Search Documents

By M F. Lee

In order to make good decisions, as to whether large diameter raise bored shafts can be constructed in blocky rock at a particular location, mine planners, management, geotechnical engineers and contractors must understand and consider a range of geotechnical issues. Firstly, mine management must ensure that adequate time and resources are available to find appropriate shaft sites. Deep weathering, adverse structures, groundwater, etc might mean that the most desirable location, with respect to other mine development, might not be suitable. Special site investigation drilling, etc may be necessary. Even then, alternative construction options might be necessary, other than just reaming through to the surface. A site investigation borehole should then be drilled to investigate specific and general ground conditions along the raise alignment. Often, only small sections of weak blocky rock dictate raise stability. While the empirical McCracken and Stacey method is typically used in Australia to assess raise stability and assess geotechnical risk, until recently it had no published performance data.An Australian database of raise performance now exists and is presented below, courtesy of an industry survey by the Eastern Australian Ground Control Group. Raise diameter and ground conditions (in terms of a lower bound Qr value) is presented for 50 cases versus raise performance.

Jan 1, 2008

By J Stojanovic, V Kasic

Gold-bearing polymetallic sulfide deposits are common in Serbia, and mostly occur in the Karpato-Balkan and, to a lesser extent, the Serbo-Macedonian metallogenic province. These deposits û Coka Marin (Majdanpek), Grabova Reka (Blagojev Kamen), Lece (Medvedja) and Veliki Cip (Boranja) û are dominated by Cu and/or Pb-Zn mineralisation that contains a variety of Pb, Zn, Cu and Fe (¦ Sb, As, Bi) sulfides and sulfosalts, as well as native elements. Gangue minerals are composed of quartz, carbonates and rare silicates and barite. Based on their gold content these deposits can be divided in three groups:1. Polymetallic deposits with a high gold content (>1 g/t).2. Polymetallic deposits with an intermediate gold content (0.1 to 1 g/t), and3. Polymetallic deposits with a low gold content (<0.1 g/t). Gold occurs as native gold or as an alloy with silver. Native gold ranges in size from 5 to 20 ¦m, with a few rare grains over 100 ¦m, as isolated grains or as microveins (in the first group of deposits). Its distribution within the deposit in uneven. Native gold in the second group is smaller in size (1 - 5 ¦m, rarely 20 ¦m), where it is uniformly distributed in a quartz-silicate matrix. The third group is of no economical importance. The subject of research has been the first group of polymetallic deposits.

Jan 1, 2008

The Bureau of Mines, with a history of mining research since 1910, still seeks improvement in safety and health along with improvement and competitiveness in the mining industry. Much promise of such improvements lies in new technology, and this is particularly the case in the still growing coal mine sector, although much Bureau research is long term, high risk, aimed at new concepts.The miner's environment is a primary concern, involving technologies of contaminant monitoring and control in high production scenarios. Contaminants arising from diesel use, alternatives to high speed rotary cutting and more efficient dust removal are being addressed, and drilling efficiencies, better monitoring through unitising operations and insitu rock dust monitoring are particular features.

Jan 1, 1991

The passage of a vast array of new State and Federal environmental legislation over the last couple of years has required many mine operators to sharpen their focus on environmental requirements. Established requirements, such as environmental impact assessment, minimising disturbance and rehabilitation must now be complemented by mine environmental management plans. These may not only require regular monitoring of mine operations and detailed forward planning to prevent or reduce environmental harm caused during mine operation, but annual updating. It is likely that in future these plans will be required to incorporate general principles such as pollution prevention, sustainable development, waste minimisation and conservation of biodiversity and ecological integrity.

Jan 1, 1993

By Grant JR, McKavanagh BM, Dear SJ

A geophysical technique of rock mass assessment for engineering purposes is being investigated and shows positive correlation with direct structural logging and mapping techniques for the detection of major geological features. The technique is cross-hole acoustic surveying incorporating high speed signal averaging, with a maximum hole separation in excess of 30 metres in hard unfractured rock masses. The bulk of the field test work was carried out in open stopes in the copper ore bodies of Mount Isa Mines Limited. The investigation forms part of an integrated study of blasting in mining, aiming for fragmentation control through blast design modification. The rock quality factor, Q, is presented as a blasting index and can be determined for a significant portion of a production stope.

Jan 1, 1981

By Henley S

The year 2000 is not very far ahead - only five years. It should not be hard to forecast what will happen between now and then, because the technologies that will be in practical use then should all be at least in embryo existence now. There has been a historical trend for the mining industry to work ever more difficult and ever more marginal deposits. There are clearly a few exceptions and major discoveries, but the industry is becoming heavily dependent, at both the exploration and the mining stages, on technological innovation to retain acceptable profit margins. With the new exploration and mining technologies come requirements for additional computing support. Computing technology further allows the potential integration of a wide variety of different types of data to help the explorationist to build and test exploration strategies, or to help the miner to design and schedule mining operations.

Jan 1, 1995

Sulfidisation Promotion Effect of Ammonium Sulfate on the Flotation of Copper Oxide Ores

Sep 13, 2010

In a country richly endowed in mineral wealth, Climax Arintco Mining Corporation's ICAMC) Dinkidi porphyry Au-Cu deposit in Nueva Vizcaya, Philippines, represents the most significant mineral discovery in this country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon, a region previously unassociated with porphyry -style mineralisation.Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.4 per cent copper. Regional exploration throughout CAMC's 37 000 hectare FTAA has identified a further 16 potential porphyry-related deposits.

Jan 1, 1997

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

Asarco's newest concentrator near Troy, Montana, began operation in October 1981, and is presently milling ore at its design capacity of 7,710 metric tonnes per day. The underground room-and-pillar mine produces a readily floatable copper sulfide- native silver ore in a quartzite gangue. Major sulfide minerals are bornite and chalcocite with minor chalcopyrite; fine grained native silver occurs with the copper sulfides. There are also minor amounts of native copper and copper oxides in the ore. A rougher copper-silver concentrate is floated, reground and cleaned twice. Cleaner tail is scavenged, and the scavenger concen- trate is combined with rougher concentrate for regrinding. Rougher flotation tailing and scavenger tailing make up final mill tailing which is disposed of by spigotting into a tailing dam located 10.5 km from the mill site.

Jan 1, 1978

By Whittaker B. N, Reddish D. J

The rockbolting method of support is employed widely in several countries in different of mines. Hard rock mines use this method extensively. Soft rock mines, such as coal mines, have employed standing supports (steel sets) as the main method, although some countries such as the U.S.A. and Australia have preferred rockbolting. There is increasing interest in extending the rockbolting method in coal mines. The application of rockbolting techniques in an industry which traditionally has not applied such techniques, has required the development of a systematic design approach. This design approach uses extensive monitoring, to asses the viability of the support system in differing conditions. Currently at a number of new and existing mine developments in the U.K., rockbolting is being successfully applied. Although, inevitably some localised geotechnical problems have been encountered and have needed to be taken into account. The effect of faulting on roadway conditions is discussed in this paper and a design approach has been applied using a numerical analysis method, namely the Finite Element Method. The results presented in the paper serve as a useful guide to roadway support designers, and in particular the role played by different bolts in a range of conditions.

Jan 1, 1992

By Boyd G. L

Stress measurement is at the core of most stability design analyses. It is demonstrated that contrary to accepted practice, it is the field measurement, and not the calculated prediction, of stress that requires most examination and review. Since it is not really possible to quantify rockmass properties, the stiffness values used in reduction of stress measurements and in subsequent design analyses (either empirical or numerical modelling) must consider an appropriate range of values.

Jan 1, 1995

By Amusin BZ

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By Pollard D. M

The BHAS copper-lead matte leach process, developed in Port Pirie, South Australia, has been in operation on a commercial scale since 1984. This process is one of many developed in the past decade to recover copper via the hydrometallurgical route. In essence, the process involves a single stage agitative leach of 100% -75um matte in an acid chloride-sulphate lixiviant with gaseous oxygen as oxidant. The leach temperature is controlled at 85¦C to assist with reaction kinetics. After leaching, divalent copper is recovered from solution via a conventional solvent extraction/electrowinning circuit to yield cathode copper for sale The BHAS matte leach process has several unique characteristics cf. other commercial oxidative acid leach processes. These include i) the use of gaseous 02 as oxidant ii) H2SO4 addition as make up acid iii) Relatively low chloride ion addition (30 g/1) For this reason, extensive work was carried out into the optimization of leaching by Meadows (1985). Variables investigated included ò Oxygen flow-rate ò Agitation intensity ò Leach temperature ò Free acidity ò Chloride ion concentration ò Matte particle size The current work was conducted to determine the effect of cooling rate, and hence mineralogy, on the leaching characteristics.

Jan 1, 1989

By Smith IEM

Some samples from arc-type volcanic suites collected in northern New Zealand and southeastern Papua New Guinea show rare earth element (REE) and Y abundances which are enriched relative to the those typical of their respective associations. This enrichment appears to be the result of an alteration process which selectively mobilises the REE and re-precipitates them as REE-bearing minerals in veins and interstitial patches. The alteration is on a micron scale and is not detected in routine petrographic examination. The spectre of REE mobility in young apparently fresh rocks is important to igneous geochemists who use REE abundances to constrain petrogenetic models and may also be important because it indicates the operation of a natural REE enrichment process which could operate in the formation of economic REE deposits.

Jan 1, 1990

Congratulations on your considerable enterprise in securing the opportunity to have this international conference here in Brisbane - and congratulations on your success in attracting such a distinguished audience from so many nations, with such a broad selection of papers. It is a notable achievement that in the year in which Australia is celebrating two hundred years since settlers first came fran Britain, The Australasian Institute of Mining and Metallurgy is responsible for some ten major conferences, of which at least four are specifically international, or have a very strong international involvement.

Jan 1, 1988

An analysis of pumping figures suggests that there are two distinct styles of water inflow patterns in Zambia's mines. Carbonate hosted orebodies (Kabwe and Nampundwe) display a characteristic seasonal variation in water inflow with peak pumping showing a short time lag with respect to the rainfall pattern. Aquifer characteristics are controlled by secondary, weathering enhanced, near surface phenomena. Non-carbonate hosted orebodies such as those of the Copperbelt (Konkola and Nkana) occur in successions of highly variable lithology and consequently there are stacked aquifers of variable character. Inflow of water does not display seasonal variation. The major factors affecting the amount of inflow are the structural setting, the geometry of the orebody and the local lithostratigraphy. Thus the Konkola orebodies which occur in a saddle shaped open ended basin result in what is probably the wettest mine in the world, pumping some 376,000 cubic metres of water a day.

Jan 1, 1988

By Paine GG

In coal mining each of the unit operations are interrelated with each preceding operation having an effect on subsequent operations. This presents difficulties for determining when the lowest overall costs for a particular mining system are achieved. Drilling and blasting is the first mining operation for production and is known to have an effect on the subsequent loading, hauling and crushing operations. Computer blasting models developed over the past 15 years can be used to describe the drilling and blasting operation. This paper describes the ICI Blasting Model "SABREX" in detail. Methods of using the model are discussed. This involves field measurements of geological structure, shallow refraction seismic surveys, laboratory measurements of rock properties and high speed photography of blasts. The predictions are compared with actual blast results for fragmentation sizing and muckpile profiles. Outputs from the model are described and these can be used for input to models of subsequent operations.

Jan 1, 1987

By Hill G

The Boddington Gold Mine (BGM) is managed by Worsley Alumina Pty Ltd (Worsley) and is located 110 km south-east of Perth, Western Australia. The gold mine, which has operated since mid-1987, was originally constructed to treat 3 Mtpa of gold bearing oxide ores, has subsequently been expanded to treat 7 Mtpa and is presently one of the largest gold producing operations in Australia.During 1990 a Supergene/Basement Plant was constructed to treat 250 000 tpa of copper supergene and hypogene ores and basement ores which contain significant gold grades and which are encountered at the lower levels of the existing oxide orebody. The SupergeneBasement Plant has the versatility to treat a wide range of ore types, producing both gold bullion and copper-gold concentrates. It is a stand-alone facility adjacent to the existing 7 Mtpa gold plant.

Jan 1, 1992

By Ö Aydan

Rock dynamics is one of the most important topics in the field of rock mechanics and rock engineering. The spectrum of rock dynamics is very wide and it includes the failure of rocks, rock masses and rock engineering structures such as rock bursting, spalling, popping, collapse, toppling, sliding, blasting, non-destructive testing, geophysical explorations, science and engineering of rocks, earthquakes, and impacts. Undoubtedly, the rock dynamics issues in Mars would remain to be the same. Although mankind has no direct access to Mars yet, the Mars exploration rovers (Opportunity, Sprit, Curiosity and Perseverance), Mars Reconnaissance Orbiter and InSight Lander provided very valuable data so that some rock dynamics issues can be recognised. The author reports his considerations on rock dynamics issues in Mars from very careful examination of images and data provided from MERs and MRO and discusses their implications.

Nov 29, 2022