Search Documents

By Peters S. G, Beams S. D

CONCEPTS AND REGIONAL GEOLOGY The Charters Towers region holds many keys to the metallogeny associated with the complex geological development of eastern Australia during the Palaeozoic. Tectonic, magmatic and volcano-sedimentary depositional episodes can be identified and related to the chronological development of batholithic host rocks (Clarke & Paine, 1970; Henderson, 1986; Murray, 1986). Pre-batholithic basement rocks in the north (Charters Towers Metamorphics) consist of a package of amphibolite grade schists interlayered with and intruded by gabbros and diorites (Peters, 1987). To the south (Seventy Mile Range Group) greenschist facies Cambro-Ordovician rocks overly some of the basement. The lower age of this basement is not constrained, parts of it could be as old as Pre-Cambrian. Mid-Ordovician (approx. 470 my) to Lower Devonian (approx. 400 my) age I-Type granitoid plutons of the composite Ravenswood batholith intrude the pre-batholith basement and the Seventy Mile Range Group. Igneous activity was initiated again in the Carboniferous with the extrusion of rhyolitic lavas and pyroclastics associated with porphyry and high-level intrusive complexes (Wyatt et al., 1971). The Ravenswood block is bounded by Devonian and Tertiary sedimentary sequences of mainly continental provenence.

Jan 1, 1989

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981

Separation of Nickel and Cobalt from Manganese, Magnesium and Calcium by Synergistic Solvent Extraction - From Batch Tests to Pilot Plant Operation The synergistic solvent extraction system consisting of Versatic 10/LIX63/TBP was used for the separation and purification of nickel and cobalt from synthetic laterite leach solution after iron removal. Very encouraging results were obtained for separating nickel and cobalt from manganese, magnesium and calcium. In batch tests, the organic composition of the synergistic system was optimised and very large synergistic shifts for nickel and cobalt were observed. The ?pH50(Mn-Co) and ?pH50(Mn-Ni) values were as large as 1.65 and 2.40, respectively. The extraction and stripping kinetics of nickel and cobalt was fast. Semi continuous extraction tests were conducted with a pH profile of 5.5/6.1/6.5 in three stages at 40¦C. The nickel and cobalt extractions reached 99.9 per cent with only 5 mg/L Ni and <1 mg/L Co left in the raffinate. With two stages of scrubbing, only 2 mg/L Mn and less than 1 mg/L Mg and Ca were left in the scrubbed organic solution. With two stripping stages, the stripping efficiencies of Ni and Co reached over 95 per cent. A fully continuous pilot plant operation was conducted successfully for 280 hours. With an O/A ratio of about 2 and a pH profile of 5.5/5.8/6.0/6.3 for the four stages EX1/EX2/Ex3/EX4, both nickel and cobalt were almost completely extracted. Using a pH profile of 5.4/5.0 for SC1/SC2, the manganese scrubbing efficiency was over 96 per cent. Using three strip stages, over 98 per cent Ni and 99 per cent Co were stripped with only 64 mg/L Ni in the stripped organic solution. The nickel concentration in the loaded strip liquor reached 83 g/L, resulting in a ?Ni of over 28 g/L. The chemical stability of the system was also assessed over 12 weeks under proposed industrial operating conditions. Operation exclusively under strip conditions at 50¦C and 40¦C resulted in LIX63 oxime half lives of 1.1 and 2.1 years, respectively. Operation exclusively under extract conditions at 50¦C and 40¦C resulted in oxime half lives of 0.26 and 0.82 years, respectively. Losses of Versatic 10 were less than four per cent.

Sep 13, 2010

Gas dynamic phenomena, particularly instantaneous outbursts of coal and gas are problems experienced in gassy, highly stressed coal, both usually the result of depth. Diff- erent mining geometries present different opportunities for seam gas to escape, starting from the virgin condition unaffected by mining and ending with the mining of the coal. The mining of the coal varies from entering a virgin seam cross-measure, heading out into virgin seam, advancing longwall faces into virgin seam and extracting developed blocks from large longwall retreating blocks to small pillars. Each method has its particular gass- iness patterns and particular stress patterns, both changing to some extent with time, and changing as mining progresses. Geological structural anomalies are the cause of gas and stress anomalies, causing in turn greater gas and stress manifestations. Pre-drainage of gas from the working seam not only degasifies the coal but causes it to shrink and so may affect stress as well as gas patterns. Unfortunately prior degasification is not all benefit, and there are some d13- advantages to its use. Also although it is possible to degasify places ahead, gassiness will return if drainage holes are shut down or sealed up and other deleterious aspects may be induced. Research should continue into the problem of instantaneous outbursts of coal and Gas.

Jan 1, 1986

A review of ground control procedures in Western Australian underground mines is presented. Geotechnical input into initial mine design and methods of ground control is rare. As a result, the frequency of unexpected rockfalls is comparatively high, with over three quarters of the mines adopting non-specialist ground control designs experiencing unexpected falls-of-ground. In contrast, mines that provide some level of specialist input into initial ground control design experience decreased rockfall frequencies.

Jan 1, 1992

While there is reasonable agreement on the basic chemistry of the slag fuming process, there has been an on-going debate for nearly 50 years as to the nature of the rate controlling factors in its industrial application. There have been advocates in the technical literature for thermodynamic limitations on the one hand or kinetic limitations on the other. The different viewpoints result in very different predictions as to the technical and commercial potential of the process. A resolution of the debate becomes of importance as pyrometallurgical processes are advocated as a means of extracting environmentally deleterious elements from metallurgical wastes. The present paper reviews the arguments in favour of both equilibrium and kinetic control and puts forward the view that much of the evidence for limitation of the process by kinetic factors under all conditions is unconvincing. It is maintained that the process can approach thermodynamic equilibrium under industrial conditions and that this determines the ultimate limitation on its technical performance. It is acknowledged, however, that kinetic considerations may cause the batch process to fall well short of performance predicted on thermodynamic grounds. The strong process limitation arising from the influence of chemical thermodynamics on the likely outcome of a hypothetical continuous fuming process is contrasted with optimistic forecasts resulting from the extrapolation of process models based only on kinetic considerations.

Jan 1, 2000

By Li YQ, Yoon RH

The photoresponse of natural mineral pyrite and galena electrodes has been studied in aqueous solutions on freshly fractured surfaces (some fractured in situ) using moderate overvoltages. When fractured in situ, the electrode potential of both minerals instantly drops several tenths of a volt. Pyrite exhibits a spontaneous anodic photocurrent at fracture, which indicates upward band bending (depletion layer) on the n-type electrodes. The negative surface charge responsible for the depletion layer is believed to arise from a surface state that is intrinsic to pyrite surfaces, possibly modified by hydroxide ion adsorption. The flat band potential, Vty, of pyrite is at approximately -1.0 V (SCE) at pH 9.2 but to reach V(b, pyrite has to be cathodically decomposed. In contrast, galena assumes the flat band potential at fracture. Subsequent polarisation of galena at potentials positive of Vth produces an anodic photocurrent (upward band bending) and polarisation negative of Vro a cathodic photocurrent. Most of the galena electrodes studied were degenerate n-type and at potentials negative of Vtb, no cathodic photocurrents are observed, indicating the bands cannot be bent downward, consistent with the Fermi level at the surface merging with the conduction band edge near Vn,. Several were close to intrinsic, with the photocurrent changing sign near Vn,.

Jan 1, 1993

Frothing in Seawater Flotation Systems

Sep 13, 2010

By Nightingale RJ

A column (50 cm 4) provided with a bell charging mechanism and a rectangular perspex insert was used to investigate the inter-relationship between charging pattern, size analysis and velocity profile for a number of charging methods. It is shown that a strong correspondence exists between size distribution and velocity profile for bell charged ore and coke and that decreased coke volumes cause higher pressure drops and increased central flow in beds with "V" shaped layers. It is also shown that a bell charged mixed burden exhibits greater segregation than when it is bell charged as layers and that when uniformly charged the mixed burden shows least segregation and a virtually flat velocity profile. A relationship is derived for "V" profile charges showing the extent of central segregation with furnace size.

Jan 1, 1975

Whilst much has been written in past years by geologists, scientists, mining engineers, etc., regarding the well·known and justly notorious anticlinal, or, as they are more commonly known, " saddle" reefs of Bendigo, comparatively little noticehas been given to the synclinal or "inverted saddle "reefs and their relationship with each other. In taking up the question of the synclinal folds, I recognise that it is a large undertaking to confine within the limits of a short paper, and at the same time convey a comprehensive idea of their characteristics, and the importance of their relationship with the anticlinal folds, in the general question of practical mining. However, from a practical point of view I consider the question of great importance, and if an interest in it can be awakened, more particularly among practical men, the object of this paper will be achieved.Before entering into the subject I must briefly state some facts, and perhaps some theories, in respect to the deposition of the Lower Silurian rocks, and their subsequent buckling up, as now seen on the Bendigo gold-field. At the same time, I do not intend to go very closely into the geological aspect of the question, as I wish the paper to be considered as a practical one.

Jan 1, 1902

By C A Heinrich, Morse M. P, Cruickshank B. I, Pyke J. G, Whitaker A

Very little public domain information is available on the exploration signature of the Coronation Hill Au+Pd+Pt deposit. From 1987 to 1990 the BMR (now AGSO) carried out geological, geophysical and geochemical (whole-rock, stream, soil and rock chip) surveys within the South Alligator and Kakadu Conservation Zones and defined several key parameters useful for exploration programs. The essential geological ingredients for the style of Coronation Hill Au+Pd+Pt¦U deposit are oxidised, low pH fluids, dilatant fault structures, a thick neutral to oxidised cover sequence and chemical traps in the basement. In geophysical data, the areas surrounding the mineralisation can be detected by airborne magnetics as major lows in magnetite-rich rocks, whereas in airborne gamma-ray spectrometry data, imaged spectrometric channel ratios such as U2/I'h and U2/K highlighted alteration surrounding the deposits. Three types of stream-sediment and soil samples were taken from each site: (1) -1 mm mesh, 5 kg sample for bulk cyanide leach (BCL) analysis for Au, Pd, and Pt; (2) 1 kg sample of -1 mm mesh sediment for fire assay/ICPMS analysis for Au, Pt and Pd; and (3) 50 g - 180¦ mesh sample for a variety of trace element analyses, including Au, Pd and Pt. Techniques 2 and 3 gave similar results for Au, Pt and Pd, while the recovery rates for Pd and Pt from the BCL samples were considerably lower. Other trace elements did not define unique indicators for Pt or Pd mineralisation, as each sample reflected the dominant lithology in the drainage basin. Rock chip surveys were useful in determining which faults were associated with the ore fluid in regions of multiple fracturing. Results from these exploration-style surveys also confirmed that the Coronation Hill deposit is a variant of the unconformity-style of mineralisation, as all significant geochemical and/or geophysical results occur at or below the unconformity.

Jan 1, 1994

By Cunningham DA

Plant based on the New Jersey refluxing process has been installed at the Cockle Creek Works of Sulphide Corporation Pty. Limited to refine portion of the zinc output from the Imperial Smelting Furnace. Refining of impure zinc is effected by distillation in two stages in vertical columns compris- ing a series of superimposed silicon carbide trays designed such that ascending zinc vapours and descending liquid metal are in intimate contact. In the first stage the volatile elements (zinc and cadmium) are distilled from impure metal, condensed, and while still molten, fed to the second column in which zinc is boiled under controlled refluxing conditions to remove the cadmium content. The resultant zinc has a purity in excess of 99,995 per cent zinc. The availability of refined zinc has made possible the production of a number of zinc alloys for marketing in addition to the basis grades of zinc.

Jan 1, 1969

During the past 18 months several import- ant hydrocarbon discoveries have been made in the Dampier Sub-basin, which is a sedimentary area lying entirely offshore from the Precambrian Pilbara Block in the southern part of 'he Northwest Shelf of Western Australia. This sub-basin is a major sedimentary downwarp forming a northern extension to the Carnarvon Basin. This extension is bounded to the north by the De Grey Nose, separating it from the Beagle Sub-basin. To the south the Dampier Sub-basin merges with the Barrow Sub- basin. Extensive seismic data combined with results from exploration drilling show that the Dampier Sub-basin is a complex depositional basin containing over 20,000 feet of sediments which are mainly Triassic to Recent in age. Tectonically the sub-basin can be divided into seven main structural elements. In a northwest to southeast direction these are the Rankin Platform, the Kendrew Trough, the Madeleine- Dampier Trend, the Lewis Trough, the Legendre- Rosemary Trend, the Enderby Fault Zone and the broad Pilbara Shelf. Permian sediments were encountered in only one well drilled to date in the sub-basin, but Triassic and younger sediments are extensive. The section consists initially of 'hi -_D 7 ri ,~ ~, , i , Derived

Jan 1, 1973

By Van Rensburg C S J

The options that are open to engineers for cooling mines are limited and are primarily dependent upon the thermophysical properties of coolants. These properties are carefully analysed in the context of cooling mines and a comparison is drawn among Ammonia (R717), Monochlorodifluoromethane' (R22), Dichlorodifluoromethane (R12) and Water (R718). From this comparison the extent of Ammonia's superiority as refrigerant is Evident.

Jan 1, 1988

Integrated chemical thermodynamic software and computerised databank systems have evolved over the last 15 years. The extent to which these systems have automated thermodynamic calculations relevant to extractive metallurgy is examined. The scope for further automation and the role of the expert consultant is discussed.

Jan 1, 1991

The Australian industrial relations system is in a state of constant change. We are undergoing a transformation from a compulsory arbitration and an award based system to one which is fundamentally rooted in the concepts of enterprise bargaining. This is true both at the State and Federal level. The structural changes which facilitate the movement away from the predominance of Awards to enterprise agreements has been fostered by both sides of the political spectrum and is a cornerstone of their respective industrial relations platforms.In determining what form or combination of forms of industrial instrument(s) should apply to the individual enterprise, employers must have regard to the viability and sustainability of each form in the changing industrial climate. In particular employers should have regard to the needs and agendas of their employees and unions which may purport to represent Them.

Jan 1, 1998

The re-development of the Mount Charlotte gold mine in Kalgoorlie was carried out piece- meal as funds became available. Optimisation of productivity to offset the high risk which is a function of an indefinite gold price, has been the principal objective of the management.

Jan 1, 1980

By Brown K, Francis D

The Yallourn Open Cut Mine has recently commenced mining operations in the new East Field which will supply the 1450MW Yallourn W Power Station for the rest of its 30 year design life. The authors describe the design and implementation process followed during the rehabilitation of the areas disturbed by works associated with mining in the East Field. One area of the East Field, the old external overburden dump, has been of particular interest and is discussed in detail. A discussion on the fire protection considerations is included as these are critical and often misunderstood as being contrary to good rehabilitation design practice. Finally, the development of a master plan for the rehabilitation of the Yallourn Open Cut in general, incorporating the East Field work, is discussed.

Jan 1, 1992

By C Li, S Wang, L Qiao

Jinchuan nickel mine is the largest nickel mine in China. Cut-and-fill mining method with high density cementing materials is used in the mine. The original mining design divided the mining operation into two steps. The first step stopped the mining rooms and the second step stopped the pillars. Because the two-step method made big trouble for finally mining pillars and strongly limited the mining speed and production, it was successfully changed to a continuous cut-and-fill method without pillars. However, the mining operation in the mine has been down to 800 m and the mining condition is getting worse and more complicated. Through systemetical field investigations and 3D FEM analysis, it is proved that the mining method without pillars is feasible for mining deeper orebodies in Jinchuan nickel mine.

Jan 1, 2000

Recovery of Pentlandite and Chalcopyrite from Tailings by Bi-Cyclone Powerful Flotation Column

Sep 13, 2010