Search Documents

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100 per cent recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after 12 years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By Bhattacharyya A. K

The current methods for predicting pillar strengths are reviewed. A two-dimensional model, based on the Mohr-Coulomb failure criterion, is proposed for determining the compressive strength across the width of a long pillar. The model can be used to determine pillar strength and the depth of the crushed (ie yielding) zone from the pillar edges. The values of the parameters in the model, namely the cohesion and internal friction angle of the coal seam, friction angles at the contact of the coal seam with the roof and floor are determined by matching the strengths predicted by this model with the Bieniawski pillar strength formula for pillar width to height ratios up to 5. It is found that the derived values of these parameters are quite close to the results from laboratory tests. Based on the model, a preliminary analysis of pillar stability is made.

Jan 1, 1995

The southern portion of the Swan Coastal Plain, a geomor-: phological element formed since late'Tertiary times, contains commercially exploitable accumulations of ilmenite, zircon, rutile'and monazite associated with a series'of raised'shorelines. The:location'of the deposits is controlled by a locally outcropping*Archaen-granite/granulite complex and a sea':current pattern'determined'by'local geography and a prevailing wind direction.'-A progression from medium. to high titanium ilmenite is'evident parallelled by. progressive leucoxenisation as the age of the deposits increases. Variation's in trace element content accompany this process. Circulating groundwater has caused vertical mineralogical variations within-individual deposits and' by p'ecipitation of iron has formed layers of hardpan. The economic sig- nificance''of the Geographe--Bay deposits is'briefly discussed,

Jan 1, 1964

The treatment of beach sands in'' the Bunbury/Capel' area for the extraction of ilmenite is a very recent development in the mining industry in'J7estern Australia. Nevertheless since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced. The increasing world recognition of W.A. as a major' Iiroducer of ilmenite is due primarily ' to its low chromic oxide. ; (Cr203 content,, 0,03% to 0.04%, combined with a medium to high grade TiO2 content, 54% - 6 , supported by large reserves, a'. stable government with close access to good shipping facilities.. Ilmenite is produced from-these deposits at low-costs, enabling the industry to compete on world markets despite high rates for sea freights because of the distance from.major markets.

Jan 1, 1964

With the use of 86 rock drills of the jackhammer type at the West Lyell Open Cuts of the Mt. Lyell Mining & Hailway Co., it is of importance to determine the economic as well as the physical life of these machines. With this purpose in mind records have been kept of the footage bored and the cost of new parts placed in each machine, and the following procedure adopted.A graph is plotted for each machine showing the footage bored as a horizontal line and at each 5,000 feet of boring the total cost of new parts noted on this line. (See l"ig. 1.) Thus at a glance it is possible to see... the amount of work done by each machine and the money spent on it in new parts. However, it is difficult to visualise from this graph the increase in the cost of new parts for each machine as its life advances. To obviate this difficulty a curve is plotted with the cost of new parts as the vertical component and the distance bored as the horizontal component. As before the cost of new parts are taken at each 5,000 feet bored. (See Fig. 2.) The curves so obtained are particularly interesting for two reasons:1. Each machine has its characteristic curve.2. The curve always steepens.Some machines are found to have relatively flat curves, others flat curves for approximately 15,000 feet of boring, and others steep gradients from the begining.This demonstrates that it is not always economic to discard a drill after it has been in service for a certain length of time or after it has bored a specified number of feet. Each drill has its own characteristics and so must not be regarded as one of a class, but considered on its own performance.The following use of these curve diagrams has been made to determine whether a machine has reached the end of its economic life. Figure 3 shows...

Jan 1, 1942

By Dharmappa HB, Sivakumar M

This paper is concerned with two case histories of wastewater quality management in underground coal mines in the Illawarra region. The first investigation briefly presents an analysis of mine water discharge having an extremely high concentration of suspended solids and consistently high barium concentrations, averaging, 14.4 mg/I Barium, over the sampling period. A laboratory study of chemical precipitation processes has indicated that about 91% of barium could be removed by using ferric sulphate and lime. On the basis of the information obtained from the environmental audit process an alternative water treatment and reuse system incorporating 51% reduction in the water consumption with 32% less off-site discharge has been suggested (Thomas, 1995).The second case history is concerned with the storm water management at a mine situated in the Illawarra escarpment where only 20% of the wastewater generated in the colliery is discharged off-site. Computer modelling of the storm water system showed that 75% of the clean runoff becomes contaminated through poor management practices and causes the process wastewater treatment system to fail in wet weather. Suggested improvements include relatively simple alteration to the coal wash filtration dams which are expected to reduce the periods of inefficient operation of these dams by 95%. The use of storm water diversion channels and detention basins can reduce the overflow volumes by 70 - 100 % for a ten year ARI (Average Recurrence Interval) storm event (Wingrove 1996).

Jan 1, 1998

By Ritchie IM

The Parker Centre was formally established by the Australian Government's Co-operative Research Centre (CRC) Program in 1992 and is one of over 60 such centres encompassing a wide-range of applied scientific and resource based disciplines. Government funding for the CRC Program is currently around $A140 million per annum and the Parker Centre receives $A1.8 million per annum to support its core research and education activities.

Jan 1, 1997

The McArthur lead-zinc-silver deposit is of the stratiform type. It consists essentially of a mineralized bituminous shale sequence that incorporates tuffites, numerous graded beds, and isolated but massive slump breccia horizons.The principal sulphides are' pyrite, sphalerite, and galena. These occur mostly in the shales. The accompanying turbidites contain only minor mineralization.The geochemistry of the deposit has been investigated in relation to the stratigraphic column and mineralogy of the sediments.A sedimentary origin is proposed for the deposit. Volcanism, thermal spring activity, salinity, regional faulting, and climate are examined as possible factors that may have contributed to sulphide formation and which could be used as criteria for mineral exploration.The metallurgy 'of the McArthur deposit is discussed in terms of its geological history.

Jan 1, 1972

By Zhou Y, Karmis M, Haycocks C

Hazard analysis utilizes interaction mecha- nisms in combination with geologic, structural and mining conditions to delineate areas of potential damage in seams subject to interaction. Using characterizations of conditions peculiar to multi- seam mining, such as innerburden thickness, geol- ogy and structures, initial interaction contour maps can be constructed. Geologic hazard analysis is then carried out on roof, pillar and floor condi- tions in the affected seam using lower seam rock properties and layout geometries in the overlying seam. Either safety factors or damage ratings can then be developed representing degree of hazard in the lower seam. The final hazard map shows both the aerial extent and magnitude of potential dam- age from interaction.

Jan 1, 1992

By Eckersley J, Boyd G

A brief review is presented of the mechanisms and causes of spoil pile failures which have occurred at the Goonyella Mine. In particular, the results of a recent geo- technical investigation of the spoil dumps in the Cleanskin pit are briefly presented. Spoil pile hydrology is discussed in relation to the use of effective stress concepts in the analysis of spoil pile stability. Experience in relation to stabilisation of dragline dumps is discussed as well as the likelihood of current techniques being success- ful in the prevention of gross failures if prestrip material is placed in existing spoil piles. Parameters exerting a major control on dump stability are outlined.

Jan 1, 1981

Developments in mining technology are outlined which point out that longwall face technology has the capacity to produce 20,000t/d on a regular basis. The optimum length of longwall faces is about 250m. Developments of headings and gate roadwyas require radical changes to meet longwall developments. New conceptual models are outlined to meet the challenge.

Jan 1, 1988

By Q Liu

Open stoping is one of the widely adopted methods in underground bulk mining. In this method, fanned or parallel holes are often drilled from a top sill down to a sublevel in the ore zone and blasted ring by ring into a stope for excavation. A mass stope blast may involve blasting rock from multi-level drift rounds and displacing the muck to specific locations in order to allow safe and easy access for ore removal. This paper presents a strategic mass stope blast that took place at a large lead and zinc underground mine in eastern Canada. The blast consisted of more than 800 holes drilled in six blocks from three different sublevels. The challenge lay in the control of ground vibration and muck movement using precise timing to complete the blasting within 6.5 seconds. During this time span, sufficient voids were created in each level to allow the muck to move from the upper to the lower levels in sequential order across the six mining blocks without bridging. This paper describes stope blast simulations using a discrete element computer code for modeling blast-induced rock displacement as well as the application of electronic detonators. These detonators provided the means to accomplish the desired firing sequence including a drop raise blast at the start of the mass blast. The modelling concept is also described in the paper.

Jan 1, 2005

For various reasons, the maintenance of shaft structures is becoming an increasingly important factor in the operation of underground mines. Deterioration mechanisms related to operation of the shaft are identified as corrosion, mechanical damage, fatigue damage and wear. Deterioration mechanisms related to rock movements are identified as vertical strain, ride vertical closure and squeezing. Analytical procedures for assessing this deterioration are discussed, and it is shown how acceptance criteria are developed and implemented. In order to track the deterioration of shaft structures, shaft inspections are undertaken, but the information is often not well documented. Formalised procedures for capturing and recording information, and then processing the information are presented. Finally, two case studies are briefly described to illustrate how these procedures have been implemented in practice, and what benefit has accrued to the mines concerned.

Jan 1, 2005

The chief use of manganese ore is in the production of ferromanganese alloys for steelmaking. Manganese ores generally occur in tropical areas, which influences the type of treatment required. Present methods of treatment are relatively unsophist- icated but demands by customers for tighter specifications will necessitate the installation of gravity concentrator at many mines At present only limited tonnages of minus j in. product can be sold hence future development will centre around methods of producing an agglomerate satisfactory to the smelter.

Jan 1, 1969

Expansion of the B.H.P. Co. Ltd. mater ials handling facilities, at their Newcastle Steelworks, began in 1964 and continued until 1970. The present complex handles the annual iron ore requirement of some three million tons for the Sinter Plant and Blast Furnaces. Iron ore is discharged from ore carriers and conveyed at rates up to 3,000 t.p.h. to either of two 180,000 ton capacity storage yards, where it is blended using boom stackers. Material is reclaimed from these yards at rates up to 1,000 t.p.h. using a slewing boom bucket-wheel reclaimer and fed to a screening station. Oversize material is scalped out and crushed in a closed circuit cone crusher. Undersize material is sized on double-deck vibratory screens which separate at 1/4in (6mm). The two fractions are blended in two of four 70,000 ton capacity blending yards using slewing boom travelling stackers. Bridge-mounted bucket-wheel reclaimers reclaim the blended piles at 1,000 t.p.h. Fine ore is conveyed to the Sinter Plant and lump ore to a second screening station, for rescreening, before passing to the Blast Furnace.

Jan 1, 1972

By J Cahill, D Holden, R Stuart, G Cryan, W Power, W Stratford, S Garwin

The combination of Stage 1 Geoinformatics legacy data intervention processes with the Stage 2 ultra-detailed airborne geophysical prospecting demonstrates a new approach to converting data to information to knowledge, and converting that knowledge into exploration results.   The Coromandel region of the North Island of New Zealand has long been know to host gold deposits of economic viability (Hauraki Gold Fields). To the SE of this area lies the Taupo Volcanic Region (TVR) where the geology and structural setting mirror the Hauraki Gold Fields, however mineral exploration in the past has been hindered by the blanketing volcanic ash deposits. Glass Earth Limited recognised that this whole potential epithermal gold province could be effectively explored utilising rapid, risk orientated processing to review legacy geoscience data: The Geoinformatics Data Intervention Process; which in turn directed ultra detailed airborne geophysical surveys over the TVR. Results have outlined 21 new drillable potential epithermal gold targets; and a plethora of other targets with high prospectivity.

Jan 1, 2005

IF a straight line should be drawn on the map (See 1, page 96) through the northern half of the South Island of New Zealand, from Mt. Domett in the north to Arthur's Pass in the south, and another line drawn parallel to it and at a distance of ten miles to the west, according to the topographic scale, it will be found that within the belt thus drawn across the country all the most important mines, past and present, of the South Island are situated, with the exception of a few in Otago.The most important product of this tract being gold, and Reefton, the most important southern mining field, being situated at about its central portion, the zone may aptly be termed "The Great Reefton Gold Belt." The occurrence of so many gold mines along this particular strip of country is not at all a matter of chance, but is the outcome of cause and effect. Running along the eastern side of the gold belt are the Brunner and Victoria Ranges, which are chiefly composed of crystalline schists and metamorphic granite of probably Cambrian or Silurian age; between these and the gold-bearing series there are interposed at one or two places some beds of slates, limestones, and...

Jan 1, 1910

The magnesite deposits near Young, N.S.W., occur in decomposed serpentine rock below a soil. and alluvial cover. They show considerable variation in both quality and depth which greatly hampers mining operations. Seismic refraction techniques afford methods of conducting detailed and reconnaissance surveys which yield a depth and velocity analysis of the serpentine/magnesite refractor. The measured seismic velocities may be used as an index of the presence and quality of the deposits. The Seismic Timer which was used in the test surveys is a simplified seismograph which makes use of seismic reciprocity by replacing the conventional seismic shotpoints with geophone stations and the conventional geophone stations with impact points of a sledge hammer. Thi,s enables the use of detailed seismic refraction techniques which yield the depth and velocity analysis of the refractor.INTRODUCTIONThe magnesite deposits near Young, N.S.W., were produced by a process of leaching and enrichment of magnesium in serpentine rock. The magnesite occurs in nodular form emplaced in decomposed rock at shallow depths below soil and alluvium. The depth ranges from close to the surface down to some tens of feet. The deposits are patchy and show considerable variation in both quality and depth, giving riseto considerable difficulties in mining operations.Due to the thorough leaching of the surface material, geochemical tests carried out so far have not proved satisfactory for locating the pockets of magnesite enrichment.It was decided to test the application of detailed shallow seismic refraction methods to the investigation of both the depth and quality of the deposits. The tests were carried out...

Jan 1, 1962

By Loo R

The Paper discusses the size and extent of in-pit dust suppression problems created by iron ore mining in the Pilbara region of Western Australia. Dust problems associated with drilling, loading, hauling and tipping are discussed indicating the large quantities of water which can be applied for dust control and attempts that have been made to rationalise this water usage to obtain maximum benefits from the applied water. The magnitude of the problem and the quantities of water involved can be appreciated when one realises that 275 000 tonnes of rock are moved on Mt. Whaleback each day and that there are 40 km of haulroad within the open pit. Initially dust suppression was limited to the spraying of haulroads by large water tankers. Now dust suppression is practiced during drilling and after blasting, wind blown dust is reduced by application, using water cannons,of large quantities of water to floor stocks prior to loading operations as well as by the installation of 16 km of automatically controlled fixed sprinkler reticulation on the main semi-permanent haulroads. The methods used to assess the water requirements for in-pit dust suppression are discussed and the extensive development testing used to evolve the present installations are 1. Environmental Superintendent Mt. Newman Mining Co. Pty. Ltd. Newman, W.A. 2. Chartered Consulting Engineer, Perth, W.A.

Jan 1, 1979

This paper sets out a number of means by which professionals can reduce or eliminate the risk of professional liability whether as directors, employees, partners, independent consultants or contractors. A relationship between client and professional is commonly cited as an example of a fiduciary relationship: the professional "undertakes or agrees to act for or on behalf of or in the interests of' the client "in the exercise of a power or discretion which will affect the interests of that other person in a legal or practical sense."2 As a fiduciary, a professional must ensure that his or her exercise of power does not result in a position of ascendancy or undue influence over the client. Also, a professional must avoid situations where there is scope for even the perception of potential conflict between his or her professional duty to the client and his or her own Interest.

Jan 1, 1995