Search Documents

By G A. Ekama

This paper describes a novel system for the biological sulfate reduction (BSR) of acid mine drainage (AMD) using primary sewage sludge (PSS) as carbon source in an upflow anaerobic sludge bed (UASB) reactor configuration. A UASB reactor was operated at a temperature of 35¦C and it received PSS (1875 mg/L COD) augmented with sulfate (1500 mg/L SO42-). The experimental results indicate that a high treatment efficiency was achieved at more than 90 per cent sulfate reduction at a liquid hydraulic retention time (HRT) of 13.5 h. In this study, the effects of various operational parameters were also investigated. The effect of a biomass recycle stream from the top to the bottom of the sludge bed was found to initiate rapid BSR from the bottom of the bed. Profile tests showed that effective and immediate sulfate reduction was achieved as soon as the influent entered the reactor. From these results, it can be concluded that the UASB configuration using PSS as energy source would be a viable method for the BSR of AMD.

Jan 1, 2009

Effect of pH and Chain Length on the Flotation Separation of Fluorite from its Synthetic Mixtures with Calcite and Dolomite with Imino-Bis-Methylene Phosphonic Acid

Sep 13, 2010

Leading Article from "British Medical Journal," London, 4th, November, 1944.Assuming that silica exerts its injurious effect upon animal tissue through a slow transformation into silicic acid, Denny, Robson, and Irwin thought that if the solubility of siliceous material retained in the lungs could be suffciently reduced the usual fibrotic response could be diminished or prevented. They discovered that aluminum powder rendered siliceous material insoluble in vitro by coating the silica particle with a thin film of gelatinous hydrated alumina, which on drying formed crystalline alpha aluminum monohydrate. The presence of this adsorbed layer on the surface of the quartz was shown by staining it with aurin. That metallic aluminum dust produced no fibrosis in the lungs was demonstrated by dust-inhalation experiments on eight rabbits. Attempts were therefore made to prevent silicosis by mixing quartz with metallic aluminum dust.Animals exposed to quartz dust developed typical silicosis in about five months, but the addition of 1 per cent. aluminum powder prevented this even after exposure had been lengthened up to 22 months, provided the aluminum powder was of a particle size below 5. This year Crombie, Blaisdell and MacPherson have reported the treatment of 34 silicotic miners by the daily inhalation of fine aluminum powder freshly ground from small aluminum pellets in a specially constructed mill. Daily treatment began with five-minute inhalations, which were gradually increased to 30 minutes. Some of the men received 300 treatments, but the majority only 200. Out of the 34 cases thus treated clinical improvement was manifested by lessening or disappearance of shortness of breath, of cough, of pain in the chest, and of fatigue. In 15 cases the condition became stationary and remained so in spite of continuous employment in silica dust throughout the treatment. The progress of the disease was assessed by means of tests for respiratory function repeated at three-monthly intervals. Obviously this treatment cannot be regarded as a cure for silicosis, since it cannot restore lung tissue which has undergone fibrotic change; but Crombie and his colleagues believe that the inhalation of finely particulate aluminum powder offers every prospect of preventing the development of human silicosis.In view of these findings, it is surprising that repeated papers by Goralewski from Germany describe various types of lung disease attributed to aluminum dust, and press for them to be scheduled under the Workmen's Compensation Act in that country. Seven hundred workers were investigated. They were making, probably by a stamping process, aluminium powder containing about four milliards of particles of dust per grain, and are reported as complaining of dry cough with pain on breathing, shortness of breath, poor appetite, and gnawing abdominal pain. Spontaneous pneumothorax developed in four workers. No abnormal physical...

Jan 1, 1945

By J Kovacs

Underground development drill and blast practices have generally remained unchanged for decades. Historically, development optimisation has focused mainly on the application of perimeter control products in order to reduce overbreak, and efficiencies in development cycle times to increase advance rates. In today’s environment of ever increasing operating costs and lower ore grades, it has become even more critical to focus on the optimisation of drill and blast in development mining. It is a crucial component in ensuring mining schedules are maintained, but more importantly achieving the objective of getting to the orebody in the shortest possible time.This paper will focus on the development optimisation process used in a trial at Xstrata’s George Fisher Mine in North Queensland. Not only did the trial include the typical optimisation areas of charge loading practices, perimeter control methods, drill design standardisation and quality control processes, it also investigated the significance of delay accuracy with regards to perimeter control and drill design optimisation.One of the key measures of the trial was a comparative analysis between baseline development and development with the staged introduction of optimisation elements using 3D photogrammetry as a validation tool. A detailed cost analysis between the various stages was also a key measurable of the trial.The results of the work undertaken at George Fisher have shown that the accuracy of electronic detonators can produce significant benefits in development blasting. When combined with standard optimisation philosophies a substantial reduction in overbreak, ground support requirements and development cycle times can be achieved, whilst still being able to reduce the overall development operating costs.CITATION:Kovacs, J, 2014. Mine development optimisation – an evolutionary process, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 51–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

When a joint venture is established between a major and a minor, the co-venturers often have a number of divergent interests; the major may have put up significantly more capital into the project and will want to protect its investement; the major may have more financial resources and be more readily to commit capital to the project; the major may have more technical resources and expertise to provide to the project; the major may have other competing demands for its capital; the minor may be relying on rapid development of the project as its sole source of cash flow. Successful joint ventures arise when the co-venturers understand each others' interests and attempt to satisfy these interests. This could be achived by having a clear process and timetable for development of the project coupled with clear rules for distribution of income, the commitment of capital to the project and the provision of inter-company services. If divergent interests are either regulated clearly or eliminated, both co-venturers are more likely to seek common objectives in the joint venture with less scope for conflict. This paper, written from the perspective of a major, examines means of establishing successful joint ventures between majors and minors.

Jan 1, 1997

By E A. Amaral Jr, A C. Chieregati, J C. O Souza

Cross-belt samplers are designed to sample particulate material in processing plants, usually when there is no space to install a conventional linear falling stream sampler. Most of the available cross-belt samplers are mounted on the top of conveyor belts, and remove each increment from a loaded moving conveyor with a 360° rotation of an open faced cutter, in a plane perpendicular to the material flow. Despite the practicality of this equipment and the fact that it occupies very little space in the plant, cross-belt samplers are well known for collecting biased samples, especially due to the increment extraction error. Sampling consultants around the world tend to condemn this sampling equipment, claiming that it is incapable of collecting the fine material from the bottom part of the load, and, since the sampling probability is not uniform for all fragments and depends on its position in the stream, this kind of sampler generates biased samples and its use should be avoided. Furthermore, the greater the segregation effect between particles, the larger the bias. However, some plants, whose initial design did not plan for the installation of a falling stream sampler, must rely on cross-belt samples for process control and reconciliation. For the past years, sampling equipment manufacturers have been putting effort in modifying the cross-belt sampler design in order to comply with the principles of correct sampling. Changes to the cutter material, shape, position, speed and movement in relation to the material flow have been made, and are continually being tested for different types of ore with various chemical and physical characteristics. This paper presents the improvements made to a cross-belt sampler at a gold plant feed in Brazil and describes the tests performed until it was possible to validate the new sampling equipment for reconciliation purposes.CITATION:Chieregati, A C, Amaral Jr, E A and Souza, J C O, 2017. Validation of a modified cross-belt sampler for reconciliation purposes, in Proceedings Eighth World Conference on Sampling and Blending , pp 247–254 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Finlayson EJ

New detailed mapping, micropalaeont- ology and isotopic dating have been successful in revising the stratigraphy of Woodlark Island. All Middle to Late Miocene intrusives and volcanic rocks have been assigned to the Okiduse Volcanics. In addition, the results demonstrate that the Tabukui beds and Wonai Hill beds (N9, late Early Miocene to earliest Middle Miocene) are a single unit. Similarly, the Nasai and Suloga Limestones are confirmed as a single stratigraphic unit as they yield similar foraminiferal ages (upper Te, Early Miocene), and both occur in the same stratigraphic position unconformably overlying basement Loluai Volcanics. Radiocarbon dating suggests a latest Pleistocene age for the upper Kiriwina Formation. Extensive Quaternary cover and low relief prevents detailed structural airphoto interpretation. In general, the structure is simple with all units on Woodlark dipping to the northwest a_4 exhibiting prominent local block faulting.

Jan 1, 1991

The underground coal mining industry in Australia has, in the last 30 years, undergone a revolution in production methods, techniques and results probably unparalleled elsewhere in the world. It can lay claim not only to leading the fight against pneumoconiosis and setting high safety standards generally, but has at the same time recorded comparatively high rates of increase in output per man shift. The latter has been achieved as a result of progressively matching the latest in production and underground transportation equipment with significant changes in seam development and extraction techniques and the introduction of stress-relieving extraction methods unique to the world scene. However, the seam recovery factor is still too low. Apart from the overall objectives of maximising production and commercial returns with the greatest safety, there must be a concentration towards maximising seam recovery, particularly in high seams. The search will continue for systems which are more completely continuous mining operations than the present stop-go operations, with longwall having long term potential in this regard, but as yet not sufficiently developed to engender confidence for its more general use. Techniques developed in the last 10 years make the development and extraction of deeper seams, perhaps to 2500 feet or more, feasible with continuous miners as well as longwall. The future will see a greater use of continuous shifts at mines, larger mines with more sophisticated management organisation, extensible belts at the face, better systems of immediate roof support at the face, remote operation of face equipment, greater use of roof bolts and the longer roof cables. With commercial confidence in coal mining now virtually assured to at least the turn of the century, the stage is set for heavy capital development in the industry which will undoubtedly include major research into the whole area of mining methods and equipment. We must ensure that our contribution to such research equitably matches other coal producing countries.

Jan 1, 1975

The risks faced by organisations are part of a risk continuum. They can be evaluated in terms of hazard, uncertainty and opportunity as well as by the degree of influence they have on conformance, operating performance and strategic objectives. This paper discusses the application of risk management techniques for mitigating blasting hazards, reducing blasting output variability, and implementing blast improvement opportunities. Effective risk management practices can identify and evaluate risks across all levels of the continuum and can deliver realistic assessments of the likelihood and impact of risks on the companyÆs safety and business objectives. This paper does not attempt to present technical details about blasting, rather it aims to provide enough blasting context and examples so that the practical benefits of applying the risk management process to blasting can be fully appreciated. The topics discussed include: explosive management plan; statistical process control; quality blasting, rock-on-ground; Blast Management; Mine to Mill optimisation; and blasting information systems. The concept of a blasting risk management system employing a continuous improvement loop is also introduced. On reflection the insights presented should be extremely useful for observing and understanding which risk face has management focus at a mine site or for a blast site.

Jan 1, 2001

The Closure Risk model was developed as a new tool to aid decision makers in the complex area of mine closure. It uses a simple analytical technique that allows the decision maker to simplify what is often a complex mine closure process into more easily managed sub components. This systematic approach ensures that critical factors in the closure process are not overlooked. It also allows the most important issues to be highlighted. The model can also be used to produce quantitative estimates of risk by weighting and prioritising the issues to produce the Closure Risk Factor (CRF). Field trials at several mine sites in the Northern Territory of Australia in 2001 tested the model. The trials confirmed that the model has significant potential as a tool for decision-makers to assess in a structured, systematic manner, the major closure risks at individual mine sites. The risks include not only environmental impacts but safety and health, community, legal, financial, technical and other issues. The trials confirmed the value of a team-based approach and the inputs of key staff including environmental, production, mine planning, and community liaison personnel as well as mine management. Although the usefulness of the qualitative component of the model was established, it was found that, due to the influence of subjectivity, the utility of the prototype model to determine quantitative risk was of limited value. Using a continuous improvement approach, improvements to the model were sought. A refined model, incorporating the Australian Standard 4360 definition of risk and facilitated in-house risk assessment sessions was developed and tested against the data obtained in the field trial. This model, while maintaining the qualitative strengths of the original, allows more accurate absolute and relative quantitative scores to be calculated. This in turn facilitates comparisons between the issues at a single site as well as between different mines.

Jan 1, 2003

By M S. Henderson, R D. Alorro, L G. Dyer

An alternative leaching system for rare earth element recovery from monazite is under development. The initial stage utilises oxalic acid to convert the rare earth phosphate into an oxalate salt through dissolution and reprecipitation and it is the efficiency of this stage that governs the overall recovery achieved. It has previously been proposed that lixiviant consumption is the primary limitation in this process. This work further investigates a range of conditions in an attempt to further elucidate the factors influencing the achievable conversion in this stage. It has been shown that the pH may be governed by multiple reactions both consuming and producing acid (thus the mild change over time). The importance of proper mixing and potential to operate at lower temperature with only moderate impact on kinetics has also been demonstrated. Staged/sequential leaching is more effective in fresh solution as opposed to restoring the lixiviant concentration with subsequent reagent addition, suggesting some impact of solution composition. However, contrary to previous findings, subjecting the leach residue to fresh solution resulted in significant decline in leach rate and overall dissolution. This may be because a greater proportion of conversion was achieved in stage 1 in this work than in previous investigation. This may indicate that eventual passivation or the presence of some more refractory REE minerals limits dissolution. Iron dissolution was relatively consistent upon exposure to fresh solution, displaying the ability of the solution to continue to leach the goethite component of the concentrate.

Aug 24, 2022

For several years, the Geology Department of the University of Canterbury has hosted a series of postgraduate projects in the field of coal studies, supported principally by the Ministry of Energy and to a lesser extent by private companies. These projects have involved mainly West Coast Coalfields, and my own studies have focussed on inorganic geochemical aspects of West Coast coals. Because of the large number of potentially important analyte elements in coal, and the wide diversity of coals occurring in the West Coast region, this project has required a substantial amount of work to be spent on sample collection, sample preparation, development of analytical methods, and actual analysis. Considerable problems must be faced at the sampling stage: Can sufficient information be obtained from whole-seam composites, or should seams be sampled in plies. Ply analysis is preferable, but results of proximate analyses are usually available for composites only. Where multi-seam drillhole samples become available (eg Greymouth Coalfield, where some holes yielded more than six sampled seams), the ply option involves a dramatic increase in the number of samples. I have attempted to strike a workable compromise between geographical coverage of coalfields, and detailed sampling of individual seams at each locality. In many cases, sample material has been used jointly with Jane Newman who has carried out petrographic studies.

Jan 1, 1985

Bendigo Mining operates a 600 000 t/a comminution, gravity, flotation and leaching processing plant for the recovery of gold from their Kangaroo Flat Operation, in the Bendigo goldfields. The free gold and gold bearing sulfi des present are typically coarse grained and hence are highly amenable to gravity recovery. Plant operating data is consistently showing that over 78 per cent of the feed gold is recovered in a circuit, consisting of inline pressure jigs, inline spinners followed by free gold tabling and intensive leaching of tabling tails. The circuit receives coarse crushed product from high pressure grinding rolls and the grinding mill discharge, which allows material to be re-circulated through the gravity process until the particles are small enough to enter the flotation circuit. A plant audit was completed on 26 November 2009 designed to give an indication of the overall operational characteristics of the gravity circuit including single pass efficiencies of associated equipment. The techniques, results and challenges of such a survey are discussed.

Aug 1, 2010

Taking the Presidential chair of the Australasian Institute of Mining Engineers, my first duty is to thank you for the high honour and position you have conferred on me. A position entailing the highest compliment the Institute could bestow on any of its members, and one which I feel my inability to properly fulfil, inasmuch, as you have men in your ranks of the highest scientific training residing on that great continent where the head quarters of the Institute is established, while my engagements here will not permit me leaving this colony but for a very limited period.About six years ago, during the time the mining boom was at its height, there came to this colony from England, Germany, and South Africa, several mining engineers, who in conjunction with the mining engineers here, formed an Institute which we soon found we were not able to maintain. The mining boom gradually died away, and many engineers have left the colony to find employment in other parts of the world. We made overtures to your Iqstitute to take us under your wing, which you were kind enough to do, and the outcome is that you have come over 1200 miles to hold a meeting in New Zealand. The paucity of members residing in this colony does not admit of a large attendance; but we heartily welcome you to our shores and hope you will enjoy a holiday visiting some of the principal mining centres and exchanging ideas, which not only improves our minds, and widens our field research, but also tends to lead to further economic improvements in the extraction of metals the earth contains...

Jan 1, 1903

By P Holtham, K Duffy, W Valery, A Jankovic

As high grade ore deposits are depleted, remaining deposits are generally lower grade and require the mining and processing of larger volumes of material per tonne of product. These low grade deposits often contain a large proportion of barren gangue. Pre-concentration aims to remove this barren material at as coarse a particle size and as early in the process as possible. This has the potential to reduce processing costs, energy and water consumption, increase production and improve resource utilisation.There are several technologies that may be applicable for pre-concentration. This paper looks specifically at bulk ore sorting and how it can be integrated into existing or new mining operations to improve profitability and reduce environmental impact. Bulk ore sorting is the separation of barren gangue from a fully loaded conveyor belt based on the grade as measured or inferred from a sensor measurement. It may be used to increase the production rate through fixed plant capacity, or increase production and/or reduce the size of downstream processing equipment in Greenfield operations. Marginal ore sub-economic reserves may be upgraded, making them economic to treat and improving the resource utilization. Bulk ore sorting could also be used to reduce dilution and ore loss in mining operations by improving grade control, or to separate ore types to treat via different process routes. Various applications of bulk ore sorting are discussed in this paper, and three cases are investigated considering the impact on the overall operation and the associated benefits.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Integrating bulk ore sorting into a mining operation to maximise profitability, in Proceedings MetPlant 2015, pp 273–287 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Akerkar D. D, Dey M. L, Mathur S. B, Chowdhury S. K R

The extraction of gold and silver from chalcopyrite concentrates has been investigated. In view of the recent interest in non-cyanide leachants for gold and silver, one such alternative reagent, namely thiourea, has been employed in the present work. Precious metal leaching was attempted from received copper concentrates as well as pre-oxidised concentrates. Pre-oxidation of the concentrates was carried out by three different methods, namely roasting, pressure oxidation and biological oxidation. After pre-oxidation and leaching of the base metals, the leach residues were subjected to further leaching for precious metal extraction. The results obtained on the extraction of gold and silver from received concentrates as well as pre-oxidised concentrates are presented and the effectiveness of the three pre-oxidation routes employed is compared.

Jan 1, 1992

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Study of Bauxite Separation by Using Flotation Column

Sep 13, 2010

By R Austerberry, S Green

Highly weathered ground, limited collar options and the need to achieve a desired outcome at the lowest possible cost led to the need to adopt a construction approach that had no established design methodology. The newest ventilation shaft at Mandalay Resources’ Costerfield Operations had to be established to a depth of 30 m through poor ground best described as ‘sticky swelling clay’, some of which was contained within an old backfilled pit.The ability to excavate a traditional presink was not possible due to limited space and the introduction of men into the shaft was to be avoided due to the associated safety risks and corresponding increase in cost. Piling in conjunction with raise boring and remote fibrecrete application was identified as a possible solution that could achieve the desired outcome at an acceptable level of risk.Construction of the piles was challenging and required continual refinement until an acceptable level of productivity could be achieved. Limitations on concrete delivery was taken into consideration to ensure hole stand-up time was acceptable and re-drills were not required. The adoption of a set process from alignment, drilling, concrete placement and testing ensured the desired design was achieved. Mine operators should consider the use of piling as a method of shaft stabilisation for the portion of raise bored shaft that passes through the weathered zone.The importance of quality control and attention to detail through the entire shaft construction process cannot be underestimated as issues such as insufficient geotechnical investigation, pile and pilot hole deviation, concrete and fibrecrete quality, as well as delays in the application of fibrecrete can place the success of the project at risk.This paper outlines key learnings from a client’s perspective with regards to the concept, planning, design, execution and completion of a 3.1 m diameter raise bore shaft through both weathered and highly structured ground at the Augusta Mine.CITATION:Green, S and Austerberry, R, 2014. Piling and raise bore construction – key learnings from a client’s perspective, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Bioleaching of Weathered Saprolite - Heavy Metal Adaptation Mechanisms of Aspergillus foetidus Nickel laterite ores remain important to the future supply of Ni and Co as they contain the bulk of known nickel and cobalt reserves (80 per cent and 90 - 95 per cent respectively). Current commercial extractions of Ni and Co from nickel laterite ores are energy intensive and operational costs are high. Microbial leaching of oxide ores has the potential to offer a much needed step-change in the technology for processing laterite ores. Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. Optimisation of the process in in-situ application, however, has been hampered by the toxicity of the heavy metals that are being leached by the organisms. Our recent study has shown that organisms are able to develop tolerance towards heavy metals by adaptation. This study examined the extracellular metal detoxification mechanisms of A. foetidus in 0.2 per cent (wt/v) to 0.7 per cent (wt/v) of weathered saprolite ore. To support our analysis, FTIR, CHNS and microscopy were used to confirm the participation of specific functional groups in the extracellular detoxification process.

Sep 13, 2010