Search Documents

By Bisshop J. P W

Maximum recovery of sulphide minerals by flotation is achieved over a limited size range. Valuable particles above and below this range have a smaller probability of being recovered. In the normal grinding-flotation operation, not all valuables are reduced to the optimum size range, and therefore sub- stantial losses occur. A significant improve- ment in the size distribution is not usually possible within the conventional circuit, and a more complex arrangement may be necessary to obtain optimum recovery of the valuable mineral. This problem is considered with refer- ence to the Mt. LyeZl concentrator. The performance of the existing circuit is dis- cussed, and it is shown that losses in recovery occur in both coarse and fine sizes. Laboratory tests indicate that regrinding the coarse particles results in an increase in recovery of up to 4%. Redistribution of plant grinding capacity to reduce initial grinding power by 6% and use this capacity to regrind coarse particles was considered. It is con- cluded that overall plant efficiency would be increased by 2% provided that overloading of the regrind mill could be avoided.

Jan 1, 1977

By Mozley R

Contaminated sediments are a multinational problem. A crucial factor in solving an environmental problem is knowledge of, not only the amounts of polluted soil, the contaminants involved and their concentration, but also the historical background of the problem. Processing polluted soil is a tailor made activity based on rational decisions resulting from a detailed treatability study. Lack of information about characteristic properties of a specific sludge/pollution combination is the main obstacle in the route from first ascertaining that a particular harbour subsoil is polluted, to final identification of the full scale treatment plant. In the first instance, information must be generated regarding the distribution of pollutants in relation to the distribution of the original geophysical components. Based on this information rational decisions can be made on separation at a particular cutpoint and what sequential techniques should be involved for a certain fraction. For this purpose a `fingerprint method' is presented especially developed for investigation of polluted soil and sediments. The heart of the fingerprint method is a series of sequential hydrocyclone separations, by which a series of products is generated. The objective of the fingerprint method is to select an optimised treatment procedure in which the pollutants are concentrated in as small a volume of material as possible, leaving the bulk of the material clean. The pollutants can then readily be destroyed or isolated from the environment. The philosophy and advantages of the fingerprint method are demonstrated for a harbour sludge containing heavy metals as main pollutants. Hydrocyclone separation combined with flotation of both the coarse and fine fraction resulted in reusable and dischargeable products. Flotation of the fraction of fines was carried out by means of an experimental flotation cyclone enabling the selective recovery of mineral particles with diameters less than 10 microns. The overall conclusion is that design and engineering of treatment flow schemes for polluted dredged materials is a tailor made activity based on rational decisions resulting from the fingerprint information.

Jan 1, 1993

Much has been written about leadership over the years. It is probably one of the most written about but least understood and defined concepts in business. Leadership and management are often confused and blurred, and inspirational words such as mentor, coach, motivator and the like, are often interspersed when describing a leader. There are a few things we do know about leadership:The only thing common to all leaders is that they are different.Leadership is not the sole domain of business; it applies to every aspect of human endeavour. We are all required to lead at times, and we all have it in our ability to lead. There is no set of predetermined competencies, which a leader must possess to be effective. Hence there is no course in the world that can teach you to become a leader. There is no such thing as the perfect leader. Leadership is a verb, not a title; you actually have to do it to be judged a leader. All leaders no matter how you define the term, must leave a legacy. Thus in the busy world we all live in, what are the lessons in leadership that we can all learn from, that will assist us all in our pursuit of leadership. The purpose of today is to put forward a framework for leadership that I have been researching and working on for many years. It is not the definitive framework, merely a framework. Out of today you will take your own collective thoughts, learnings, observations, experiences, education and training, and collective wisdom, and apply it to yourself.

Jan 1, 2004

Conventional treatment of oxide and oxidised sulphide minerals by flotation involves the use of sodium sulphide for sulphidisation. Sodium sulphide is generally applied in a "slug" dosing fashion with manual regulation. However, it is recognised that "over addition" or "under addition" of sulphidising reagent can result in poor flotation recoveries. Thus, control of sodium sulphide additions is an important aspect of a sulphidisation circuit, both commercially and metallurgically. In any plant where the flotation feed is "constant" it is possible to operate at a constant rate of addition of sodium sulphide. In actual plant practice, however, it is difficult to maintain a truly constant feed for any reasonable duration because this implies not only a constant feed-rate, but also constant mineral composition and particle size range. These factors can vary significantly and ideally require corresponding variations in the additions of sodium sulphide to maintain optimum recoveries. To cope with variations in the feed, it is essential to have automatic rather than manual regulation of the sulphide reagent addition. The CPS process achieves this control by utilising a sulphide ion-selective electrode as a control instrument in sulphidisation. The CPS process which uses a selective electrode, enables the sulphide ion concentration in the flotation pulp to be monitored and controlled continuously throughout the stage of sulphidisation.

Jan 1, 1989

The problem of comparison of island arc's andesites in terms of petrochemical data is exa- mined. It is definitely established that only two main factors exist controlling the petroche- mical variety of the Kurile arc's andesites.Ori final multivariate statistical technique and computer software are used to extract these fac- tors. It is shown as well that the chemical com- position of igneous rocks depends on the type and structure of the Earth's crust. The follo- ~cing interpretation is proposed for the two factors describing petrochemistry of andesites: the first one is the depth to the Benioff seis- mofocal zone and the second one is supposed to indicate the position of the peripheral magma chambers. The basic trends of variations in the chemical composition components depending on the changes in the controlling factors are de- Tcnnined.

Jan 1, 1987

By Langham B. M

A chemical study of the petrographic components of Greta (Maitland) coal, carried out by the Metropolitan Gas Co. (Melbourne), has revealed an anomaly in the composition of the durain which was thought to warrant petrological investigation.The original study, by the Metropolitan Gas Co., extended over eight shipments of coal received during the winter of 1943.The percentages of the several petrographic components were eslimated by careful handpicking of large samples of each shipment, and analyses were made of the handpicked components, which were also tested as to their gas-making and coking properties.The results are summarised in Tables 1 and 2. At first sight the components of the Greta coal bear a general resemblance in composition to those of other bituminous coals of similar rank, apart from a notable richness in volatiles, which is a distinctive feature of Greta coal. The durain has a typically higher ash content, and lower volatile content than the clarain (Table 1); and the coking behaviour of the four components is typical (Fig. 4).When, however, the analyses of Table 1 are re-calculated on a dry, ash-free basis, an anomaly appears: the clarain and the durain, on this 'pure coal' basis, have practically identical compositions, with the durain containing a slightly higher proportion of volatiles than the clarain (cf. Table 3); but the tar yield of these two components is very different (Table 1). Re-calculated on a dry, ash-free basis, the yield from the clarain is 18.9 gallons of tar per ton, while, that of the durain is 29.0 gallons per ton. The gas derived from the durain is correspondingly richer in illuminants (CH etc) and poorer in hydrogen than that from the clarain (Table 2), and is also notably richer in nitrogen.That the composition of the Greta durain is consistent is proved by the analyses of Table 3, in which the compositions of the respective durains and clarains of eight separate shipments of coal are compared. In most bituminous coals, the durain contains several per cent less volatile matter than the associated clarain, and high volatile content in a durain usually indicates a durain rich in spores.

Jan 1, 1947

By Murray C. G

A database of over 1300 earthquakes has been used to investigate the relationship between seismicity and tectonics in two areas of eastern Queensland and NE New South Wales. These areas have been monitored by several networks that were installed primarily to monitor seismicity associated with the impounding of large reservoirs. Events that occurred prior to the installation of these networks have been excluded from the analysis because they have large uncertainties in location.Seismicity in SE Queensland and NE New South Wales is concentrated in the coastal regions. Activity also extends off the coast of Queensland and beyond the continental shelf. The coastal activity is mainly within the New England Fold Belt. An area of the fold belt overlain by the Clarence-Moreton Basin is also active. There is an area of activity near St. George that correlates to the Wunger Ridge. Fraser Island and the adjacent onshore area, near Maryborough, are notably aseismic.Within the New England Fold Belt there is a NNW trending zone of concentrated activity that includes the South D'Aguilar Block and the Esk Trough as far as Gayndah. The Nambour Basin, the Gympie Province, and the southern portion of the Yarrol Block are significantly less active.Composite focal mechanisms of several groups of accurately located earthquakes in SE Queensland indicate predominantly reverse faulting. This faulting is the result of the crust being compressed horizontally in a NE-SW direction.Activity in the Burdekin Falls Dam area of central eastern Queensland is confined to the Drummond and Bowen Basins. There is also significant activity offshore from Townsville and Bowen.

Jan 1, 1990

Bakelite is fairly widely known as a suitable material for the mounting of ore specimens, concentrates and tailings for microscopical study, but has not as yet had extensive application. It is the most suitable mount for specimens which are to be held in the mechanical holder of a polishing machine, based on that described by J. W. Vanderbilt*, which is installed in the Geological Department of the Melbourne University.Bakelite products are prepared by subjecting bakelite powder to a temperature of about 1600 C. under a pressure of approximately two tons per square inch for a period of four minutes. The shape and size of the products are governed by the use of suitably constructed dies. When the concentrate or tailing is mixed with the bakelite powder, a briquette is produced which can be polished so that the opaque minerals in the sample can be examined microscopically in the same way as in a piece of solid ore. A simple machine for the construction of these briquettes has been described by Head and Slavin. It consists of a small four-pillar press in which the pressure is supplied by...

Jan 1, 1933

By Whincup P

Hilton deposit comprises en-echelon silver-lead-zinc orebodies with reserves in excess of 50 million tonnes. The host rock to the ore is a dolomitic and pyritic shale/siltstone which dips steeply west. The shale/siltstone is deeply leached and porous, particularly over the Ore Zone where the depth of leaching continues down to 440 m below surface, and constitutes an extensive permeable aquifer system containing a large volume of saline acidic groundwater. Initial production commenced at Hilton in 1987 well below the aquifer. A dedicated dewatering and monitoring programme is in place to ensure security of stoping operations and allow extraction of ore close to the leached zone in future years. Dewatering is undertaken from controlled bores from underground sites. Mine groundwater discharge is presently at the rate of 4000 kl/day with plans to increase to 8000 kl/day. An additional 2000 kl/day of fill and service water and water from secondary aquifers is also pumped from the mine daily. Although recharge rate to the aquifer is minimal, studies indicate that due to the size of the aquifer and future extensions to mine development, dewatering will be a life of mine activity. The investigations which have been undertaken to determine optimum dewatering techniques and schedules are described. These include production bore tests, mine planning constraints and computer aquifer modelling. Gravity geophysical techniques have been successful in delineating the lateral and vertical disposition of the aquifer. The mine dewatering schedule, whose principal component is underground mine drainage, is also outlined.

Jan 1, 1988

An on-stream iron ore analyser has been developed in collaborationwith Hamersley Iron Pty. Limited for determining the iron content ofboth lump (- 30+ 6 mm particle size) and fines ( - 6 mm particle size)on conveyor belts. The analyser, which is called IRONSCAN, is basedon pair production, and is now commercially available from Mineral ControllnstrumentationLimited (MC!) in Adelaide. It can be mounted underexisting conveyor belts with minimal modifications to the conveyor structure,and the presence of steel cables in the belt does not interfere oncethe analyser has been correctly calibrated. The analyser has been extensivelytested on both lump and fines on the shiploading conveyor at Dampier,and typically the root mean square (Lm.s.) deviation between singleIRONSCAN measurements and conventional chemical analyses is betterthan 0.5070 Fe. It is currently being evaluated on - 150 mm ore from theprimary crusher at Mount Tom Price, and initial result are encouraging.The principal advantage of IRONSCAN is that it provides rapid informationon ore grades. But perhaps its greatest potential is at the primarycrusher where conventional sampling and analysis is very expensive toimplement.

Jan 1, 1988

By Stewart C. A

The Northparkes copper-gold project is being developed in Central Western New South Wales approximately 30 km NNW of the town of Parkes and approximately 350 km west of Newcastle. The project is a joint venture between North Limited (80 per cent) and the Sumitomo Group (20 per cent). North is the manager. The basis of the project is three copper-gold orebodies, the northern two of which are being mined by conventional open cut methods with the third and largest orebody at the southern end of the lease to be mined by block caving. A fourth mineralised body has been identified in the centre of the lease. While further evaluation of this deposit is required it would appear to be amenable to block caving. Oxide caps of gold ore and copper-gold ore over-lie the two northern orebodies. Development commenced with the construction of a carbon-in-pulp (CIP) plant to treat the oxide gold ore. Construction of a flotation plant to treat oxide copper-gold ore and sulphide copper-gold ore is underway. When full-scale operation is achieved late in 1996 the plant will treat 5.0 million tonnes of ore per year of which 1.1 million tonnes will be open cut ore and 3.9 million tonnes will be block cave ore. In terms of annual ore tonnage the underground mine will be the largest metalliferous mine in New South Wales and the second largest in Australia.

Jan 1, 1995

Technology is playing an increasingly large role in the operations of our mines. There is a temptation to regard the implementation of technological systems as the objective itself when, in reality, systems are used to support a business process. Only when the process succeeds will the systems be seen to succeed. Understanding the distinction between system and process is critical. This understanding, together with the resultant holistic approach, is considered to be critical to successful implementation and operation of Mine Control process. This paper examines the critical factors essential to success in establishing and sustaining a Mine Control process that maximises benefits to an operation. These factors have been developed during the author's experience of nearly 30 years in Mine Control projects across over 50 sites. Each factor is discussed in relation to real world examples at well-known mines.

May 1, 2010

The Sons of Gwalia Mine in Western Australia is situated about 140 miles north from Kalgoorlie in arid country, where supplies of fresh water are difficult to obtain.Mine salt water is used throughout the treatment plant, whilst fresh water for domestic, boiler, and power purposes is pumped from a number of shallow outlying wells. The waters from all wells are constant in character, although they vary in the quantities of salts contained.An average sample of mixed waters gave the following analysis (Gr. per gal.):Sodium chloride 70.82Magnesium chloride 33.03Calcium chloride 26.98Calcium carbonate .. 11.57Calcium sulphate 22.71Iron oxide and alumina 2.10Silica and insoluble 4.58When this water is used in the boilers in its natural state it is scale-forming and intensely corrosive.

Jan 1, 1927

By Gao K, Wu C, Langley J. M, Waugh B, Farrell K

The dissolution of carbon from carbonaceous materials into molten iron is a key step in various ironmaking operations. For example, in new direct smelting processes, carbon in the form of coal is injected into the molten iron bath, which leads to the dissolution of carbon. In foundry operations, typical recarburizer materials can range from high purity graphite to chars. The dissolution performance of these" materials is critical to the operation and could dictate the efficiency and economics of the process.Dissolution kinetics has been studied by various investigators to explain the influence of melt conditions and carbon type (Sahajwalla et al, 1994; Shigeno, Tokuda, and Ohtani, 1985; Orsten and Oeters; 1988; Ganguly and Reid, 1992; Wright and Taylor, 1993). The influence of melt sulphur content on the dissolution kinetics has been characterised (Sahajwalla et al, 1994), with sulphur retarding the rate of carbon dissolution. The carbon dissolution from different sources is seen to vary significantly even under similar melt conditions. This observation has been explained by investigators on the basis of the varying ash content present in the carbonaceous materials. However, ash content alone cannot account for the variability in dissolution kinetics reported in other studies. One such study is presented below.In a recent study (Sahajwalla et al, 1994), pulverised carbonaceous materials were injected into the molten iron bath and the" dissolution kinetics was established. The dissolution of graphite and glassy carbon, which contain almost 100 per cent carbon, was seen to be significantly different when the molten iron contained sulphur. The influence of melt sulphur content was explained on the basis of different wetting behaviour observed.Importantly, the study showed that even pure carbon sources dissolved at significantly different rates. Hence, their performance could not be explained on the basis of ash content.The key difference between graphite and glassy carbon is in their atomic structure. Graphite is highly ordered whereas glassy carbon has relatively poor ordering in its atomic structure. This study showed that the atomic structure in carbonaceous materials can have a significant effect on their dissolution performance.The focus of the present investigation which stems from the past study described above (Sahajwalla et al, 1994), is to investigate the influence of atomic structure of carbonaceous materials on their dissolution into Fe-C-S melts.The specific objective of this study is to determine the relationship between dissolution kinetics and crystallographic character of carbon sources. In order to accomplish this goal, a range of different materials representing a spectrum of carbon sources have been chosen for the investigation. These materials include brown coal char, two types of Auscarb (A and B), and commercial graphite. Auscarb is prepared by calcining Auscoal at 1000°C. Auscoal is made from chemically cleaned Australian coals (Bowling, Chandler and Waugh, 1990). Part 1 of this paper details the dissolution performance of the materials studied, while Part 11 describes the X-ray diffraction study. The relationship between the atomic structural dimension and dissolution rate constant is discussed in light of the results obtained.

Jan 1, 1996

By Edwards A. B

In their description of the post-mine leaching of galena and marmatite at Broken Hill, Messrs. Garretty and Blanchard1 find themselves unable to account satisfactorily for the fact that the more usual order of solubility of these two minerals is here reversed, and that the galena is leached more rapidly than the marmatite. An explanation of this somewhat unusual phenomena is perhaps provided by the recent work of Garrels.2 Garrels showed that the presence of Cl' ions in Pb-Zn solutions, in concentrations in excess of 0·1 N, rendered the zinc less soluble than the lead. It seems possible that Cl' ions may be present in the underground waters of the North Broken Hill Mine in sufficient concentration to cause such reversal in the relative solubility of the lead and zinc sulphides.Thus the analysis of "water believed to be free from contamination by mine drainage" given by Messrs. Garretty and Blanchard (p. 158 of their paper) is as follows:Total solids in solution 878 grains per gallon...164 grams of Cl per gallon is equivalent to 2· 3394 grams of Cl' per litre, which is equivalent to 0066 N.This concentration is approaching a value sufficient to cause a reversal of the relative solubility of zinc and lead salts; and it seems probable that there will be parts of the ore-body where locally the Cl' concentration will greatly exceed this figure. At such points the lead salts would be more soluble than the zinc salts, so that the galena would be leached more rapidly than the marmatite. With the dilution of such Cl'-rich waters with water containing less Cl', the Cl' concentration would fall below 0·1 N, and the lead would be reprecipitated, while the zinc would stay in solution, as, for example, in the water analysis quoted. The other point on which the authors speculate is the reason why the Northern Ore-body in the mine has undergone greater leaching than the...

Jan 1, 1942

The need for a carefully prepared set of special conditions, to be used with general conditions of contract or, alternatively, a purpose written contract for adoption in tunnelling work in Australia is discussed. Recent decisions on the proprietor's liability for tender information and arbitrator's power to award interest are examined. A new clause for inclusion in contracts specifically giving arbitrators power to award interest is suggested. Similarly, a new clause covering delays due to environmental disputes is suggested, particularly for marine outfall tunnels. An alternative method for the settlement of disputes by negotiation is suggested for consideration and contracts and contract administration are discussed as the possible weak point in the construction process. At the conference it is intended to present a method or process to be used in contract administration which should reduce disputes, result in a better quality and efficiency of administration and ultimately in better contracts'.

Jan 1, 1981

By J A. Rumball

Measuring cyanide in the leach liquors associated with high copper and/or sulfide ores is a non-trivial exercise. It is well known that copper complexes with cyanide and reduces the amount of cyanide available for gold leaching. What is not so well known is that the rhodanine end point overestimates the amount of cyanide available for leaching in the presence of copper. Sulfide ions also interfere with a rhodanine end point titration, although this is less of a problem as the black silver sulfide precipitate formed clearly indicates to the operator that something is wrong. Thiosulfate, which forms readily from the alkaline oxidation of sulfides, causes an overestimation of the cyanide available for leaching due to the formation of Ag(S2O3)-. The net result of these observations is that rhodanine is rarely of value as an end point indicator in complex solutions. It generally overestimates the amount of cyanide available, providing plant metallurgists with a false sense of security. Potentiometric titrations are generally much more capable of accurately measuring cyanide in complex solutions. The interfering effect of copper can be resolved and it is even possible to estimate the copper concentration using the inflexions associated with the titration of CN- + Cu(CN)43- versus Cu(CN)32-. Using the potentiometric method sulfide ions can be determined before the cyanide measurement is made due to the formation of AgS2, although the electrode will foul with repeated measurements. Thiosulfate can also be distinguished from cyanide with a potentiometric titration. Rhodanine and potentiometric titrations are both affected by the pH of the liquor. At pH 9.2 half the cyanide will be present as CN- and half as HCN(aq) with only the CN- being titratable. This does not hold in the presence of a buffer active around pH 9. In the presence of sufficient buffer, both the CN- and HCN(aq) are titrated. Ca(OH)+ may buffer the pH when large amounts of lime have been added.

Jan 1, 2007

By Elliot B. J

Flash smelting is a complex and capital intensive technology. Although in use for 50 years the technology is still not well understood from a fundamental point of view and thus uncertainty is evident when significant change to the practice is necessitated. The application of effective design and process simulation tools has significant advantages when process change and improvement is required. Mathematical models have been used to simulate the processes occurring in the shafts of copper flash smelters. The present approach to flash furnace modelling differs from earlier work in that the burners were modelled in detail, the output from the burner model becoming the input to the shaft model. This paper serves as an introduction to the modelling process used to analyse the performance and provide a better understanding of the parameters applicable to the flash furnace at the Kalgoorlie Nickel Smelter.

Jan 1, 1992

By Croggon R

Passing a direct current through a jointed fine grained soft rock mass auses the movement of water by the process of electric-osmosis. There are other processes such as electrolysis which transport ions that interact with associated ions and can, in turn, be oxidised. This results in the dissolution products being transported towards the cathode electrode. In the cathode region the ferrous hydroxide is oxidised to ferric hydroxide %%ith consequent precipitation. The cracks and joints are current pathways, along which the ferric hydroxide is deposited. This deposition reinforces the joints and increases the shear strength. By adding calcium chloride to the anode, the rate of corrosion is increased with the concomitant increase of deposited ferric hydroxide along the joints. This, in turn, significantly increases the joint shear strength. The process is pervasive in that the current via the water paths travels through the crack and joint systems The result is that not only specific joints are reinforced but the cracks and mtciconnected voids are also reinforced.

Jan 1, 1997

By Kubo H, Ninomiya R, Ojiro T, Sato T

New high-strength Zn alloys for moulds are demanded from the automobile and electric industries in Japan, because the s rength of Zn moulds is still not high enough for the mass production. There are two approaches to improve the strength of Zn alloys. One is to increase the Al content. ZA alloys (ZA-8, ZA-12, ZA-27) were developed through this approach. The other is to increase the Cu content. But it is known that an increase in Cu generally depresses the castability of Zn alloys, so that the alloys with increased Cu have been rarely studied until now. In this study a reconciliation between the strengthening and the castability of Zn alloys by enriching both with Al and Cu has been attempted. Accordingly we have studied on the Zn alloys containing 4 to 25 mass per cent Al and to 24 mass per cent Cu have been studied. Their fluidity, which primarily corresponds to the castability of the alloy, were measured first and 19 alloys were selected based upon their fluidities and casting temperatures. Mainly the mechanical properties of all 19 alloys were tested and some were found to be excellent in both strength and castability. Z1009 (Zn-IOAI-9Cu-0.02Mg alloy) cast in a sand mould has the tensile strength of 360 MPa while ZAS (Zn-4AI-3Cu-0.04Mg alloy), which is the most popular alloy for moulds, is 215 MPa. Z2520 (Zn-25AI-20Cu-0.02Mg alloy) cast in a sand mould has a Vickers hardness of 178, compared to 107 for ZAS and 104 for ZA-27 (Zn-27AI-2Cu-0.02Mg). Furthermore the castability of Z1009 is as good as that of ZAS. The underside shrinkage occuring in casting ZA-27 is restrained in Z2520.

Jan 1, 1993