Search Documents

By N McKenzie, F Brodbeck

The North-South Bypass Tunnel is the first project to get underway as part of BrisbaneÆs transport plan, which aims to improve the urban road network. The total length to be excavated is 6.8 km, which includes 4.8 km of driven tunnel and associated road connections. Construction commenced in August 2006 with project completion targeted well before the contractual completion date of October 2010. Due to the local geology, in particular the hard Brisbane tuff and neranleigh-fernvale formation, a combination of tunnel excavation methods are used. The majority of the tunnel is excavated by two tunnel boring machines which have a rate of progress of 16 - 20 m per day in rock having a compressive strength of between 80 and 150 MPa. Ten roadheaders operate at a rate of up to 2 m per day excavating the remaining tunnels, such as ramps, access tunnels, cross passages and merges. The tunnel team are managing the challenges and complexities associated with tunnelling through the hard Brisbane rock. A major challenge arose during the planning of the initial mainline excavation underneath the Royal National Association Showground in Bowen Hills. This section contains low rock cover and historical maps indicate that the showground is located within a former topographic depression (alluvial valley), which a creek once flowed through.Due to traffic merge design requirements, both tunnel boring machine (TBM) and roadheader excavation methods were required to be used in this challenging geological profile. The answer was to stabilise the alluvium above both TBM section tunnels from the surface prior to excavation and to operate the TBM in single shield mode with immediate grouting of annular void from the tail shield. In addition, the roadheader section of tunnel required additional support by spiles and canopy tubes installed from the tunnel face.

Jan 1, 2008

By Will D

This presentation is to outline the current practice of mechanised stoping a one-metre wide, gold bearing ore body to optimise fragmentation, minimise dilution and reduce stoping costs.Coolgardie underground operations have historically been mined using traditional shrink stope methods, but in this recent economic environment (with falling gold prices and high costs of traditional methods) it was necessary to look for alternative methods in order to reduce costs and increase productivity.Although still in a learning and refinement phase, CGNL is satisfied that it is feasible, practical and more economic to use mechanised long up-hole stope and long-hole rising methods to significantly reduce the mining cost, reduce dilution, increase safety and increase productivity three-fold compared to traditional airleg methods used throughout the Fasten Goldfields.

Jan 1, 1993

Modern Management Systems for Higher Margins By Malcolm Roberts, Catalyst for Corporate Performance Ltd Malcolm Roberts put the case for changing systems in order to change behaviours and attitudes and improve productivity. ""The key to lifting margins is changing systems."" A system is anything that drives ways of doing things. Sometimes these are formal, and documented, and sometimes they are not. Improving productivity The way to dramatically improve performance is to use the systems. Roberts stressed that if systems and processes are under control, the benefits of automation are huge. If they are not, the benefit of automation will be lost. To improve productivity, you need to: ò identify what to change in the process, ò use the proven methodology to systematically improve the process, and ò change what people do - change work practices.

Jan 1, 1997

This is a brief introduction of a sewer pipeline constructed with a pipe jacking method in combination with a 1 200 mm finished inner diameter tunnel boring machine developed for the first time in Japan. The pipeline is located under a national highway running through a densely built urban area and is 185.7 m long and 2.9 m to 3.7 m deep from the ground surface. The geological features along the pipeline show mostly slate and partly silt. The pipeline was constructed with a newly developed multi-application type tunnel boring machine equiped with a fluid transport system. The construction consisted of tunneling by a tunnel boring machine followed by pipe jacking operations. The excavated materials were dis- charged off the tunnel by a fluid transport System.

Jan 1, 1987

Thermodynamic properties of the solutions of hydrogen in metals and carbon in austenite were investigated and it is possible to predict the interstitial solubility in these systems over relatively wide ranges of temperature and solute activity. Monte Carlo methods were used to compute the arrangements of interstitial atoms on the tetrahedral sites in body centred cubic metals and the octahedral sites in face centred cubic metals. It was shown that the non-configurational entropies of solution of hydrogen in metals can be interpreted as being principally vibrational and on this basis the potential value of the isotopic solubility ratio theory in indicating the compositional variation of these non-configurational entropies was discussed. The need for future work along these lines is pointed out.

Jan 1, 1970

By Ahmed M, Leung L

A program of microseismic noise monitor ing for gas outbursts, in conjunction with other mining engineering measurements and observations, is being undertaken at Leichhardt colliery in Queensland. Headings are developed at present by shotfiring. The equipment being used in this study includes piezoelectric accelerometer assemblies to detect microseismic noise which is then transmitted to a surface base station by cable. Data are recorded on an analogue magnetic tape recorder and are also analysed on-line using a commercially-available acoustic emission pulse analyser. It is proposed to re-interpret recorded data using various modes of analysis and to interface a desktop computer to the existing system to permit continuous monitoring on the mine site. No outbursts have been recorded or analysed and only a limited number of develop- ment shots, and the resultant microseismic activity, have been recorded to date.

Jan 1, 1980

By Sneddon NW

Aberdare North Colliery is situated on the eastern boundary of the City of Cessnock in the Hunter Valley, New South Wales. Although the area is now noted for its wines and vineyards, the district has a long history based on coal mining. The richest coal seam in the Cessnock district is the Greta Seam, a low ash, high volatile steaming or gas making coal. The seam, up to 10 metres thick, extends over a large area surrounding the city of Cessnock and neighbouring townships such as Bellbird, Aber- dare, Kearsley, Neath, Ellalong, Kurri Kurri and Stanford Merthyr. The Aberdare Colliery, leases, which extend under Aberdare and Cessnock townships, were first worked in 1905 and continued developing pillar panels until the mine closed on 11 Nov- ember, 1960. Coal mining to this time consisted mainly of developing pillars to the 2.4 metre parting and, in some areas, dropping the top coal to the 6 metre parting, thus leaving the pillars intact, the top 1.8 metr-es of coal be- ing left untouched due to the high sulphur content. Aberdare North Colliery was opened in 1956 in order to recover and extract the pillar coal and tops left standing for over 40 years. During the pillar extraction phase the occurr

Jan 1, 1981

By M J. Nugus

A substantial cost is invested into the data collection phase of any exploration or development program; notwithstanding, it is impractical to expect a database of information can be collated to ensure a perfect geological interpretation. The question then becomes, is there a possible alternative interpretation and what is the likely impact of the variations? Modelling in 2005, of the Cosmo lode at Sunrise Dam Gold Mine, Western Australia led to consideration of the philosophical implications associated with resource management. It was concluded that several plausible geological models could be constructed from the known geological database. To varying degrees, this predicament is common to all geological reconstructions, as several alternative geological models can be generated at almost any stage that will impact on the resultant resource estimation and mine plan. The significance of that variation and the associated risk of multiple geological models (MGMs) requires due consideration. What is being suggested is that using plausible multiple geological models advances the holistic understanding of a mineral deposit within the bounds of the data collected, providing fluidity for updating geological knowledge and building inherent variability into the design and planning departments where variations of the geological models may materially impact on the resource performance.

Jan 1, 2006

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

Traditional methods for the production of transition metals from their ores usually include the electric arc smelting of the ore or concentrate to produce a ferroalloy. This is subsequently refined to produce either a ferroalloy or to produce the metal or metallic carbide. Recent trends in the treatment of iron ores have seen the development of many processes for solid state carbothermic reduction followed by melting of the prereduced iron to produce steel and similar types of processes are under consideration for the production of ferroalloys. There are clear potential savings in energy and control of emissions from such processes. This paper discusses some research which is currently underway at La Trobe University into the solid state carbothermic reduction of chromium and tungsten ores to produce the metallic ferroalloy or the carbide for subsequent further processing. The kinetics of the carbothermic reduction of both chromite and scheelite were found to be dominated by gaseous CO rather than by direct carbon reduction. However the diffusion of carbon into the ore is certainly an important feature of the process. The production of tungsten carbide from the metal is the slow step in tungsten reduction. The development of phases during reduction were studied using a scanning electron microscope and an electron probe and knowledge of the phases produced allows analysis of the reduction process.

Jan 1, 1997

Technical control in an industrY invariably leads to a basic contribution from the science of chemistry. It is interesting to note. that the change from the "Assay Office" to the "Chemical Laboratory" has already taken place on the majority of progressive mining fields.Although the serlvices of an efficient chemical staff are freely availed of by operating departments, it is not generally realized that practical chemistry is definitely expensive. A great deal of misplaced energy and expense can be involved in an enthusiastic research campaign where a full appreciation of laboratory economics and a balanced sense of analytical values are lacking.In order to supply data to the various departments concerning individual costs, it was decided at the North mine to issue a supplementary sheet concerning laboratory activities.The costs are compiled under the Unit System, which is based on a relative comparison between the total cost of the various determinations. carried out and the number of such determinatiQns converted to an equivalent aggregate of units.The introduction of the system necessitates the initial compiling of a table of relative units for the various estimations carried out on the works. Each laboratory will find it necessary to draw up such a table governed by local conditions, and, as will be anticipated, a relative comparison of the cost for any particular estimation will show a variation on a lead field, a copper field, or a steelworks, etc.This is due, of course, to the predominating type of routine work, cost of landing reagents, frequency of assays, etc. The satisfactory preparation of the Unit Table requires a good knowledge of laboratory procedure.

Jan 1, 1940

By Whiten W. J

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. In this way model parameters are obtained describing the behaviour of ball mills over a wide range of mill sizes and operating conditions. These parameters define the flow and breakage of each size fraction of ore in the mill. Flow of coarse particles through the mill is found to depend on the proportion of coarse particles present. The breakage rates of coarse particles are found to decrease markedly with mill diameter for mills over 3 m in diameter.Simulation of grinding circuit throughput at constant productsizing for different mill diameters shows that throughput is proportional to theoretical mill power consumption for mills up to about 3 m in diameter. Thereafter the throughput gradually falls below that indicated by power consumption, the decrease becoming quite significant for large diameter mills. Simple qualitative physical arguments are presented to explain this behaviour. The models developed have applications to ball mill scale up. Work on their further development is continuing.

Jan 1, 1982

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

Dewatering tailing slurries by mechanical means is often not possible and gravity and solar driven processes must be used. It has been shown previously that better use of gravity is achieved when the tailing is drained as it settles. Not only are more compact sediments obtained but also the dewatering is faster. From the results of laboratory and field tests reported here, equations were established which describe the evaporation and drainage components of the dewatering. These equations were used to calculate the effects of ponding depth, solids content of the tailing and clim- atic conditions on the time required to dewater the tailing. Since the calculations can be made with and without the drainage component, the advantages to be gained with drainage can be determined. The tailing used in the work was a clay slime from a sand washing operation. However, it is anticipated that this approach will be applicable to other similar tailing.

Jan 1, 1978

By M Pizey

After 60 years of operation, coal extraction at Solid Energy New ZealandÆs (SENZ) Strongman Mine, near Rapahoe is scheduled to end in early 2005. Up until 2003 the closure bond for Strongman Mine was only $930, and both SENZ and the West Coast Regional Council (WCRC) agreed that a more realistic level of bonding was required.   A conceptual closure plan has been developed by Golder Associates, and the cost of the work estimated. Closure includes decommissioning of equipment and facilities, rehabilitation and replanting of all disturbed areas and a period of maintenance and monitoring to verify that closure objectives have been met. Significant maintenance allowances are included to cover management of underground fire, subsidence and slope instability. These make up much of the potential ongoing environmental liability at the Strongman. All costs incurred beyond year 1 of closure are discounted to present value. Uncertainty in costs is addressed by Monte Carlo simulation, with an 80 % confidence level adopted.   A bond quantum of $3.0 million has been calculated for the first year of closure at Strongman. A three-year ærollingÆ bond is proposed. Progress will be reviewed annually, with the bond adjusted up or down accordingly. It is then renewed for a further three years. This allows for progressive return of the bond as rehabilitation objectives are met and verified. Similarly, if there are delays in meeting objectives, a proportion of the bond may need to be kept in place for a longer period than assumed. The level of bonding in place for the Strongman operation at any time in the future will therefore reflect the cost to complete the closure work programme.

Jan 1, 2004

This paper discusses design concepts in planning a large modern bulk terminal. The need is emphasised for a studied master plan, in-built materials handling flexibility and staged development. An integrated approach is advocated, combining functional purpose designed foundations and structures to serve their mechanical, electrical and environmental functions. Dry bulk and slurry handling are also compared in perspective.

Jan 1, 1983

The overwhelming weight of scientific opinion indicates that human activity is having a discernible and negative influence on the earthÆs climate system. The Australian Government, together with about 100 other nations, has accepted the findings of the Intergovernmental Panel on Climate Change third assessment report, released in 2001. This report was prepared by several hundred eminent scientists from all over the world, from various scientific disciplines and with differing opinions on global warming. The IPCC third assessment report contains a series of relevant, significant conclusions; for example, it finds that there is an increasing body of observations that gives a collective picture of a warming world and other changes in the climate system. Global average surface temperature increased over the past 100 years by about 0.6¦C. This may not seem much, but in the 900 years beforehand, the EarthÆs temperature remained relatively stable. The 20th century was the warmest of the past 1000 years in the northern hemisphere (there is much better information available from the northern hemisphere than the southern hemisphere). The 1990s were the warmest decade of the millennium in the northern hemisphere and 1998 was the warmest year. Although many factors influenced the EarthÆs climate, scientists are confident that greenhouse gas increases were the main factor contributing to global warming in the last 50 years of the 20th century. Increases in carbon dioxide, methane, troposhperic (lower atmosphere) ozone, halocarbons and nitrous oxide have all contributed to global warming. Combating climate change cannot be done without the cooperation of industry and the community at large. It is important that Government and industry work together to achieve greenhouse gas abatement while ensuring continued economic growth. The cause of the problem û the generation of greenhouse gas emissions û lies at the heart of the structure and size of modern economic activity. Greenhouse gas emissions are embedded in our way of life from our energy consumption patterns to the basic production of food. Moreover, the costs of the impacts of climate change to the earth will be potentially revolutionary, not merely evolutionary. It is in this light, acknowledging both the seriousness and nature of the problem before us that I want to reflect on the key drivers in the international climate change negotiations. A consideration of the past, present and future from what I see as the mid-way point in the process. In 1997, Parties agreed to adopt the Kyoto Protocol, which sets out mandatory targets for greenhouse gas emissions for developed countries.

Jan 1, 2002

By Bourgeois F

The population balance concept has provided a useful framework for the description of the operating behavior of the ball mill. This approach finds expression in the so-called selection breakage function model for batch and continuous mills. This model produces very good descriptions of the size distribution of the products from ball milling operations and the model is very useful for the description of batch and continuous mills and, when combined with models for classifiers and other unit operations, provides a solid basis for flowsheet simulation procedures. The breakage and selection function model is essentially descriptive and not predictive because the parameters in the model cannot as yet be related to the fundamental material properties of the material that is broken and to the fracture mechanics that govern the comminution of brittle particulate material during the rapid impact and compression events that occur with high frequency in a ball mill. The population balance approach smears over the individual processes and regards the ball mill as a continuum with breakage occurring continuously in time and space. New experimental techniques, particularly the adaptation of the Hopkinson bar as the ultrafast load cell (UFLC) to the problem of observing the extremely rapid impact fracture of particulate solids, have made it possible to make accurate and consistent measurements of particle strength, particle fracture energy and the single-impact breakage function. These quantitative measurements have been incorporated into a new conceptual model for the description of the ball mill. The model is based on identifying all events that give rise to particle breakage, and using the fundamental experimental data obtained on the UFLC and other single-particle fracture tests, the probabilities of these events can be independently determined. The distribution of impact energies that occur in the ball mill has been established by discrete element simulation of the media motion. The probabilistic description of the individual fracture events and the distribution of impact energies are combined to make a priori predictions of ball mill performance under a variety of operating conditions. The new model is used to calculate the selection and breakage functions for quartz in a small batch mill.

Jan 1, 1993

In recent years rehabilitation of mine sites has become a principal focus of mining legislation in Victoria. In previous eras, managed rehabilitation commenced, if at all, towards the end of mining operations. Planning for rehabilitation works now commences before an exploration licence is granted.The paper gives a brief overview of the requirements for rehabilitation under the Mineral Resources Development Act 1990, Extractive Industries Act 1966, and related environmental planning legislation including rehabilitation bonds and enforcement provisions.A brief review of the current taxation provisions is also included.

Jan 1, 1992

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995