operation of this process plant.

Jan 1, 1992

By F Tang, Ö K. Büyükuslu, M Baben, S Petersen

GTT-Technologies’ ChemApp for Python was developed to provide a powerful, easy to use interface to ChemApp for a programming language highly popular with scientists and engineers. It is used, for instance, by GTT to develop program modules such as the CALPHAD Optimiser for the FactSage™ software, by customers to move from interactive FactSage calculations to perform versatile scripting with Python, and by GTT and its partners in research projects in the area of materials informatics. Computational thermochemistry is fundamental for advancing sustainable metallurgy and creating new alloy compositions for engineering applications. Materials informatics involves handling vast amounts of data and complex workflows. GTT’s approach uses ChemApp for Python and the FactSage thermodynamic databases to design recyclable alloys from the start, incorporating a higher percentage of scraps while aiming to simplify the workflows to simulate material design steps. Challenges arise due to recycling scraps, introducing more elements for consideration. CALPHAD-based databases accurately cover materials from primary metallurgy, but additional data for minority and critical elements is crucial for precise computational modelling. GTT combines machine learning-based ab-initio databases with traditional CALPHAD databases to cover the complete chemical space with appropriate accuracy. The design of a hardfacing alloy through a high-throughput materials informatics approach is used as a demonstrator of the current possibilities.

Jun 19, 2024

By A Winchester, D Grant

The massive 1100 Orebody in Mount IsaÆs X41 Copper Mine has been extracted over the last 40 years form north to south utilising sublevel open stoping methods.De velopment has continually stepped ahead of production to provide access to new primary stoping blocks. The remaining secondary pillars contain stopes with one, two or three fill mass exposures and were constrained by access requirements and stope extraction turnaround time.The remaining southern mining areas consist of large 40 m wide by 300 to 400 m long east-west transverse pillars that have been left to provide access for ventilation and service requirements. Three large transverse cross-cuts or transverse pillars û 4180 x/c, 4010 x/c and the Panel pillar now remain. The 4180 x/c was the last major transverse pillar to be successfully broken.This transverse pillar is being extracted in a retreating sequence, creating 3SLOS stopes due to the surrounding backfilled stopes.In recent years the extraction of the first, and most critical, stopes in the transverse pillars have resulted in large changes to the induced stress field. This paper describes the extraction of the 1.1 million tonne stope P418 in the 4180 x/c pillar.T echnical challenges that were faced and how they were overcome to allow for the successful extraction of the stope are described.Critical to the success of the P418 stope extraction were the rehabilitation methodology used; extraction strategy modifications to address deteriorating ground; mass firings with multiple directional changes; managing the exposure of backfill of variable strengths; and geotechnical monitoring prior to, during and after extraction.

Jan 1, 2005

In 1955 the annual production of steel at Australian Iron and Steel Pty. Ltd., Port Kembla was 1.2 million tonne and over the following two decades this had progressively increased to the present capacity of 5.4 million tonne per annum. This increase in productivity has also been accompanied by important developments in steelmaking technology and these are explained in the chronological order in which they have taken place. Reference is made to the use of oxygen in open hearth furnaces, the B.O.S. process, the Argon-Oxygen decarburisation process for stainless steel, vacuum degassing and continuous casting. When the vacuum degassing and continuous casting units are commissioned, the Port Kembla Works will have achieved a standard of steelmaking technology equal to any in the world.

Jan 1, 1976

Previous published papers by Fraser (1), Hey (2), and Stillwell (3), have given respectively, details of:-1. The practice in the pilot plant operated at Zeehan for the treatment of ores from the Rosebery field.2. The design, based largely on the experience gained at Zeehan, of the concentrator built at Rosebery.3. The nature of the orebodies of the zinc-lead lode at Rosebery.Changes and developments, at the Rosebery concentrator, since operations commenced, are now described with particular reference to recent practice.Three concentrates are produced, viz.: a copper, a lead, and a zinc concentrate. The current flow-sheet is shown in Fig. 1. Typical concentrate assays are...THE OREThe ore treated is derived from the Rosebery and Hercules Mines and is, milled in the ratio of, approximately, two parts of the former to one of the latter. The ores from the two mines may be considered as being similar in general character, although the Rosebery ore contains more pyrite. It is from this mine that any increased tonnage is expected. The ore is a mass of fine-grained, intimately associated sulphides, with practically no coarse...

Jan 1, 1949

By P Jackson, J Rea, M D. Goodz

The Morning Star Gold Mine has operated over a 101-year period, producing gold from narrow quartz veins and sulfide stockworks hosted mainly within a dioritic-gabbroic dyke. The deposit has been developed over a vertical depth of 980 m with drilling extending the vertical depth to greater than 1200 m. Currently there is a total Inferred Resource of 4.6 million tonnes at a grade of 6 g/t for 910 000 ounces of contained gold resources, which comprises an underground project and a surface project. Significant variation exists between the grade of drill core intersections and that observed in face sampling and subsequent production reconciliation (250 - 650 per cent). Studies were carried out on ten major production reefs, where the grades of drill intercepts were compared with face samples collected during development and mining. The implications of this study have been used as justification to assign production or stope/development grades where applicable to resources that are direct extensions of the historical development headings. Grade assignment and its impact on sensitivity for gold resources are detailed and show a 40 per cent variation in the gold resource, depending upon whether a production or calculated stope grade is used in grade assignment for the major reef deposits. Recent diamond drilling has intersected approximately 40 new gold bearing quartz reefs and sulfide zones that contain all the key mineralogical and structural indicators, and traditional large variations in gold grades similar to the historical major production zones. The implications of grade factoring and grade assignment are the greatest challenges confronting the resource estimation team in defining grade for these new zones. Grade assignment is seen as a method of balancing known historical production observations with the irregular grade distribution inferred from drill core assay results. Ongoing mine development and bulk sampling works are planned to validate the grade assignment process. The first stage of this process is the trial mining of the newly discovered Maxwell Reef (MR). The stope drawpoints were completed in August 2008 and the MRS1 stope is scheduled for completion in September. The stope reconciliation results will be presented at the October 2008 conference.

Jan 1, 2008

Techniques have been developed for the dissolution of a wide range of rocks and minerals by a sodium peroxide sinter process. A olarge number of elements are determined by atomic absorption spectroscopy, and other elements such as arsenic and sulphur are determined by chemical analytical methods. The methods adopted to overcome inter-element and ionization effects on the atomic absorption results are discussed.

Jan 1, 1974

By Turnbull AG

The direct smelting of zinc sulfide con- centrates has been investigated by an extensive series of computer-based thermodynamic equili- brium calculations. The study covers both pure 7.n-S-O-C-N systems and practical concentrate- coal-air-flux systems. It is shown that for a zinc concentrate containing iron and lead sul- tide impurities, a 97% yield of zinc vapour with autogenous operation can be obtained under carefully optimized conditions. The possible integration of this process with existing zinc condensation and recovery processes is Discussed.

Jan 1, 1980

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs.A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanized mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximized, cost if reduced and all profit opportunities are optimized. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

In process industries, time-dependent random fluctuations of raw material characteristics and mass flow rates in bulk material or pulp flows cannot be always prevented for different reasons, eg because of the geological situation (no uniform formation of the deposit) or/and because of technological reasons (segregation in bunkers or on stockpiles). Since a long time, there has been practical experiences that such fluctuations can have negative consequences, eg: ò fluctuations of the final products characteristics, ò higher expenditure for process control, and ò worsening of technological characteristics (recovery, sharpness of separation etc). In the literature, there can be found a lot of details as to, eg the improvement of the sharpness of separation in a jig in dependence on the raw material blending (Kubitza, 1981; Gathen, 1983) or the decreasing flotation recovery with increasing raw material characteristics fluctuations in iron and potash ore processing plants (Bubnova, 1978). Up to now, however, these consequences of random fluctuations, eg on the separation efficiency were not predictable theoretically. It could be shown by means of the general model for mechanical macroprocesses (Graichen, 1989), that the reduction of input fluctuations passing a blending facility can be calculated in this way. In this example, the steady state of the process is the wanted one, but, in general, the model is able to describe also non-steady states of the process regarded. On the other hand, the general model of mechanical macroprocesses has been used successfully for modelling separation processes, eg cross-flow and air classification (Molerus, 1969; Neesse, 1991; Senden, 1979; Tichonov, 1973). That is why it was tried to model the influence of input fluctuations on the separation efficiency, that means, the impact of non-steady states - as a consequence of random fluctuations - on a separation process. The models discussed in the literature are related nearly exclusive to the steady state of the process. The reasons for that lie in the (relative) simplicity of the models and the fact that the steady state is aimed at by means of blending processes under practical conditions - because of the advantages mentioned above. These models cited have proved to be superior to other models, since the basic general model for mechanical macropocesses makes possible the consideration of turbulence acting in the process unit and influencing the separation process essentially. This is valid also for modelling the turbulent cross flow classification, applied to mechanical classifiers and hydrocyclones, where the correspondence between the separation characteristics (cut size, separation sharpness) calculated and determined experimentally is much better than for other models.

Jan 1, 1993

The success of smooth blasting essentially depends on geological condition of rock. Also, in the perimeter hole, borehole pressures with light, well-distributed explosive loads are important to minimise overbreak. In order to simulate perimeter holes with scaled model test, the borehole pressure was considered as a factor of scale. Hydraulic oil pressure is applied as borehole pressure instead of using explosives and detonators in order to remove the undesirable effects of detonators in an experimental set-up of just two perimeter holes in a tunnel blast. The borehole pressure on a perimeter hole is nearly reproduced with hydraulic pressure which is generated by non-electric detonators in the hermetical cylinder.

Dec 6, 2010

By J Elsen, R Snellings, K Van Balen

This research concerns the mineralogical study of the physico-chemical reactions taking place at the pozzolan-binder interface. Lime binder/ pozzolan mixtures have been prepared for different natural zeolites. Analcime, phillipsite, chabazite, erionite, mordenite and clinoptilolite were mixed with portlandite and water, after which the progress in the reaction was quantitatively determined by thermogravimetrical analyses from three to 180 days. A first and important step was the thorough characterisation of the raw materials by quantitative X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscope energy- dispersive X-ray (SEM-EDX) measurements of the zeolite minerals, Brunauer-Emmet-Teller (BET) specific surface area measurements, grain-size analyses and cation exchange capacity measurements. Beside these zeolite samples with varying Si/Al ratios, two clinoptilolite samples exchanged to the calcium, potassium and sodium form were studied and the difference in their short- and long-term reactivity was assessed. Also the difference in reactivity between identical clinoptilolite samples ground to different grain sizes, obviously having different specific surface areas, was determined experimentally. The results indicate that the external surface area only influences the short-term reactivity, whereas the cation content has effect on both long- and short-term. Na-exchanged samples combine clearly more portlandite in the first few days, whereas the reaction slows down afterwards compared to K- and Ca-exchanged samples. The early reactivity of the unexchanged zeolite samples could be explained by these two parameters, but their long-term reactivity seemed to be related to their Si/Al ratio. Samples with zeolites rich in Si reacted faster then their Al-rich counterparts.

Jan 1, 2008

By C Barton, B Randall, T Weldon, M Lefler

FLSmidth-Summit Valley Technologies has been a leader in gold processing equipment for nearly two decades. Over the past several years an extensive research and development effort has led to improvements in Mercury Abatement systems and process efficiency in Adsorption Desorption and Regeneration (ADR) or "Carbon" plant operations. Two technologies will be discussed that are focused on efficiency improvements followed by an explanation of Mercury Abatement systems. Gold and silver can be desorbed from carbon in several ways. FLSmidth has made significant improvements to the Pressure ZADRA process allowing for lower energy consumption and lower capital costs. This patented process is known as the Split-ZADRA Strip method. Split-ZADRA allows a plant to elute loaded carbon in a semi-continuous fashion. This increases the grade of the Pregnant Strip Solution, improves electrowinning efficiency, reduces capital equipment costs, and reduces energy requirements. During desorption and electrowinning for the Pressure ZADRA process, the pressure and temperature of the circulating strip solution is changed multiple times. A self-contained heating and cooling system has been developed which decreases the energy requirements for elution. Mercury Abatement technology has become increasingly important in recent years. Along with FLSmidth Summit Valley Technologies' complete Mercury Retorting Systems, FLS-SVT has developed systems for the capture and removal of mercury from electrowinning cell and strip solution exhaust, Carbon Regeneration exhaust, and the dore furnace exhaust. This paper describes each of the technologies introduced above and their success in operational gold and silver mines. Case studies will be discussed showing the advantages of each specific technology as it applies to operations around the world. CITATION:Lefler, M, Weldon, T, Barton, C and Randall, B, 2013. Improvements in the mercury abatement and process efficiency of adsorption, desorption and regeneration gold processing operations, in Proceedings MetPlant 2013 , pp 468-478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By B Powell

Coastal acid sulfate soils (ASS) are wetland soils and unconsolidated sediments that contain iron sulfides which, when exposed to atmospheric oxygen in the presence of water, form sulfuric acid. ASS form in protected low energy environments such as barrier estuaries and coastal lakes and commonly occur in low lying coastal lands as Holocene marine muds and sands. When disturbed, the iron sulfides in these soils can oxidise and produce large volumes of sulfuric acid (essentially similar chemistry to acid rock drainage with mines) resulting in the subsequent release of toxic levels of iron, aluminium, manganese and possibly heavy metals. This results in detrimental effects on aquatic biota, plants, animals and steel/concrete structures and on human health in the surrounding environment. There are an estimated 2.3 million ha of ASS located along 6500 km of the Queensland coastline. In contrast to many mineral sulfides encountered in the mining industry, the pyrite crystals in ASS can be as small as 2 mm and commonly occur as framboids with extremely large surface area per unit mass, substantially increasing their reactivity if exposed to air (oxidation). Highly reactive iron monosulfides can also occur, particularly in drains and shallow lakes. Many coastal areas, where some 80 per cent of the population of Queensland reside, are coming under pressure for agricultural and urban development. Construction of canal estates, marinas, housing/industrial estates, roads, golf courses, aquaculture ponds, sand/gravel extraction and drainage for sugar cane can disturb ASS and release sulfuric acid, which may then drain into adjacent waterways with heavy rain. As development continues to encroach on coastal lowlands, the identification, quantification and management of ASS must be addressed as part of a commitment to the principles of Ecologically Sustainable Development (ESD). ASS can be successfully managed by adopting best practices and following guidelines, but government, community and industry must collaborate to raise awareness, avoid æhot spotsÆ and develop more cost-effective solutions. Scientists led the education and public awareness program showing infrastructure and environmental damages arising from ASS in Queensland. Using results from mapping and research, they convinced policy makers, industry and polititians to accept the need for legislation founded on good science. The resulting æState Planning Policy 2/02: Planning and Managing Development Involving Acid Sulfate SoilsÆ identifies the StateÆs interest in acid sulfate soils. The Queensland Government considers that development involving acid sulfate soils in low-lying coastal areas should be planned and managed to avoid potential adverse effects on the natural and built environment (including infrastructure) and human health. SPP 2/02 states where the policy applies and when a development application will trigger the policy. It can also be used to assist local governments in preparing their planning schemes under the æIntegrated Planning Act 1997Æ. The SPP 2/02 comes with a æState Planning Policy 2/02 GuidelineÆ to provide advice and technical information on interpreting and implementing the SPP 2/02. This guideline has legal status in assisting in the interpretation of SPP 2/02. Those seeking more detailed technical information can now also access the æSoil Management GuidelinesÆ and ASS æSampling GuidelineÆ, available from the Department of Natural Resources and Mines website. These are some of a series of chapters being developed for the æQueensland Acid Sulfate Soil Technical ManualÆ.

Jan 1, 2003

By Larkin F, Farrer E, McGhie R. R

The Electrolytic Zinc Company of Australasia Limited commenced productive operations during February, 1936, at the- Rosebery and Hercules mines, which are situated near Rosebery, Tasmania. At this time it was decided that before re-organizing the steel sharpening shop a test should be made of the relative merits of conventional drill-steel and detachable bits. For this purpose Ingersoll-Rand type"I" thread centre hole.jackbits were selected and seventy-two of these were tested against conventional steel. Results indicated that, under the conditions pertaining at these mines, j ackbits should prove more economical than conventional drill-steel bits, and that a large-scale test, under working conditions, should be made. This was done by gradually replacing conventional drill-steel with jackbits at the Rosebery mine. Results were satisfactory and by the end of 1936 both mines were using only the jackbits.

Jan 1, 1939

The epithermal Au-Ag deposits of the Hauraki Goldfield have formed in the convergent plate margin setting of the Coromandel Volcanic Zone (CVZ). The deposits form as siliceous lodes in the upper parts of geothermal systems associated with andesitic and rhyolitic volcanism. Two types of low sulphidation epithermal mineralisation are recognised in these volcanic terranes. Vein deposits within the rhyolitic terrane in the east and south of the CVZ (Whitianga Province) are typified by Chalcedonic Silica-Adularia-Illite type mineralisation. The veins are hosted by both rhyolite-dacite volcanic rocks and the underlying andesitic basement. The mineralisation formed by episodic violent decompressional boiling of deeply circulating meteoric water, with some magmatic fluid contribution; this boiling was associated with hydraulic fracturing and hydrothermal eruptions in geothermal systems where the piezometric surface of the deep geothermal reservoir lay near-surface. Such episodic boiling provides chalcedonic veining, banding and brecciation textures, adularia stability, bladed calcite, and extreme loss of H2S gas from the fluid to cause major gold deposition.   Crystalline Quartz-Illite-(Adularia-Kaolinite) type mineralisation is widespread in the andesitic terrane forming the northern and western portions of the CVZ (Kuaotunu Province). There is a spatial association with weak mineralisation of the high sulphidation (Vuggy Silica-Alunite-Kaolinite-Illite) epithermal type and porphyry eu-Au type. Crystalline Quartz mineralisation is probably formed by the mixing of shallow acidic groundwaters with the ascending deep geothermal fluid in geothermal systems beneath andesitic stratovolcanoes. The piezometric surface to the deep geothermal reservoir in these systems is likely to lie at considerable depth, with acidic gases rising from the geothermal reservoir condensing within the overlying vadose zone. The cooling effect, oxidation and pH decrease accompanying mixing apparently overcomes the dilution effect, and results in quartz deposition, illite (and locally kaolinite) alteration, and precipitation of gold. A high level of base-metal sulphide precipitation also enhances gold deposition. Violent boiling of the mixing fluids may occur at local structural dilation sites, producing high grade "bonanza" gold mineralisation.

Jan 1, 1991