Search Documents

Two small coral islands in the Pacific Ocean, situated close under the equator, and formerly classed among the Line Islands, have, during the last three or four years risen into prominence owing to the valuable deposits of phosphate of lime discovered on them.The deposits of Ocean and Pleasant Islands are under the control of the Pacific Islands Company (1902) Limited, of London and, Sydney, and the high grade of the phosphate, together with the exceptionally favourable facilities for mining this mineral, of which there are several millions of tons on these islands, give this company advantages which enable them to command the Australian and New Zealand markets, and also to make large contracts with Japan and other countries. Both islands, as far as surface indications are concerned, are entirely constructed of coral, with phosphate on the top from the highest points to the present sea level, there being no sign of volcanic rocks, with the exception of a few pieces of drift pumice on the coast.Banaba (Paanopa according to. the Admiralty charts), also known as Ocean Island, was discovered in 1804. It is situated in lat. 0° 52" S. and long. 169P 3[)" E.

Jan 1, 1904

By E Hernandez, I Agustian, W Kusumohastuti

PT Freeport Indonesia is completing the first underground gyratory crusher excavation at their Deep Mill Level Zone (DMLZ) mine located in the mountains of Jayawijaya, District of West Papua, Indonesia. DMLZ is an underground block cave mine with an expected output of 80 000?t/d and a scheduled production start in 2015.In order to deliver crushed ore to the mill through the existing conveyor belt, the DMLZ block cave mine will construct two 1000?kW 1.6?×?2.3?m gyratory crushers with their own respective ore flow conveying systems underground. Each crusher is composed of top, middle, and bottom chambers with an ore bin. This system includes a series of high capacity conveyors approximately 5 km in length including transfer stations and support facilities.The development methodology required a combination of lateral development by jumbo drilling machines and vertical development by mechanised raise climbers (MRC) due to the complexity of the chamber design.This paper will discuss the project scope, design and development methodology, ground conditions, innovative survey controls, and the challenges faced due to the remote location.CITATION:Hernandez, E, Kusumohastuti, W and Agustian, I, 2014. Excavating the first underground Gyratory Crusher at the Deep Mill Level Zone mine, PT Freeport Indonesia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 43–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J Allen, B Oats, S Palaniandy, M Lollback

The Julius Kruttschnitt Mineral Research Centre has conducted an intensive VertiMill® (VTM) survey program at the Cannington mine concentrator as part of the ‘collaborative research in stirred milling technology’ program funded by Metso Minerals. Since 2003, Cannington has progressively added grinding capacity into the circuit through VTMs operating in secondary and regrinding duties. Cannington was one of the first mines to adopt this technology in secondary duty by installing two VTM-1500-WBs as part of a capacity expansion to produce sub-100 µm rougher feed. Subsequently, an additional VTM-800-WB was installed in the lead regrind circuit to prepare sub-20 µm cleaner stage feed.Several surveys were carried out to evaluate the VTM performance over a range of changed conditions. Among the key changes in operating variables were circuit power draw, feed rate and water addition to the bottom of the mill. The average specific energy for secondary duty was 3.7?kWh/t. The lead and zinc regrind mills consume 8.1 and 15.3 kWh/t respectively. Generally, the VTM installations have successfully prepared feed for rougher and cleaner circuits by reducing the top size into the floatable regime with steeper particle size distribution, which has led to enhanced recovery. The survey results show the success of VTM installations in secondary (receiving feed from autogenous circuit) and regrind duties.CITATION:Palaniandy, S, Powell, M S, Hilden, M, Allen, J, Kermanshahi, K, Oats, B and Lollback, M, 2014. VertiMill® performance updates in secondary and regrind duties at Cannington mine, BHP Billiton, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 263–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Seshold P

The cost of capital is the rate at which a project's cash flow should be discounted to obtain the Net Present Value. The cost of capital is a weighted average of both debt and equity funds of a company, on an after tax basis. Two methods are described for calculating a company's cost of equity, the Dividend Valu- ation Model and, more importantly, the Capital Asset Pricing Model. A worked example is presented where the cost of capital was obtain- ed for two resource companies. The application of the cost of capital was illustrated by way of a mining equipment replacement problem. The paper outlines refinements and problems that may be encountered with the use of the cost of capital, and concludes that it is an integral part of any project evaluation.

Jan 1, 1983

By S Hapugoda, M Kilburn, M Adam, L Lu

Lump ore is one of the key ferrous materials used in the blast furnace ironmaking process, typically accounting for 5–25 per cent of the blast furnace ferrous burden. Like other ferrous materials, the characteristics of lump ore have an important impact on stable operation and productivity of a blast furnace. As the cold burden lands on the top of the hot burden in the furnace and descends, it is inevitably subjected to thermal shock, which will likely lead to breakdown of the lump particles, or decrepitation and affect the gas permeability inside the blast furnace adversely. An ISO decrepitation test has therefore been developed to assess this behaviour of lump ore. However, the results obtained according to the existing standard decrepitation test method vary considerably between laboratories even for the same lump ore. To improve the test procedure of the existing decrepitation test, this paper first discusses the mechanisms leading to decrepitation and then studies the factors affecting lump ore decrepitation. Understanding the key factors affecting lump ore decrepitation is particularly important to improve the existing test procedure that enables researchers to achieve a higher degree of precision when conducting the decrepitation test.CITATION:Lu, L, Adam, M, Hapugoda, S and Kilburn. M, 2017. Decrepitation of lump iron ores, in Proceedings Iron Ore 2017, pp 91–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R Hao

Uncertainties in large open pit geotechnical modelling has been a major concern for slope stability analysis. The level of confidence in the in-put assumptions, such as structural and rock mass model, dictates the modelling results to some extent. This article is to detail a case study of Kalgoorlie Consolidated Gold Mines (KCGM) regarding a predicted inter-ramp failure on an as-built pit walls by a 3D numerical modelling. Significant concerns were raised across site and multiple preventive plans were considered. After intense data collection work, it was confirmed that the risk of failure had been overestimated. The case study has improved the understanding of geotechnical data in-put and has enhanced the process of creating and updating geotechnical structural models at KCGM.

Jun 22, 2022

By Lamont G

The significance of blasthole stemming in determining blasting efficiency has been extensively studied for small diameter holes using gelignite explosives. Recent developments in blasting technology with the use of large diameter holes and low cost blasting agents have not included studies of the effectiveness of different types of stemming materials. A review of previous measurement techniques and the relevance of these earlier results to present stemming practice is presented in this paper. A survey of operating mines in Australia provided information for this analysis. The value of stemming in reducing blast noise and improving blasting efficiency is generally accepted but the use of bulk-loaded explosives in underground operations has resulted in the practice of eliminating the use of stemming material.In surface operations drill cuttings are used for stemming on the basis of availability rather than efficiency in providing resistance to movement. The development of laboratory testing techniques, based on noise level and borehole pressure measurements, to evaluate the relative efficiency of different types of stemming materials is described. The results of an extensive series of tests with ANFO explosive showed similar trends tothose obtained from earlier published results with gelignite type explosives. Conclusive quantitative results on the relative effectiveness of different stemming materials will require minor modifications to the existingequipment. Observations and the results of pressure measurements indicated the presence of shock wave effects which caused the ejection of the top section of the stemming column when using coarsely fragmented material.

Jan 1, 1979

A predicted increase in aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Browncoal char, with a lower ash content and with an elemental purity similar to petroleum coke, was produced by leaching in hydrochloric acid, washing with water, and charring at 1,150°C. The cost of processing is estimated tobe competitive with petroleum coke.Without further processing the bulk density and real density were undesirably low, but by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value andthe particle density was improved to 92 per cent of the density of petroleum coke by water displacement or 75 per cent by mercury displacement.Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char, and from petroleum coke alone, all bonded with coal tar pitch.The electrodes were tested for the usual physical properties and were evaluated for performance in a laboratory size alumina reduction cell.Electrodes based on brown coal char alone were found to be inferior in physical properties and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity, and carbon consumptionon a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 per cent better electrical current efficiency than the electrodes based on petroleum,coke alone.It is suggested that larger scale tests are warranted.

Jan 1, 1971

The Tertiary gold deposits of the Hauraki area are predominantly epithermal vein types containing mineral assemblages of quartz, calcite, pyrite, sphalerite, galena, chalcopyrite, acanthite and native gold (electrum). Sulphosalt, telluride (eg hessite), seleniferous sulphide and selenide minerals are important locally. Studies of wall rock alteration mineralogy, fluid inclusions in gangue minerals, and sulphur isotopes of sulphide minerals indicate that the ore forming fluids had the following parameters: pH, near neutral at depth but acidic near surface; temperature, predominantly 320 - 270¦C for base metal dominated assemblages, 280 - 200¦C for precious metal dominated assemblages and generally below 200¦C for late stage barite; apparent salinity, six to zero equivalent weight per cent NaCl; and CO2 concentration, generally around one mole per cent CO2. There is fluid inclusion evidence for boiling during mineralisation in some deposits. Moderate values off S2 and FO2 are indicated for base metal and mixed base metal û precious metal assemblages of most deposits by the predominance of pyrite + chalcopyrite over other iron-bearing phases; primary bornite is absent, whereas pyrrhotite, hematite and magnetite rarely occur in the veins. The largest gold û silver deposits formed from solutions in which the sulphur species in solution were predominantly reduced. Near surface environments and some deep, predominantly base metal, deposits were formed from solutions with approximately equal concentrations of oxidised and reduced sulphur species.

Jan 1, 1984

Effect of Grinding Media on the Flotation of Sulfide Minerals

Sep 13, 2010

By J D. Grobler

In the heavy minerals industry wet high intensity magnetic separators (WHIMS) are widely applied for primary magnetic separation of magnetic minerals and non-magnetic minerals. This piece of equipment is well known for its robustness to handle a wide range of feed conditions and still produce stable product qualities and yields. A heavy mineral production plant aimed to increase production through their WHIMS plant containing 11 duties and 26 units. Instead of adding new units an alternative approach was followed to firstly maximise the efficiency of the current circuit and secondly to consider possible reconfiguration of the circuit to produce additional product tons for minimal capital investment. In order to characterise the current circuit’s efficiency, identify pockets of excellence and determine the areas for improvement the whole circuit was surveyed several times and mineral mass balances were drawn up.This paper aims to: discuss the modelling process of the WHIMS circuit,explain the calibration and validation process followed to ensure the accuracy, anddemonstrate the sensitivity analysis performed on the different options. From this analysis an efficiency criteria was developed to compare different circuit configurations that enabled the production plant personnel to make an informed decision on the way forward.

Oct 5, 2011

By R Wedmaier

Henty Gold Mine is an underground operation producing 100 000 ounces of gold per annum. The original mining method used was flatbacking with paste fill. However, a non-entry method û uphole benching û was introduced in 1998 to recover the deteriorating crown pillars. Initial challenges were encountered, including poor drilling accuracy, difficulty in charging holes and poor rise performance. These challenges were overcome by a Continuous Improvement Team, consisting of mining engineers, supervisors and miners. Following this, the Team implemented further changes aimed at reducing ore loss and dilution. A second area addressed by the Team was development blasting, where innovative detonator technology known as the ExelTM DevelDetTM was introduced and rapidly accepted by the operators. Continued use of the ExelTM DevelDetTM resulted in a number of benefits, such as easier bogging, less perimeter damage, faster charging and hook-up and decreased wastage. Finally, improvements were made in the area of explosive handling, where competency-based training of operators was conducted and manual handling of ANFO has been significantly reduced by the introduction of the MiniMoverTM into the underground magazine.

Jan 1, 2001

By Burns W. G, Muceniekas E, Whitcher I. G, Hughes F. E

No iron ore deposits were reported before 1961 from the Hamersley Ranges, Western Australia, although low-grade bedded iron formations, associated with ferruginous jaspers and cherts, were known to occur in the local Nullagine Series of Precambrian age.In January-March 1961 preliminary investigations in the area drained by the Turner River, Duck Creek and Serpentine Creek revealed the presence of over 1000 million tons of dense botryoidal or pisolitic limonite, forming flat-lying orebodies with 50-57 per cent iron.Large bedded hematitic orebodies were also discovered in the same area in August-October 1961. These have a porous, biscuity texture and an iron content of 60-61 per cent. They occur at a welldefined stratigraphic level (Brockman Iron Formation), normally in synclines where they have been upgraded by circulating meteoric waters during an old cycle erosion.In 1962 systematic geological studies and mapping, together with sampling and scout drilling, indicated larger reserves of biscuity hematitic ore and led to the discovery of massive hematite deposits at Mt. Tom Price. These were extensively drilled in 1963, proving the persistence of' high-grade mineralisation to a depth of 200 ft and over.To date the total indicated reserves of the Hamersley deposits, within the area held by Hamersley Iron Pty. Limited, are of the order of 4960 million tons and thus rank among the more important of the world. The reserves are composed of 600 million tons of bedded dense hematite ore with 64-66 per cent iron, 2900 million tons of bedded biscuity hematite-limonite with 60-61 per cent iron, 1360 million tons of limonite (goethite) ranging in grade from 50 to 57 per cent, and 100 million tons of canga (conglomerate) iron ore containing 53-63 per cent iron. In all cases harmful impurities are comparatively low.

Jan 1, 1964

By Bothe C

Froth flotation processes use different surface properties of the minerals to be sorted. In an aqueous environment the hydrophobic mineral attaches selectively to air bubbles and is lifted to the surface of a separation vessel, while the tailings settle towards its bottom. Besides the surface properties, the hydrodynamic conditions play an important role. With respect to the hydrodynamics the flotation process can be divided, for simplicity, in two sub-processes. The attachment of hydrophobic particles to air bubbles, the so-called mineralisation, demands a large number of collisions and therefore high turbulences. The phase separation however needs a deterministic movement of both the particle-bubbles-aggregates and the tailings particles and therefore a quiescent flow field. The optimisation of the overall process requires a separation of both sub-processes, especially when fine particles have to be sorted. In conventional mechanically agitated flotation cells both sub-processes take place in the same turbulent volume. For this reason they suffer from a decreasing selectivity with decreasing particle size. In flotation columns the mineralisation of air bubbles and the phase separation are performed in a quiescent environment. This results in high concentrate grades and at the same time in a very slow attachment kinetics, which must, especially for fine particles, be counterbalanced by a long residence time of the slurry.

Jan 1, 1993

By Yates C, Gillie E. W, Finucane K. J

During the year 1940 a complete investigation was made of the whole of the stoping operations throughout the Great Boulder Mine and, as a result, it was decided to convert some of the existing shrinkage stopes into cut-and-fill stopes, and also to mine many of the more recently developed ore blocks by the latter method. The necessity for filling was due primarily to the structure of the ore blocks, the character of the walls and possible excessive dilution, but was influenced also by the grade of the ore-block and by the fact that cleaner mining can be carried out by cut-and-fill stoping.The comparatively few cut-and-fill stopes in operation prior to 1940 had been filled mainly with waste rock from development work, but as the amount of this material available, or likely to become available, would have been wholly inadequate for future operations, it was proposed to construct a system of passes to supply filling material from the surface.Owing to the distribution of the stopes, no central pass or system of passes could be devised which would service all the stopes satisfactorily.However, work was commenced on two passes, one designed to service the cut-and-fill stopes in the Eastern Section of the mine, and another to service those in the Western Section. It was realised that these passes could serve only a small proportion of the total number of Stopes (Figs. 1 and 2). During the progress of this work experiments were undertaken to test the possibility of using filtered tailings underground as an adjunct to the above scheme, but for various reasons these were only partially completed.Early in 1942 it was suggested by the Mill Superintendent that an attempt be made to fill with wet classified flotation tailings as practised at Mt. Lyell in Tasmania and at the Triton Mine at Reedy, West Australia. For the purpose of testing this, an experimental stope was prepared on the 309-ft. level, "X" Lode. This was 100 feet long and averaged 4 feet in width. Water-tight rearings were built at each end of the stope and waste rock fill was spread to a height of 6 to 8 feet above the timber. Used filter cloths were laid on top of the fill and brought a few feet, up the walls of the stope. A two-inch victaulic drainage line was then placed in position, the end passing through a hole in one of the bearings and thence to a sump. In the central portion of the stope two vertical pipes were brought up from this line. These were bored with one-inch holes staggered on opposite sides of the pipe, the vertical interval between each hole being one inch. The holes were then stopped with...

Jan 1, 1945

Over the last 20 years the mining industry has played a key role in the further development of many Central Queensland and New South Wales communities. The number of people who are employed by the coal mining industry, the number of transient residents, shift work and the town facilities have all contributed to how the community views the coal mining industry. As the coal mining boom continues and the mining communities continue to grow more emphasis is needed to address the community concerns, specifically the socio-economic and environmental impacts that the coal mining companies may have on these communities. Central Queensland coal mining operations are situated in the Bowen Basin. Many of the towns in the region have been developed specifically for the coal mining industry with 13 - 50 per cent (Australian Bureau of Statistics, 2006) of people living in the communities being directly employed by the mines. The introduction of shift work, differing rosters and the mining boom have resulted in considerable changes to these communities with more transient contractors and permanent employees taking up residence outside of these communities. This change, however, has not been as noticeable in the Hunter Valley region. The Hunter Valley, situated in the Sydney Basin has two main mining towns, Singleton and Muswellbrook. Of the 37 173 (Australian Bureau of Statistics, 2006) people that reside in the communities 13.8 to 16.5 per cent (Australian Bureau of Statistics, 2006) are employed directly by the mines. The Hunter Valley is a large tourist destination due to its many vineyards; this results in a diverse community where mining is not the sole means of employment. Similar to Central Queensland the mining boom has brought more people to the Hunter Valley region, although greater percentages have taken up residence in the communities. The views vary between the two regions on the coal mining industry, specifically on the socio-economic and environmental impacts that the industry may have on the surrounding communities.

Jan 1, 2008

In 1980 Pancontinental Mining Limited decided that while the Jabiluka uranium project was still a major focus of the company's efforts some diversification was necessary. At this time it was decided to include precious metals in Pancon's exploration and acquisition objectives. As a result the now Paddington Gold tenements were acquired, explored and developed. Today, it rates as the 6th largest gold mine in Australia and at an expanded throughput of 1.2 million tonnes per year of ore it will produce about 110,000 ozs of gold per year. Following extensive exploration activities by Pancon's Exploration Division the Operations Division continued with development drilling finally proving up a reserve of about 8.4 million tonnes at an average grade of 3.2 g/t. An in- house preliminary feasibility study was followed by a two phase feasibility study by Davy McKee. This resulted in a recommendation to the Pancon Board of Directors to develop Paddington with an annual throughput capacity of 875,000 tonnes. This paper describes the acquisition, exploration and development of the Paddington project. It goes on to

Jan 1, 1986

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The Greymouth Coal field is situated on the West Coast of New Zealand's South Island and has been mined for coal for more than 120 years. The area covered in this paper is within the Rapahoe Sector of this field and contains >200 million tonnes of low ash, low sulphur, bituminous rank coal. Paper No 6, presented to the 19th Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy in Christchurch in August 1985 by R G Bowman, explained 'A Geologist's View' of the 'Economic Potential of the Greymouth Coalfield', and describes previous geological assessments of the Rapahoe Sector.

Jan 1, 1989

By Kissell F. N, Volkwein J. C

The U.S. Department of Interior's Bureau of Mines has the opportunity to visit many U.S. mines, including some that claim 2 to 5 times the national average of 334 raw tonnes/unit shift (tps) from a continuous miner section. In a project to assess the reasons for this high production, the Bureau conducted two studies. The first study focused on the 25 highest producing continuous miner sections. What stood out during the visits-was the quality of the labor-management relations. In each of the mines there was a positive labor/management relationship based on mutual trust and a sense that the employees were the company's most valuable resource. Discussions with labor revealed a universally positive attitude toward the company. Interviews with the mine superintendents invariably ranked the quality and attitude of workers as more important than anything else. Also during the mine visits of the 25- mine study, no engineering factors obviously stood out. Time at the face was greater than average, most were in coal over 1.52 m and the roof was generally good. Also, none of the 25 mines had to contend with high methane levels. Because this study found that a high percentage of mines were in seams less than 1.52 m thick, the second study examined thin seam mines only.

Jan 1, 1988