Search Documents

By Ketteridge IB, Mulcahy DE, Quast KB

The long term energy demands in South Australia are such that there is a distinct possibility that one of the lignite deposits in the State will be exploited to feed a pulver- ised-fuel power station. Bowmans lignite deposit is the largest lignite deposit in South Australia and is considered to be a contender. The deposit is ideally situated (100 km north of Adelaide) but the quality of the lignite is poor (see Table 1). TABLE 1

Jan 1, 1984

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

By Eoffe SW

The wide application of computers in beneficiation plants has resulted in the creation of a number of complex automatic control systems at all stages of ore dressing processes. To create such systems it is necessary to solve complex problems of analysis and calculation. The application of computers to solve these problems demands development of simple and effective methods of investigation and simulation of ore dressing process dynamics because all the known methods are complicated in usage and cannot guarantee the desired accuracy and quality of process control. A new grapho-analytical method of investigation and calculation of ore dressing flow sheet dynamics, worked out by the authors of this paper, is based on proportion method development and is used to construct dynamic characteristics of the investigated processes. It is possible to use the given method for investigating benefication schemes with flotation machines having non-linear static characteristics and circulating loads. The suggested method of investigation of concentration flow sheet dynamics allows us to obtain dynamic characteristics of technological process parameters in both linear and non-linear systems. Moreover, the final result can be obtained without labour consuming analytical calculations by a simple graphical construction based on the static characteristics of the known equipment and processes.

Jan 1, 1993

By Burrell I

This paper describes recent developments at West Cliff Colliery in environmental monitoring, using a sophisticated computer controlled system. The operations involved in environmental monitoring are described and the equipment employed is detailed. It is anticipated that the monitoring system employed at West Cliff Colliery will be expanded to allow total and instantaneous monitoring of roadway environmental Conditions.

Jan 1, 1983

By C Rizos, A Ng

Land surface deformation can be caused by underground mining activities. The maximum subsidence normally occurs directly above the location of the excavation of the coal seam. In the case where the longwall mining technique is applied, the magnitude and shape of the subsidence bowl are constrained by the longwall structure (pillar). This paper describes the use of satellite radar interferometry for monitoring surface subsidence due to underground mining, as a cost-effective geodetic technique and complementary to conventional ground surveying techniques. This paper uses data acquired by the current generation of SAR satellites û the European ENVISAT and the Japanese ALOS û to monitor ground subsidence in the southern highland coalfield in New South Wales, Australia. An accumulated DInSAR subsidence mine map is produced using six successive ALOS acquisitions. The results are post-analysed with the aid of geographic information systems (GIS) and validated using ground survey data.

Jan 1, 2008

By Linying W

Entropy is an important concept both in natural and social sciences.Considering the preparatory process of the earthquakes as an open system, in view of basic ideas of the Theory of the Dissipative Structure, the seis-mological Entropy is introduced as an order parame-ter, describing the scale of order associated with the earthquake distribution in time, space and mag-nitude. The features of evolution of seismic acti-vities before and after the large earthquakes have been studied by using the seismological entropy.The preliminary results show that the seismological entropy in certain region decreases as the large earthquake is approaching, it means that the distri-bution of earthquakes has turned gradually in order from disorder.It is expectation that the application of the Principle of Entropy in seismological research will deepen the understanding of the physical process of earthquake preparation. Meanwhile, it will also offer some enlightements in studying mitigation of seismic hazard as well as earthquake prediction.

Jan 1, 1990

By S Choy

Aquatic macroinvertebrates have been used as a monitoring tool for many years. They are ubiquitous and occupy a central role in the ecology of rivers. They are a key link in the aquatic food chain, forming a pathway between primary producers (such as algae and macrophytes) and predators (such as fish, platypus and birds), and some are sensitive to flow conditions, water quality and habitat condition. They are not very mobile and are good indicators of local impacts. As most aquatic macroinvertebrates are benthic, they are better able to integrate effects of changes in water quality, and habitat condition and structure. Their diversity is crucial to the maintenance of a balanced, functioning and healthy river ecosystem. Thus, data on benthic macroinvertebrate community structures can be used for predicting potential impact, assessing the extent of damage and for gauging recovery from damage. Over the past eight years, State agencies throughout Australia, through the National River Health Program have developed models (AusRivAS) to assess river health using macroinvertebrate communities. The Queensland Department of Natural Resources and Mines has sampled both macroinvertebrates and water quality throughout Queensland, including areas affected by mine discharges. This paper will assess results obtained from sampling in the Mt Morgan area to illustrate the usefulness of this method of river health assessment.

Jan 1, 2003

By D E. Langberg, J S. J va, D R. Swinbourne

Specifications on the types and levels of impurities tolerable in metals are becoming increasingly stringent, and are pushing the limits achievable with conventional refining technologies. Particularly difficult is the removal of electrochemically noble elements with low volatilities, such as copper, from more active host metals such as lead, iron and aluminium. Electrochemical refining, utilising the ability of certain solid electrolytes to selectively transport copper or other impurity cations away from the molten host metal into a separate refining phase, may provide an answer to this problem. Numerous studies on solid electrolytes used in concentration sensors have been reported, as well as a limited number on metal refining. Oxygen anion conducting solid electrolytes have been applied to the deoxidation of copper and steel while cation conductors, eg ¯ -alumina and Nasicon materials, have been used to remove lithium and sodium from aluminium. However, solid electrolytes have yet to be applied to the removal of noble elements. The behaviour of solid electrolytes under the extreme conditions of molten metal refining is not well understood. This paper will examine the potential use of solid electrolytes to remove noble metals such as copper from active host metals such as iron. The suitability, and selection criteria of available solid electrolytes for implementation in the metal refining industry in the future will be discussed. In particular, the stability of Cusicon, a copper superionic conductor potentially suitable for use in metal refining, has been assessed and the results of the experiments are presented.

Jan 1, 2000

The Indonesian province of Papua is a remote jungle-clad region covering the western half of the mountainous island of New Guinea. Despite being relatively under-explored to this day,Papua is home to the greatest mineral success story of the 20th century. The Grasberg/Ertsberg minerals district atop the central dividing range contains the worldÆs largest reserve of both copper and gold (Freeport-McMoRan Copper and Gold, 2002). With large mines at Ok Tedi,Por gera and Lihir,and many well-delineated resources such as Frieda River,Wafi and Hidden Valley, neighbouring Papua New Guinea,the eastern half of New Guinea has enjoyed sustained exploration campaigns for gold and copper since the mid 1960s. The combined Grasberg and PNG exploration successes can be measured in terms of ounces of gold produced over the last decade versus available landmass,conf irming the island of New Guinea and surrounding islands as a world-class destination for gold explorers. Yet despite this obvious regional prospectivity and the profitability of the Grasberg operation, a sustained exploration effort in the Papua province in Indonesia has not been achieved. Periodic political constraints, poor infrastructure, high costs, operational challenges, social and environmental concerns and lack of immediate exploration success often impact exploration investment decisions. Accordingly a lesser number of mineral occurrences have been documented in Papua compared to those seen along tectonic strike in geologically similar Papua New Guinea.

Jan 1, 2004

By Tomlinson R. C

There are two main aspects of coal preparation to which the operational Research Executive of the National Coal Board has applied computer models. The first is in the planning of preparation plants and the first part of this paper discusses Simprep, a computer package that was designed to help on these calculations. The other is the development of control schemes to improve quality control, and the second part of the paper deals with the development of simulation techniques for this purpose.

Jan 1, 1977

By J Vann, S Jackson, O Bertoli

Ordinary kriging and non-linear geostatistical estimators are now well accepted methods in mining grade control and mine resource estimation. Kriging is also a necessary step in the most commonly used methods of conditional simulation used in the mining industry. In both kriging and conditional simulation, the search volume or ækriging neighbourhoodÆ is defined by the user. The definition of this search can have a very significant impact on the outcome of the kriging estimate or the quality of the conditioning of a simulation. In particular, a neighbourhood that is too restrictive can result in serious conditional biases. The methodology for quantitatively assessing the suitability of a kriging neighbourhood involves some simple tests (which we call æQuantified Kriging Neighbourhood AnalysisÆ or QKNA) that are well established in the geostatistical literature. The authors argue that QKNA is a mandatory step in setting up any kriging estimate, including one used for conditioning a simulation. Kriging is commonly described as a æminimum variance estimatorÆ but this is only true when the neighbourhood is properly defined. Arbitrary decisions about searches are highly risky, because the kriging weights are directly related to the variogram model, data geometry and block/sample support involved in the kriging. The criteria to look at when evaluating a particular kriging neighbourhood are the following: the slope of the regression of the ætrueÆ block grade on the æestimatedÆ block grade; the weight of the mean for a simple kriging; the distribution of kriging weights themselves (including the proportion of negative weights); and the kriging variance. Outside of the technical geostatistical literature, there is little in the published domain to describe the nature of QKNA and no practical presentation of case examples. In this paper we attempt to redress this by setting out the calculations required for QKNA and defining some approaches to interpreting the results. Several practical worked mining case examples are also given. Finally some comments are made on using the results of QKNA to assist with block size selection, choice of discretisation and mineral resource classification decisions.

Jan 1, 2003

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

The Sto Tomas II orebody of Philex Mining Corporation is a porphyry copper deposit located at Padcal, Tuba, Benguet, Philippines. It was mined through open pit method for the first two years starting 1958 and subsequently through underground method using the Block Cave System. The slusher type of draw was employed at the upper levels of the orebody from mid-year of 1959 up to 1994 and then shifted to LHD as the ore became more competent at the lower levels. Application of rock mechanics played a vital role during the conceptualisation of the LHD method of draw, the first of its kind in the Philippines. Rock mechanics is a combined responsibility of the geology and the mine engineering staffs, with the geology providing the vital information to the mine engineering to include in the mine planning the following:the general geology of the orebody; the ground characterisation through rockmass classification; determination of the cavability of the ore column (this includes our experience on airblasts which occurred during the early stage of our last slusher blocks); undercutting sequence; fragmentation of the rockmass in the ore column; drawzone spacing; proper draw control procedure; lay-out of openings; and the design of ground supports based on the rockmass condition. For the proper interpretation of the rockmass that would cater to the diverse mining situations, Philex adopted the modified geomechanics rockmass classification (Mining Rockmass Rating, MRMR) as this system is recognised and used by most of the block cave mine worldwide. This paper aims to discuss and present the role of rock mechanics in the analysis and determination of geomechanical issues encountered in Philex mechanised block cave operation.

Jan 1, 2000

By Jifan X, Yongyu W, Liangjing L

Shallow interception of groundwater is a special dewa- tering form in the specific geological and hydrogeological conditions. It has an economic and technical effect. The roof of the Fankou Lead-zinc deposit is the Hutianqun aquifer made up of the limestone of the upper Carboniferous system. - A "water-bearing basin" is surrounded by the aquifuge and the aquitard below ¦0 m level at the Shiling Hill section in the Hutianqun aquifer. Based on the natural conditions, an interception gallery is excavated at -40 m level out of "the water- bearing basin", the other gallery excavated at ¦0 m level in the poor water-bearing zone of the Jinxing Hill. During 20 years of experience, the better interception effects have been gained.

Jan 1, 1988

By Baafi EY

Open cut mining in Australia is facing the greatest challenge in its history in attempting to compete not only with other operations internationally, but also with underground operations domestically. Most flat dip and shallow depth surface-mineable coal reserves have been depleted during the last two decades and new open cut operations must extract deeper coal deposits. As open cut coal mines move into deeper areas and the stripping ratios increase, the relative cost of overburden removal also increases. It therefore becomes even more important to design the mine around the optimum overburden removal scheme. The deeper mines are usually multi-seam operations with a more complex geology and with more geotechnical and hydrological problems. Deeper mines are subjected to greater problems requiring more detailed mine planning and design, such as selection of the optimum mining method and pit layout. In planning and design of such operations, the number of alternative methods which need to be considered is consequently greater.Dragline productivity and its stripping capabilities are directly affected by the selection of digging method, strip layout and pit geometry. Every mine has a unique combination of geological conditions. The operating methods that work well at one mine may not necessarily work at another site. Selection of an optimal stripping method, strip layout and pit geometry for a given dragline must be considered with respect to the geological conditions of the mine. With increasing geological complexity of Australian strip mines, it is becoming more important to use sophisticated techniques such as computerised mine planning methods to assist in optimising dragline operations.

Jan 1, 1998

In preparation of this Paper, the emphasis has been laid on the commercial rather than on the technical and scientific aspects of coal evaluation. It is intended to describe and comment on the principal factors which currently determine the selection and procurement of coking coal for the steel industry, and is not based on the results of any original research by the author. Evaluation of different coals for strictly thermal uses, for gas production or other chemical applications has not been attempted, and comparisons of coal with other fuels have been excluded: the paper is concerned only with coals for the production of blast furnace coke. The discussion is strongly related to, and illustrated by, British, and to some extent, other Western European practice, but it is hoped that the general conclusions may have a wider application.

Jan 1, 1975

A modular computer-based monitoring system for mines is dis-cussed. The system consists of the following modules : production moni-toring system HADES, methane monitoring system CMC, seismoacoustic and seismometric systems SAK and SYLOK, communication systems. The system enables one to compose flexible,` economic structures according to the specification of a mine. Application of microcomputer-based monitoring and control systems in coal preparation plants also is discussed.

Jan 1, 1985

By J Tibbett, F T. Suorineni, B Hebblewhite

Block caving is an important mining method for the future economic exploitation of large, low-grade, steeply dipping orebodies. While block caving is not a new method, there are still many unknowns surrounding the mechanics driving the process, particularly as we are forced into deeper, higher-stressed and stronger ore deposits. The caving industry is desperate to provide some explanation behind the myths of caving geomechanics to better predict and manage current caves and caves of the future. Large amounts of data are collected to help understand caving, but it is not fully utilised and current approaches for analysing the data are capacity limited. The application of virtual reality and scientific visualisation (VRSV) technology to visualise and analyse block caving is a critical future component in the assessment toolbox. VRSV enables large, complex, multidimensional data sets to be analysed and the power of human visual problem solving processes to be utilised. Block caving is a complex system and needs to be analysed as a system, rather than looking at individual factors one at a time. A software module has been developed at UNSW Australia for use in the advanced visualisation interactive environment for analysis of the block cave mining system (BCMS). This fully immersive, 3D virtual assessment tool shows exciting potential and is used to analyse the BCMS with a close linkage to time (ie the chronological occurrence of data). This tool will enable a true investigation into the cause and effect relations within the BCMS. Current research is investigating Newcrest Mining Limited’s Ridgeway Deeps operation and is aiming to turn some of the cause/effect relationships into increased geomechanics understanding to provide improvements to ground control management. This paper outlines the methods of assessment used to analyse BCMS geomechanics with VRSV and shows the potential of the software module for BCMS analysis.CITATION:Tibbett, J, Suorineni, F T and Hebblewhite, B, 2014. The application of virtual reality technology and scientific visualisation to the understanding of block cave mining systems, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 195–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

A practical approach has been developed for the design of both grates and pulp lifters. It is based on: an appreciation of the process interaction between grates and pulp lifters, an interpretation of mill charge structure as it relates to discharge through grates, and an analysis of pulp and solids flow in pulp lifter channels. This approach can be used to improve the overall discharge effectiveness of AG and SAG mills.

Jan 1, 2000

By L Edwards, M Haest, D Mittrup

The focus in the iron ore industry has shifted from increasing production volumes with less regard for cost, to efficient production of quality tonnes. BHP Billiton iron ore geoscience and exploration has embedded infrared spectroscopic sensing of drill hole samples to help meet this challenge.Infrared spectroscopy is delivering mineral predictions that are used for (automated) geology logging and modelling. The spectra are processed together with other available data sets to predict geometallurgical and geotechnical variables that include lump per cent and uniaxial compressive strength.Trials are ongoing to test the benefit of infrared spectroscopy during mining, including the analysis of grade control samples and remote sensing of mine faces. Results show great benefits in the fields of short-term geology modelling, better understanding of material (handling) properties, identification of geotechnical risk areas and high resolution ore-waste delineation.These trials are bringing BHP Billiton iron ore closer to its ultimate goal of having infrared spectroscopic data collected across the mining value chain. Once such data are available everywhere, regression models can be trained at one point (eg iron grade model trained on exploration samples) and be applied elsewhere (eg iron grade predicted on mine faces). Such predictive analytics will enable not only high precision mining, but also provide maximum time to tailor plant design to the ore in the ground, based on learnings from ores processed in other plants. This will improve planning outputs that will eventually increase mining efficiency, processing capability and product quality.CITATION:Haest, M, Mittrup, D and Edwards, L, 2017. Infrared spectroscopy in BHP Billiton iron ore with a focus on in-mine infrared sensing, in Proceedings Iron Ore 2017, pp 549–556 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017