Search Documents

Study on Rational Process Flow Sheet for Beneficiating Low-Grade Cu, Mo, Bi, S, W Polymetallic Ore

Sep 13, 2010

By B Ellis

Brunswick Mine is one of the largest underground zinc/lead mines in Canada, producing 3.4 million tones of ore annually. As mining activities advance to deeper levels, ground pressure also becomes greater. To cope with the highly stressed ground, the mine has taken some strategic measures to ensure the targeted production level. Such measures include the implementation of a pastefill system and transferring the mining method from primary/secondary stoping to pillarless pyramid stoping. With the pillarless mining method, stope sizes become smaller and the number of active stopes is also less than before. In addition, mining sequence and cycle time have to be strictly followed according to production schedule. The blasting project described in this paper tackles one of the steps in the mining cycle aimed at shortening the blasting cycle time in a stope. Furthermore, this project was conducted and managed with the Six Sigma initiative in Noranda which was implemented in the fall of 1999. Like a typical process review, the blasting operation was examined by breaking it down into many steps that can be quantified and measured. Each activity was then correlated with different factors associated with blast design as well as blast operations underground. It was found that the utilisation of voids plays a key role in the blasting cycle time. With improved void utilisation ratio, blasting cycle time has been reduced from an average of 12 shifts to ten shifts per stope. This improvement translates into approximately 180 000 tonnes of ore being blasted without any increase in manpower. This paper presents the technical aspects of the study, as well as some operational issues and improvements made during the project.

Jan 1, 2001

Gippsland has perhaps the most colourful history of exploration of any area in Australia. Hydrocarbons were first discovered in the Gippsland Basin in 1924 when a water well at Lakes Entrance encountered oil and gas shows. In 1942, the Commonwealth and Victorian Governments, in an effort to supplement a wartime oil shortage, sank a shaft near this well and produced 8000 barrels of low gravity oil up to 1956, when the field was abandoned. A total of 64 shallow wells had been drilled in the Lakes Entrance area by that time. Elsewhere in the onshore Gippsland Basin, 30 wells were drilled from 1925 to 1941. In 1960 BHP Ltd was granted an exploration permit covering much of the offshore area of the Gippsland Basin. Esso Australia Ltd joined BHP in 1964 and drilled the Barracouta-1 gas discovery in 1965. Since then over 100 exploration and appraisal wells have been drilled in the basin resulting in the discovery to date of some 3.6 billion barrels of recoverable oil and 8.8 trillion cubic feet of recoverable gas (Current remaining recoverable reserves are 906 million barrels of oil and 5.7 TCF of gas). Exploration in the offshore areas is actively continuing today and new discoveries are still being made.

Jan 1, 1992

By S Dirdjosuwondo, R Plaisance, L Thoma

PT Freeport Indonesia, a subsidiary of New Orleans-based Freeport McMoran Copper and Gold of New Orleans, operates a large mining complex on the Western half of the Island of New Guinea in Tembagapura, Irian Jaya, Indonesia. The IOZ (Intermediate Ore Zone) mine, one of the underground orebodies, is mined by block caving. The area affected by the cave collects a large quantity of rain and ground waters mixing with fine rock particles. The mixture, commonly called æwet muckÆ, sometimes spills into drawpoints and makes the working environment hazardous to the loader operators. Wet muck is observed in an increasing number of drawpoints in the IOZ mine and remote LHD (Load-Haul-Dump) technology has been implemented to handle the ore. The driving force for this automation project has been the safety of the loader operators. The system has been developed mainly in-house and incorporates state-of-the-art features. Up to eight remote loaders and nine rock breakers are controlled from an underground control room located approximately 400 metres from the active extraction panels. The two underground crushers and nine conveyor feeders are also operated remotely from an adjacent control room. The development of FreeportÆs remote system has taken time and considerable effort. Not only the success of the IOZ mine was at stake but also the fulfillment of environmental commitments pertaining to the mill tailings. Approximately eight per cent of the mill feed must come from underground skarn deposits to neutralise the acid-generating tailings generated by the huge Grasberg open pit ores.

Jan 1, 2000

By K Buda, W Staunton, M Hill, V Tjandrawan

One of the challenges facing the gold industry in the 21st century is the continuing need to identify new reserves of economically treatable ores. Discoveries of large, metallurgically simple orebodies are becoming increasingly rarer, forcing companies to investigate options for the processing of ores which may present recovery, economic and/or environmental issues, requiring innovative approaches to their treatment. Ores which contain naturally occurring carbonaceous material (æpreg-robbing oresÆ) are an example of one such ore type. NewmontÆs Jundee operation contains zones of carbonaceous ore within the oxidised orebody. A program consisting of detailed laboratory work and extensive plant trials has been undertaken to assess the options of the processing of this material. Laboratory tests demonstrated the advantage of carbon-in-leach (CIL) over direct cyanide leaching and carbon-in-pulp (CIP) for treatment of these ores. The laboratory program identified several factors which would enhance overall gold recoveries where preg-robbing ore was being processed, including: keeping preg-robbing ore separate from non-graphitic ore; maximising gravity recovery; and ensuring the plant operates in æpureÆ CIL mode, ie no leaching prior to first adsorption tank. Several plant trials were undertaken to assess the economic sustainability of treating moderate preg-robbing ores through a modified gravity/leach/adsorption circuit. Results indicated that where good operational control of the circuit was maintained to ensure high gravity recovery, minimal leaching prior to carbon contact, and maintenance of good, active carbon inventory, then acceptable and sustainable overall gold recoveries could be obtained. Using these relatively simple plant modifications potentially allows a plant to treat ores with preg-robbing index (PRI) values up to one. When PRI values rise to 1.3 - 1.6, leach recoveries can drop from >85 per cent to

Jan 1, 2007

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011

By S Pradhan, A Kuras, R Mahajan

This paper describes the design of the precast concrete segmental lining for the 13.1 m internal diameter and 450 mm thick, 2.4 km long mainline tunnels for the Waterview Connection project in Auckland for the New Zealand Transport Agency.The design and detailing of this segmental lining presented some noteworthy challenges, including an alignment that has sections of low cover in soft ground. Key points of interest are that this precast segmental lining is the largest to ever include steel fibres as the primary method of reinforcement and the lining includes cams on circumferential joints to control ring deformation.The paper describes some of the key design decisions that were made in a collaborative manner with the construction team, tunnel boring machine manufacturer, segment manufacturer and the designers.CITATION:Mahajan, R, Kuras, A and Pradhan, S, 2014. Design of segmental lining for Waterview Project, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 289–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Choulaj D

Mining and petroleum continue to be the two most vita components of our nation's development, says Sir Julius Char in the Australian Journal of Mining (Nov-Dec 1996). In fact the} account for 71.6% of export earnings, and 21.2% of Gros; Domestic Product in Papua New Guinea. The Misima and Porger, Mines, along with the Kutubu oil project, have essentially rescues PNG's economic viability since the loss of income from Panguna Though the industry cannot create employment in the manner o. intensive industries such as agriculture, it does provid( opportunities to local communities in terms of jobs, financia compensation, and infrastructure. Many ventures take many years and enormous capital investment to set up. There are three phases: exploration, feasibility, an( operations. The operations phase sees a massive development o infrastructure, or the actual `building' of the mine. For mining companies to commit to such lengthy time frames and high level: of investment, without returns, requires confidence and a degree of commitment from government on a number of levels - legislative stability, monitoring social development, and the provision o social infrastructure.

Jan 1, 1997

By R P. Callaghan

Underground production from the low grade copper orebodies at Mount Lyell in recent years has involved surface subsidence of open cut areas. Relevant structural and lithological features of the geological environment are described. The highly mechanised underground mining system involves sublevel caving and sublevel open stoping with associated hanging wall cave. Monitoring of subsidence and caving has been made by regular visual inspection and measurement of crack development, and by surface profile surveys. These simple techniques have proved adequate in assuring management that ground movement is proceeding normally and safely.

Jan 1, 1980

Heap leaching of copper sulphide and oxide ores' has been conducted at Rum Jungle since the end of 1965.A review of operations was made and this led to an examination of some theoretical aspects of copper sulphide heap leaching. Ox,ygen diffusion was indicated to be the factor controlling copper leaching rate at Rum Jungle and in other similar operations. Suggestions are made for measuring the heap leaching rate. Prediction of full scale operational results from pilot scale testwork are discussed.

Jan 1, 1969

By Mukhopadhaya K. K, Cory A. H

The concept of using travelling magnetic fields created by linear motors was stimulated by Laithwaite who advanced ideas on motors with shaded poles (Laithwaite, 1968), rack and pinion motors (Laithwaite, 1970) as well as low speed, brushless motors and three dimensional motors (Laithwaite, 1973a and 1973b).Sudan (1963) and Sundberg (1969) had applied the concept to metallurgical processes. However, the use of travelling magnetic fields has not been used widely to produce conditions for the separation of magnetic from non-magnetic minera1s or even magnetic materials from non-magnetic materials, although some attempts were made by McCarthy (1922), Davis (1934), Dean, Gottschalk and Davis (1934) and Gottschalk (1934).Laithwaite (1973, a) while working with linear motors made suggestions for designing separators and in the work described here, the observations of Laithwaite and others are extended to determine the characteristics of the motor with a view to using it as a magnetic separator.

Jan 1, 1980

By P N. Holtham

Magnetic separation is routinely used in the processing of titaniumminerals, and the efficiency of these operations can be determined bymeasuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved.This paper describes the development of an inductance-basedinstrument for measuring very low levels of magnetic susceptibilityon-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance.A prototype instrument has been installed in the zircon scavengercircuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction.Using the instrument, the zircon content of this stream can now beaccurately determined from the measured magnetic susceptibility,provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By Russo S

Metals Refining Operations Pty Ltd (MRO) began refining gold in PNG in 1991 and has undergone continuing growth since then in servicing an everchanging and growing market. MRO's ownership combines PNG Government interests and Golden West Refining Corporation Limited as operator.Features include a very diverse range of suppliers, a full range of technical methods and challenges and the financing and marketing responses unique to a developing country. These areas are examined and documented with special emphasis upon the service needs for the gold industry and future trends and challenges are discussed.

Jan 1, 1997

By Griffiths J. B

From its mining lease at the northern end of Cohens Reef at Walhalla in the North Gippsland Mountains, the Long Tunnel Extended Gold Mining Company produced 13,695 kg of gold, which at 1980 prices represents a value significantly in excess of $200 million. In the period 1885 to 1908 the mine was one of Australia's principal reef gold producers, being top Victorian producer in six of these twenty-four years. Prior and subsequent occupants of the lease produced an additional 160 kg of gold. The Extended and the other mines on Cohens Reef whilst contributing importantly to the financial resource of Victoria, were the sole important support for the substantial town of Walhalla that had grown up around them. When the mines closed, Walhalla gradually reduced from a bustling developed town to the present attractive mountain village so favoured by tuurriSts. To allow the visitor to obtain a better ;ri.icrstanding of Walhalla's mining past, important parts of the Long Tunnel Extended Gold Mine workings and site are being

Jan 1, 1981

The carbon-in-pulp (CIP) process is now well established in the South African gold industry, with a total of over I million metric tons of material being treated each month in six large plants. This tonnage is derived from ground ore, from filtered pulp, from calcine, and from reclaimed sand-tailings dumps. With this new process and the new large plants, those concerned with CIP are experiencing a learning process, since each new plant presents a different set of problems to be overcome. The knowledge and experience gained from these plants is being shared, and will be of benefit in the design and operation of new plants. The CIP process can be subdivided into the following unit operations: prescreening at a fine size, adsorption, acid-washing and elution, reactivation, and electrowinning. Results concerning each of these unit operations, which were obtained from pilot plants and from large-scale CIP plants in South Africa, are presented. The latest developments in each of these areas is summarized. Tables that are included as an appendix contain some information concerning the equipment in these new CIP plants plus operating results from some plants.

Jan 1, 1982

In presenting this address I am conscious of the honour that has been paid me in my election to this important office, and I am very aware that I follow, in the position of President, many distinguished men who have led the Institute over the 70 years since its inauguration in Broken Hill in 1893.It is perhaps appropriate tonight that I intend to talk about a metal which recalls the birth-place of the Institute, and is also one with which I have had a direct association throughout the whole of my working career. This metal is Silver.Silver is associated traditionally in everyone's mind with money and silverware, and has always been prized for its natural beauty and elegance. It is today one of the few metals in which world consumption has outstripped production, and the events which have occurred to bring about this situation make an interesting story.In telling this story, I propose firstly to indicate our development as a silver producing country, give an historical review of the metal, trace its use as currency and the factors influencing its price, and then say something of the old and new uses of silver. Finally I shall give some comments on silver production in Australia today.Australia, with 6-5 per cent of the world's output of silver, ranks sixth among the producer countries and over the years has contributed 892.5 million ounces to the world's supply which, based upon production since the discovery ofAmerica, is estimated to have been 22,150 million ounces or nearly 680,000 tons.Although our production appears relatively small by...

Jan 1, 1963

By M Sherman

The challenge facing the engineering provider is to calculate throughput rates when faced with disparate specific energies calculated by different testing methodologies. Typically, an ownerÆs team would expect that the throughput calculations be checked using more than one method, therefore it is inevitable that there will be differences, based on which methodology is used. This engineering challenge is exacerbated by the continuing evolution of contemporary circuit configurations such as two stage pebble crushing with or without high pressure grinding rolls (HPGRs) as the second stage, or second stage pebble crusher product reporting to the ball milling circuit, etc.This paper is a companion to the paper first presented at SAG 2011, which showed that the Bond Indices are an excellent tool for estimating the specific energy requirements for semi-autogenous grinding (SAG) mills in single-stage SAG milling (SSS) circuits, SAG and ball mill circuits (SAB) or SAG and ball mill circuits with pebble crushers (SABC). This paper presents how the Bond Indices have been used to calculate ball mill specific energies, and therefore throughput rates, for SAG mill based circuits. Once the ball milling specific energy is known, tower mill and vertimill energy requirements can also be calculated. It is noteworthy that the method presented in this paper does not require the use of any unpublished correction factors: the proposed method uses the Bond parameters and equations published by Rowland in 1982.CITATION:Sherman, M, 2013. 21st century bond, in Proceedings Iron Ore 2013 , pp 309-312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By T Sylow, A Correa De Araujo, M Gotelip Barbosa

ArcelorMittal is among the largest world’s producers of iron ore. With a geographically diversified portfolio of iron ore and coal assets, it is strategically positioned to serve the network of steel plants, as well as supply the external global market. ArcelorMittal Mining has a global portfolio of 14 iron ore operating units across Brazil, Bosnia, Canada, Kazakhstan, Liberia, Mexico, Ukraine and the United States. Iron ore products include concentrate for sintering and pelletising, pellets, directly shipped fines and lump ore. This paper presents an overview of ArcelorMittal iron ore mines including iron ore typologies and the annual production of each unit. It will also briefly discuss the processing required in order to obtain marketable products.CITATION:Gotelip Barbosa, M, Correa De Araujo, A and Sylow, T, 2017. Overview of ArcelorMittal mining operations and research and development, in Proceedings Iron Ore 2017, pp 161–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Restarick CJ

The development of mathematical relationships to describe grinding in continuous rod and ball mills has involved two methods of approach and has resulted in two main types of "model." The first which has been used for full scale grinding systems has depended on the analysis of, for example, the effect of change in solids feed rate on the changes in overall size distribution which the feed undergoes to become the product as a result of passage through the mill operated under steady conditions. The resultant mathematical relationships are of matrix form and do not include any description of the flow characteristics of the systems. The second approach has made extensive use of a technique in which a "pulse" of selected tracer mineral, of chosen

Jan 1, 1970