Search Documents

By Ofori-Ansah K

The zeta potential on the surface of activated orit carbon were estimated in lhe presence of selected cations and anions that are normally associated with gold bearing ores in Kalgoorlie area of Western Australia. Additions of such ions to solution of varying pH shifted the isoelectric point of carbon from pH 4.45 to pH 7-8.3, while the anions moved Lhc isoelectric point 10 less than pH 3.2. In the presence of gold cyanide SoluLion additions of spectator ions indicated the isoelecLric poilll to be aL pH less than 3.2; the only exception was for Fe" ion where the isoelecLric point was at pH 5.9. The decrease in zeta potential appeared to be related to the counter-ions present. The decrease may also be related to the adsorption of hydroxyl ion complexes that are likely to be formed when cations are present in the solutions.Gold adsorpLion by activated orit carbon from gold cyanide solution seem to be indicated by the magnitude of zeta potential on the carbon surface. An attempt is made to relate gold adsorption and zeta potential on carbon surface with the pH of the medium.

Jan 1, 1984

By Jia X

Three-dimensional microscopic modelling techniques involving specific calculations based on direct computation of the Brownian, van der Waals, Born, electrical double layer repulsion, bulk, hydrodynamic and external forces (gravity, magnetic etc) acting on and between each particle in a mineral dispersion are now feasible using advanced computer processor architectures. This contribution surveys the hardware requirements, the advantages and limitations of the approach for enabling prediction of dispersion behaviour a priori. The notion of developing a generic particle simulator, akin to the use of molecular modelling in the area of drug design, based on inputting process-relevant data (solution chemistry, mineral solids properties, hydrodynamics etc) is discussed. The methodology is illustrated with application examples involving: predictions of coagulation of mineral fines; shape and size of magnetically-flocculated hematite; and the kinetics of fouling of membrane surfaces and walls.

Jan 1, 1993

By K H. Esbensen

During the next five years Denmark will implement a significant reduction in the national CO2 emissions to fulfil the Kyoto Protocol. The energy sector is central for achieving this goal and extensive use of renewable energy is the most important single factor contributing to reduce emissions of greenhouse gases. DenmarkÆs renewable energy sources comprise wind energy and biomass. Wood chips and straw are the dominant type of biomass in Denmark. More than 500 000 tons of wood chips are used annually, currently with rapidly growth prospects. This contribution focuses on sampling of wood chips.

Jan 1, 2005

The mathematical modelling of rock fragmentation by blasting is one of the most difficult and challenging problems of applied mathematics. Not only is complex mathematics required but there is incomplete understanding of the basic physics and chemistry involved. The possibility of getting the physical basis of a model correct by simple mathematical and experimental procedures is demonstrated for the novel process of fragmenting rock by high-pressure arc discharges. While the importance of obtaining the correct physical basis for a model is emphasised, high-pressure arc induced fragmentation of rock is shown to be a powerful laboratory tool for the study of blasting.

Jan 1, 1990

By Jacobsen L. K, Gross K. B

This paper, describing milling practice at Mount Isa Mines, is one of a series covering milling methods and costs that is being published by the Bureau of Mines, United States Department of the Interior.The Mount Isa concentrator began operations in May 1931, by treating a mixture of oxidized and sulphide ores. Since March, 1935, only sulphide ores have been milled; this change involved major alterations to the flow sheet. The maximum capacity on mixed oxide and sulphide ores was 2,650 tons per day; the present capacity is approximately 1,880 tons of sulphide ore per day. The installation of additional Grushing, grinding, and flotation equipment when completed early in 1939 will increase the maximum capacity of the concentrator to 2;240 tons of sulphide ore daily.All tonnages in this paper are expressed in tons of 2,000 pounds, gallon measurements in terms of Imperial gallons of 277·41 cubic inches, and costs in dollars at the rate of $4 United States currency to the Australian pound.

Jan 1, 1939

By R B. Turner

The authors have studied and analysed many mineral resource and related projects in Australia. These studies have lead them to conclude that the past performance of many project developers does play a major part in any external financial investment for new or expanding resource based projects. In this paper the authors look particularly at the influence of parties outside the direct control of developers and the effect of' these parties on projects and conclude with a number of points as guidelines for potential project developers.

Jan 1, 1980

By Kidman B. E

The Fitzpatrick area is the deepest section of the North Mine, with the orebody located between 1450 and 1800 m below the surface and some 600 m NE of the main No. 3 Shaft orebody and separated from it by the intensely sheared Globe Vauxhall Shear Zone. Development towards the Fitzpatrick area commenced in 1977 after earlier initial exploration drive development. However, it was not until 1982 that mining in the Fitzpatrick area actually began with the silling out of No. 36 level at a depth of some 1600 in. Since that time mechanised cut and fill mining from an incline ramp system with connecting stope accesses has progressed some 25 m above No. 36 level. Initial sill development on No. 37 level at 1660 m depth also commenced in July 1987 to further develop the Fitzpatrick area.

Jan 1, 1988

The Study of Jamesonite Flotation Behaviour

Sep 13, 2010

Design of underground extraction layouts to protect surface improvements is an important area of subsidence research in the Coal Mining Engineering Branch of the Department of Mineral Resources, New South Wales, Australia. Some conventional partial extraction layout are important with reference to coal recovery and surface subsidence. The analysis ofsubsidence data collected from field surveys over longwall panels in the Southern Coalfield of New South Wales allows assessment of the effect of pillars left unmined between the longwall panels in reducing surface subsidence. The availability ofa wide variety of layouts with ranging degrees of surface movements affords considerable flexibility in designing layouts to suit a particular situation.Total extraction of coal should be the aim as far as possible. Partial extraction layouts should only be considered when surface subsidence movements caused by total extraction are not acceptable to the surface improvements.

Jan 1, 1985

By Gadsden R. W

Physical and chemical requirements are defined for coke and ferrous materials used in modern high productivity blast furnaces operating in Australian conditions. Recent developments in the type of equipment required to be installed at the steelworks to ensure these requirements are described with illustrations from current plant practice provided.

Jan 1, 1976

By S Arthur, J Mills, A R. Penney

A key aspect of seismic management for narrow vein stoping of the west zone at the Beaconsfield Gold Mine has been the development of a fully remote extraction method that does not require personnel access to sill drives within the orebody once stoping commences. Initially, sill driving within the reef is undertaken in a conventional fashion under geological control. Sill drives are developed at a vertical backs-to-floor height ranging from 7 - 12 m. This mining stage includes all activities prior to the commencement of stoping, after which no personnel enter the unstoped section of the sill drive at any time for any purpose. The key aspect of the remote mining cycle is the use of footwall drill drives paralleling the ore drive at a minimum separation of 6 m under survey control. These drives provide the platform for fan drilling of the orebody. Up to 20 m strike panels are blasted in a single shot using electronic blasting techniques. Ore is mucked from the extraction level sill drive using tele-remote loaders. Aerials for tele-remote operation are installed through boreholes from the footwall drive, negating the need for personnel access to the sill drive. Once mucking of a stoping panel is complete, a laser scanning survey instrument is used to survey the final void for subsequent design and production reconciliation purposes. The survey instrument is mounted in the bucket of the tele-remote loader, and is also operated remotely. Finally, tele-remote loaders are used to dump waste rock fill from the upper sill drive. A system of flags and cameras installed in boreholes from the footwall drive assists the operator in locating the live stope edge during the filling cycle, again negating the need for personnel access.

Jan 1, 2008

By Reed M. E, Cloutt B

Particulate samples were taken from the gas space in the settler of the Kalgoorlie nickel smelter using a vertical sampling probe and a specially designed isokinetic sampling probe which also quenched the samples. The vertical sampler was found to give unrepresentative samples. Suction thermocouple measurements of the gas temperature were also made. Using the isokinetic probe samples were taken at four points ranging from near the base of the reaction shaft to the base of the uptake at depths up to 1.5 m into the settler. Dust loadings and the sizing of the samples were determined. These parameters were found to be most affected by sample position and depth. The dust loading decreased along the settler but increased with depth. The loadings varied from zero near the roof to several hundred g Nm 3 near the slag. The dust also became coarser with increasing depth into the settler. Examination of the samples showed them to consist of spherical particles the largest of which were about 500 microns in diameter. The dust was mainly composed of mixed iron/nickel oxides with a little sulphide.

Jan 1, 1991

By Munro P. D

Eh-pH measurements were taken on an industrial zinc reverse flotation process at Brunswick Mining and Smelting Corporation Limited. Laboratory zinc reverse flotation testwork on samples of the feed to the industrial process produced Eh-pH data which were similar to the data from the industrial process.Later, the Eh-pH data from the industrial process were compared with data from a pilot plant scale zinc reverse flotation process at Mount Isa Mines Limited. After comparison with the data from Brunswick Mining and Smelting Corporation, deficiencies in the pilot plant Eh-pH data could be recognised and corrective actions were taken for the pilot plant. A robust pilot plant zinc reverse flotation process was obtained with consistent performance at the expected level.The implications of these findings for a range of processes are also discussed.

Jan 1, 1988

The three systems of mining in use in the Southern Coalfield of New South Wales are bord and pillar with or without subsequent extrac- tion, longwall and shortwall. Bord and pillar with extraction is regarded as the conventional system. The application of continuous miners and powered roof supports (Shortwall) to coal min- ing has, grown in recent years from something of an oddity among extraction systems to an acceptable and viable approach in certain min- ing environments. The method can be applied in a high proportion of situations where normal pillar extraction is practised with advantages over the conventional approach. These advantages extend to both safety and efficiency aspects and also include better utilization of coal reserves. It holds hope for further gain in efficiency because its simplicity of layout lends itself to achieving the goal of contin- uous haulage towards which operators are always striving.

Jan 1, 1976

By Aziz N. I

Examination of the geology and support performance at two site leads to development of an under tanding of the influence of caving on powered support rating. The two site represent the current extremes in support rating, i.e. 6/260 tonne supports operating in the Hirst seam at Solsgirth Colliery, Scotland, and 4/900 tonne supports operating in the Bulli seam, West Cliff Colliery, Australia.A conceptual model considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata.The caving mechanisms identified for the strata of the Hirst and Bulli seams, are different. These mechanisms being related to rock properties - the palaegeography and depositional conditions at each site-produce caved wastes with different yield characteristics.An analysis of the results obtained for convergence and support reaction during production cycles at both sites shows the manner in which support reaction is developed, indicating the importance of higher setting load densities in the Bulli seam.Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations the powered support and the caved waste immediately behind the powered support - further demonstrates the influence of caving mechanisms on support rating.

Jan 1, 1989

By T J. Beardsmore, N Wyche, D Flint, T J. Griffin

Western Australia (WA) is currently the world’s largest iron ore producer, and mining of its huge reserves and resources of iron ore has become a critical part of the state’s economy and regional development. Iron ore exports from WA have reached 760 Mt/a, corresponding to shipping more than one Mt per turn-of-the-tide from the state’s ports. The iron ore sector dominates all commodities produced in WA, and in 2016 accounted for 77 per cent of the state’s royalty receipts, 56 per cent of mineral and petroleum exports (by value) and 50 per cent of mining industry employment. Expenditure on exploration for iron ore (including that for resource estimation and conversion to ore reserves) has declined markedly, from its record peak of $1100 M in 2012 to $280 M in 2016, placing it second after gold. Foreign investment has been a key element underpinning development of the iron ore industry from the 1960s until today, and will likely continue to be so into the future.CITATION:Flint, D, Wyche, N, Beardsmore, T J and Griffin, T J, 2017. The importance of iron ore to Western Australia’s economy, in Proceedings Iron Ore 2017, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

In the geologically prospective nations which rim the Pacific Ocean, mineral deposits offer great potential to create wealth for social and economic development. The paper first examines the geological and economic attributes of potential mineral wealth based on current outlook assessment of all significant base metal deposits discovered to 1988 in two Pacific Rim nations - Australia and Canada. The variability of mineral wealth among the economic deposits evaluated and the major contribution of the few world-class discoveries to total mineral wealth are highlighted. Then, the essential but too often neglected linkage between the makeup of potential wealth and its actual realization is analyzed. The impact of taxation and the role of exploration are crucial in this regard. Finally, the ingredients of exploration success, prerequisites for realizing the mineral wealth of nations, are examined.

Jan 1, 1995

By Swann CA

In order to meet export sales requirements from 1983 onwards, Amcoal developed a new underground mine in the Witbank area of the Transvaal. The mine was required to produce 5 million tons of run of mine coal per annum giving rise to 4 million tons of saleable products. A description of the coal processing plant is given with comments on design philosophy and design parameters. Main features of the coal processing plant are the raw coal handling facilities, centralised control and data capture and the loadout station. The management systems applied during the commissioning period are described. The difficulties experienced and their solutions are discussed. Commissioning was concluded with an independent plant performance test.

Jan 1, 1986

The OK orebody comprises a steep dipping narrow quartz reef averaging 0.4 m in width hosted in basalt and gabbro with porphyry bars cross-cutting through it. The following paper tracks the mining of this orebody, challenges encountered, measures undertaken to address these challenges and changes in mining conditions and methods as the mine matured in both depth and age. The initial mining method was narrow vein hand held shrink stoping accessed by shaft, that over the period of the mines life was superseded by gallery stoping, shrink stoping and ultimately mechanised narrow vein long hole sublevel open stoping. The reasoning behind the change in mining methods is detailed, including safety and cost benefits. The transition presented many challenges that were overcome, resulting in the successful development of a narrow vein long hole stoping method. The lessons learnt during the transition period and the practices and principles developed for successful mining of narrow vein orebodies using long-hole open stoping methods are summarised in this paper. The final section of the paper takes a retrospective view of how the knowledge gained through the mining of the OK orebody would be applied to a new mine containing an orebody of this type, with consideration given to the initial excavation design, equipment selection, mining sequence, geotechnical investigations and mining method used.

Jan 1, 1998

During the last century Allis-Chalmers has supplied many screens of various types to industry, from revolving screens to the large capacity highly efficient screen available today. The features incorporated over these years in horizontal and inclined screens are varied and numerous and include many innovations such as tri-and bi-sloped screen decks. Today the emphasis is on wide vibrating screens with good "G" value, with large "throw", to achieve high capacity. Larger screens lead the way to treating a somewhat neglected area of mining operations - that of concentrator mine flotation tailings to allow effective transportation and stacking by conveyor belt. The benefits from a cost, water saving and environment view point are discussed in this paper.

Jan 1, 1984