Search Documents

By P Vaikkattil, K Li, J Bullock

Unlocking maximum value is essential when designing a stope and the associated drill and blast packets. This is becoming increasingly important at Olympic Dam as the operation continues to expand south into the new mining areas away from existing infrastructure, increasing operating costs and required capital investment; into areas with less competent ground conditions, requiring smaller stopes and increased interactions. The introduction of Orica’s WebGenTM system is one way in which Olympic Dam can continue to unlock value into the future by decoupling traditional drill and blast limitations. The Lime 390 stope was the first stope at Olympic Dam to trial the new technology on the last blast packet. This paper reviews the drill and blast design of the Lime 390 stope, including the technical and operational challenges associated with the stope and the trial of the Orica’s WebGenTM system for the firing of the last blast packet.

Mar 15, 2021

By R Battison, R Duggan, S Esen, K Henley, P Dare-Bryan

Increased catch bench crest loss has been observed in recent years at Barrick’s Cowal Gold Mine situated in central New South Wales, Australia. A project was initiated to diagnose the cause of the crest loss, and evaluate ways to limit its effect on final walls.A range of different blast measurement techniques were utilised to evaluate the progressive damage caused to catch berms by presplit, production and trim blasts. Techniques employed included; single point vibration measurement, cross-hole seismic analysis, precision berm surveys, horizontal p-wave velocity measurements, crest loss volume calculation and water level changes between blasts.Blast measurements showed that the majority of damage to the catch berm was caused by the presplit blasts, which registered vibrations greater than 700 mm/s at 5 m behind the presplit line. As a result, considerable changes were made to the blast designs after a series of computer simulations via mechanistic blast modelling (MBM). The uncharged presplit collar was increased from 2 m to 4 m, and every second hole was left uncharged. Vibration modelling using a multiple seed wave (MSW) model was used to optimise trim blast delay timing. Burden relief was changed from 16 ms/m to 27 ms/m using one hole firing per 4 ms time window, and the initiation angle was changed from shallow to steep. These changes in the presplit loading and trim timing helped reduce catch bench crest loss by 1–2 m.Trim shots using a high strength bulk emulsion explosive were also identified as contributors to berm damage after analysis of blast monitoring and MBM modelling. The modelling study resulted in the generation of alternative blast designs to minimise the crest loss, including the use of low-density/low-velocity of detonation (VOD) bulk explosive product (Flexigel™ Advantage) in trim pattern designs. This was trialled on the Northern and Eastern pit walls to evaluate the damage to catch berms on final walls. The trials demonstrated that berm vibration was reduced significantly; fragmentation was similar (or slightly blockier) compared to the fragmentation using the old blast designs; displacement of the berm was reduced, so increased catch bench widths were attained. This paper summarises the trials, and presents a summary of the crest loss to date.CITATION:Battison, R, Esen, S, Duggan, R, Henley, K and Dare-Bryan, P, 2015. Reducing crest loss at Barrick Cowal Gold Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 189–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Kepert

It is the role of the exploration geologist to create wealth through the discovery, delineation and characterisation of economic mineralisation. This requires a critical depth of geological understanding.Unfortunately, the resource industry is well known for its cyclic nature. Many of the current generation of workers have only ever experienced the boom of the ‘super-cycle’ and are only just discovering the negative side to the business. For the case of the geologist and especially the exploration geologist, the magnitude of peaks and troughs are usually amplified and may become destructive to all parties. During the uptime a healthy stream of exploration good news becomes the staple diet of company releases, in particular those of junior companies attempting to bolster the share price. The geological knowledge and experience gained thus forms a significant and integral part of the value and therefore, future of a company. On the downturn it is often viewed that geologists are a luxury, an optional extra and a burden on the bottom line with companies entering a period of memory loss and myopia.Retention of geological knowledge however remains critical as projects, companies and cycles mature. Beyond exploration per se, this knowledge becomes both fundamental in de-risking and commercialising an asset (through development or divestment) and in positioning the company for cyclic or counter-cyclic opportunities.The growth and retention of this knowledge base is difficult to quantify in terms of direct value but becomes one of a successful resource companies greatest assets. At worst, its loss can lead to millions of investors’ funds wasted on missed opportunities, drilling, or poorly designed plant and mine.But the rocks are around for the longer haul and pay little notice to the vagaries of the scurrying of Man.This paper reflects on some of the authors own observations through 25 years of iron ore exploration, in why it is critical to always rigorously question the prevailing geological (mis)understanding and the technical and commercial benefits which that may bring, and looks forward to the future.CITATION:Kepert, D, 2015. Geology – the affirmative case, in Proceedings Iron Ore 2015, pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G Jones

The Singapore Land Transport Authority (LTA) has been procuring the expansion of their underground mass rapid transit rail network at a prodigious rate since the first line opened in 1987. Four lines (149 km) are currently operating and several more lines are at various stages of planning/construction; one of these is the Downtown line stage 2 (DTL 2).DTL 2 contract C917 was awarded in September 2009 for S$320 M. On 18 June 2013 the original contractor became insolvent, leaving the works incomplete. Following a fast-tracked tender process, McConnell Dowell was awarded the S$254 M contract on 29 August 2013 to complete the works. This contract includes two underground stations constructed by cut-and-cover methods and twin bored tunnels between the stations. Each tunnel is 1400 m long, excavated by earth pressure balanced (EPB) tunnel boring machines (TBM) at an average depth of 20 m and segment lined to 5.8 m inner diameter. The tunnel alignment is located under a busy five-lane road lined with prime residential real estate and congested with utilities.To compound the difficulty the tunnels are located within the notorious Bukit Timah Granite formation. This has a very wide range of strength, from below 1 MPa to over 300 MPa. This strength range is a consequence of six weathering grades, from soil to fresh rock, with the fresh granite causing severe abrasion problems. The various grades can occur within a very short distance of each other. Consequently, the problem of supporting a mixed face exists, particularly in the intermediate weathering grades where intact rock is encountered in the invert and corestones within a loose soil matrix in the crown, which can increase the instability by allowing the ground to flow into the TBM.The focus of this paper will be the excavation of the bored tunnels by EPB TBM used by McConnell Dowell to complete these challenging works.CITATION:Jones, G and Shepherd, J, 2014. Earth pressure balanced tunnelling in a dense urban environment, C917A, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 41–50 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By S Harrison

Work health and safety duties around Australia include duties to manage psychosocial health and safety (mental health) of workers engaged by businesses or undertakings and of other persons impacted by the operations of the business or undertaking. Persons conducting a businesses or undertakings must develop systems of work and policies and procedures for ensuring, so far as is reasonably practicable, the safety and health of workers and other persons. Officers have a duty to exercise due diligence and to ensure effective systems are developed, implemented and resourced. The developed systems will only be effective with worker’s co-operation and engagement. The duties placed on workers by work health and safety laws are an important part of the safety matrix of obligations. Supervisors and Leaders are workers and they play a critical role in delivering health and safety outcomes. To deliver these health and safety outcomes with respect to psychosocial safety Supervisors and Leaders need to understand their obligations and have a framework to use to assist them in understanding what workers require and what steps need to be taken to meet their duties. They also need to take steps to assist those workers that they supervise to meet their duties.

Apr 16, 2024

By R Norris, M Dunne

Substantial efforts by the industry, as well as by process and equipment designers, have resulted in many innovative developments that provide cost effective reductions in water usage. This paper showcases four emerging best practices in industry including examples of recent installations. Belt press filters are a small fraction of the operating and capital cost of alternative ædryÆ tailings technologies. This gives operators who must ædryÆ their tailings a competitive advantage and makes such operations much more sustainable. The new generation of belt filter presses use less energy, produces lower cake moistures and better disposal stacking properties. The need for tailings storage facilities may be eliminated or in some cases high-grade tailings can be dewatered and sold as a low value product. Mining applications include sand tailings, sinter plant waste, coal tailings and power station fly ash. Flip-flow screening machines are proven worldwide in the dry classification of coal and other minerals, reducing the size of beneficiation plants, whilst reducing energy, water demand and media consumption. They also allow the screening of wet/sticky materials not able to be sized using conventional screens. Lamella separators are used for toxic water clarification and/or sludge thickening in many downstream metal industries with the underflow often dewatered in a belt filter press. Such low cost, high capacity thickeners could also be used instead of conventional thickeners at smaller mines. The simple and reliable continuous washing upward flow (CWUF) sand filters have been used for treatment of waste water from coal preparation plants and steel works as well as in the production of potable water. The filtered waste water from mining processes can then either be reused or discharged from site. Other installations include cleaning mine water to prevent the blocking of dust suppression spray nozzles.

Jan 1, 2006

By S Robinson, A Turner, R Dale, C Butler

"Sandfire Resources NL- (‘Sandfire’) DeGrussa definitive feasibility study (DFS) identified geometallurgy as a major factor in achieving optimum plant performance at the DeGrussa mine. A geometallurgical initiative was created to proactively investigate this issue, and a key initial achievement was the 2013 paper by Condon et al (2013) on developing a working geometallurgical model from first principles. Significant advancements in Sandfire’s geometallurgical understanding since that publication now shape how information is presented and communicated.The main geometallurgical parameters so far identified as critical factors affecting plant performance are Cu:S ratio, iron sulfide mineralogy, talc carbonate content and sphalerite content. Apart from specific mill strategies, geometallurgical issues have been managed through communication between departments and strategic run-of-mine (ROM) pad management.This paper uses the current theories of geological evolution of the volcanogenic massive sulfide (VMS) deposit at DeGrussa, to discuss the variability between the orebodies C1, DeGrussa (sea floor mounds) and C4, C5 (sub-sea floor replacement) to highlight the different issues each orebody is expected to encounter when processing.A zone of altered low-grade mineralisation surrounds the main orebodies at DeGrussa, referred to as a halo. Talc minerals are often patchy within this halo and often cause significant recovery issues during processing. This halo has been successfully modelled using MgO as a proxy. The ability to model the talc material assists with both identifying potentially problematic zones for processing and geological interpretation of the ore deposits evolution.Early in geometallurgy studies at DeGrussa it became apparent that it would be useful to identify processing performance prior to mining. This necessitated the incorporation of specific sulfide species into the mining block model. These attributes are interpolated from the logged sulfide estimates allowing a clear picture of the abundance of each mineral type within a defined area.In conjunction with the block model a geometallurgical factor (GMF) graph was developed, identifying sulfide mineralogy based upon mineral assays. These two recent additions to the model provide a clear picture of the nature of the ore sources that will be presented to the processing plant.The future of geometallurgy at DeGrussa will see these tools used to aid mine scheduling with a view to further improve processing recoveries.CITATION:Butler, C, Dale, R, Robinson, S and Turner, A, 2016. Geometallurgy – Bridging the Gap between Mine and Mill: a Case Study of the DeGrussa Geometallurgy Program, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Project-finance risk assessment is mature and approached systematically. Mining industry due diligence remains fragmented with specialists addressing different aspects of the project such as reserves/JORC, environmental impact, commodity market, even financial analysis/ modelling. Each professional has a natural tendency to believe that the risk factors they have examined are the key ones necessary to be reviewed, as if their review will stand in isolation from others in the way a project materialises. By first laying out the project risk categories and risk matrices, this paper examines the due diligence process with a keen eye to the risk assessment and overlap/interaction. Some cross fertilisation of due diligence techniques from other industry sectors is placed into the mining context. Six case studies are then presented with regards to due diligence features in each projectÆs feasibility review or financial information/ offering memorandum. A power case first shows the differences between the due diligence expectations of banks versus bond financings. Then some Australian and Indonesian mining development cases are analysed to see the due diligence learning points. Some of these were project/due diligence failures. The conclusion focuses on the value of a systematic risk assessment for project evaluation, all from the project-finance perspective.

Jan 1, 2007

By S A. McManus

With the advances in software speed and capability, many of us now are running multiple scenarios on entire models rather than just testing small areas or a few blocks. In the authors experience both the geological and geostatistical academic theory and our rules of thumb, often prove un-useable or incorrect in the real world we work in. The only way to truly validate and tune our models is to complete the entire model and ‘see if it works’. If it lacks some property we were expecting, then we need to find out why and/or run different scenarios to see what changes. This is not always possible with tight project timelines but we find ourselves doing more and more of this sort of thing, and in so doing, understand that every deposit is different and requires its own ‘rules’ to get valid and useful results. For the purposes of this paper, this process is termed Empirical Geostatistics. Take Clayton Deutsch’s ‘all realisations all of the time’ concept a step back. Before you even think of simulating, test the alternate realisations generated by alternate parameters such as different domaining, varying search neighbourhood parameters etc.

Mar 22, 2022

By D Giles, A C. Bailey

In the first 20 years of the 21st century, just over 20 per cent of Australian mineral exploration expenditure was dedicated to iron ore, totalling >A$8 billion and >30 million metres of drilling (Australian Bureau of Statistics, 2021). Improvements in the cost, efficiency, safety, reliability and data quality of drilling have the potential to deliver significant productivity improvements, increasing the probability of discovery and reducing the time from discovery to mining. Currently in its third year of research, Mineral Exploration Cooperative Research Centre (MinEx CRC) is focused on a new set of exploration tools and new ways to deploy those tools which recognise the fundamental importance of collecting quantity and quality data from the subsurface, to enable exploration success for all minerals, including iron ore. MinEx CRC is focused on developing more productive, safer and environmentally friendly drilling methods to discover and drill-out deposits. This includes pioneering work on Coil Tube (CT) drilling technology and innovations in Diamond and Reverse Circulation (RC) drilling techniques aimed at improved drilling optimisation and automation. In parallel, MinEx is developing new technologies for collecting data whilst drilling. This is being undertaken in four separate industry-led projects utilising geophysical, seismic, downhole analytical and 3-dimensional (3D) modelling improvements. A National Drilling Initiative (NDI) is also underway, with two drilling programs completed in 2020. The NDI is a world-first collaboration of Geological Surveys, researchers and industry, which undertakes drilling in under-explored areas of potential mineral wealth in Australia and provides a test-bed for new mineral exploration technologies.

Nov 8, 2021

By T Purvis

Xstrata Copper is extending the Ernest Henry Mine with a 6 Mtpa sub-level cave (SLC) mine being constructed under the pit. The SLC mine will maintain the EHM operation until 2024 after the pit is completed in August 2011. In February 2008, the first cut of the new underground mine at EHM was fired with the start of an exploration decline. Since then Xstrata Copper has continued the development and construction of a SLC mine. During this process a number of challenges arose, some of which had not been anticipated in the planning stages, that in turn has been addressed to ensure the development continued. The challenges have been many and varied and range from setting up the portal area and commencing the exploration decline development in an active large open pit, to management of underground water. Further challenges were presented by the effects of the GFC on investment recommendations, with the scale of the mine varying from a shaft mine to a smaller scale trucking only mine in mid-2009 and back to the full shaft mine in late 2009. The effect was the parallel development of two separate mining scenarios, with the challenge of maintaining commonality for as long as possible to keep both options alive until the final board approval was obtained. In 2010 the RSPT caused further impacts. This paper will describe the current progress of mine development as well as how the various challenges have been met and some key lessons learnt from these experiences.

Mar 21, 2011

By S T. L Harrison, J-P Franzidis, M Becker, N Dyantyi, J L. Broadhurst

Gold mining is a major contributor to the South African economy, but is associated with several environmental issues such as acid rock drainage (ARD). ARD is due to the oxidation of sulfides in gold tailings and is characterised by low pH, high sulfate content and elevated concentrations of heavy metals that contaminates scarce water resources and subsequently limits the use of such waters without treatment. Treatment strategies can only be implemented if the acid-generating potential of mine wastes is effectively predicted using common static and kinetic acid prediction tests. The choice of test performed is usually a trade-off between the number of samples, speed of the test, cost of the analysis and level of information obtained. Often the results of these various tests are not consistent with one another. This study uses mineralogy to analyse biokinetic test results of a Witwatersrand gold sample in order to improve the understanding of behaviour of mine wastes under different ARD prediction test conditions.All ARD prediction testing methods investigated in this study showed that the gold sample is considered to be potentially acid forming with net acid generation (NAG) pH of 2.5 and net acid producing potential (NAPP) of 36 kg H2SO4/t. Results of biokinetic test showed that ANC was consumed within four days confirming acid producing potential of the sample with low neutralising potential as observed from acid base accounting (ABA) (4.7 kg H2SO4/t) and mineralogy (4.9 kg H2SO4/t). Results generated in this study demonstrated importance of mineralogy in both understanding the controlling reaction mechanisms playing key role in ARD formation and its capability as a prediction technique. Future work will focus on the application of mineralogy in interpreting the behaviour of mine waste under different static test conditions with a view to assessing their applicability and reliability in estimating potential acid generating characteristics of gold tailings.CITATION:Dyantyi, N, Becker, M, Broadhurst, J L, Harrison, S T L and Franzidis, J-P, 2013. Use of mineralogy to interpret laboratory-scale acid rock drainage prediction tests - a gold case study, in Proceedings World Gold 2013, pp 519-526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A J. Gunson

The Norman B Keevil Institute of Mining Engineering, or the Department of Mining Engineering (the Department), at CanadaÆs University of British Columbia (UBC) is addressing the integration of sustainable development concepts into mining education and research on behalf of industry and society. Over the past decade, the DepartmentÆs education and research model has been evolving to incorporate collaborative and multidisciplinary strategies, where sustainability initiatives are taught in classes, supported in research and discussed in a voluntary collective of mostly graduate students û the Sustainability Working Group (SWG). The SWG has brought together a diverse array of disciplines from academia, industry, government, non-governmental organisations (NGOs) and mining communities. The operational mechanisms and structure of the SWG have enabled momentum to be gained through several multidisciplinary educational and research networking initiatives. It acts to attract new students with diverse backgrounds, foster innovative research, develop relationships and networks, and create the space to discuss progressive ideas and projects. The original cohort of SWG graduate students laid the foundation for sustainable research initiatives within the Department at UBC. Novel research has incorporated topics such as: community resilience, artisanal small-scale mining, sustainability indicators and corporate social responsibility, environmental assessment and impact benefit agreements and the recycling of waste. Propelled by the support of the Department and inspired by the works completed, a host of new graduate students have embarked on their research quests to integrate sustainability principles into their projects. Such projects include: social impacts and benefits of mining, artisanal small-scale mining, community health, the production and transport of mine pollutants, mine waste management, mineral process plant design and the evolution of community education and mine policy. This paper reports on the departmentÆs continuing research and development towards an understanding and evaluations of the ongoing contributions of mining to sustainable development.

Jan 1, 2009

By I Minniakhmetov, J Ashford

Orebodies constitute naturally occurring, commonly highly variable concentrations of minerals in the earth’s crust formed through varying and highly unpredictable processes. Orebody knowledge is a core foundation of a mining company’s asset base underpinning all decisions about Mineral Resource and Ore Reserves, future production, development and ultimately the profitability and competitiveness of a mining enterprise. The decision to invest in a mineral project is usually based upon a techno-economic evaluation of the project and having clear approval pathways to gain local community support and address social and environmental impacts. The main objective of the techno-economic evaluation is to determine the optimum development sequence for the particular orebody in question and to estimate the economic viability of the project and the future return on investment to its stakeholders, balancing the inherent value of the mineral in the ground against the costs of development and market pricing. With the exception of market-driven commodity prices, virtually all revenue and cost estimates fundamentally stem from the understanding and subsequent modelling of the orebody. A reliable estimate of the ore deposit grade and other geological value-drivers is the foundation upon which the business case for future mine development and operation is intricately dependent. Orebody knowledge is, therefore, the fundamental driver of the mineral project cycle, influencing the progression of studies and consequently, the resource company’s ability to declare Exploration Results, Mineral Resources or Ore Reserves which govern the source and cost of funding available to the project. Drilling provides a ‘vector’ to the true nature of the orebody and effectively buys time to manage the technical risk associated with the orebody. Despite its perceived high cost, in both time and money terms, drilling is the only available technology for acquiring the necessary orebody knowledge to support technical and economic studies and to minimise orebody-driven cash flow uncertainty and volatility. However, like all costs, pressure to minimise drilling budgets is ubiquitous across the minerals industry. Paired with inappropriate key performance indicators, drilling is often regarded as a cost to be minimised, rather than an investment to be optimised. Furthermore, as future deposits get deeper and more complex, the collection of orebody knowledge is increasingly on the critical path for project development. The increasing cost of data collection pertaining to these deposits increases the temptation to minimise orebody knowledge gathering at the cost of long-term value as the reduction or postponement of drilling results in greater orebody knowledge risk at all stages of the value chain. Indeed the true cost of the decision to drill less is rarely known until the mine is in operation, well after the mine project evaluation team has moved on. This paper aims to promote orebody knowledge as the fundamental source of endogenous project financial risk and, consequently, its critical importance in project financial evaluation. Furthermore, the report documents experimental research into the development of an econometric model for valuing orebody knowledge. Using the density of drilling data as a proxy measure of orebody knowledge, the proposed approach integrates well-established stochastic grade modelling techniques with the mathematical mechanics of Decoupled Net Present Value (DNPV) which, combined with stochastic grade modelling (conditional simulation), lends itself to the financial International Mining Geology Conference 2022 | Brisbane, Australia and Online | 22–23 March 2022 3 assessment of orebody knowledge risk. Based on this approach, a metric is formulated, representing the minimum value of the orebody knowledge added by additional drilling

Mar 22, 2022

By P Hanna

Following the Busang fiasco, more detailed guidelines were appended to the latest revision of the JORC Code released in September 1999 (JORC, 1999). Although the definitions and terminology essentially remained unchanged, the additional information in the guidelines has highlighted a number of issues for consideration by geologists undertaking computer-based resource estimations. The three main issues are:Data Integrity û details such as drilling and logging techniques, sampling procedures, assay tests, site visits, data recording and aggregation methods need to be considered. Geological Interpretation û is the Competent Person applying the appropriate software interpretation to the deposit in accordance with the regional setting. Are the correct computer-based tools being applied and are they producing the desired result (without compromise) to the satisfaction of the Competent Person? Modelling Technique û the importance of the relevant experience of the Competent Person not only in regard to the geology, but also with respect to the modelling algorithms and resource calculation methods of the computer software system involved. At the end of the day, it is essential that the Competent Person undertake a reality check on the resource estimation itself. They should also check that the borehole spacing is in accordance with the level of continuity for each critical parameter (such as structure, grade, impurities, etc) for which the resources are categorised.

Jan 1, 2000

By H Utama, hi, A Suw

PT. Indo Muro Kencana (PT.IMK) is gold and silver mine located in Central Kalimantan province, Indonesia. Mining activities in PT.IMK is conducted in Bantian pit area by applying surface mining method and using combination of excavator and hauler (articulated dump truck and rigid haul truck) as the transportation for ore to the crushing plant and waste material to the waste dump. Current blasting practice is ore-waste blasting. Ore-waste blasting is the term where the ore and waste rock are blasted in the same blasting process. Blasting is conducted by using nonel initiation system. By multiple pits operation, monthly powder factor is varied from 0.23 kg/t to 0.27 kg/t. Emulsion blend with density 1.15 g/cc is used as bulk explosive. At this stage, the concept of geoblast is proposed as an engineering tool for Drill and Blast engineering practice in PT.IMK. In addition, there is a need to maintain rock fragmentation by blasting, to maintain monthly powder factor, and to maintain excavator’s productivity. Next, the concept of scaled depth of burial (Chiappetta and Treleven, 1997) and the concept of blastability index (Lilly, 1986) are proposed as geoblast’s tools to improve blasting practice in PT.IMK. It is expected that rock fragmentation by blasting, explosive consumption and excavator’s productivity will be maintained by integration of geoblast and drill and blast engineering. Furthermore, the objective of this paper is to integrate geoblast and drill and blast engineering in order to create an engineering guideline in PT.IMK. Additionally, blasting trials with air decking application is proposed in order to support the geoblast’s improvement. It is planned that these blasting trials will be conducted in 2022. In conclusion, it can be seen that integration of geoblast and D&B engineering in PT.IMK is relevant to improve current drill and blast current practice and applicable to maintain rock fragmentation by blasting.

Nov 29, 2022

By M Lee, J F. Carswell, G Reitsema

"The increased costs of underground mining have continually challenged engineers to identify opportunities for alternatives to common approaches to underground development. Considerations to the design of horizontal and vertical development at the Dugald River mine targeted inclined raise boring to reduce horizontal development, not only to reduce cost, but to allow development activities to focus on other areas of the mine.The mine plan consists of 50 raise bored ventilation shafts, of which 17 have been mined to date with diameters ranging from 3.1 m to 5 m and lengths from 30 m to 200 m. The expected performance and stability of these shafts has been determined using methodologies proposed by McCracken and Stacey (1989) and further refined by Peck, Coombes and Lee (2011). Actual raise performances have been collated and compared to a database of raise bore performances across Australia as presented by Coombes, Lee and Peck (2011), and form a database of raise bore performance specific to Dugald River.Opportunities to further optimise the mine plan and reduce costs have seen the introduction of large diameter-inclined raise bored ventilation shafts to minimise the required lateral development to connect the ventilation circuits. Large diameter inclined shafts ranging between 3.1 m and 4.5 m in diameter have been successfully mined with dips down to 70°, reducing the cost of lateral development by more than $1 million over the next two years.Both technical and operational challenges were overcome in the mining of large diameter-inclined raise bores, including modification of: existing methodologies of assessing shaft wall stability for inclined raises. These included variations of the McCracken and Stacey method and the utilisation of the modified stability number (N’) previously developed for stope performance (Potvin, 1988). both the collar and toe development profiles, including the general set-up of the raise bore drill rig to reduce the operational risks associated with angled raises.Due to their success, inclined raises have been designed for subsequent stages of the life-of-mine ventilation system at Dugald River. This has resulted in significant capital cost savings for the mine.CITATION:Carswell, J F, Reitsema, G and Lee, M, 2017. Vertical and inclined raise bore performance at Dugald River mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

By Kam KM, Tran B

Statistical techniques of Box and Jenkins (1976) have been used to assess the existing control schemes and determine the dynamics of flash smelting furnace at the Kalgoorlie Nickel Smelter. Pertinent process variables, such as, oxygen flow, flux flow, matte grade and iron to silica ratio in slag, were considered in the analysis using routine operating data collected over two periods of operation. Results indicate inadequate control of some of the important variables. Dynamic characteristic parameters (dead time and response time) between a set of input and output variables were identified to improve optimisation of the existing thermodynamic model used for flash furnace control.

Jan 1, 1996